New firmware has defined new HCA capability field called "max_num_eqs",
that is the number of available EQs after subtracting reserved FW EQs.
Before this capability the FW reported the EQ number in "log_max_eqs",
the reported value also contained FW reserved EQs, but the driver might
be failing to load on 320 cpus systems due to the fact that FW
reserved EQs were not available to the driver.
Now the driver has to obtain max_num_eqs value from new FW to get real
number of EQs available.
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes: b21f502f84 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused netdev_registered_init/remove in en.h
Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails.
Remove extra white space
Fixes: 2a5e7a1344 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current check relies on function BDF addresses and can get
us wrong e.g when two VFs are assigned into a VM and the PCI
v-address is set by the hypervisor.
Fixes: 5c65c564c9 ('net/mlx5e: Support offloading TC NIC hairpin flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Alaa Hleihel <alaa@mellanox.com>
Tested-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem below. The problem can be reproduced by the
following steps:
1) Connecting all HiNIC interfaces
2) On server side
# sudo ifconfig eth0 192.168.100.1 up #Using MLX CX4 card
# iperf -s
3) On client side
# sudo ifconfig eth0 192.168.100.2 up #Using our HiNIC card
# iperf -c 192.168.101.1 -P 10 -t 100000
after hours of testing, we will see errors:
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
The errors are caused by the following problem.
1) The hinic_get_wqe() checks the "wq->delta" to allocate new WQEs:
if (atomic_sub_return(num_wqebbs, &wq->delta) <= 0) {
atomic_add(num_wqebbs, &wq->delta);
return ERR_PTR(-EBUSY);
}
If the WQE occupies multiple pages, the shadow WQE will be used. Then the
hinic_xmit_frame() fills the WQE.
2) While in parallel with 1), the free_tx_poll() checks the "wq->delta"
to free old WQEs:
if ((atomic_read(&wq->delta) + num_wqebbs) > wq->q_depth)
return ERR_PTR(-EBUSY);
There is a probability that the shadow WQE which hinic_xmit_frame() is
using will be damaged by copy_wqe_to_shadow():
if (curr_pg != end_pg) {
void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *cons_idx);
return shadow_addr;
}
This can cause WQE data error and you will see the above error messages.
This patch fixes the problem.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114813 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141440 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384500 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357414 ("Missing break in switch")
Addresses-Coverity-ID: 1357415 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114811 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410181 ("Missing break in switch")
Addresses-Coverity-ID: 1410184 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384501 ("Missing break in switch")
Addresses-Coverity-ID: 1398869 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410182 ("Missing break in switch")
Addresses-Coverity-ID: 1410183 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comments with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 114809 ("Missing break in switch")
Addresses-Coverity-ID: 114810 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114808 ("Missing break in switch")
Addresses-Coverity-ID: 114802 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114796 ("Missing break in switch")
Addresses-Coverity-ID: 114804 ("Missing break in switch")
Addresses-Coverity-ID: 114806 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114801 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114800 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114799 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 200521 ("Missing break in switch")
Addresses-Coverity-ID: 114797 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114794 ("Missing break in switch")
Addresses-Coverity-ID: 114795 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114792 ("Missing break in switch")
Addresses-Coverity-ID: 114793 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114791 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114790 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114789 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114788 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114787 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114784 ("Missing break in switch")
Addresses-Coverity-ID: 114785 ("Missing break in switch")
Addresses-Coverity-ID: 114786 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114782 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114781 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114780 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114777 ("Missing break in switch")
Addresses-Coverity-ID: 114778 ("Missing break in switch")
Addresses-Coverity-ID: 114779 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114910 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 143135 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114878 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114891 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114889 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-08-07
This series contains updates to i40e and i40evf only.
Sergey cleans up a duplicate call to i40e_prep_for_reset() during
shutdown.
YueHaibing cleans up i40evf by removing code that was never being used
or called within the driver.
Jake updates the ethtool statistics to use a helper function since many
of the statistics use the same basic logic for copying strings into the
supplied buffer. Cleaned up the use of a local variable that is no
longer needed or used. Fixed additional stats issues, including the
failure to update the data pointer which was causing stats to be
reported incorrectly.
Mariusz fixes a bug where there was an oversight in configuring FEC when
link settings were forced which was causing 25G link to be configured
incorrectly.
