The Slave Page Response Timeout event indicates to the Host that a
slave page response timeout has occurred in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 110
"7.7.72 Slave Page Response Timeout Event [New Section]
...
Note: this event will be generated if the slave BR/EDR Controller
responds to a page but does not receive the master FHS packet
(see Baseband, Section 8.3.3) within pagerespTO.
Event Parameters: NONE"
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Synchronization Train Complete event indicates that the Start
Synchronization Train command has completed.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 103
"7.7.67 Synchronization Train Complete Event [New Section]
...
Event Parameters:
Status 0x00 Start Synchronization Train command completed
successfully.
0x01-0xFF Start Synchronization Train command failed.
See Part D, Error Codes, for error codes and
descriptions."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Start_Synchronization_Train command controls the Synchronization
Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 86
"7.1.51 Start Synchronization Train Command [New Section]
...
If connectionless slave broadcast mode is not enabled, the Command
Disallowed (0x0C) error code shall be returned. After receiving this
command and returning a Command Status event, the Baseband starts
attempting to send synchronization train packets containing information
related to the enabled Connectionless Slave Broadcast packet timing.
Note: The AFH_Channel_Map used in the synchronization train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
The synchronization train packets will be sent using the parameters
specified by the latest Write_Synchronization_Train_Parameters command.
The Synchronization Train will continue until synchronization_trainTO
slots (as specified in the last Write_Synchronization_Train command)
have passed or until the Host disables the Connectionless Slave Broadcast
logical transport."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
he Set_Connectionless_Slave_Broadcast command controls the
Connectionless Slave Broadcast functionality in the BR/EDR
Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 78
"7.1.49 Set Connectionless Slave Broadcast Command [New Section]
...
The LT_ADDR indicated in the Set_Connectionless_Slave_Broadcast shall be
pre-allocated using the HCI_Set_Reserved_LT_ADDR command. If the
LT_ADDR has not been reserved, the Unknown Connection Identifier (0x02)
error code shall be returned. If the controller is unable to reserve
sufficient bandwidth for the requested activity, the Connection Rejected
Due to Limited Resources (0x0D) error code shall be returned.
The LPO_Allowed parameter informs the BR/EDR Controller whether it is
allowed to sleep.
The Packet_Type parameter specifies which packet types are allowed. The
Host shall either enable BR packet types only, or shall enable EDR and DM1
packet types only.
The Interval_Min and Interval_Max parameters specify the range from which
the BR/EDR Controller must select the Connectionless Slave Broadcast
Interval. The selected Interval is returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Write_Synchronization_Train_Parameters command configures
the Synchronization Train functionality in the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 97
"7.3.90 Write Synchronization Train Parameters Command [New Section]
...
Note: The AFH_Channel_Map used in the Synchronization Train packets is
configured by the Set_AFH_Channel_Classification command and the local
channel classification in the BR/EDR Controller.
Interval_Min and Interval_Max specify the allowed range of
Sync_Train_Interval. Refer to [Vol. 2], Part B, section 2.7.2 for
a detailed description of Sync_Train_Interval. The BR/EDR Controller shall
select an interval from this range and return it in Sync_Train_Interval.
If the Controller is unable to select a value from this range, it shall
return the Invalid HCI Command Parameters (0x12) error code.
Once started (via the Start_Synchronization_Train Command) the
Synchronization Train will continue until synchronization_trainTO slots have
passed or Connectionless Slave Broadcast has been disabled."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set_Connectionless_Slave_Broadcast_Data command provides the
ability for the Host to set Connectionless Slave Broadcast data in
the BR/EDR Controller.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 93
"7.3.88 Set Connectionless Slave Broadcast Data Command [New Section]
...
If connectionless slave broadcast mode is disabled, this data shall be
kept by the BR/EDR Controller and used once connectionless slave broadcast
mode is enabled. If connectionless slave broadcast mode is enabled,
and this command is successful, this data will be sent starting with
the next Connectionless Slave Broadcast instant.
The Data_Length field may be zero, in which case no data needs to be
provided.
