By Stephen Warren (5) and Peter De Schrijver (1)
via Stephen Warren
* 'for-3.5/tegra30-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
ARM: tegra: set up audio clocks for tegra30 dt
ARM: tegra: Initialize pll_p_out1
ARM: tegra: provide clock aliases for AHUB configlink
Signed-off-by: Olof Johansson <olof@lixom.net>
By Stephen Warren (30) and others
via Stephen Warren
* 'for-3.5/usb-ulpi' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (7 commits)
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
+ depends/pinctrl/mergebase branch
Pinctrl mergebase has a conflict in drivers/pinctrl/core.c that was resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
Direct keys usage may not start from KP_DKIN0, add a msk option
to configure the specifics for platforms that can skip some keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
KPDK_DK only indicates the pin level of direct key.
So it is related to board, and low level may be active which
indicates that a key is pressed.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Ensure that the USB ULPI signals are not tri-stated, and have no pull-
up or pull-down.
Ensure that the pingroup hosting the USB ULPI reset signal (GPIO PV0 or
PV1 depending on the board, so UAC) is not tri-stated, and has no pull-
up or pull-down.
This change appears larger than it is due to the grouping and sorting of
the pin configuration data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ULPI PHYs have a reset signal, and different boards use a different GPIO
for this task. Add a property to device tree to represent this.
I'm not sure if adding this property to the EHCI controller node is
entirely correct; perhaps eventually we should have explicit separate
nodes for the various PHYs. However, we don't have that right now, so this
binding seems like a reasonable choice.
Cc: <devicetree-discuss@lists.ozlabs.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Not all boards use GPIO_PV0 as the ULPI PHY reset signal. Instead of
hard-coding this GPIO into devices.c, make the board files set it
explicitly. This will allow the PHY code to differentiate between set and
unset values, and hence know when to read the value from device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 is used on all/most Tegra boards to drive the cdev2 output pin
to provide a reference clock to a ULPI USB PHY. This reference clock must
run at 24MHz, and the cdev2 output has no additional dividers.
Remove board-paz00.c's now-duplicate initialization of this clock.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 40f9cf0 "ARM: tegra: reparent sclk to pll_c_out1" changed the
rate of hclk. Since pclk is derived from that, and only has integer
dividers, the pclk rate needs to change in the same fashion, from 54MHz
to 60MHz.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 needs to be used for other purposes. Reparent sclk so that
it runs from pll_c. Change sclk's rate to 120MHz from 108MHz since this
is the lowest precise rate that can be achieved by dividing the pll_c
rate without reducing the sclk rate. (600/5=120, 600/5.5=109.0909...,
600/6=100).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_c will be used as a clock source. Fill in tegra_pll_c_freq_table[]
so that it's possible to explicitly initialize the PLL.
NVIDIA's downstream nv-3.1 kernel and the ChromeOS kernel have different
pll_c tables. nv-3.1 contains entries for 522MHz and 598MHz output,
whereas the ChromeOS kernel contains entries for 600MHz output. I chose
to upstream the ChromeOS values for now, since the 600MHz rate appears
to match the default rate of this PLL when the HW boots, and it's not
clear to me why 522 or 598MHz are more useful.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: wrote commit description]
Add WM8903 codec nodes, and top-level sound complex node for basic
analog audio over headset jack and internal speakers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Both the Tegra30 I2S and AHUB modules used clocks, and hence currently
require AUXDATA in order to get specific device names so that clock
lookups work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Set up the audio clock tree for Tegra30 in an equivalent fashion to the
existing setup for Tegra20.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
pll_a uses pll_p_out1 as its parent. Therefore this clock needs to be
initialized to make sure pll_a has a known input clock. Failure to do so
will cause the system to crash early in the bootup.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra30 AHUB driver must call tegra_periph_reset_deassert() for all
devices on the AHUB's configlink bus. The AHUB driver must be able to
call clk_get_sys() to retrieve the clock parameter for this function.