Piotr adds a missing return code for when the firmware returns a busy
state. Also added the process to command firmware to start
rearrangement when switching between old NVM structure to the new flat
NVM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE qps use a pair of physical queues (pq) received from the Queue Manager
(QM) - an offload queue (OFLD) and a low latency queue (LLT). The QM block
creates a pq for each TC, and allows RoCE qps to ask for a pq with a
specific TC. As a result, qps with different VLAN priorities can be mapped
to different TCs, and employ features such as PFC and ETS.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish not set offload_tc from offload_tc 0 and add getters and
setters.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API receives a priority and looks for the TC it is mapped to in the
operational DCBX configuration. The API returns QED_DCBX_DEFAULT_TC (0)
when DCBX is disabled.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For packets with computed IP/TCP/UDP checksum there is no need to tell
hardware to recompute it. For such kind of packets hardware expects the
packet to be at least 64 bytes and FCS to be computed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move checksum clearing outside of spinlock. The SKB is protected by
networking lock (HARD_TX_LOCK()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_tx_t return type for ndo_start_xmit function of macb driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a string instead of the error code. Since there is a
possibility that the driver can recover, classify it as a
warning instead of an error.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When backing device firmware reports an error, it provides an
error ID, which is meant to be queried for more detailed error
information. Currently, however, an error ID is not provided by
the Virtual I/O server and there are not any plans to do so. For
now, it is always unfilled or zero, so request_error_information
will never be called. Remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All control commands (soft commands) goes through only Queue 0
(control and data queue). So only queue-0 needs post_lock,
other queues are only data queues and does not need post_lock
Added a flag to indicate the queue can be used for soft commands.
If this flag is set, post_lock must be acquired before posting
a command to the queue.
If this flag is clear, post_lock is invalid for the queue.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation of lmac->dmacs is not being checked for allocation
failure. Add the check.
Fixes: 3a34ecfd9d ("net: thunderx: add MAC address filter tracking for LMAC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike fs.val.lport and fs.val.fport, cxgb4_process_flow_match()
sets fs.val.{l,f}ip to net-endian values without conversion - they come
straight from flow_dissector_key_ipv4_addrs ->dst and ->src resp. So
the assignment in mk_act_open_req() ought to be a straight copy.
As far as I know, T4 PCIe cards do exist, so it's not as if that
thing could only be found on little-endian systems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new layer for matching on geneve options. This allows
offloading filters configured to match geneve with options.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new push geneve option action. This allows offloading
filters configured to entunnel geneve with options.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of FLOW_DISSECTOR_KEY_ENC_IP to TC flower means that the ToS
and TTL of the tunnel header can now be matched on.
Extend the NFP tunnel match function to include these new fields.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TTL for encapsulating headers in IPv4 UDP tunnels is taken from a
route lookup. Modify this to first check if a user has specified a TTL to
be used in the TC action.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function accidentally failed to update the data pointer, which
caused the reported stats to be incorrect. Additionally, statistics
which follow queue stats in the output would potentially read non-zeroed
garbage data from the ethtool buffer.
This occurred because the data double pointer was not dereferenced
before incrementing the size.
Additionally, make sure this issue is more visible by adding a WARN_ONCE
to the i40e_get_ethtool_stats function. This warning will trigger
whenever the data pointer is not at the expected address, similar to the
check that we make in the i40e_get_stat_strings() function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During switching between old NVM structure approach (called structured
NVM) to new one (called flat NVM) or backward flash needs to be
rearranged to required NVM structure. This is a part of transition from
one NVM structure to another. The function is introduced to command
firmware to start rearrangement process.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Firmware can return a busy state, so the function return
I40E_ERR_NOT_READY.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 147e81ec75 ("i40e: Test memory before ethtool alloc succeeds")
code was added to handle ring allocation on systems with low memory.
It shadowed the ring parameter pointer by introducing a local ring
pointer inside the for loop. Most of the code in the loop already just
accessed the ring via &rx_rings[i]. Since most of the code already does
this, just remove the local variable.
If someone considers it worth keeping a local around, they should use it
for the whole section instead of just a couple of accesses.
This fixes a warning when -Wshadow is enabled
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c61c8fe1d5 ("i40e: Implement an ethtool private flag to stop
LLDP in FW") added an extra for-loop which added a shadowing 'i'
variable as the index.
However, the local variable i already exists, and we already use it as
a loop index. Additionally, at this point, there is no further use of
the variable, so it's safe to simply overwrite the variable contents.