The Host may fragment the data using the Fragment field in the command. If
the combined length of the fragments exceeds the capacity of the largest
allowed packet size specified in the Set Connectionless Slave Broadcast
command, all fragments associated with the data being assembled shall be
discarded and the Invalid HCI Command Parameters error (0x12) shall be
returned."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Delete_Reserved_LT_ADDR command requests that the BR/EDR
Controller cancel the reservation for a specific LT_ADDR reserved for the
purposes of Connectionless Slave Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 92
"7.3.87 Delete Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is not reserved by the
BR/EDR Controller, it shall return the Unknown Connection Identifier (0x02)
error code.
If connectionless slave broadcast mode is still active, then the Controller
shall return the Command Disallowed (0x0C) error code."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Set_Reserved_LT_ADDR command allows the host to request that the
BR/EDR Controller reserve a specific LT_ADDR for Connectionless Slave
Broadcast.
The Core Spec Addendum 4 adds this command in part B Connectionless
Slave Broadcast.
Bluetooth Core Specification Addendum 4 - Page 90
"7.3.86 Set Reserved LT_ADDR Command [New Section]
...
If the LT_ADDR indicated in the LT_ADDR parameter is already in use by the
BR/EDR Controller, it shall return the ACL Connection Already Exists (0x0B)
error code. If the LT_ADDR indicated in the LT_ADDR parameter is out of
range, the controller shall return the Invalid HCI Command Parameters (0x12)
error code. If the command succeeds, then the reserved LT_ADDR shall be
used when issuing subsequent Set Connectionless Slave Broadcast Data and
Set Connectionless Slave Broadcast commands.
To ensure that the reserved LT_ADDR is not already allocated, it is
recommended that this command be issued at some point after HCI_Reset is
issued but before page scanning is enabled or paging is initiated."
Signed-off-by: Dohyun Pyun <dh79.pyun@samsung.com>
Signed-off-by: C S Bhargava <cs.bhargava@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On dual-mode BR/EDR/LE and LE only controllers it is possible
to configure a random address. There are two types or random
addresses, one is static and the other private. Since the
random private addresses require special privacy feature to
be supported, the configuration of these two are kept separate.
This command allows for setting the static random address. It is
only supported on controllers with LE support. The static random
address is suppose to be valid for the lifetime of the controller
or at least until the next power cycle. To ensure such behavior,
setting of the address is limited to when the controller is
powered off.
The special BDADDR_ANY address (00:00:00:00:00:00) can be used to
disable the static address. This is also the default value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces a new mgmt command for enabling/disabling BR/EDR
functionality. This can be convenient when one wants to make a dual-mode
controller behave like a single-mode one. The command is only available
for dual-mode controllers and requires that LE is enabled before using
it. The BR/EDR setting can be enabled at any point, however disabling it
requires the controller to be powered off (otherwise a "rejected"
response will be sent).
Disabling the BR/EDR setting will automatically disable all other BR/EDR
related settings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To allow treating dual-mode (BR/EDR/LE) controllers as single-mode ones
(LE-only) we want to introduce a new HCI_BREDR_ENABLED flag to track
whether BR/EDR is enabled or not (previously we simply looked at the
feature bit with lmp_bredr_enabled).
This patch add the new flag and updates the relevant places to test
against it instead of using lmp_bredr_enabled. The flag is by default
enabled when registering an adapter and only cleared if necessary once
the local features have been read during the HCI init procedure.
We cannot completely block BR/EDR usage in case user space uses raw HCI
sockets but the patch tries to block this in places where possible, such
as the various BR/EDR specific ioctls.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.
This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BDADDR_LOCAL is a relict from userspace and has never been used
within the kernel. So remove that constant and replace it with a new
BDADDR_NONE that is similar to HCI_DEV_NONE with all bits set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a new mgmt command for enabling and disabling
LE advertising. The command depends on the LE setting being enabled
first and will return a "rejected" response otherwise. The patch also
adds safeguards so that there will ever only be one set_le or
set_advertising command pending per adapter.
