Ensures that we report the key and indirection table the NIC is using,
rather than (if setting them failed earlier) what we wanted it to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should
only be used if it is not possible to continue without potential harm;
and since the non-DEBUG driver will continue regardless (as the BUG_ON is
compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver.
So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID
or the newly defined EFX_WARN_ON_ONCE_PARANOID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defalconisation removed one of the string arguments, but missed the
corresponding %s.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for FATSOv2 to the driver. FATSOv2 offloads far more of the task
of TCP segmentation to the firmware, such that we now just pass a single
super-packet to the NIC. This means TSO has a great deal in common with a
normal DMA transmit, apart from adding a couple of option descriptors.
NIC-specific checks have been moved off the fast path and in to
initialisation where possible.
This also moves FATSOv1/SWTSO to a new file (tx_tso.c). The end of transmit
and some error handling is now outside TSO, since it is common with other
code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_TRIGGER_INTERRUPT does not work on the SFC9140, as used in the
sfn7x42q and sfn7x24f.
Check for this using the MCDI workaround mechanism.
The command is only used during self test. If it's not supported, skip
the interrupt test.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IP stack passes SKBs the sfc driver puts them in 2 different TX
queues (called partners), one for checksummed and one for not checksummed.
If the SKB has xmit_more set the driver will delay pushing the work to the
NIC.
When later it does decide to push the buffers this patch ensures it also
pushes the partner queue, if that also has any delayed work. Before this
fix the work in the partner queue would be left for a long time and cause
a netdev watchdog.
Fixes: 70b33fb ("sfc: add support for skb->xmit_more")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commits:
d92916f71a ("sfc: Own header for nic-specific sriov functions,")
25672dba95 ("sfc: Enable VF's via a write to the sysfs file
sriov_numvfs")
As they break the build with SRIOV disabled and there is no
easy way to fix it the way things are arranged.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also add dummy functions where required to avoid NULL pointer dereference.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch in preparation for the upcoming EF10 sriov support.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series provides a base and cleanup for the
upcoming EF10 SRIOV support.
This patch moves the VF state into siena_nic_data as a basis to
save the VF state based on nic type.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Nikolay Aleksandrov. In efx_init_port() we call
efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls
efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this
lock is uninitialised, because we haven't called register_netdevice() yet.
So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before
doing anything else.
The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the
corresponding check.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCDI command times out (whether or not we find it
completed when we poll), call efx_mcdi_abandon(), which tells
all subsequent MCDI calls to fail-fast, and queues up an FLR.
Because an FLR doesn't lead to receiving any reboot even from
the MC (unlike most other types of reset), we have to call
efx_ef10_reset_mc_allocations.
In efx_start_all(), if a reset (of any kind) is pending, we
bail out.
Without this, attempts to reconfigure (e.g. change mtu) can
cause driver/mc state inconsistency if the first MCDI call
triggers an FLR.
For similar reasons, on EF10, in
efx_reset_down(method=RESET_TYPE_MCDI_TIMEOUT), set the number
of active queues to zero before calling efx_stop_all().
And, on farch, in efx_reset_up(method=RESET_TYPE_MCDI_TIMEOUT),
set active_queues and flushes pending & outstanding to zero.
efx_mcdi_mode_{poll,event}() should not take us out of fail-fast
mode. Instead, this is done by efx_mcdi_reset() after the FLR
completes.
The new FLR reset_type RESET_TYPE_MCDI_TIMEOUT doesn't really
fit into the hierarchy of reset 'scopes' whereby efx_reset()
decides some resets subsume others. Thus, it uses separate logic.
Also, fixed up some inconsistency around RESET_TYPE_MC_BIST,
which was in the wrong place in that hierarchy.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove trailing blank lines in several files.
Use only one blank line between functions.
Add a blank line as a separator in a few places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operation can now fail, so change its return type to int.
Remove the inline wrapper while we're changing the signature.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently a higher priority client can remove a lower priority
client's filter with equal match-expression. This might happen if (a)
the higher priority client has a double-free bug, or (b) another
client with sufficient priority replaced and then removed an equal
filter, allowing the low priority client to insert an equal filter.
