Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The original device tree binding for this driver, from Viresh Kumar
unfortunately conflicted with the generic DMA binding, and did not allow
to completely seperate slave device configuration from the controller.
This is an attempt to replace it with an implementation of the generic
binding, but it is currently completely untested, because I do not have
any hardware with this particular controller.
The patch applies on top of the slave-dma tree, which contains both the base
support for the generic DMA binding, as well as the earlier attempt from
Viresh. Both of these are currently not merged upstream however.
This version incorporates feedback from Viresh Kumar, Andy Shevchenko
and Russell King.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dw_dmac driver already supports device tree but it used to have its platform
data passed the non-DT way.
This patch does following changes:
- pass platform data via DT, non-DT way still takes precedence if both are used.
- create generic filter routine
- Earlier slave information was made available by slave specific filter routines
in chan->private field. Now, this information would be passed from within dmac
DT node. Slave drivers would now be required to pass bus_id (a string) as
parameter to this generic filter(), which would be compared against the slave
data passed from DT, by the generic filter routine.
- Update binding document
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Fixed __devinit usage]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
SPEAr platforms now support DT and so must convert all drivers to support DT.
This patch adds DT probing support for Synopsys DMA controller and updates its
documentation too.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
