The sor1 IP block needs the sor1_src clock to configure the clock tree
depending on whether it's running in HDMI or DP mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra210 XUSB subsystem has 3 power partitions which are XUSBA
(super-speed logic), XUSBB (USB device logic) and XUSBC (USB host
logic). Populate the device-tree nodes for these XUSB partitions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the DPAUX pinctrl states for the DPAUX nodes defining all three
possible states of "aux", "i2c" and "off". Also add the 'i2c-bus'
node for the DPAUX nodes so that the I2C driver core does not attempt
to parse the pinctrl state nodes.
Populate the nodes for the pinctrl clients of the DPAUX pin controller.
There are two clients for each DPAUX instance, namely the SOR and one of
the I2C adapters. The SOR clients may used the DPAUX pins in either AUX
or I2C modes and so for these devices we don't define any of the generic
pinctrl states (default, idle, etc) because the SOR driver will directly
set the state needed. For I2C clients only the I2C mode is used and so
we can simplify matters by using the generic pinctrl states for default
and idle.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the ACONNECT bus node for Tegra210 which is used to interface to
the various devices in the Audio Processing Engine (APE).
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add regulators to the Tegra210 Smaug DTS file including support for the
MAX77620 PMIC.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB mailbox interrupt for Tegra210 is 40 and not 49 which is for
the XUSB pad controller. For some Tegra210 boards, this is causing USB
connect and disconnect events to go undetected. Fix this by changing the
interrupt number for the XUSB mailbox to 40.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the XUSB controller on Jetson TX1. One of the USB 3.0 lanes goes
to an internal ethernet interface, while a second USB 3.0 lane supports
the USB-A receptacle on the I/O board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a chosen node to the device tree that contains a stdout-path
property which defines the debug serial port.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device tree node for the Tegra XUSB controller. It contains a
phandle to the XUSB pad controller for control of the PHYs assigned
to the USB ports.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add power supplies for the SD/MMC card slot. Note that vmmc-supply is
currently restricted to 3.3 V because we don't support switching the
mode yet.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device tree node for the MAX77620 PMIC found on the p2180
processor module (Jetson TX1). Also add supporting power supplies,
such as the main 5 V system supply.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Complement the GM20B GPU device tree node on Tegra210 with missing
properties to make it usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yX4c
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-gm20b' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt64
Merge "arm64: tegra: Enable GM20B GPU on Tegra210" from Thierry Reding:
Complement the GM20B GPU device tree node on Tegra210 with missing
properties to make it usable.
* tag 'tegra-for-4.7-gm20b' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add IOMMU node to GM20B on Tegra210
arm64: tegra: Add reference clock to GM20B on Tegra210
dt-bindings: Add documentation for GM20B GPU
dt-bindings: gk20a: Document iommus property
dt-bindings: gk20a: Fix typo in compatible name
The operating system driver can take advantage of the IOMMU to remove
the need for physically contiguous memory buffers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is required for the GPU to operate.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add nodes for the ChromeOS Embedded Controller and for the gas gauge
connected to the I2C bus that it controls.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra boards, the device-tree alias serial0 is used for the console
and so add the stdout-path information so that the console no longer
needs to be passed via the kernel boot parameters.
For tegra132-norrin the alias serial0 is not defined and so add this.
This has been tested on tegra132-norrin and tegra210-p2371-0000.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the "#power-domain-cells" property which was incorrectly
included by commit e53095857166 ("arm64: tegra: Add Tegra210
support").
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add gpio-keys nodes for the volumn controls, lid switch, tablet mode and
power button.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
[treding@nvidia.com: use symbolic names for input types and codes]
[treding@nvidia.com: use wakeup-source instead of gpio-key,wakeup]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a gpio-keys device tree node to represent the Power, Volume Up and
Volume Down keys found on Jetson TX1.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add initial device-tree support for Google Pixel C (a.k.a. Smaug) based
upon Tegra210 SoC with 3 GiB of LPDDR4 RAM.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "nvidia,wakeup-source" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The comment about the 8250 vs. APB DMA-enabled UART devices that was
added for Tegra20 and Tegra30 in commit b6551bb933 ("ARM: tegra: dts:
add aliases and DMA requestor for serial controller") introduced a typo
that has since spread to various other DTS include files. Fix all
occurrences of this typo.