The response handling and new_settings event sending is done in an
asynchronous request callback, meaning raw HCI access from user space to
enable advertising (e.g. hciconfig leadv) will not trigger the
new_settings event. This is intentional since trying to support mixed
raw HCI and mgmt access would mean adding extra state tracking or new
helper functions, essentially negating the benefit of using the
asynchronous request framework. The HCI_LE_ENABLED and HCI_LE_PERIPHERAL
flags however are updated correctly even with raw HCI access so this
will not completely break subsequent access over mgmt.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds a new mgmt setting for LE advertising and hooks up the
necessary places in the mgmt code to operate on the HCI_LE_PERIPHERAL
flag (which corresponds to this setting). This patch does not yet add
any new command for enabling the setting - that is left for a subsequent
patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch updates the code to use an asynchronous request for handling
the enabling and disabling of LE support. This refactoring is necessary
as a preparation for adding advertising support, since when LE is
disabled we should also disable advertising, and the cleanest way to do
this is to perform the two respective HCI commands in the same
asynchronous request.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
For those controller that support the HCI_Set_Event_Mask_Page_2 command
we should include it in the init sequence. This patch implements sending
of the command and enables the events in it based on supported features
(currently only CSB is checked).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds support for reading the synchronization train parameters
for controllers that support the feature. Since the feature is
detectable through the local features page 2, which is retreived only in
stage 3 of the HCI init sequence, there is no other option than to add a
fourth stage to the init sequence.
For now the patch doesn't yet add storing of the parameters, but it is
nevertheless convenient to have around to see what kind of parameters
various controllers use by default (analyzable e.g. with the btmon user
space tool).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In the case of blocking sockets we should not proceed with sendmsg() if
the socket has the BT_SK_SUSPEND flag set. So far the code was only
ensuring that POLLOUT doesn't get set for non-blocking sockets using
poll() but there was no code in place to ensure that blocking sockets do
the right thing when writing to them.
This patch adds a new bt_sock_wait_ready helper function to sleep in the
sendmsg call if the BT_SK_SUSPEND flag is set, and wake up as soon as it
is unset. It also updates the L2CAP and RFCOMM sendmsg callbacks to take
advantage of this new helper function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The struct for HCI_Set_Event_Mask is never used. Instead a local 8-byte
array is used for sending this command. Therefore, remove the
unnecessary struct definition.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introcuces a new HCI socket channel that allows user
applications to take control over a specific HCI device. The application
gains exclusive access to this device and forces the kernel to stay away
and not manage it. In case of the management interface it will actually
hide the device.
Such operation is useful for security testing tools that need to operate
underneath the Bluetooth stack and need full control over a device. The
advantage here is that the kernel still provides the service of hardware
abstraction and HCI level access. The use of Bluetooth drivers for
hardware access also means that sniffing tools like btmon or hcidump
are still working and the whole set of transaction can be traced with
existing tools.
With the new channel it is possible to send HCI commands, ACL and SCO
data packets and receive HCI events, ACL and SCO packets from the
device. The format follows the well established H:4 protocol.
The new HCI user channel can only be established when a device has been
through its setup routine and is currently powered down. This is
enforced to not cause any problems with current operations. In addition
only one user channel per HCI device is allowed. It is exclusive access
for one user application. Access to this channel is limited to process
with CAP_NET_RAW capability.
Using this new facility does not require any external library or special
ioctl or socket filters. Just create the socket and bind it. After that
the file descriptor is ready to speak H:4 protocol.
struct sockaddr_hci addr;
int fd;
fd = socket(AF_BLUETOOTH, SOCK_RAW, BTPROTO_HCI);
memset(&addr, 0, sizeof(addr));
addr.hci_family = AF_BLUETOOTH;
addr.hci_dev = 0;
addr.hci_channel = HCI_CHANNEL_USER;
bind(fd, (struct sockaddr *) &addr, sizeof(addr));
The example shows on how to create a user channel for hci0 device. Error
handling has been left out of the example. However with the limitations
mentioned above it is advised to handle errors. Binding of the user
cahnnel socket can fail for various reasons. Specifically if the device
is currently activated by BlueZ or if the access permissions are not
present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch introduces a new user channel flag that allows to give full
control of a HCI device to a user application. The kernel will stay away
from the device and does not allow any further modifications of the
device states.
The existing raw flag is not used since it has a bit of unclear meaning
due to its legacy. Using a new flag makes the code clearer.