This fixes a -Wshadow warning which has started being enabled on some
distributions
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Patryk Malek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTEMPORT MAC allows up to 8 filters to be programmed to wake-up
from LAN. Verify that we have up to 8 filters and program them to the
appropriate RXCHK entries to be matched (along with their masks).
We need to update the entry and exit to Wake-on-LAN mode to keep the
RXCHK engine running to match during suspend, but this is otherwise
fairly similar to Magic Packet detection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add cgroup local storage for BPF programs, which provides a fast
accessible memory for storing various per-cgroup data like number
of transmitted packets, etc, from Roman.
2) Support bpf_get_socket_cookie() BPF helper in several more program
types that have a full socket available, from Andrey.
3) Significantly improve the performance of perf events which are
reported from BPF offload. Also convert a couple of BPF AF_XDP
samples overto use libbpf, both from Jakub.
4) seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header.
Adds this action now to the seg6local BPF interface, from Mathieu.
5) Do not mark dst register as unbounded in MOV64 instruction when
both src and dst register are the same, from Arthur.
6) Define u_smp_rmb() and u_smp_wmb() to their respective barrier
instructions on arm64 for the AF_XDP sample code, from Brian.
7) Convert the tcp_client.py and tcp_server.py BPF selftest scripts
over from Python 2 to Python 3, from Jeremy.
8) Enable BTF build flags to the BPF sample code Makefile, from Taeung.
9) Remove an unnecessary rcu_read_lock() in run_lwt_bpf(), from Taehee.
10) Several improvements to the README.rst from the BPF documentation
to make it more consistent with RST format, from Tobin.
11) Replace all occurrences of strerror() by calls to strerror_r()
in libbpf and fix a FORTIFY_SOURCE build error along with it,
from Thomas.
12) Fix a bug in bpftool's get_btf() function to correctly propagate
an error via PTR_ERR(), from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The priority flow control statistics are laid out in the stats structure
using arrays. This made it unwieldy to use as part of an i40e_stats
array.
Add a new structure type, i40e_pfc_stats, and a helper function
i40e_get_pfc_stats which can return the stats for a given priority
value as an i40e_pfc_stats structure.
Use this to create an i40e_stats array, which we'll use to format and
copy the strings and stats into the supplied buffers.
This reduces even more boiler plate code in i40e_get_ethtool_stats and
i40e_get_stat_strings.
An alternative would be to modify the structure definition for the pfc
stats, but this is more invasive to the rest of the code base.
Note that a macro was used to setup the copy of stats from the
pf->stats, as this reduces the chance of typos in the code names. It
will produce a checkpatch.pl warning due to re-use of a macro argument.
In this case, it should be safe, as the macro will fail to compile in
cases where the argument is not a simple structure member name, and thus
arguments with side effects should not be an issue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VEB TC stats are currently implemented with separate parsing,
instead of using the i40e_stats array and associated helper functions.
This is likely because the stats rely on embedding the TC number into
the stat name.
Update i40e_add_stat_strings to take variadic arguments, and use these
to vsnprintf the i40e_stats string as a string containing format
specifiers.
Create a stats array for the VEB TC related stats,
i40e_gstrings_veb_tc_stats, and use this along with the helper functions
to remove the specialized boiler plate code.
Always call i40e_add_ethtool_stats for both this array and the general
VEB stats array. This ensures that we zero out any memory in case it was
not zero-allocated for us.
This ultimately results in less boiler plate code for the
i40e_get_stat_strings and i40e_get_ethtool_stats.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch configures FEC setting in i40e_force_link_state().
For some reason setting this field was overlooked thus causing
25G link to be configured incorrectly.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to the helper function to copy the ethtool stats strings, add
and use a helper function for copying the ethtool stats into the
supplied buffer.
Just like before, we use a macro to avoid having to pass ARRAY_SIZE
manually, so as to reduce chance of bugs.
Some of the stats, especially queue stats, are a bit trickier, and will
be handled in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the ethtool statistics use the same basic logic for copying
strings into the supplied buffer. A set of stats are stored in a const
array of i40e_stats structures, and we apply these all together.
Simplify the stats code by introducing a helper function which can take
a stats array and copy the strings into the buffer, updating the buffer
pointer as we go.
We use a macro to implement i40e_add_stat_strings so that ARRAY_SIZE can
be used on the array passed in. This ensures that we always use the
matching size in __i40e_add_stat_strings.
