The mono output PGA input only has four possible sources, so
omit the rest.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new value argument needs proper shift to match the mask bit fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some unknown reason the parameters for snd_soc_test_bits() were in wrong
order:
It was:
snd_soc_test_bits(codec, val, mask, reg); /* WRONG!!! */
while it should be:
snd_soc_test_bits(codec, reg, mask, val);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
WM8804 can run with PLL frequencies of 256xfs and 128xfs for
most sample rates. At 192kHz only 128xfs is supported. The
existing driver selects 128xfs automatically for some lower
samples rates. By using an additional mclk_div divider, it
is now possible to control the behaviour. This allows using
256xfs PLL frequency on all sample rates up to 96kHz. It
should allow lower jitter and better signal quality. The
behavior has to be controlled by the sound card driver,
because some sample frequency share the same setting. e.g.
192kHz and 96kHz use 24.576MHz master clock. The only
difference is the MCLK divider.
Signed-off-by: Daniel Matuschek <daniel@matuschek.net>
Tested-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1381 and ADAU1781 audio
CODECs. The device is a low-power, 24-bit stereo audio CODEC with multiple
analog inputs and outputs, two digital microphone inputs and an I2S interface.
The device can be controlled either using I2C or SPI. The main difference
between the two variants is that the ADAU1781 has a freely programmable SigmaDSP
processor, while the ADAU1381 has a fixed function wind noise reduction filter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Analog Devices ADAU1361 and ADAU1761 CODECs.
The device is a a low-power, 24-bit stereo audio CODEC with multiple analog
input and outputs, one digital microphone input and an I2S interface. The device
can be controlled either via I2C or SPI. The main difference between the two
variants is that the ADAU1761 has a built-in SigmaDSP, while the ADAU1361 has
not.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADAU1X61 and ADAU1X81 are very similar in the digital domain, but are quite
different in the analog domain. This patch adds support for the common parts of
the ADAU1X61 and ADAU1X81 CODECs.
The patch also restores some of the alphabetical order in the Makfile and
Kconfig.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have defines for adsp messages best to consistently use them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit e5d80e82e3 (ASoC: sgtl5000: Convert to use regmap directly) a
kernel oops is observed after a suspend/resume sequence.
The kernel oops happens inside sgtl5000_restore_regs() as codec->reg_cache is no
longer a valid pointer.
Add the remaining register entries into sgtl5000_reg_defaults[] and remove
sgtl5000_restore_regs() completely, which allows suspend/resume to work fine and
make the code simpler.
Tested on a im53-qsb board.
Reported-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Having the binary ones complement operator in the new bitmak value makes the
code hard to read.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Documentation has been updated to reflect the change.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Documentation has been updated to reflect the change.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add "depends on I2C" to shut up the build errors from randconfig.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the clock divisor and multiplier NI, MI values for audio
sampling frequencies 44100 and 48000 Hz and PCLK 19.2 MHz. This is useful
for the Odroid X2/U2 boards when the codec works in master mode and its
MCLK clock is fed from the I2S CDCLK output.
Signed-off-by: Chen Zhen <zhen1.chen@samsung.com>
[s.nawrocki@samsung.com: edited the commit description]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A small set of driver fixes, nothing remarkable in itself or of any
relevance outside of the driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0trh
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-rc5-drivers' into asoc-linus
ASoC: Driver fixes for v3.15
A small set of driver fixes, nothing remarkable in itself or of any
relevance outside of the driver.
# gpg: Signature made Wed 14 May 2014 12:49:57 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Let the ALC5623 codec be instantiated from DT. Add a simple binding
for the additional control register and the jack detect register.
Also, add a prompt to the Kconfig entry for this CODEC, so that it can
be selected. Since kirkwood-t5325.c will no longer be used, we need to
be able to enable the CODEC in the mvebu_v5_defconfig etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using a proper do-while loop here instead of a open-coded goto loop is both
cleaner and shorter.