In neither case does it actually make sense to carry out the removal;
we should say the filter doesn't exist, as the filter currently
present is not the one that the high-priority client is referring to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Change all the 'stack' naming to 'auto' (or other meaningful term);
the device address list is based on more than just what the network
stack wants, and the no-match filters aren't really what the stack
wants at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MAC filters inserted automatically by the driver, based on the device
address list (EF10) or no-match filters (Siena), should be overridable
at MANUAL or REQUIRED priority. Currently they themselves have
REQUIRED priority and this requires some odd special-casing.
We also can't reliably tell whether such a MAC filter has or has
not been overridden. We just remember that it is wanted by the
stack (RX_STACK flag).
Add another priority level, AUTO, between HINT and MANUAL, and
use this for the automatic filters while they have not been
overridden. Remove the RX_STACK flag. Add an RX_OVER_AUTO
flag which is set only when an AUTO filter has been overridden
(or was requested to be inserted while a higher-priority filter
existed).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 implementation already does this, and it makes more logical
sense to group the RSS hash key and indirection table together.
Rename the operation to rx_push_rss_config.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Update the dates for files that have been added to in 2012-2013.
Drop the 'Solarstorm' brand name that's still lingering here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The TX path firmware for EF10 supports 'option descriptors' to control
offloads and various other features. Add a flag and field for these
in struct efx_tx_buffer, and don't treat them as DMA descriptors on
completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On EF10, the firmware will initiate a queue flush in certain
error cases. We need to accept that flush events might appear
at any time after a queue has been initialised, not just when
we try to flush them.
We can handle Falcon-architecture in just the same way.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Also, since we handle all DMA errors in the same way, merge
RESET_TYPE_(RX|TX)_DESC_FETCH into RESET_TYPE_DMA_ERROR.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On Falcon we implement MAC filtering requested by the stack using the
MAC wrapper's single unicast filter and multicast hash filter. Siena
is very similar, though MAC configuration is mediated by the MC.
Since MCDI operations may sleep, reconfiguration is deferred from
ndo_set_rx_mode to a work item. However, it still updates the private
variables describing the filter state synchronously. Contrary to
comments, the later use of these variables is not protected using the
address lock, resulting in race conditions.
Move the state update to a new function
efx_farch_filter_sync_rx_mode() and make the Falcon-arch MAC
configuration functions call that, so that its use is consistently
serialised by the mac_lock.
Invert and rename the promiscuous flag to the more accurate
unicast_filter, and comment that both this and multicast_hash are
not used on EF10.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MAC filters inserted on request from the stack (ndo_set_rx_mode)
should allow manual steering but not removal. Currently we have a
special case for Siena's all-multicast and all-unicast MAC filters,
but on EF10 we need to allow for steering of precise MAC filters as
well.
The EFX_FILTER_FLAG_RX_STACK flag changes the behaviour of replacement
and removal requests:
- Replacement *of* a filter with this flag never clears the flag but
does change steering and saved priority
- Replacement *by* a filter with this flag only sets the flag but does
not change steering
- Removal with priority < EFX_FILTER_PRI_REQUIRED really resets RX
steering and saved priority
This could support precise MAC filtering on Siena in future.
As a side-benefit, the default MAC filters are hidden from ethtool
until they are steered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the special case for removal of default filters from
efx_farch_filter_table_clear_entry() into a wrapper function,
efx_farch_filter_table_remove(). Move the existence and priority
checks into the latter and use it where appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Aside from accelerated RFS, there is almost nothing that can be shared
between the filter table implementations for the Falcon architecture
and EF10.
Move the few shared functions into efx.c and rx.c and the rest into
farch.c. Introduce efx_nic_type operations for the implementation and
inline wrapper functions that call these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The workarounds that currently use EFX_WORKAROUND_ALWAYS are in
Falcon-specific or Falcon-arch-specific code, so get rid of the
conditions altogether. Add/move comments as appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add efx_nic_type operations for the many efx_nic functions that need
to be implemented different on EF10. For now, change most of the
existing efx_nic_*() functions into inline wrappers. As a later step,
we may be able to improve branch prediction for operations used on the
fast path by copying the pointers into each queue/channel structure.
Move the Falcon/Siena implementations to new file farch.c and rename
the functions and static data to use a prefix of 'efx_farch_'.
Move efx_may_push_tx_desc() to nic.h, as the EF10 TX code will also
use it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
