The GMBUS controller GMBUS3 register is double-buffered. Take advantage
of this by writing two 4-byte words before the first wait for HW_RDY.
This helps keep the GMBUS controller from becoming idle during long writes.
In fact, during experiments using the GMBUS interrupts, the HW_RDY
interrupt would only trigger for transactions >4 bytes after 2 writes
to GMBUS3.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A common method of probing an i2c bus is trying to do a zero-length write.
Handle this case by checking the length first before decrementing it.
This is actually important, since attempting a zero-length write is one
of the ways that i2cdetect and i2c_new_probed_device detect whether
there is device present on the bus with a given address.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just noticed this while verifying the VGA disable code.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory this will have performance and power improvements. Performance
because we don't need to stall when the scanout BO is busy, and power
because we don't have to stall when the BO is busy (and the ring can
even go to sleep if the HW supports it).
v2:
squash 2 patches into 1 (me)
un-inline the enable_semaphores function (Daniel)
remove comment about SNB hangs from i915_gem_object_sync (Chris)
rename intel_enable_semaphores to i915_semaphore_is_enabled (me)
removed page flip comment; "no why" (Chris)
To address other comments from Daniel (irc):
update the comment to say 'vt-d is crap, don't enable semaphores'
- I think you misinterpreted Chris' comment, it already exists.
checking out whether we can pageflip on the render ring on ivb (didn't
work on early silicon)
- We don't want to enable workarounds for early silicon unless we have
to.
- I can't find any references in the docs about this.
optionally use it if the fb is already busy on the render ring
- This should be how the code already worked, unless I am
misunderstanding your meaning.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By simplifying the rules to calling get_fence when writing to the
through the GTT in a tiled manner, and calling put_fence before writing
to the object through the GTT in a linear manner, the code becomes
clearer and there is less chance of making a mistake.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: fixed up conflict with ppgtt code and spelling in a new
comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RC6 residency should be in intervals of 1.28us, and the counter wraps.
Here is an example using awk to get the various RC6 and RC6+ residency
times in seconds, since boot.
cat /sys/kernel/debug/dri/0/i915_drpc_info | grep residency | awk -F':' -F' ' '{print $5 * 1.28 / 1000000}'
This is primarily for QA, but has other applications as well. An
upcoming patch to add interfaces should be more interesting to
application developers.
v2: move comment to the correct place
v3: display with %u instead of %d, for Ouping
CC: Ouping Zhang <ouping.zhang@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter wrote
First pull request for 3.5-next, slightly large than usual because new
things kept coming in since the last pull for 3.4.
Highlights:
- first batch of hw enablement for vlv (Jesse et al) and hsw (Eugeni). pci
ids are not yet added, and there's still quite a few patches to merge
(mostly modesetting). To make QA easier I've decided to merge this stuff
in pieces.
- loads of cleanups and prep patches spurred by the above. Especially vlv
is a real frankenstein chip, but also hsw is stretching our driver's
code design. Expect more to come in this area for 3.5.
- more gmbus fixes, cleanups and improvements by Daniel Kurtz. Again,
there are more patches needed (and some already queued up), but I wanted
to split this a bit for better testing.
- pwrite/pread rework and retuning. This series has been in the works for
a few months already and a lot of i-g-t tests have been created for it.
Now it's finally ready to be merged. Note that one patch in this series
touches include/pagemap.h, that patch is acked-by akpm.
- reduce mappable pressure and relocation throughput improvements from
Chris.
- mmap offset exhaustion mitigation by Chris Wilson.
- a start at figuring out which codepaths in our messy dri1/ums+gem/kms
driver we actually need to support by bailing out of unsupported case.
The driver now refuses to load without kms on gen6+ and disallows a few
ioctls that userspace never used in certain cases. More of this will
definitely come.
- More decoupling of global gtt and ppgtt.
- Improved dual-link lvds detection by Takashi Iwai.
- Shut up the compiler + plus fix the fallout (Ben)
- Inverted panel brightness handling (mostly Acer manages to break things
in this way).
- Small fixlets and adjustements and some minor things to help debugging.