More complex stats currently do not use i40e_stats arrays, usually due
to custom formatted strings, or because the stats are not laid out in
the expected way. These stats will be updated to use the helper function
in separate future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function call to i40e_prep_for_reset() is duplicated in
i40e_shutdown routine and gets called before
i40e_enable_mc_magic_wake() which blocks it from being executed
correctly on system reboot or shutdown because adminq is already
disabled by first i40e_prep_for_reset() call.
Two register write calls are also duplicated.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__inet6_lookup_established() expect th->dport passed in host-endian,
not net-endian. The reason is microoptimization in __inet6_lookup(),
but if you use the lower-level helpers, you have to play by their
rules...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to give unicast traffic precedence over BUM traffic, configure
multicast-aware mode on all ports.
Under multicast-aware regime, when assigning traffic class to a packet,
the switch doesn't merely take the value prescribed by the QTCT
register. For BUM traffic, it instead assigns that value plus 8.
ETS elements for TCs 8..15 thus need to be configured as well. Extend
mlxsw_sp_port_ets_init() so that it maps each of them to the same
subgroup as their corresponding TC from the range 0..7, such that TCs X
and X+8 map to the same subgroup.
The existing code configures TCs with strict priority. So far this was
immaterial, because each TC had its own subgroup. Now that two TCs share
a subgroup it becomes important. TCs are prioritized in order of 7, 6,
..., 0, 15, 14, ..., 8: the higher TCs used for BUM traffic end up being
deprioritized. Since that's what's needed, keep that configuration as it
is, and configure the new TCs likewise.
Finally in mlxsw_sp_port_create(), invoke configuration of QTCTM to
enable MC-aware mode on each port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures if the Switch Priority to Traffic Class mapping
is based on Multicast packet indication. If so, then multicast packets
will get a Traffic Class that is plus (cap_max_tclass_data/2) the value
configured by QTCT.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CNP CoS queue is reserved for internal RDMA Congestion Notification
Packets (CNP) and should not be used for a TC. Modify the CoS queue
discovery code to skip over the CNP CoS queue and to reduce
bp->max_tc accordingly. However, if RDMA is disabled in NVRAM, the
the CNP CoS queue can be used for a TC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the .ieee_setapp() and ieee_delapp() DCBNL methods to support
DSCP. This allows DSCP values to user priority mappings instead
of using VLAN priorities. Each DSCP mapping is added or deleted one
entry at a time using the firmware API. The firmware call can only be
made from a PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export temperature sensor reading via hwmon sysfs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags field is almost getting full. Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to collect live firmware coredump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec. With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets. But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hotplug, the driver's open function can be called almost
immediately after power on reset. The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings. Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver gathers statistics using 2 mechanisms. Some stats are DMA'ed
directly from hardware and others are polled from the driver's timer.
Currently, we only adjust the DMA frequency based on the ethtool
stats-block-usecs setting. This patch adjusts the driver's timer
frequency as well to make everything consistent.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vnic_dev_register(), vnic_rq_alloc_bufs() and vnic_wq_alloc_bufs()
are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adjust_tail. There are no FW changes needed but add
a FW capability just in case there would be any issue with previously
released FW, or we will have to change the ABI in the future.
The helper is trivial and shouldn't be used too often so just inline
the body of the function. We add the delta to locally maintained
packet length register and check for overflow, since add of negative
value must overflow if result is positive. Note that if delta of 0
would be allowed in the kernel this trick stops working and we need
one more instruction to compare lengths before and after the change.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate
resource detruction scenario.
For mirror actions, such duplicate destruction leads to a crash as in:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add a call to mlxsw_afa_resource_del() in
mlxsw_afa_mirror_destroy() in order to clear that resource
from rule's resources.
Fixes: d0d13c1858 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each tc flower rule uses a hidden count action. As counter resource may
not be available due to limited HW resources, update _counter_create()
and _counter_destroy() pair to follow previously introduced symmetric
error condition handling, add a call to mlxsw_afa_resource_del() as part
of the counter resource destruction.
Fixes: c18c1e186b ("mlxsw: core: Make counter index allocated inside the action append")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.
The following sequence generated a crash:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.
Fixes: 140ce42121 ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.
For a conflicting actions configuration such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress mirror dev swp4
Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset of msix number for roce is different between different
revision id. We should get it from firmware, instead of a fix value.
This patch refines the msix allocation, make it compatible.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables 'max_frm' and 'tmp_mac_key' are being assigned,
but are never used,hence they are redundant and can be removed.
fix fllowing warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:461:6: warning: variable 'max_frm' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1685:31: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1855:41: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
