Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the MPSC register, add the functions that configure port-based
packet sampling in hardware and the necessary datatypes in the
mlxsw_sp_port struct. In addition, add the necessary trap for sampled
packets and integrate with matchall offloading to allow offloading of the
sample tc action.
The current offload support is for the tc command:
tc filter add dev <DEV> parent ffff: \
matchall skip_sw \
action sample rate <RATE> group <GROUP> [trunc <SIZE>]
Where only ingress qdiscs are supported, and only a combination of
matchall classifier and sample action will lead to activating hardware
packet sampling.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.
Fix this by adding the original skb release to the main path.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlxsw driver.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the order of the free directives to match the port init function
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mlxsw spectrum driver only supports offloading the matchall
classifier together with the mirred action. To allow more matchall tc
offloads, make the code symmetric so that it can be easily extended later
on for other actions.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is split we should mark it as such, as otherwise the split
ports aren't renamed correctly (e.g. sw1p3 -> sw1p3s1) and the unsplit
operation fails:
$ devlink port split sw1p3 count 4
$ devlink port unsplit eth0
devlink answers: Invalid argument
[ 598.565307] mlxsw_spectrum 0000:03:00.0 eth0: Port wasn't split
Fixes: 67963a33b4 ("mlxsw: Make devlink port instances independent of spectrum/switchx2 port instances")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Reviewed-by: Elad Raz <eladr@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure policers and connect them to trap groups.
While many trap groups share policer's configuration they don't share
the actual policer because each trap group represents a different
flow / protocol and we don't want one of them to be able to exceed its
rate on behalf of another.
For example, if STP and LLDP gets to send 128 packets/sec each, if we
put them in one 256 packets/sec policer, one can send 200 packets while
the other only 50.
Note that IP2ME covers lots of flows, so it's limit is set to match the
cpu ability to handle data.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups can be used to control traps priority, both in terms of
which trap "wins" if a packet matches two traps (priority) and in terms
of packets from which trap group will be scheduled to the cpu first (tc).
They can also be used to set rate limiters (policers) on them (will be
added in the next patches).
Currently, we support two trap groups. In Spectrum we want a better
resolution, so every protocol / flow will have a different trap group,
so we can control its parameters separately. Once the policers will be
implemented, it will also allow us limit the rate of each protocol by
itself.
This patch change the trap group list to include:
* the emad trap group, which is shared for all the devices.
* Switchx2's trap groups, which are a copy of the current trap groups.
* Spectrum's new trap groups, in order to match the above guidelines.
(Switchib is using only the emad trap group, so it require no changes).
This patch also includes new configuration for Spectrum's trap groups,
with primary priority order within them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trap for BGP protocol that was previously trapped by the generic trap
for IP2ME. This trap will allow us to have better control (over priority
and rate) of the traffic.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups have many options which we currently set to default values.
In the next patches we will use many of them with non-default values.
Some of these options have no default value, so this patch sets them as
params for the trap group set function. Others almost always use the same
values, so the set function will use this default values. In the rare cases
when they will need to be with other values, these values can be set
directly (using the macros for fields in registers).
Parameters without default value:
TC - the traffic class for packets that hit this trap group.
(old default is the max tc)
priority - if one packet hits multiple trap groups, the group with the
higher priority will "catch" it. (old default is 0)
policer - limit rate policer (old default is disabled)
Default parameters:
swid - switch id, relevant for the emad trap only, ignored on Spectrum.
(new default is 0)
rdq - CPU receive descriptor queue (new default is identical to trap
group id)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the emad trap init was done in the core. In the future we will
want to add some changes to the traps groups, according to device type.
This commit create a driver function to create the trap group for the
emad, so later it can be changed by devices. It also changes the emad
registration to use the new generic functions.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we set the trap group to pre-determined option, based on whether
it is an rx or event trap.
This commit adds a possibility to chose the trap group, so it can be set
to different values in the following patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change trap setting function so instead of determining the trap group by
trap id, it gets it as a parameter (so later we can have different trap
groups for Spectrum and Switchx2).
Add "is_ctrl" parameter to the trap setting function. It control whether
the trapped packets wait in a designated control buffer or in their
default one. This parameter is ignored by Switchx2 and Switchib.
Add these parameters to the traps array in Spectrum, Switchx2 and
Switchib.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the old rx listener struct definitions by the generic ones.
Use the new generic registering / unregistering functions for them.
Add some macros to organize the trap list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 99724c18fc ("mlxsw: spectrum: Introduce support for
router interfaces") we no longer rely on flooding traffic to the CPU in
order to trap packets intended for the host itself. Therefore, the FDB
MC trap can be removed.
