It is not allowed to call usb_clear_halt() after urbs are submitted.
That causes oops sometimes. Move whole streaming_ctrl() logic to
power_ctrl() in order to avoid wrong usb_clear_halt() use. Also,
configuring streaming endpoint in streaming_ctrl() sounds like a
little bit wrong as it is aimed for control stream gate.
Reported-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After qt1010 change that device seems to survive from reset resume.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is workaround / partial fix.
rtl2832u_power_ctrl() and rtl2832u_frontend_attach() needs to
be go through carefully and fix properly. There is clearly
some logical errors when handling power-management ang GPIOs...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stream did not start anymore after stream was stopped once.
Following error can be seen, xhci_hcd
WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
usb_clear_halt for streaming endpoint helps.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On a few places, := were using instead of +=, causing drivers to
not compile.
While here, standardize the usage of += on all cases where multiple
lines are needed, and for obj-y/obj-m targets, and := when just one
line is needed, on <module>-obj rules.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Identified-by: Antti Polosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add .reset_resume() support.
Also some other small changes for suspend / resume.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move initial suspend / resume support from dvb_usb_v2 to dvb_frontend
as it is dvb general feature that could be used all dvb devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Put device full sleep on suspend, wake-up it on resume and acquire
retune in order to return same television channel.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
debug_dump macro was defined twice when CONFIG_DVB_USB_DEBUG was
not set. Move debug_dump macro to correct place.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