Also fixes the following warnings from smatch:
sound/soc/codecs/ad1980.c:213 ad1980_reset() info: loop could be replaced with if statement.
sound/soc/codecs/ad1980.c:212 ad1980_reset() info: ignoring unreachable code.
sound/soc/codecs/ad1980.c:215 ad1980_reset() info: ignoring unreachable code.
While we are at it also change retry_cnt to unsigned int, using u16 for a
on-stack loop counter doesn't make that much sense.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This looks like a copy-paste bug, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rtd->codec does not necessarily point to the CODEC instance for which the
callback was called (e.g. for CODEC<->CODEC or multi-CODEC links). Use
dai->codec instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
rtd->codec does not necessarily point to the CODEC instance for which the
callback was called (e.g. for CODEC<->CODEC or multi-CODEC links). Use
dai->codec instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Microphone bias level configuration register can configure voltage between
2.2 V and 2.8 V but doesn't manage is voltage on or off. Microphone bias
on/off state is controlled by "MICBIAS" DAPM widget.
Therefore there is no need to update bias voltage conditionally depending on
jack state each time when codec goes to SND_SOC_BIAS_ON state and setting
can be moved to max98090_probe() as driver currently doesn't support other
levels than 2.8 V.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
BCL is being configured in two places producing a warning message.
Make sure we only configure BCLK once and when we are master.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add ACPI ID for MAX98090 and ACPI 5 I2C device probing support.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure the cache is fully flushed at resume time.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure we reset codec and clear any IRQs on resume. This matches
the init sequence in probe.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reset needs to wait 20ms before other codec IO is performed. This wait
was not being performed. Fix this by making sure the reset register is not
restored with the cache, but use the manual reset method in resume with
the wait.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
TLV for digital sidetone volume is wrong, this fix matches it to the
datasheet.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Additionally to the ak4642 pll frequencies the ak4648 also supports 13MHz,
19.2MHz and 26MHz. This adds support for these frequencies.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently unused, this is done to let the driver distinguish between
the different supported codec types in later patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALC and ALC Zero crossing detection has been enabled unconditionally.
Add controls for this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The register CLASS_D_CONTROL_1 is marked as volatile because it contains
a bit, DAC_MUTE, which is also mirrored in the ADC_DAC_CONTROL_1
register. This causes problems for the "Speaker Switch" control, which
will report an error if the CODEC is suspended because it relies on a
volatile register.
To resolve this issue mark CLASS_D_CONTROL_1 as non-volatile and
manually keep the register cache in sync by updating both bits when
changing the mute status.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
We may read an unexpected value when detemining which codec is attached.
In that case, either a unsupported codec is attached or something wrong
with I2C. The driver will not work properly on both cases. So we return
an error for that.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Return statements in functions returning bool should use
true/false instead of 1/0.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch moves the private register settings from probe() to reg_default
struct.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic Low Power Stereo I2C CODEC
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for RPDNEN, NSHHPEN, BRIDGOFF, CPWMEN and PNDLSL, and add DT
bindings to access them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the Realtek ALC5645 codec driver. It is the base
version that because the jack detect function is not implemented to
it, the headphone and AMIC1 are not workable. We will fill up the
further functions later.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that INPUT is required for the CS42L52 and WM8962 we can remove the
IS_ENABLED(INPUT) check in the drivers.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm_regulator_bulk_get() can make the code cleaner and smaller as we
do not need to call regulator_bulk_free() in the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building ARM randconfig got into a situation where CONFIG_INPUT
is turned off and SND_SOC_ALL_CODECS is turned on, which failed
for two codecs trying to use the input subsystem. Some other
drivers also select one of these codecs and consequently need an
explicit dependency added.
