The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL port E handling was added in
commit 26951caf55
Author: Xiong Zhang <xiong.y.zhang@intel.com>
Date: Mon Aug 17 15:55:50 2015 +0800
drm/i915/skl: enable DDI-E hotplug
but the whole function was moved in a another branch in
commit b93433ccf6
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Aug 20 10:47:36 2015 +0300
drm/i915: move ibx_digital_port_connected to intel_dp.c
and the addition was lost at some backmerge that I was unable to
identify. Put it back in.
Tested-by: Tomi Sarvela <tomix.p.sarvela@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Using intel_encoder's hpd_pin to check the live status
because of BXT A0/A1 WA for HPD pins and hpd_pin contains the
updated pin for the corresponding port.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
TPS3 is mandatory for downstream devices that support HBR2, and Intel
platforms that support HBR2 also support TPS3. Whenever TPS3 is
supported by both the source and sink, it should be used. In other
words, whenever the source and sink are capable of 5.4 Gbps link, we
should anyway go for TPS3, regardless of the link rate being selected.
Log an error if the sink has advertized HBR2 capability without TPS3
capability.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to have a separate flag for tps3 as the information is
only used at one location. Move the logic there to make it easier to
follow.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we release the lane soft reset before lane stagger settings
have been programmed. I believe that means we don't actually do lane
staggering. So move the soft reset deassert to happen after lane
staggering has been programmed.
The one confusing thing in this is that when we remove the power down
override from the lanes, they power up with defaul register values,
which do not have the soft reset overrides enabled. And according to
some docs by default the data lane resets are tied to cmnreset. So that
would mean that lanes would come out of reset without staggering as
soon as the power down overrides are removed. But since we can't access
either the lane stagger register nor the soft reset override registers
until the lanes are powered on, we can't really do anything about it.
So let's just set the soft reset overrides as soon as the lane is
powered on and hope for the best.
v2: Fix typos in commit message (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP MST encoder config function never sets ddi_pll_sel, even though
its value is programmed in its ->pre_enable() hook. That used to work
because a new pipe_config was kzalloc'ed at every modeset, and the value
of zero selects the highest clock for the PLL. Starting with the commit
below, the value of ddi_pll_sel is preserved through modesets, and since
the correct value wasn't properly setup by the MST code, it could lead
to warnings and blank screens.
commit 8504c74c7a
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 11:51:50 2015 +0300
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91628
Cc: stable@vger.kernel.org # 7e6313a251 drm/i915: Don't use link_bw for PLL setup
Cc: stable@vger.kernel.org
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/intel_dp_tps/drm_dp_tps/.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.
v2: Fix typo in commit message (Sivakumar)
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from future.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Enable eDP on DDI-E.
Also let's remove duplicated definitions to avoid later confusion.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We are no longer checkling the DP link status on long hpd. We used to do
that from the .hot_plug() handler, but it was removed when MST got
introduced.
If there's no userspace we now fail to retrain the link if the sink
power is toggled (or cable yanked and replugged), meaning the user is
left staring at a blank screen. With the retraining put back that should
be fixed.
Also remove the leftover comment that referred to the old retraining
from .hot_plug().
Fixes a regression introduced in:
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89453
Tested-by: Palmer Dabbelt <palmer@dabbelt.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91407
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89461
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89594
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85641
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With DPIO powergating active the DPLL can't be accessed unless
something else is keeping the common lane in the channel on.
That means the PPS kick procedure could fail to enable the PLL.
Power up some data lanes to force the common lane to power up
so that the PLL can be enabled temporarily.
v2: Avoid gcc uninitilized variable warning
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT platform uses live status bits from 0x44440 register to obtain DP
status on hotplug. The existing g4x_digital_port_connected() uses a
different register and hence misses DP hotplug events on BXT
platform. This patch fixes it by using the appropriate register(0x44440)
and live status bits(3:5).
Based on a patch by Durgadoss R <durgadoss.r@intel.com>, from whom the
commit message is shamelessly copy pasted.
