There is a known issue on some Intel platforms which causes
pause/release to run into xrun's during capture usecases.
The suggested workaround to address the issue is to
disable the entry of lower power L1 state in the physical
DMI link when there is a capture stream open.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927200538.660-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before clearing stream statuses, ensure RUN bit update has taken
effect by reading the value back.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per the HW recommendation, after setting the RUN bit
(start as 1, stop as 0), software must read the bit back
to make sure the bit is set right, before modifying related
control registers/re-starting the DMA engine.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should use irq disabled mode when read/write hda registers from
thread context, as we need to hold the same bus->reg_lock in interrupt
context hda_dsp_stream_interrupt(), otherwise, when we are holding the
lock in hda_dsp_stream_hw_free() and the interrupt arrives, we will get
deadlock in the interrupt handler.
Error logs like this:
[ 5.603606] CPU0
[ 5.603606] ----
[ 5.603607] lock(&(&bus->reg_lock)->rlock);
[ 5.603608] <Interrupt>
[ 5.603609] lock(&(&bus->reg_lock)->rlock);
[ 5.603610]
*** DEADLOCK ***
[ 5.603611] 2 locks held by pulseaudio/2329:
[ 5.603612] #0: 000000005fcf26c6 (&card->mutex/1){+.+.}, at: dpcm_fe_dai_hw_free+0x2b/0x110 [snd_soc_core]
[ 5.603619] #1: 00000000ef369faf (&rtd->pcm_mutex){+.+.}, at: soc_pcm_hw_free+0x2e/0x1c0 [snd_soc_core]
The fix is simple, let's switch to use spin_lock/unlock_irq().
Reported-by: Xun Zhang <xun2.zhang@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the stream interrupt handler to always wake up the
IRQ thread if the status register is valid. The IRQ thread
performs the check for stream interrupts and RIRB interrupts
in a loop to handle the case of missed interrupts when an
unsolicited response from the codec is received just before the
stream interrupt handler is completed.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Host and link DMA are decoupled during FE hw_params. So,
they must be coupled in hw_free if the link DMA channel
is idle.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the HW programming sequence requirement that the host
and link DMA channels need to be coupled/decoupled during pcm
hw_params, the host DMA channel corresponding to the link
DMA channel in use for hostless streams needs to be reserved.
This is achieved by adding a host_reserved flag in the
sof_intel_hda_stream structure which is checked when assigning
a host DMA channel.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a snd_sof_dev member to sof_intel_hda_stream. This will be
used to access the snd_sof_dev during link hw_params callback.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream and IPC share the same interrupt. The stream interrupt
handler mistakenly uses the ipc interrupt and return IRQ_HANDLED,
causing the ipc interrupt to be missed.
Make sure the stream interrupt handler only deals with stream-related
interrupts.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add stream_max into struct sof_intel_hda_dev to store the total hda
stream number that the platform can support, and initialize it at
stream_init.
This can be used later e.g. for stream bitmask.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to a wrapper function which schedules the actual call of
snd_pcm_period_elapsed after the current IPC is completed.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