Appending to the dependency list seems the easiest way out,
since this is not a practical limitation. If anyone really
needs to build these codecs for a kernel with no input support,
a more sophisticated solution can be implemented.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xia Kaixu <kaixu.xia@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
49101a25ac "ASoC: cq93vc: Remove the set_cache_io() entirely from
ASoC probe" introduced the cq93vc_get_regmap function that has an
obvious build error referring to the 'codec' variable that is not
declared anywhere"
sound/soc/codecs/cq93vc.c: In function 'cq93vc_get_regmap':
sound/soc/codecs/cq93vc.c:157:34: error: 'codec' undeclared (first use in this function)
struct davinci_vc *davinci_vc = codec->dev->platform_data;
^
This changes the code to compile again, presumably in the way it was
intended. Not tested.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch correct rt5640's device ID
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds devicetree support for mc13783-codec.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the rt5639 support to the OF match table.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm_regulator_bulk_get() can make the code cleaner and smaller as we
do not need to call regulator_bulk_free() in the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm_regulator_bulk_get() can make the code cleaner and smaller as we
do not need to call regulator_bulk_free() in the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm_regulator_bulk_get() can make the code cleaner and smaller as we
do not need to call regulator_bulk_free() in the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm_regulator_bulk_get() can make the code cleaner and smaller as we
do not need to call regulator_bulk_free() in the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using devm_regulator_bulk_get() can make the code cleaner and smaller as we
do not need to call regulator_bulk_free() in the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The AK4104 has only one power supply, called VDD. Enable it as long as
the codec is in use.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Create an explicit of_match_table entry for MAX98095 codec. Also
add a binding Documentation for this compatible string.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have been using rt5640.c codec driver with RT5642 codec chip before commit
022d21f004 ("ASoC: rt5640: add rt5639 support"). That commits starts using
device ID reading in reset register for adding device specific controls and
routes runtime.
Now since device ID appears to be different between RT5640 and RT5642 the
driver doesn't add those controls and routes that are valid also on RT5642.
Fix this by adding a device ID found by debugging and minimal code for
supporting RT5642.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for componentisation of the kcontrol helpers use
snd_soc_kcontrol_codec() instead of snd_kcontrol_chip().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The REVID mask was changed by commit a1253ef6d3
"ASoC: cs42l51: split i2c from codec driver". Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code missed a gpio_free() call in cs42l73_i2c_remove().
Convert to use devm_gpio_request_one() to fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code missed a gpio_free() call in cs42l52_i2c_remove().
Convert to use devm_gpio_request_one() to fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the i2c bus code from the codec driver and creates seperate i2c driver.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 0cd257bf9b, "ASoC: alc5623:
Convert to direct regmap API usage" broke probing of the codec,
because of wrong endinness of the ID and codec version read from the
device. Fix this by removing the existing flipping of the endiannes,
and extracting the codec type byte from the word from the regmap.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the second tlv320aic3x instance fails to
be probed from DT if the reset pin is shared with
the first one.
This patch fixes it by moving the list add of the
reset pin into the i2c_probe method.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The macro's name is SOC_ENUM, not SOC_VALUE.
Fixes: e13dd8ce ("ASoC: wm8997: Replace usage deprecated MUX/ENUM macros")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SOC_VALUE_ENUM, SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated
and merely an alias for SOC_ENUM, SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace
the deprecated macros so we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VIRT_MUX and SOC_DAPM_ENUM_VIRT are deprecated and merely an alias
for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so we can
eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VIRT_MUX, SND_SOC_DAPM_VIRT_MUX_E and SOC_DAPM_ENUM_VIRT are
deprecated and merely an alias for SND_SOC_DAPM_MUX, SND_SOC_DAPM_MUX_E and
SOC_DAPM_ENUM. Replace the deprecated macros so we can eventually remove their
definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SOC_VALUE_ENUM is deprecated and merely an alias for SOC_EMUM. Replace the
deprecated macros so we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SOC_VALUE_ENUM, SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated
and merely an alias for SOC_ENUM, SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace
the deprecated macros so we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SOC_VALUE_ENUM is deprecated and merely an alias for SOC_ENUM. Replace the
deprecated macro so we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VIRT_MUX and SOC_DAPM_ENUM_VIRT are deprecated and merely an alias
for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so we can
eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VIRT_MUX and SOC_DAPM_ENUM_VIRT are deprecated and merely an alias
for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so we can
eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAPM_VALUE_MUX and SOC_DAPM_VALUE_ENUM are deprecated and merely an
alias for SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the deprecated macros so
we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SOC_VALUE_ENUM, SND_SOC_DAPM_VIRT_MUX and SOC_DAPM_ENUM_VIRT are deprecated and
merely an alias for SOC_ENUM, SND_SOC_DAPM_MUX and SOC_DAPM_ENUM. Replace the
deprecated macros so we can eventually remove their definition.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_match_ptr is defined in of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following compilation warnings:
sound/soc/codecs/pcm512x.c:520:12: warning: ‘pcm512x_suspend’ defined but not used [-Wunused-function]
sound/soc/codecs/pcm512x.c:545:12: warning: ‘pcm512x_resume’ defined but not used [-Wunused-function]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TI STA350 is an integrated 2.1-channel power amplifier that is
controllable over I2C. This patch adds an ASoC driver for it.