A device with the user channel flag set can still be enumerate using the
legacy API, but it does not longer enumerate using the new management
interface used by BlueZ 5 and beyond. This is intentional to not confuse
users of modern systems.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The only actual current lockref user (dcache) uses zero reference counts
even for perfectly live dentries, because it's a cache: there may not be
any users, but that doesn't mean that we want to throw away the dentry.
At the same time, the dentry cache does have a notion of a truly "dead"
dentry that we must not even increment the reference count of, because
we have pruned it and it is not valid.
Currently that distinction is not visible in the lockref itself, and the
dentry cache validation uses "lockref_get_or_lock()" to either get a new
reference to a dentry that already had existing references (and thus
cannot be dead), or get the dentry lock so that we can then verify the
dentry and increment the reference count under the lock if that
verification was successful.
That's all somewhat complicated.
This adds the concept of being "dead" to the lockref itself, by simply
using a count that is negative. This allows a usage scenario where we
can increment the refcount of a dentry without having to validate it,
and pushing the special "we killed it" case into the lockref code.
The dentry code itself doesn't actually use this yet, and it's probably
too late in the merge window to do that code (the dentry_kill() code
with its "should I decrement the count" logic really is pretty complex
code), but let's introduce the concept at the lockref level now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile 2 (of many) from Al Viro:
"Mostly Miklos' series this time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify dcache.c inlined helpers where possible
fuse: drop dentry on failed revalidate
fuse: clean up return in fuse_dentry_revalidate()
fuse: use d_materialise_unique()
sysfs: use check_submounts_and_drop()
nfs: use check_submounts_and_drop()
gfs2: use check_submounts_and_drop()
afs: use check_submounts_and_drop()
vfs: check unlinked ancestors before mount
vfs: check submounts and drop atomically
vfs: add d_walk()
vfs: restructure d_genocide()
Pull namespace changes from Eric Biederman:
"This is an assorted mishmash of small cleanups, enhancements and bug
fixes.
The major theme is user namespace mount restrictions. nsown_capable
is killed as it encourages not thinking about details that need to be
considered. A very hard to hit pid namespace exiting bug was finally
tracked and fixed. A couple of cleanups to the basic namespace
infrastructure.
Finally there is an enhancement that makes per user namespace
capabilities usable as capabilities, and an enhancement that allows
the per userns root to nice other processes in the user namespace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Kill nsown_capable it makes the wrong thing easy
capabilities: allow nice if we are privileged
pidns: Don't have unshare(CLONE_NEWPID) imply CLONE_THREAD
userns: Allow PR_CAPBSET_DROP in a user namespace.
namespaces: Simplify copy_namespaces so it is clear what is going on.
pidns: Fix hang in zap_pid_ns_processes by sending a potentially extra wakeup
sysfs: Restrict mounting sysfs
userns: Better restrictions on when proc and sysfs can be mounted
vfs: Don't copy mount bind mounts of /proc/<pid>/ns/mnt between namespaces
kernel/nsproxy.c: Improving a snippet of code.
proc: Restrict mounting the proc filesystem
vfs: Lock in place mounts from more privileged users
Pull security subsystem updates from James Morris:
"Nothing major for this kernel, just maintenance updates"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
apparmor: add the ability to report a sha1 hash of loaded policy
apparmor: export set of capabilities supported by the apparmor module
apparmor: add the profile introspection file to interface
apparmor: add an optional profile attachment string for profiles
apparmor: add interface files for profiles and namespaces
apparmor: allow setting any profile into the unconfined state
apparmor: make free_profile available outside of policy.c
apparmor: rework namespace free path
apparmor: update how unconfined is handled
apparmor: change how profile replacement update is done
apparmor: convert profile lists to RCU based locking
apparmor: provide base for multiple profiles to be replaced at once
apparmor: add a features/policy dir to interface
apparmor: enable users to query whether apparmor is enabled
apparmor: remove minimum size check for vmalloc()
Smack: parse multiple rules per write to load2, up to PAGE_SIZE-1 bytes
Smack: network label match fix
security: smack: add a hash table to quicken smk_find_entry()
security: smack: fix memleak in smk_write_rules_list()
xattr: Constify ->name member of "struct xattr".
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
- Handle unaligned lengths in omap-aes.
- Added SHA384/SHA512 to omap-sham.