Regression-wise QA reported quite a few issues on ivb, but all of them
turned out to be hw stability issues which are already fixed in
drm-intel-fixes (QA runs the nightly regression tests on -next alone,
without -fixes automatically merged in). There's still one issue open on
snb, it looks like occlusion query writes are not quite as cache coherent
as we've expected. With some of the pwrite adjustements we can now
reliably hit this. Kernel workaround for it is in the works."
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (101 commits)
drm/i915: VCS is not the last ring
drm/i915: Add a dual link lvds quirk for MacBook Pro 8,2
drm/i915: make quirks more verbose
drm/i915: dump the DMA fetch addr register on pre-gen6
drm/i915/sdvo: Include YRPB as an additional TV output type
drm/i915: disallow gem init ioctl on ilk
drm/i915: refuse to load on gen6+ without kms
drm/i915: extract gt interrupt handler
drm/i915: use render gen to switch ring irq functions
drm/i915: rip out old HWSTAM missed irq WA for vlv
drm/i915: open code gen6+ ring irqs
drm/i915: ring irq cleanups
drm/i915: add SFUSE_STRAP registers for digital port detection
drm/i915: add WM_LINETIME registers
drm/i915: add WRPLL clocks
drm/i915: add LCPLL control registers
drm/i915: add SSC offsets for SBI access
drm/i915: add port clock selection support for HSW
drm/i915: add S PLL control
drm/i915: add PIXCLK_GATE register
...
Conflicts:
drivers/char/agp/intel-agp.h
drivers/char/agp/intel-gtt.c
drivers/gpu/drm/i915/i915_debugfs.c
On coherent systems (not-AGP) the IB should be in cached memory so should
be just as fast, so we can avoid copying to temporary pages and just use it
directly.
provides minor speedups on rv530: gears ~1820->1860, ipers: 29.9->30.6,
but always good to use less CPU if we can.
v3: cleanup unneeded bits.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This closes a race seen with kexec where we enable PCI bus mastering
but the card has been reinitialised fully yet.
This was previously fixed by a patch from Jerome, but this should
close the race completely.
v2: add SI support as suggested by Alex.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I made a mistake, please forgive me.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48254
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When booting with EFI, Apple botched this one up.
v2: Switch the quirk dmesg output to DRM_INFO.
v3: Actually git add the new things ...
Tested-by: Austin Lund <austin.lund@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42842
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add informational dmesg output where it does not yet exist.
In case a quirk matches too much, this information is crucial for
debugging such a bug report.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It exists way back to gen2, bug got moved around on gen4 a bit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-and-tested-by: Bo Wang < bo.b.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36997
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ums is already disabled, but on ilk we can additionally disable gem
initialization when using user mode setting. Upstream never support
ilk without kernel modesetting and not even the RHEL ilk ums backport
needs gem - that driver is based on xf86-video-intel version 2.2,
which is pre-gem.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spurred by an irc discussion, let's start to clear up which parts of
our kms + ums/gem + ums/dri1 + vbios/dri1 kernel driver pieces
userspace in the wild actually uses.
The idea is that we introduce checks at entry-points (module load
time, ioctls, ...) first and then reap any obviously dead code in a
second step.
As a first step refuse to load without kms on chips where userspace
never supported ums. Now upstream hasn't supported ums on ilk, ever.
But RHEL had the great idea to backport the kms support to their ums
driver.
Cc: Dave Airlie <airlied@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv, ivb and snb all share the gen6+ gt irq handling. 3 copies of the
same stuff is a bit much, so extract it into a little helper.
Now ilk has a different gt irq handling than snb, but shares the same
irq handler (due to the similar display block). So also extract the
ilk gt irq handling to clearly separate these two things.
Nice side effect of this is that we can complete Ben Widawsky's gen6+
irq bit #define cleanup and call the render irq also with the GEN6
alias. Beforehand that code was shared with ilk, and neither option
really made much sense.
As a bonus this enables the error interrupt handling lifted from the
vlv code on snb and ivb, too.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Antagonized-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Top-level interrupt bits are usually found in the display block. It
therefore makes sense to use HAS_PCH_SPLIT in i915_irq.c
But the irq stuff in intel_ring.c only concerns itself with render
core/gt-level interrupt sources. It therefore makes more sense to
switch based on gpu gen.
Kills a vlv special case.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got copy-pasted from an older version. The newer kinds of
workarounds don't need this anymore.
Shame on me for not noticing when picking up the vlv irq patch.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can now open-code the get/put irq functions as they were just
abstracting single register definitions.