At a glance, this chip is very similar to the STA320 for which a driver
already exists. In details, however, the register maps contain subtle
differences which made a whole new driver easier to write and maintain.
[daniel@zonque.org: cleanups, DT property rework, rebased on asoc-next]
Signed-off-by: Sven Brandau <brandau@gmx.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The port driver only used to register component and dmaengine pcm.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch adds the string "rt5639" to the list of I2C device IDs.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch moves the idle_bias_off setting to struct "soc_codec_dev_rt5640".
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch removes the unused or incorrect setting of clock source.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to identify clearly, the patch renames the function
"check_sysclk1_source" to "is_sys_clk_from_pll".
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to prevent the redundant memory usage, the pre-allocated size of
reg_default should be remove.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch fixes the defect in case of resume which doesn't sync the cache.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC controls snd_kcontrol_chip() currently returns a pointer to the
CODEC that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_codec() helper function that will hide the implementation
details of how the CODEC for a control can be obtained. This will allow us to
change this easily in the future.
The patch also updates all CODEC drivers to use the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some thing Likes:
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> sound/soc/codecs/wm8997.c:1084:15: sparse: symbol \
'wm8997_get_regmap' was not declared. Should it be static?
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we can set the CODEC I/O while snd_soc_register_codec(), so the
calling of set_cache_io() from CODEC ASoC probe could be removed
entirely.
And then we can set the CODEC I/O in the device probe instead of
CODEC ASoC probe as earily as possible.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are no OSR controls on outputs 1-4 on wm5110, however when these
were removed the ones on output 5 and 6 were also accidentally removed,
but those actually exist. This patch adds these controls back in.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DA732X_ID_MAJOR_MASK is 0xF0, so the major id is
(reg & DA732X_ID_MAJOR_MASK) >> 4.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
BIT[0:2] of register 01h is REVID, so the mask for REVID should be 0x7.
Also updates the code to use CS42L52_CHIP_REV_MASK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 5d6be5aa ("ASoC: codec: Simplify ASoC probe code.") left variable
'ret', whose value is returned, uninitialized. Since it is not used
otherwise, remove it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix checking return value of regmap_read().
Also fix reporting the chip_id value. CS42XX8_CHIPID_CHIP_ID_MASK is 0xF0,
so the chip_id value is (val & CS42XX8_CHIPID_CHIP_ID_MASK) >> 4).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Paul Handrigan <paul.handrigan@cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
alc5632_probe() returns ret, yet it is not initialized or set anywhere.
This ends up causing the function to appear to fail, and audio not to
work on the Toshiba AC100, with my compiler at least.
This function used to set ret in all cases, but recent cleanup removed
that.