Remove traps for protocols that are not supported yet.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When binding port to a newly created span entry, its refcount is
initialized to zero even though it has a bound port. That leads
to unexpected behaviour when the user tries to delete that port
from the span entry.
Fix this by initializing the reference count to 1.
Also add a warning to put function.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <generated/utsrelease.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we are about to introduce IB port APIs, we will add prefixes to
existing APIs.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink register/unregister is done directly from
spectrum/switchx2 port create/remove functions. With a need to
introduce a port type change, the devlink port instances have to be
persistent across type changes, therefore across port create/remove
function calls. So do a bit of reshuffling to achieve that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add Infiniband support to PTYS. In order to maintain proper
conventions, we will change pack and unpack prefix to eth.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be symmentrical with create and do the check outside the remove function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently discovered a bug in the firmware in which a field's length in
one of the registers was incorrectly set. This caused the firmware to
access garbage data that wasn't initialized by the driver and therefore
emit error messages.
While the bug is already fixed and the driver usually zeros the buffers
passed to the firmware, there are a handful of cases where this isn't
done. Zero the buffer in these cases and prevent similar bugs from
recurring, as they tend to be hard to debug.
Fixes: 52581961d8 ("mlxsw: core: Implement fan control using hwmon")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this so the sysfs has "device" link correctly set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, mlxsw_pci.ko is the module that registers PCI table for all
drivers (spectrum and switchx2). That is problematic for example with
dracut. Since mlxsw_spectrum.ko and mlxsw_switchx2.ko are loaded
dynamically from within mlxsw_core.ko, dracut does not have track of
them and avoids them from being included in initramfs.
So make this in an ordinary way and define the PCI tables in individual
driver modules, so it can be properly loaded and included in dracut
initramfs image. As a side effect, this patch could remove no longer
necessary driver "kind" strings which were used to link PCI ids with
individual mlxsw drivers.
Suggested-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of resources is going to get much bigger, ease up the
addition by simly defining IDs. Convert the existing structure members
to a set array, one for validity, one for values. Introduce a set of
getters and setters for easy access.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforce const for getter buf args.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mlxsw users to new dev walk API. This is just a code conversion;
no functional change is intended.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to specify that the mlxsw spectrum driver needs additional
headroom for packets, there have been use of the hard_header_len field of
the netdevice struct.
This commit changes that to use needed_headroom instead, as this is the
correct way to do that.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an earlier check and return if err is non-zero, so
the check to see if it is zero is redundant in every iteration
of the loop and hence the check can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace max rif const with using the result from resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add max system ports, max regions and max vlan groups to resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resources from resource query to determine values for
the profile configuration.
Add KVD determined section sizes to the resources struct.
Change the profile struct and value to match this changes.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use max lag and max ports in lag resources as the result of resource query
instead of using const to save them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offloads stats functions are local to this file, make them static.
Fixes: fc1bbb0f18 ('mlxsw: spectrum: Implement offload stats ndo [..]')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:251:28: warning: symbol
'mlxsw_sp_span_entry_find' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:265:28: warning: symbol
'mlxsw_sp_span_entry_get' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: warning: mixing
different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: int enum
mlxsw_sp_span_type versus
drivers/net/ethernet/mellanox/mlxsw//spectrum.c:367:56: int enum
mlxsw_reg_mpar_i_e
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: int
enum mlxsw_reg_sbxx_dir versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:598:32: int
enum devlink_sb_pool_type
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: int
enum mlxsw_reg_sbpr_mode versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_buffers.c:600:39: int
enum devlink_sb_threshold_type
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: warning:
mixing different enum types
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: int
enum mlxsw_sp_l3proto versus
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:255:54: int
enum mlxsw_reg_ralxx_protocol
...
drivers/net/ethernet/mellanox/mlxsw//spectrum_router.c:1749:6: warning:
symbol 'mlxsw_sp_fib_entry_put' was not declared. Should it be static?
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default statistics ndo to return HW statistics
(like the one returned by ethtool_ops).
The HW stats are collected to a cache by delayed work every 1 sec.
Implement the offload stat ndo.
Add a function to get SW statistics, to be called from this function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the deprecated {get,set}_settings callbacks and instead add
{get,set}_link_ksettings along with support for newly available speeds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device can support multiple port types, so don't return on first
match.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case port isn't operational we shouldn't report the port type, but
instead return PORT_OTHER. This is consistent with most other drivers
that return PORT_OTHER when media type can't be determined.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If autonegotiation was performed successfully, then we should report the
link partner's advertised speeds instead of the operational speed of the
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the device always reported autonegotiation to be off
although it was on by default.
Allow the user to disable / enable autonegotiation and report its status
correctly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
