The receive hang detection routine was never being run when
PTP was enabled.
Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.
Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up. AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.
Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is an excessive space character between the word and the
period in the debug message. So delete it.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The macro E1000_success is meant to be E1000_SUCCESS. As the return
statement in the function is good as is, let's simply correct the
comment for this trivial matter.
Additionally E1000_ERR_HOST_INTERFACE_COMMAND is supposed to be
-E1000_ERR_HOST_INTERFACE_COMMAND.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes the following sparse warnings:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:254:13: warning:
symbol 'i40e_write_nvm_aq' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix missing include in Intel i40e driver. Without this include linux next
tree won't compile.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removing VF driver during device still in reset caused guest OS panic.
in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.
Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.
Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.
Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.
Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved." Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.
Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.
Also fix it to send the correct seid to aq for multicast promiscuous set.
Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes comment for reset reason
Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.
Also a small spelling correction in a comment.
Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local loopback should only be enabled for VSIs that are supporting
cascaded VEBs or VEPA setups. This is not the case here, and we need
to stop the VEB from echoing the VMDQ VSI packets back at the VSI.
Change-ID: I9dfb6ac79db24d04360d7efde62d81e20abc5090
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.
Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the HW registers are no longer in debug mode and many are
locked down for writes, we need to expose the Firmware API request
used to do writes on the driver's behalf.
Change-ID: I09a05c4dc9ea0b24c00193faac34d7799eaa8496
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds newly added FCoE files to the build but only if FCoE module is configured.
Also, updates i40e document for added FCoE support.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE specific code to existing i40e core driver to:-
1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds FCoE ( Fibre Channel Over Ethernet ) code for
Intel XL710 adapters. This patch is limited to only new FCoE
offloads code in newly added files by this patch and then
following patches in the series modifies rest of the existing
driver to enable FCoE with i40e driver.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a function, and associated calls, to flush writes to (read) the LPIC
MAC register before entering the shutdown flow. This fixes the problem
of the PHY never negotiating a 100M link (if both sides of the link support
EEE and 100M link) when Runtime PM is enabled.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The process of shutting down the system causes a call to the close PM
callback. The reset in close causes a loss of link, and the resultant
LSC interrupt causes the Runtime PM idle callback to be called. The
check for link (while link is down) in the idle callback is wiping the
information about the EEE ability of the link partner. The information is
still gone when the PHY is powered back up in the shutdown flow. This
causes EEE in S5 to fail when Runtime PM is active.
Save the link partner's EEE ability in the idle callback so that a Runtime
PM event will not cause a loss of this information.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On I217 and newer hardware, EEE is enabled in the PHY by the software
when link is up and disabled by the hardware when link is lost.
To enable EEE in Sx (When both ends of the link support, and are enabled
for, EEE and 100Mbps), we need to disable LPLU and configure the PHY to
automatically enable EEE when link is up, since there will be no software
to complete the task.
To configure this in the PHY, the Auto Enable LPI bit in the Low Power
Idle GPIO Control register must be set. For normal operation in S0, this
bit must be cleared.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding code to check and respond to previously ignored return values
from NVM access functions.
Issue discovered through static analysis.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modifying the jumbo frame workaround for 82579, i217 and i218 client parts
to increase the gap between the read and write pointers in the Tx FIFO.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of the code involved with returning the supported physical
layer is actually unused, so delete it.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ixgbe_write_mbx is called and no mbx->ops.write method
exists, no error code is returned. The corresponding read
function explicitly returns an error in such a case as do
other functions, so this appears to be a minor bug. Fix
it for consistency, and generate return values directly
to make things clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the function ixgbe_get_swfw_sync_semaphore, an incorrect
check was treating success as failure and vice-versa. This led
to manipulating the IXGBE_SWFW_SYNC register without holding
the software semaphore first, which is an error. In addition,
if getting the REGSMP bit in the IXGBE_SW_FW_SYNC register
timed out, no error code would be returned, making the caller
think that it had successfully acquired the lock. Fix both of
those issues and clean up the function a bit, such as make the
name in the comment match the function.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Failure to acquire the semaphore would lead to a spurious release
of the semaphore in several functions. Do not release a semaphore
that you did not get.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert some udelay calls to the preferred usleep_range.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes the AQTX answer comes back with no data, but we still want to print
the descriptor that got written back.
Change-ID: I5f734d99b4c95510987413893f0a34626571d474
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Give link a little more time to come back up after setting flow control
before resetting. In the new NVMs it is taking longer for link to come back.
This causes the driver to attempt to reset the link, which then errors
because the firmware was already in the middle of a reset. Also, initialize
err to 0.
Change-ID: I1cc987a944e389d8909c262da5796f50722b4d6b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jmyoungx@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reword the error messages. Also add a major version check because
We only want to warn on nvm_minor > expected_minor if
nvm_major == expected_major. Lastly, change an if to an else if
because the two statements will never evaluate to true at the same time.
Change-ID: I6ddf9986f26b35f6879cbeac4fcef04a8497a383
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy desc and buffer data even for ARQ events which return error status.
Previously, a check for NVM related AQ commands which is done later in this
function would not recognize that such a command was received and would
not clear nvm_busy flag. This would block access to NVM until a driver reset.
This will fix that.
Change-ID: If69ad74e165b56081c0686b97402511d2e2880c0
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We really don't need to delay an entire millisecond just to get into our
critical section. A microsecond will be sufficient, thank you.
Change-ID: I2d02ece6610007d98cabcb3f42df9a774bb54e59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware design requires that the driver avoid indicating
checksum offload success on some ipv6 frames with extension
headers.
The code needs to just check for the IPV6EXADD bit and if
it is set punt the checksum to the stack. I don't know why
the code was checking TCP on inner protocol, as that code
doesn't make any sense to me but seems wrong, so remove it.
Change-ID: I10d3aacdbb1819fb60b4b0eb80e6cc67ef2c9599
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements a state machine intended to support the userland tool for
updating the device eeprom. The state machine implements one-shot reads,
writes, multi-step write sessions, and checksum requests. If we're in the middle
of a multi-step write session, no one should fire off other writes, however, one
shot reads are valid. The userland tool is expected to keep track of its session
status, arrange the placement and ordering of the writes, and deal with the
checksum requirement.
This patch also adds nvmupdate support to ethtool callbacks.
The get_eeprom() and set_eeprom() services in ethtool are used here to
facilitate the userland NVMUpdate tool. The 'magic' value in the get and
set commands is used to pass additional control information for managing
the read and write steps.
The read operation works both as normally expected in the standard ethtool
method, as well as with the extra NVM controls. The write operation
works only for the expanded NVM functions - the normal ethtool method is
not allowed because of the NVM semaphore management needed for multipart
writes, as well as the checksum requirement.
Change-ID: I1d84a170153a9f437906744e2e350fd68fe7563d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
spotted by cppcheck
Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version number.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check and prints the error cause register value when
the hardware detects a malformed packet. This is a very unlikely
scenario but has been seen occasionally, so printing the message to
assist the user.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the display of the minimum link qualification check
if we might be in a virtual machine. This check is incorrect and
misleading in this case, since we actually don't really know what the
available bandwidth is. To do so, we simply check whether each function
on the bus matches our device id. If it doesn't the most likely scenario
is that we're directly assigned to a virtual machine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug in the misuse of the list_for_each macro to loop over every
entry in the bus_list. Instead of attempting to loop over the list from
a random entry point, go up to the bus and use the real list_head entry
point. This prevents the possible read or write of unallocated or
incorrectly addressed memory.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