Fixes: 5d6be5aa6b ("ASoC: codec: Simplify ASoC probe code.")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is mostly a few additional fixes from Lars-Peter, a new driver and
cleaning up a git failure with merging the Intel branch (combined with
an xargs failure to pay attention to error codes). The history lists a
bunch of additional commits for the branch but the content of those
commits is actually present already but not recorded in history due to
git failing. Unfortunately xargs is used in the merge script and it
doesn't do a good job of noticing errors from the commands it invokes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nG53
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15-2' into asoc-next
ASoC: Updates for v3.15
This is mostly a few additional fixes from Lars-Peter, a new driver and
cleaning up a git failure with merging the Intel branch (combined with
an xargs failure to pay attention to error codes). The history lists a
bunch of additional commits for the branch but the content of those
commits is actually present already but not recorded in history due to
git failing. Unfortunately xargs is used in the merge script and it
doesn't do a good job of noticing errors from the commands it invokes.
# gpg: Signature made Thu 13 Mar 2014 14:25:44 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C5oo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15' into asoc-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
# gpg: Signature made Wed 12 Mar 2014 23:05:45 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
This patch adds support for the Cirrus Logic CS42448/CS42888 Audio CODEC that
has six/four 24-bit AD and eight 24-bit DA converters.
[ CS42448/CS42888 supports both I2C and SPI control ports. As initial patch,
this patch only adds the support for I2C. ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The shift values for the ADC,PCM, and Analog kcontrols were wrong causing wrong values for the SOC_DOUBLE_R_SX_TLV macros
Fixed the TLV for aout_tlv to show -102dB correctly
Fixes: 1d99f2436d (ASoC: core: Rework SOC_DOUBLE_R_SX_TLV add SOC_SINGLE_SX_TLV)
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The mask bits values were wrong for the SOC_VALUE_ENUM_SINGLE for the PCM/ADC Swap controls
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The mask bits values were wrong for the SOC_VALUE_ENUM_SINGLE for the mono mix controls.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
With CODEC to CODEC links rtd->codec does not necessarily point to the driver's
CODEC. CODEC drivers should always use dai->codec and never even look at the PCM
runtime.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The kfree call is not necessary, but we need to call snd_soc_unregister_codec()
in remove().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There was a overlap between the snd_soc_codec_set_cache_io() cleanup and the
addition of the sirf-audio-codec resulting in the sirf-audio-codec driver still
using the old signature of snd_soc_codec_set_cache_io(), which will cause a
compile error. Since the core is able to automatically setup IO for this driver
we can just remove both the snd_soc_set_cache_io() call and the control_data
assignment.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Regulator code keep count of enables and disables. Double disable
causes an ugly warning.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver assigns a value to the control_data field of the driver's state
struct, but never reads it again. Which means it is unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove snd_soc_codec_set_cache_io(codec, 8, 8, SND_SOC_REGMAP) call
and codec->control_data = aic31xx->regmap assignment since that
already done by core.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix "warning: unused variable 'aic31xx'" from function 'aic31xx_clk_off'.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This commit adds a bare bones driver support for TLV320AIC31XX family
audio codecs. The driver adds basic stereo playback trough headphone
and speaker outputs and mono capture trough microphone inputs.
The driver is currently missing support at least for mini DSP features
and jack detection. I have tested the driver only on TLV320AIC3111,
but based on the data sheets TLV320AIC3100, TLV320AIC3110, and
TLV320AIC3120 should work Ok too.
The base for the implementation was taken from:
git@gitorious.org:ti-codecs/ti-codecs.git ajitk/topics/k3.10.1-aic31xx
-branch at commit 77504eba0294764e9e63b4a0c696b44db187cd13.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regmap should handle any byte ordering issues required, it is looking for
a byte stream from the bus, so don't set 16 bits per word. This is likely
to have tested out OK due to use of an unmerged SPI controller driver.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.