Reported-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Choose the right function at the intel_digital_port_connected level.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Choose the right function at the intel_digital_port_connected level.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a common intel_digital_port_connected() that splits out to functions
for different platforms. No functional changes.
v2: make the function return a boolean
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the case added for eDP on port A (always connected from this
function's point of view), we should not be hitting any of the default
cases in ibx_digital_port_connected, so add MISSING_CASE annotation.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should not be hitting any of the default cases in
g4x_digital_port_connected, so add MISSING_CASE annotation and return
boolean status. The current behaviour is just cargo culting from the
days of yonder when the display port support was added to i915.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can be made static there. No functional changes.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs give you the impression that the unique transition scale
value shouldn't matter when unique transition scale is enabled. But
as Imre found on BXT (and I verfied also on BSW) the value does
matter. So from now on just program the same value 0x9a always.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch fixes the bug that SKL SKUs before B0 might return
HBR2 as supported even though it is not supposed to be enabled
on such platforms.
v2: optimize if else condition (Jani)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[Jani: minor whitespace fix.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV2pUkAAoJEHm+PkMAQRiGCIoH/Rb29ZjdCoZJp9OtnjAG+qRc
bG3YuomIdib86x7xHRKKaLWBa7din7IYjuwT/X4S4duO5a1R5Lp1sRG3IlGfhT0W
nBNbjFl4q4bOyiTPtTRTYyh4g5UQv4IuyCnCmZyCTJyVi/O6HVM9TWKUzm68P2dJ
30LwLUcQJ+mHueGJwFBAXe2BaojEpvYCdSX6tvbrQ/8X3FrVExZXuJl4uMYNFYNK
ZwG/v5t7tYOiAe76JGbrEuVFPZWLPEW7amHOWR0T4Ye4nWTlBgx7fENiNRlfgcvI
CM16l/xkyrZQ3Q5jZy1qYDfdHYF++dyEDysX4w1ae/X0aaLZn7l+u5VQD6WpkQQ=
=IF6I
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc8' into drm-next
Linux 4.2-rc8
Backmerge required for Intel so they can fix their -next tree up properly.
This patch removes TP3 support on CHV since there is no support
for HBR2 on this platform.
v2: rename the function to indicate it checks source rates (Jani)
v3: update comment to indicate TP3 dependency on HBR2 supported
hardware (Jani)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[Jani: fixed a couple of checkpatch warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch removes 5.4Gbps from supported link rate for CHV since
it is not supported in it.
v2: change the ordering for better readability (Ville)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts
commit fe51bfb95c.
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Mar 12 17:10:38 2015 +0200
CHV does not support intermediate frequencies so reverting the
patch that added it in the first place
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We only need the link_bw/rate_select parameters when starting link
training, and they should be computed based on the currently active
config, so throw them out from intel_dp and just compute on demand.
Toss in an extra debug print to see rate_select in addition to link_bw,
as the latter may be 0 for eDP 1.4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp->link_bw is going away, so consul the port_clock instead when
choosing between TP1 and TP3.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use a separate variable for the TRANS_DP_CTL value instead of reusing
'tmp' that otherwise contains the DP port register value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.
v2: Fix typo in commit message (Sivakumar)
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().
There should be no functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
DDIA HPD pin in place of DDIB.
v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
Added hpd_pin swapping for intel_dp_init_connector, setting encoder
for PORT_A as per the WA in irq_port (Imre)
v4: Dont enable interrupt for edp, also reframe the description (Siva)
v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
instead avoid setting hpd_pin itself (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 spec TEST_CRC_COUNT is a "4 bit wrap counter which
increments each time the TEST_CRC_x_x are updated."
However if we are trying to verify the screen hasn't changed we get
same (count, crc) pair twice. Without this patch we would return
-ETIMEOUT in this case.
So, if in 6 vblanks the pair (count, crc) hasn't changed we
return it anyway instead of returning error and let test case decide
if it was right or not.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."
However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.
So we face cases like this:
first get_sink_crc operation:
count: 0, crc: 000000000000
count: 1, crc: c101c101c101
returned expected crc: c101c101c101
secont get_sink_crc operation:
count: 1, crc: c101c101c101
count: 0, crc: 000000000000
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
But also the reset to 0 should be faster resulting into:
get_sink_crc operation:
count: 1, crc: c101c101c101
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).
If the pair changed you have your valid CRC.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.
But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BPP bits defined in VBT should be used only on panels whose
edid version is 1.3 or older. EDID version 1.4 introduced offsets
where bpp is defined and read into display_info, hence bpp from
VBT will be used only when bpc in display_info is zero.
v2: use display_info.bpc for deciding when to use vbt_bpp (Jani)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just a preparation patch to make clear what operation we
are performing. There is no functional change on the sink crc
logic.
hsw_disable_ips has been moved a bit further in the start function
to avoid disabling ips when sink crc is not going to be started.
and to avoid goto on this function.
v2: explain why hsw_disable_ips() call place has changed.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