- Added OMAP5/AM43XX SHAM support.
- Added OMAP4 TRNG support.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
hwrng: via - Add MODULE_DEVICE_TABLE
crypto: fcrypt - Fix bitoperation for compilation with clang
crypto: nx - fix SHA-2 for chunks bigger than block size
crypto: nx - fix GCM for zero length messages
crypto: nx - fix XCBC for zero length messages
crypto: nx - fix limits to sg lists for AES-CCM
crypto: nx - fix limits to sg lists for AES-XCBC
crypto: nx - fix limits to sg lists for AES-GCM
crypto: nx - fix limits to sg lists for AES-CTR
crypto: nx - fix limits to sg lists for AES-CBC
crypto: nx - fix limits to sg lists for AES-ECB
crypto: nx - add offset to nx_build_sg_lists()
padata - Register hotcpu notifier after initialization
padata - share code between CPU_ONLINE and CPU_DOWN_FAILED, same to CPU_DOWN_PREPARE and CPU_UP_CANCELED
hwrng: omap - reorder OMAP TRNG driver code
crypto: omap-sham - correct dma burst size
crypto: omap-sham - Enable Polling mode if DMA fails
crypto: tegra-aes - bitwise vs logical and
crypto: sahara - checking the wrong variable
...
Pull networking fixes from David Miller:
"A quick set of fixes, some to deal with fallout from yesterday's
net-next merge.
1) Fix compilation of bnx2x driver with CONFIG_BNX2X_SRIOV disabled,
from Dmitry Kravkov.
2) Fix a bnx2x regression caused by one of Dave Jones's mistaken
braces changes, from Eilon Greenstein.
3) Add some protective filtering in the netlink tap code, from Daniel
Borkmann.
4) Fix TCP congestion window growth regression after timeouts, from
Yuchung Cheng.
5) Correctly adjust TCP's rcv_ssthresh for out of order packets, from
Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tcp: properly increase rcv_ssthresh for ofo packets
net: add documentation for BQL helpers
mlx5: remove unused MLX5_DEBUG param in Kconfig
bnx2x: Restore a call to config_init
bnx2x: fix broken compilation with CONFIG_BNX2X_SRIOV is not set
tcp: fix no cwnd growth after timeout
net: netlink: filter particular protocols from analyzers
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block.
This is found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on
some x86 boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the
modernized pin control driver to provide GPIO for the
modern platforms instead.
- The usual bunch of non-critical fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSKZvzAAoJEEEQszewGV1zUg8QAMAqM90/U/0c73fxS28BbN6+
5bO3a/l9JZYWHyk+739oFZqMUoPDKcq/IOSbirxdgpWE3zcF34ogNfIgSoAL77C5
3yGa2Lclkxmngo8ZXXeu6DSTq82rlaVjCcHcXw/qd6lVAZT8YaS364vGYpcENPxI
s1yfrCZy89kZQufX++ytcbIUj75KXHvd9MK9IRE4BVkQMgLXAX/oSbTdB5PhFb79
J5ls0T1c8JRxI4sj32ZDh6dfeKGsRQF20z6OO5o0ZIyQ+ZGLJPlYatdivJelQz9J
P67suwn86RXfABISYle2YbNmy3zX+wEyG2nHASDL7hSfWtGpZ5ANJTXqrKjwFITL
sfqQhMtHDZ7fNbgA0kOyE25kgLybsJZNxR/PJGEHteT1+XZHi2nsP2NTNuxxEKjb
6NyLXrYXb0VK/poG+ZYXH2tt0C02pg3MfN9y+nfh8reG2bfeLvL/cU7DiQgMUGEf
DXwgXQdgow9dHus/ZuCuWz4xqAfqk5VRS8ba6Wg2F8uLaXY1qYM6mNeatzTfP3fg
5jALMy038l7yMBMFnTp8GCb78/iIXWLtEejtgoowBuGbZtOjii8wEExHvl4tCabQ
PbB9pG8+ojjiQPk2t1ZFFUqX6hCGBFrJbYnJj2vfftBHiFnz5bKrcSBOWVdTWgco
YqURqegvZVin4aQNGFF2
=oEK9
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.12 series:
- A new driver for the TZ1090 PDC which is used on the metag
architecture.