Suggested-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When Tegra124 support was first merged the unit-addresses of all devices
were listed with a "0," prefix to encode the reg property's second cell.
It turns out that this notation is not correct, and the "," separator is
only used to separate fields in the unit address (such as the device and
function number in PCI devices), not individual cells for addresses with
more than one cell.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present
in the device-tree blob and if it is not then it fails to boot the kernel.
Add the chosen node so we can boot the kernel on Tegra132 Norrin with the
nvtboot bootloader.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Jetson TX1 Development Kit is the successor of the Jetson TK1. The
Jetson TX1 is composed of the Jetson TX1 module (P2180) that connects to
the P2597 I/O board. It comes with a 1200x1920 MIPI DSI panel connected
via the P2597's display connector.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P2597 I/O board is a carrier board for the Jetson TX1 module
and together they are also known as the Jetson TX1 Developer Kit. The
I/O board provides an RJ45 connector routed to the network adapter that
is part of the Jetson TX1 module. It exposes many other connectors such
as SATA, USB 3.0, HDMI, JTAG and PCIe, among others, as well. Dedicated
connectors allow display and camera modules to be attached. A full-size
SD slot is provided to extend storage beyond the 32 GiB of eMMC found
on the Jetson TX1 module.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Jetson TX1 is a processor module that features a Tegra210 SoC
with 4 GiB of LPDDR4 RAM attached, a 32 GiB eMMC and other essentials.
It is typically connected to some I/O board (such as the P2597) that has
the connectors needed to hook it up to the outside world.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P2571 is an internal reference design that's very similar to
the P2371, but targetting different use-cases.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P2371 is an internal reference design that uses a P2530
processor module hooked up to a P2595 I/O board and an optional display
module for a 1200x1920 MIPI DSI panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P2595 I/O board is used in several reference designs and has
the connectors to connect the P2530 compute module to the outside world.
It features a USB 3.0 network adapter, a USB 3.0 port, an HDMI port, a
SATA port, an audio codec, a microSD card slot and a display connector,
among others.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P2530 is a processor module used in several reference designs
that features a Tegra210 SoC, 4 GiB of LPDDR4 RAM, 16 GiB eMMC and other
essentials. It is typically connected to some I/O board that provides
the connectors needed to hook it up to the outside world.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Also known as Tegra X1, the Tegra210 has four Cortex-A57 cores paired
with four Cortex-A53 cores in a switched configuration. It features a
GPU using the Maxwell architecture with support for DX11, SM4, OpenGL
4.5, OpenGL ES 3.1 and providing 256 CUDA cores. It supports hardware
accelerated en- and decoding of various video standards including
H.265, H.264 and VP8 at 4K resolutions and up to 60 fps.
Besides the multimedia features it also comes with a variety of I/O
controllers such as GPIO, I2C, SPI, SDHCI, PCIe, SATA and XHCI, to
name only a few.
Add a SoC-level device tree file that describes most of the hardware
available on the SoC. This includes only hardware for which a device
tree binding already exists or which is trivial to describe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Norrin is a Tegra132-based FFD used as reference platform within NVIDIA.
Based on work by Allen Martin <amartin@nvidia.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
NVIDIA Tegra132 (also known as Tegra K1 64-bit) is a variant of Tegra124
but with 2 Denver CPUs instead of the 4+1 Cortex-A15. This adds the DTSI
file for the SoC, which is mostly similar to the one for Tegra124.
Based on work by Allen Martin <amartin@nvidia.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
