The recent scan overhaul broke locking
because now we can jump to code that
attempts to unlock, while we don't have
the mutex held. Fix this by holding the
mutex around all the relevant code.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the NVS/INI-parameters for the driver/firmware there is the FEM
(front end module) selection option, which may configure the hardware FEM
via autodetection or manual selection. So far, there has been support for
manual selection only.
Add support for FEM autodetection.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 5ed3bc7288.
It turns-out that not all drivers are calling ieee80211_tx_status from a
compatible context. Revert this for now and try again later...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 030725d2c7.
This commit relies on commit 5ed3bc7288
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/scan.c: In function ‘ieee80211_scan_cancel’:
net/mac80211/scan.c:794: warning: ‘finish’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple interfaces are actively trying
to associate with the same BSS, they may both
find that the BSS isn't there and then try to
unlink it. This can cause errors since the
unlinking code can't currently deal with items
that have already been unlinked.
Normally this doesn't happen as most people
don't try to use multiple station interfaces
that associate at the same time too.
Fix this by using the list entry as a flag to
see if the item is still on a list.
Cc: stable@kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Hun-Kyi Wynn <hkwynn@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This information is already available in mac80211, we just need to export it
via cfg80211 and nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 7acc7c683a. It was
applied to avoid possible warning in ieee80211_restart_hw, however
reason of the warning were races in mac80211, currently hopefully fixed.
Not reseting device when performing scan is bad for two reasons.
When forcing reset from iwl_check_stuck_queue(), in case of fail,
reset will be repeated until scan finish. But since firmware is in bad
shape, scan only finish after scan_check work (about 7s). So we will
delay the reset, what is not good behaviour.
When forcing reset from iwl_recover_from_statistics(), we will not
repeat the reset, so we will not perform reset at all when needed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We nulify local->scan_req on failure in __ieee80211_start_scan, so
__ieee80211_scan_completed will not call cfg80211_scan_done. Fix that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When performing hw scan and not abort it, __ieee80211_scan_completed()
is currently called from scan work, so does not need to reschedule work
to call drv_hw_scan().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is partial revert and fix for commit
85f72bc839 "mac80211: only cancel
software-based scans on suspend"
When cfg80211 request the scan and mac80211 perform some management work,
we defer the scan request. We do not canceling such requests when calling
ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just
before the call. So fix that problem.
Another problem, which commit 85f72bc839
tries to solve, is we can not cancel HW scan. Hence patch make
ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping
local->mtx lock assures that the deferred scan will not become
"working" HW scan.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are taking local->mtx inside __ieee80211_scan_completed(), but just
before call to that function we drop the lock. Dropping/taking lock is not
good, because can lead to hard to understand race conditions.
Patch split scan_completed() code into two functions, first must be called
with local->mtx taken and second without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use goto instruction to call __ieee80211_scan_completed only ones in
ieee80211_scan_work. This is prepare for the next patch.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yikes! The error return keeps a netdev reference
and the rdev mutex locked, fix that!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drv_config callback is called only after the ack for the nullframe
is received and so driver need not do anything special for this.
So remove NULLFUNC_COMPLETED, PS_ENABLED flags and bf_isnullfunc
flags from ath9k as mac80211 already handles them properly.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the last rounds of cleanup, these functions are now functionally
equivalent and can thus be merged.
Also get rid of some excessive (and redundant) debug messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code gets more concise and readable when making the new ANI functions
fall back to the old ones if ANI v2 is disabled. This also makes further code
cleanup easier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse
it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old
and ath9k_hw_proc_mib_event_new).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI state is kept per channel, so instead of keeping an array of ANI states
with an arbitrary size of 255, move the ANI state into the channel struct.
Move some config settings that are not per-channel out of
the per-channel struct to save some memory.
With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can
be merged into a single function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.
Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never delete the addBA response timer, which
is typically fine, but if the station it belongs
to is deleted very quickly after starting the BA
session, before the peer had a chance to reply,
the timer may fire after the station struct has
been freed already. Therefore, we need to delete
the timer in a suitable spot -- best when the
session is being stopped (which will happen even
then) in which case the delete will be a no-op
most of the time.
I've reproduced the scenario and tested the fix.
This fixes the crash reported at
http://mid.gmane.org/4CAB6F96.6090701@candelatech.com
Cc: stable@kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing
commit 37e5bf6535
Author: Luis R. Rodriguez <lrodriguez@atheros.com>
Date: Sat Jun 12 00:33:40 2010 -0400
ath9k_hw: fix clock rate calculations for ANI
This commit accidentally broke clock rate calculation by doubling the
calculated clock rate
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
move paramater definitions to a device paramater structure only
leaving the device name, which antennas are used and what firmware
file to use in the iwl_cfg structure. this will not completely
remove the redundancies but greatly reduce them for devices that
only vary by name or antennas. the parameters that are more
likely to change within a given device family are left in iwl_cfg.
also separate bt param structure added to help reduce more.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Hardware scan is the prefer method for all iwlwifi devices;
especially for dual-mode functions. Schedule to deprecate the
software scan support in kernel 2.6.40
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Be consistent and use the wk->chan instead of the
local->hw.conf.channel for the association done work.
This prevents any possible races against channel changes
while we run this work.
In the case that the race did happen we would be initializing
the bit rates for the new AP under the assumption of a wrong
channel and in the worst case, wrong band. This could lead
to trying to assuming we could use CCK frames on 5 GHz, for
example.
This patch has a fix for kernels >= v2.6.34
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The documentation for NL80211_CMD_REMAIN_ON_CHANNEL
isn't accurate, an interface index is required by
the command. Update it accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base_eep_header_4k structure contains information that the
device supports high power tx gain table or not. However the
ath9k_hw_4k_get_eeprom function does not return that value when
it is called with EEP_TXGAIN_TYPE. This leads to that the tx gain
initialization will use the init values from the original tx gain
table even if the device inidicates that the high power table
should be used.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Shu Hwa Shen <shensh@zcomm.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should only wake up queues which mac80211 knows about (queues 0-3). We have
another internal queue ("CAB", queue number 6) which we use for power-saved
frames. When transmitted frames are processed from this queue, we have to make
sure we don't bother mac80211 with waking a queue it doesn't know about.
this fixes:
WARNING: at /home/br1/ath/wireless-testing/net/mac80211/util.c:275
__ieee80211_wake_queue+0xd6/0xe0 [mac80211]()
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate boilerplate code needed for .dumpit
calls operating on netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a new flag that requires the netdev to be
UP and use it to check instead of coding the
check into all functions that require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