It would be nice to merge this in with the IRQ handling code... but that
is too much work for me at present. In addition I could probably
collapse this in to a lot of the Ironlake stuff, but I don't think it's
worth the potential regressions.
This patch itself should not effect functionality.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- gen6 put/get only need one argument
rflags and gflags are always the same (see above explanation)
- remove a couple redundantly defined IRQs
- reordered some lines to make things go in descending order
Every ring has its own interrupts, enables, masks, and status bits that
are fed into the main interrupt enable/mask/status registers. At one
point in time it seemed like a good idea to make our functions support
the notion that each interrupt may have a different bit position in the
corresponding register (blitter parser error may be bit n in IMR, but
bit m in blitter IMR). It turned out though that the HW designers did us
a solid on Gen6+ and this unfortunate situation has been avoided. This
allows our interrupt code to be cleaned up a bit.
I jammed this into one commit because there should be no functional
change with this commit, and staging it into multiple commits was
unnecessarily artificial IMO.
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet:
- fixed up merged conflict with vlv changes.
- added GEN6 to GT blitter bit, we only use it on gen6+.
- added a comment to both ring irq bits and GT irq bits that on gen6+
these alias.
- added comment that GT_BSD_USER_INTERRUPT is ilk-only.
- I've got confused a bit that we still use GT_USER_INTERRUPT on ivb
for the render ring - but this goes back to ilk where we have only
gt interrupt bits and so we be equally confusing if changed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDIA is detected via the DDI_BUF_CTL registers bit 0, but for DDIB, DDIC
and DDID we need to consult SFUSE_STRAP values.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Watermark line time registers for display low power watermark.
v2: improve bit names as suggested by Chris Wilson
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The WR PLL can drive the DDI ports at fixed frequencies for HDMI, DVI, DP
and FDI.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are used to control the display core clock.
v2: change the enable bit setting, spotted by Rodrigo Vivi.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Different registers are identified by their target id and offset. To
simplify their programming, they are called as <RegisterName><TargetId>.
For example, SSCCTL register accessed through SBI at target id 6 and
offset 0c is called SBI_SSCCTL6.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple clocks can drive different outputs.
v2: use the port enums to access individual ports
v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This PLL control can drive DDI ports at desired frequencies for
DisplayPort and FDI connections.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are responsible for the Sideband Interface programming.
v2: rename SBI bits to better reflect their meaning
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those registers are used to train DDI buffer translations for each link
type.
v2: access each port registers through the DDI_BUF_TRANS macro
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one instance of those registers for each DDI port.
v2: access registers via the DDI_BUF_CTL() macro
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one set of those registers for each port.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is one set of those registers for each pipe.
v2: use port enum to access individual registers
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is one set of such registers for each pipe (A/B/C/EDP).
v2: update to use DDI PORTS enum
v1 Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are 5 DDI ports on Haswell. Port A is always enabled, and is the one
connected to eDP, and Port E is the one that can be connected to the PCH
using FDI protocol. Ports B, C, D and E can be used for digital outputs.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This defines the registers used by different power wells.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds product definitions for desktop, mobile and server boards.
v2: split into a separate patch, add .has_pch_split feature.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The macro is becoming too complex and with VLV upon us it can lead to
confusion. So transforming this into a feature check instead.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: fixed conflict with is_valleyview addition.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit d06221c061.
It turns out to trigger the "BUG_ON(!PageCompound(page))" in kfree(),
apparently because the code ends up trying to free somethng that was
never kmalloced in the first place.
BenH points out that the patch was untested and wasn't meant to go into
the upstream kernel that quickly in the first place.
Backtrace:
bios_shadow
bios_shadow_prom
nv_mask
init_io
bios_shadow
nouveau_bios_init
NVReadVgaCrtc
NVSetOwner
nouveau_card_init
nouveau_load
Reported-by: Meelis Roos <mroos@linux.ee>
Requested-by: Dave Airlie <airlied@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm update from Dave Airlie:
"This pull just contains a forward of the Intel fixes from Daniel.
The only annoyance is the RC6 enable, which really should have made
-next, but since Ubuntu are shipping it I reckon its getting a good
testing now by the time 3.4 comes out.