Since the only control type that left is SND_SOC_REGMAP, so remove it. Drop
the control params and add struct regmap *regmap to simplify the code.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 88pm860 is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced in commit
f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Fixes: f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The si476x is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced commit
d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Fixes: d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The tlv320aic32x4 related lines were wrongly placed after tlv320aic3x lines.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The reference clock path on newer IP FLLs requires a different
configuration, and should avoid integer mode operation. This patch adds
support for both the new encoding and updates the calculation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No part of the FLL calculation depends on the value determined for the
gain but the gain does depend on other values. In preparation for future
updates this patch moves the gain to be the last thing calculated.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
OUTDIV will remain unchanged whilst the rest of the FLL configuration is
calculated so do this first.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we now calculate the FLL configuration at a later stage in the
process the fout member of the FLL structure will contain the desired
Fout frequency so no need to pass this in seperately.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the FLL configuration is calculated before it is known which
FLL path the configuration will be applied to. Newer versions of the IP
have differences in the configuration required for each FLL path, which
makes it complicated to calculate the FLL configuration in advance.
This patch simply checks the validity of a requested input and output
frequency before we know which FLL path they will be applied to and
saves the actual calculation of the configuration until we know where
the settings will be applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we know in arizona_apply_fll if we are setting the sync or ref
path there is no need to set the outdiv seperately anymore. This patch
moves this from arizona_enable_fll to arizona_apply_fll.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Improve readability by adding defines for some of the constants
associated with FLL configuration.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
One is not a valid value for the OUTDIV start searching at 2 instead.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes the following build errors when aic23 is configured as
module:
>> ERROR: "tlv320aic23_probe"
>> [sound/soc/codecs/snd-soc-tlv320aic23-i2c.ko] undefined!
>> ERROR: "tlv320aic23_regmap"
>> [sound/soc/codecs/snd-soc-tlv320aic23-i2c.ko] undefined!
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move to the new style of defining the bus interfaces in separate modules
in order to simplify dependencies.
Signed-off-by: Mark Brown <broonie@linaro.org>
tlv320aic23 chip control interface may work in either I2C or SPI mode
depending on the MODE pin state. Functionality and register layout are
independent of the control mode.
Implement bus-specific parts as separate modules.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of directly checking the 'active' field of the CODEC struct add a new
helper function that will return either true or false depending on whether the
CODEC is active. This will make the migration to the component level easier.
The patch also updates all CODEC drivers that check the active attribute to use
the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SiRF internal audio codec is integrated in SiRF atlas6 and prima2 SoC.
Features include:
1. Stereo DAC and ADC with 16-bit resolution amd 48KHz sample rate
2. Support headphone and/or speaker output
3. Integrate headphone and speaker output amp
4. Support LINE and MIC input
5. Support single ended and differential input mode
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
--v5:
1. Drop all inlines.
2. Reordering the Kconfig and Makefile
3. Remove the sirf_audio_codec_reg_bits struct, use the new controls instead it.
4. Add some SND_SOC_DAPM_OUT_DRV instead of HP and SPK enable driver
5. Add audio codec clock supply instead of adc event callback
6. Fixed playback and capture can't concurrent work bug.
--
.../devicetree/bindings/sound/sirf-audio-codec.txt | 17 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 1 +
sound/soc/codecs/sirf-audio-codec.c | 533 ++++++++++++++++++++
sound/soc/codecs/sirf-audio-codec.h | 75 +++
5 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
create mode 100644 sound/soc/codecs/sirf-audio-codec.c
create mode 100644 sound/soc/codecs/sirf-audio-codec.h
Signed-off-by: Mark Brown <broonie@linaro.org>
The firmware files can be quite large and allocating the whole firmware
a single DMA safe buffer can be problematic if the system is under a
high memory load. Ease the requirements slightly by writing the firmware
out in page sized chunks.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
cs4271_common_probe() is called from cs4271_i2c_probe() but defined in
CONFIG_SPI_MASTER block, thus it results in a build error when
CONFIG_SPI_MASTER=n:
sound/soc/codecs/cs4271.c:721:2: error: implicit declaration of function ‘cs4271_common_probe’ [-Werror=implicit-function-declaration]
Move the function out of #if block.