- A new driver for the Kontron ETX or COMexpress GPIO block. This is
found on some ETX x86 devices.
- A new driver for the Fintek Super-I/O chips, used on some x86
boards.
- Added device tree probing on a few select GPIO blocks.
- Drop the Exynos support from the Samsung GPIO driver.
The Samsung maintainers have moved over to use the modernized pin
control driver to provide GPIO for the modern platforms instead.
- The usual bunch of non-critical fixes and cleanups"
* tag 'gpio-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (36 commits)
gpio: return -ENOTSUPP if debounce cannot be set
gpio: improve error path in gpiolib
gpio: add GPIO support for F71882FG and F71889F
of: add vendor prefix for Microchip Technology Inc
gpio: mcp23s08: rename the device tree property
gpio: samsung: Drop support for Exynos SoCs
gpio: pcf857x: Remove pdata argument to pcf857x_irq_domain_init()
gpio: pcf857x: Sort headers alphabetically
gpio: max7301: Reverting "Do not force SPI speed when using OF Platform"
gpio: Fix bit masking in Kontron PLD GPIO driver
gpio: pca953x: fix gpio input on gpio offsets >= 8
drivers/gpio: simplify use of devm_ioremap_resource
drivers/gpio/gpio-omap.c: convert comma to semicolon
gpio-lynxpoint: Fix warning about unbalanced pm_runtime_enable
gpio: Fix platform driver name in Kontron PLD GPIO driver
gpio: adnp: Fix segfault if request_threaded_irq fails
gpio: msm: Staticize local variable 'msm_gpio'
gpio: gpiolib-of.c: make error message more meaningful by adding the node name and index
gpio: use dev_get_platdata()
gpio/mxc: add chained_irq_enter/exit() to mx2_gpio_irq_handler
...
Pull input updates from Dmitry Torokhov:
"A new driver for slidebar on Ideapad laptops and a bunch of assorted
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: add SYN_MAX and SYN_CNT constants
Input: max11801_ts - convert to devm
Input: egalax-ts - fix typo and improve text
Input: MAINTAINERS - change maintainer for cyttsp driver
Input: cyttsp4 - kill 'defined but not used' compiler warnings
Input: add driver for slidebar on Lenovo IdeaPad laptops
Input: omap-keypad - set up irq type from DT
Input: omap-keypad - enable wakeup capability for keypad.
Input: omap-keypad - clear interrupts on open
Input: omap-keypad - convert to threaded IRQ
Input: omap-keypad - use bitfiled instead of hardcoded values
Input: cyttsp4 - remove useless NULL test from cyttsp4_watchdog_timer()
Input: wacom - fix error return code in wacom_probe()
Input: as5011 - fix error return code in as5011_probe()
Input: keyboard, serio - simplify use of devm_ioremap_resource
Input: tegra-kbc - simplify use of devm_ioremap_resource
Input: htcpen - fix incorrect placement of __initdata
Input: qt1070 - add power management ops
Input: wistron_btns - add MODULE_DEVICE_TABLE
Input: wistron_btns - mark the Medion MD96500 keymap as tested
...
This reverts commits 61e00655e9, 73f8645db1 and 8e22ecb603:
"Input: introduce BTN/ABS bits for drums and guitars"
"HID: wiimote: add support for Guitar-Hero drums"
"HID: wiimote: add support for Guitar-Hero guitars"
The extra new ABS_xx values resulted in ABS_MAX no longer being a
power-of-two, which broke the comparison logic. It also caused the
ioctl numbers to overflow into the next byte, causing problems for that.
We'll try again for 3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch reinstates commits
67822649d739761214ee0b95a7f85731d939625a2d31e518a4
Now that module softdeps are in the kernel we can use that to resolve
the boot issue which cause the revert.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
Provide a kernel-doc comment documentation for the BQL helpers:
- netdev_sent_queue
- netdev_completed_queue
- netdev_reset_queue
Similarly to how it is done for the other functions, the documentation
only covers the function operating on struct net_device and not struct
netdev_queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
ignored by the CPU).
- Kernel mode NEON (no users for arm64 yet but work in progress).