The pull from Daniel contains his pull message to me:
"A few patches for 3.4, major part is 3 regression fixes:
- ppgtt broke hibernate on snb/ivb. Somehow our QA claims that it
still works, which is why this has not been caught earlier.
- ppgtt flails in combination with dmar. I kinda expected this one :(
- fence handling bugfix for gen2/3. Iirc this one is about a year
old, fix curtesy Chris Wilson. I've created an shockingly simple
i-g-t test to catch this in the future."
Wrt regressions I've just got a report that gmbus (newly enabled
again in 3.4) is a bit noisy. I'm looking into this atm.
Also included are the rc6 enable patches for snb from Eugeni. I
wanted to include these in the main 3.4 pull but screwed it up.
Please hit me. Imo these kind of patches really should go in
before -rc1, but in thise case rc6 has brought us tons of press and
guinea pigs^W^W testers and ubuntu is already running with it. So
I estimate a pretty small chance for this to blow up.
And some smaller things:
- two minor locking snafus
- server gt2 ivb pciid
- 2 patches to sanitize the register state left behind by the bios
some more
- 2 new quirk entries
- cs readback trick against missed IRQs from ivb also enabled on snb
- sprite fix from Jesse"
Let's see if the "enable RC6 on sandybridge" finally works and sticks.
I've been enabling it by hand (i915.i915_enable_rc6=1) for several
months on my Macbook Air, and it definitely makes a difference (and has
worked for me). But every time we enabled it before it showed some odd
hw buglet for *somebody*.
This time it's all good, I'm sure.
* 'drm-fixes-intel' of git://people.freedesktop.org/~airlied/linux:
drm/i915: treat src w & h as fixed point in sprite handling code
drm/i915: no-lvds quirk on MSI DC500
drm/i915: Add lock on drm_helper_resume_force_mode
drm/i915: don't leak struct_mutex lock on ppgtt init failures
drm/i915: disable ppgtt on snb when dmar is enabled
drm/i915: add Ivy Bridge GT2 Server entries
drm/i915: properly clear SSC1 bit in the pch refclock init code
drm/i915: apply CS reg readback trick against missed IRQ on snb
drm/i915: quirk away broken OpRegion VBT
drm/i915: enable plain RC6 on Sandy Bridge by default
drm/i915: allow to select rc6 modes via kernel parameter
drm/i915: Mark untiled BLT commands as fenced on gen2/3
drm/i915: properly restore the ppgtt page directory on resume
drm/i915: Sanitize BIOS debugging bits from PIPECONF
Pull drm fixes from Dave Airlie:
"Mainly nouveau fixes, one for a regressions in -rc1, fixes for booting
on a ppc G5, and a Kconfig fix. Two radeon fixes, one oops, one s/r
fix. One udl mmap fix. And one core drm fix to stop bad fbdev apps
overwriting bits of ram."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Validate requested virtual size against allocated fb size
drm/radeon: Don't dereference possibly-NULL pointer.
mm, drm/udl: fixup vma flags on mmap
drm/radeon/kms: fix fans after resume
nouveau/bios: Fix tracking of BIOS image data
nouveau: Fix crash when pci_ram_rom() returns a size of 0
drm/nouveau: select POWER_SUPPLY
drm/nouveau: inform userspace of relaxed kernel subchannel requirements
Revert "drm/nouveau: inform userspace of new kernel subchannel requirements"
drm/nouveau: oops, create m2mf for nvd9 too
mplayer -vo fbdev tries to create a screen that is twice as tall as the
allocated framebuffer for "doublebuffering". By default, and all in-tree
users, only sufficient memory is allocated and mapped to satisfy the
smallest framebuffer and the virtual size is no larger than the actual.
For these users, we should therefore reject any userspace request to
create a screen that requires a buffer larger than the framebuffer
originally allocated.
References: https://bugs.freedesktop.org/show_bug.cgi?id=38138
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was missed when we converted the source values to 16.16 fixed point.
Cc: stable@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This hardware doesn't have an LVDS, it's a desktop box. Fix incorrect
LVDS detection.
Cc: stable@kernel.org
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_drm_thaw was not locking the mode_config lock when calling
drm_helper_resume_force_mode. When there were multiple wake sources,
this caused FDI training failure on SNB which in turn corrupted the
display.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: Konstantin Belousov <kostikbel@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