Fixes: d6cf89ee07 ('ASoC: cs4271: claim reset GPIO in bus probe function')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver uses automatic IO setup, which will also initialize the control_data
field of the CODEC, no need to do it manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pre-merge code was using direct hw_read() calls as an out of framework
way of doing volatile register I/O when not using regmap. This has never
functioned correctly in mainline due to the regmap conversion, the
hw_read() implementation still does caching. In order to facilitate
removal of the subsystem level I/O code convert to use snd_soc_read(),
there should be no functional impact.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
With the ongoing component-ization of the ASoC framework and the continuing
migration to using regmap for IO the control_data field of the snd_soc_codec
struct will eventually be removed. Prepare the wm5192, wm5110 and wm8997
drivers for this by using arizona->regmap instead of accessing the CODEC's
control_data field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8763 driver uses regmap for IO which means that codec->cache_sync is not
used. The line was added in commit d3398ff ('ASoC: Convert WM8753 to direct
regmap API usage'). Presumably this was meant to be regcache_mark_dirty(), but
since we already call regcache_mark_dirty() in the core when suspending the
CODEC it is safe to just remove the line.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a typo in the Limiter2 Release Rate control, a wrong enum for
Limiter1 is assigned. It must point to Limiter2.
Spotted by a compile warning:
In file included from sound/soc/codecs/sta32x.c:34:0:
sound/soc/codecs/sta32x.c:223:29: warning: ‘sta32x_limiter2_release_rate_enum’ defined but not used [-Wunused-variable]
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
include/sound/soc.h:275:18: note: in definition of macro ‘SOC_ENUM_DOUBLE_DECL’
struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/codecs/sta32x.c:223:8: note: in expansion of macro ‘SOC_ENUM_SINGLE_DECL’
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
The driver reads from the DC offset control registers during callibration
but since the registers are marked as volatile and there is a register
cache the values will not be read from the hardware after the first reading
rendering the callibration ineffective.
It appears that the driver was originally written for the ASoC level
register I/O code but converted to regmap prior to merge and this issue
was missed during the conversion as the framework level volatile register
functionality was not being used.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Cc: stable@vger.kernel.org
The codec->control_data contains a pointer to the device's regmap struct. But
wm8994_bulk_write() expects a pointer to the parent wm8998 device.
The issue was introduced in commit d9a7666f ("ASoC: Remove ASoC-specific
WM8994 I/O code").
Fixes: d9a7666f ("ASoC: Remove ASoC-specific WM8994 I/O code")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
With the ongoing component-ization of the ASoC framework and the continuing
migration to using regmap for IO the control_data field of the snd_soc_codec
struct will eventually be removed. Prepare the wm8962 driver for this by using
wm8962->regmap instead of accessing the CODEC's control_data field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the ongoing component-ization of the ASoC framework and the continuing
migration to using regmap for IO the control_data field of the snd_soc_codec
struct will eventually be removed. Prepare the wm8996 driver for this by using
wm8996->regmap instead of accessing the CODEC's control_data field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 88b5bdfd (ASoC: wm8993: drop regulator_bulk_free of devm_ allocated
data) eliminated the last user of driver data pointer 'wm8993' in function
wm8993_remove() - Thus remove it. Detected by Coverity: CID 1186208.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the ongoing component-ization of the ASoC framework and the continuing
migration to using regmap for IO the control_data field of the snd_soc_codec
struct will eventually be removed. Prepare the da732x driver for this by using
da732x->regmap instead of accessing the CODEC's control_data field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The da732x driver no longer uses the ASoC level register cache but the
cache size setting had been left in the driver by mistake. Remove it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rearrange clock tree shutdown to disable them in the reversed order of
startup. First disable all dividers, then PLL followed by master clock.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support regulators to power up the codec. This patch also enables the
AVDD LDO if no AV regulator was found.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for a master clock passed through DT. The master clock of
the codec is only active when the codec is in use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
... to make clear the meaning of the argument.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
... to make clear the meaning of the argument.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macros. No functional change at all.
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