- arm64 kernel Image header extended to accommodate future EFI stub.
- Remove BogoMIPS reporting (not relevant, it's just the timer
frequency).
- Clean-up (EM_AARCH64/EM_ARM to elf-em.h, ELF notes in read-only
segment, unused variable).
- Bug-fixes (RAM boundaries not 2MB aligned, perf, includes).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=5w0G
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 update from Catalin Marinas:
- User tagged pointers support (top 8-bit of user pointers
automatically ignored by the CPU).
- Kernel mode NEON (no users for arm64 yet but work in progress).
- arm64 kernel Image header extended to accommodate future EFI stub.
- Remove BogoMIPS reporting (not relevant, it's just the timer
frequency).
- Clean-up (EM_AARCH64/EM_ARM to elf-em.h, ELF notes in read-only
segment, unused variable).
- Bug-fixes (RAM boundaries not 2MB aligned, perf, includes).
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
Documentation/arm64: clarify requirements for DTB placement
arm64: mm: permit use of tagged pointers at EL0
Move the EM_ARM and EM_AARCH64 definitions to uapi/linux/elf-em.h
arm64: Remove unused cpu_name ascii in arch/arm64/mm/proc.S
arm64: delay: don't bother reporting bogomips in /proc/cpuinfo
arm64: Fix mapping of memory banks not ending on a PMD_SIZE boundary
arm64: move elf notes into readonly segment
arm64: Enable interrupts in the EL0 undef handler
arm64: Expand arm64 image header
ARM64: include: asm: include "asm/types.h" in "pgtable-2level-types.h" and "pgtable-3level-types.h"
arm64: add support for kernel mode NEON
arm64: perf: fix ARMv8 EVTYPE_MASK to include NSH bit
arm64: perf: fix group validation when using enable_on_exec
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Pull HID updates from Jiri Kosina:
"Highlights:
- conversion of HID subsystem to use devm-based resource management,
from Benjamin Tissoires
- i2c-hid support for DT bindings, from Benjamin Tissoires
- much improved support for Win8-multitouch devices, from Benjamin
Tissoires
- cleanup of core code using common hidinput_input_event(), from
David Herrmann
- fix for bug in implement() access to the bit stream (causing oops)
that has been present in the code for ages, but devices that are
able to trigger it have started to appear only now, from Jiri
Kosina
- fixes for CVE-2013-2899, CVE-2013-2898, CVE-2013-2896,
CVE-2013-2892, CVE-2013-2888 (all triggerable only by specially
crafted malicious HW devices plugged into the system), from Kees
Cook
- hidraw oops fix, from Manoj Chourasia
- various smaller fixes here and there, support for a bunch of new
devices by various contributors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (53 commits)
HID: MAINTAINERS: add roccat drivers
HID: hid-sensor-hub: change kmalloc + memcpy by kmemdup
HID: hid-sensor-hub: move to devm_kzalloc
HID: hid-sensor-hub: fix indentation accross the code
HID: move HID_REPORT_TYPES closer to the report-definitions
HID: check for NULL field when setting values
HID: picolcd_core: validate output report details
HID: sensor-hub: validate feature report details
HID: ntrig: validate feature report details
HID: pantherlord: validate output report details
HID: hid-wiimote: print small buffers via %*phC
HID: uhid: improve uhid example client
HID: Correct the USB IDs for the new Macbook Air 6
HID: wiimote: add support for Guitar-Hero guitars
HID: wiimote: add support for Guitar-Hero drums
Input: introduce BTN/ABS bits for drums and guitars
HID: battery: don't do DMA from stack
HID: roccat: add support for KonePureOptical v2
HID: picolcd: Prevent NULL pointer dereference on _remove()
HID: usbhid: quirk for N-Trig DuoSense Touch Screen
...
Pull ext3, reiserfs, udf & isofs fixes from Jan Kara:
"The contains a bunch of ext3 cleanups and minor improvements, major
reiserfs locking changes which should hopefully fix deadlocks
introduced by BKL removal, and udf/isofs changes to refuse mounting fs
rw instead of mounting it ro automatically which makes eject button
work as expected for all media (see the changelog for why userspace
should be ok with this change)"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
jbd: use a single printk for jbd_debug()
reiserfs: locking, release lock around quota operations
reiserfs: locking, handle nested locks properly
reiserfs: locking, push write lock out of xattr code
jbd: relocate assert after state lock in journal_commit_transaction()
udf: Refuse RW mount of the filesystem instead of making it RO
udf: Standardize return values in mount sequence
isofs: Refuse RW mount of the filesystem instead of making it RO
ext3: allow specifying external journal by pathname mount option
jbd: remove unneeded semicolon
This patch-set includes the following major enhancement patches.
o support inline xattrs
o add sysfs support to control GCs explicitly
o add proc entry to show the current segment usage information
o improve the GC/SSR performance
The other bug fixes are as follows.
o avoid the overflow on status calculation
o fix some error handling routines
o fix inconsistent xattr states after power-off-recovery
o fix incorrect xattr node offset definition
o fix deadlock condition in fsync
o fix the fdatasync routine for power-off-recovery
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YMk3
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches:
- support inline xattrs
- add sysfs support to control GCs explicitly
- add proc entry to show the current segment usage information
- improve the GC/SSR performance
The other bug fixes are as follows:
- avoid the overflow on status calculation
- fix some error handling routines
- fix inconsistent xattr states after power-off-recovery
- fix incorrect xattr node offset definition
- fix deadlock condition in fsync
- fix the fdatasync routine for power-off-recovery"
* tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (40 commits)
f2fs: optimize gc for better performance
f2fs: merge more bios of node block writes
f2fs: avoid an overflow during utilization calculation
f2fs: trigger GC when there are prefree segments
f2fs: use strncasecmp() simplify the string comparison
f2fs: fix omitting to update inode page
f2fs: support the inline xattrs
f2fs: add the truncate_xattr_node function
f2fs: introduce __find_xattr for readability
f2fs: reserve the xattr space dynamically
f2fs: add flags for inline xattrs
f2fs: fix error return code in init_f2fs_fs()
f2fs: fix wrong BUG_ON condition
f2fs: fix memory leak when init f2fs filesystem fail
f2fs: fix a compound statement label error
f2fs: avoid writing inode redundantly when creating a file
f2fs: alloc_page() doesn't return an ERR_PTR
f2fs: should cover i_xattr_nid with its xattr node page lock
f2fs: check the free space first in new_node_page
f2fs: clean up the needless end 'return' of void function
...
Pull ARM updates from Russell King:
"This set includes adding support for Neon acceleration of RAID6 XOR
code from Ard Biesheuvel, cache flushing and barrier updates from Will
Deacon, and a cleanup to the ARM debug code which reduces the amount
of code by about 500 lines.
A few other cleanups, such as constifying the machine descriptors
which already shouldn't be written to, cleaning up the printing of the
L2 cache size"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (55 commits)
ARM: 7826/1: debug: support debug ll on hisilicon soc
ARM: 7830/1: delay: don't bother reporting bogomips in /proc/cpuinfo
ARM: 7829/1: Add ".text.unlikely" and ".text.hot" to arm unwind tables
ARM: 7828/1: ARMv7-M: implement restart routine common to all v7-M machines
ARM: 7827/1: highbank: fix debug uart virtual address for LPAE
ARM: 7823/1: errata: workaround Cortex-A15 erratum 773022
ARM: 7806/1: allow DEBUG_UNCOMPRESS for Tegra
ARM: 7793/1: debug: use generic option for ep93xx PL10x debug port
ARM: debug: move SPEAr debug to generic PL01x code
ARM: debug: move davinci debug to generic 8250 code
ARM: debug: move keystone debug to generic 8250 code
ARM: debug: remove DEBUG_ROCKCHIP_UART
ARM: debug: provide generic option choices for 8250 and PL01x ports
ARM: debug: move PL01X debug include into arch/arm/include/debug/
ARM: debug: provide PL01x debug uart phys/virt address configuration options
ARM: debug: add support for word accesses to debug/8250.S
ARM: debug: move 8250 debug include into arch/arm/include/debug/
ARM: debug: provide 8250 debug uart phys/virt address configuration options
ARM: debug: provide 8250 debug uart register shift configuration option
ARM: debug: provide 8250 debug uart flow control configuration option
...
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