Add the necessary clock aliases to allow this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Otherwise cpu_active_mask will not set, which lead to other issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gHlK
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
pfm_vm_munmap() is simply vm_munmap() and pfm_remove_smpl_mapping()
always get current as the first argument.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the vm_brk() function, this is the same as "do_munmap()", except it
does the VM locking for the caller.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It does the same thing as "do_brk()", except it handles the VM locking
too.
It turns out that all external callers want that anyway, so we can make
do_brk() static to just mm/mmap.c while at it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68k arch fixes from Greg Ungerer:
"This contains four fixes for 3.4. Two fix and clean up compilation
for the nommu 68x328 CPU targets. The other two fix the platform
definition and multi-function pin setup of the second eth interface
on the ColdFire 5275 SoC."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: make sure 2nd FEC eth interface pins are enabled on 5275 ColdFire
m68knommu: fix id number for second eth device on 5275 ColdFire
m68knommu: move and fix the 68VZ328 platform bootlogo.h
m68knommu: remove the unused bootlogo.h processing for 68EZ328 and 68VZ328
Pull KVM updates from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: lock slots_lock around device assignment
KVM: VMX: Fix kvm_set_shared_msr() called in preemptible context
KVM: unmap pages from the iommu when slots are removed
KVM: PMU emulation: GLOBAL_CTRL MSR should be enabled on reset
We experienced some issues while compiling some drivers as modules: Joachim has
corrected several of them. We may reduce this number of exported values by
reworking some drivers, in the future.
Some drivers are also modified here, I would like to keep them in the series
as the modifications are really related with our recent move to irqdomains or
simply related with compiler annotations.
I keep dmaengine Kconfig modification in this "fixes" series. The DMA
driver will not be available for 9x5 SoC family otherwise.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPjYSrAAoJEAf03oE53VmQC4gH/3iCpaf1A5tJoGjiPnTetHXK
ziu0f84/sPoxh/l9zXklVaF6AsoHzZzxFfQ1cSh1yHQPjh4pJZSQ68nioNwhXeAq
1uwQjfbbpcIOved/sYzKLBY1v8rnFISXm+yHIYSIcFcZmSWn7eVzYYWb3vilquK/
nzr+2f0Jz2xNIrpfC95ogct7LHrtMEPgYgKpUUQNT3+eE6GwqRqJby5fZQMHNuqV
ECzWPCalxo4C0qW0EXuMMAukdyCo5YKoKNt10P2klyNL33Z1cIEPGkKdcIJP5yiJ
y4Qs1e5xlQeMW0SlEImoRPEObOI/mn5PFxs6nwtDlE6JEW0npjHjB9g2jTi0tGE=
=R4q6
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
Here is another fixes series for AT91 designed for 3.4-rc.
We experienced some issues while compiling some drivers as modules: Joachim has
corrected several of them. We may reduce this number of exported values by
reworking some drivers, in the future.
Some drivers are also modified here, I would like to keep them in the series
as the modifications are really related with our recent move to irqdomains or
simply related with compiler annotations.
I keep dmaengine Kconfig modification in this "fixes" series. The DMA
driver will not be available for 9x5 SoC family otherwise.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
dmaengine: Kconfig: fix Atmel at_hdmac entry
USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
USB: ohci-at91: change annotations for probe/remove functions
leds-atmel-pwm.c: Make pwmled_probe() __devinit
ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
ARM: at91: fix rm9200ek flash size
ARM: at91: remove empty at91_init_serial function
ARM: at91: fix typo in at91_pmc_base assembly declaration
ARM: at91: Export at91_matrix_base
ARM: at91: Export at91_pmc_base
ARM: at91: Export at91_ramc_base
ARM: at91: Export at91_st_base
* 'fixes-for-arm-soc-20120416' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: update defconfig
ARM: ux500: Fix unmet direct dependency
ARM: ux500: wake secondary cpu via resched
Revert one softreset regression and few other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WQ2B
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix regression for bad uart muxing and oops when PM is not set.
Revert one softreset regression and few other minor fixes.
* tag 'omap-fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: DMTIMER: fix broken timer clock source selection
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
ARM: OMAP: sram: fix BUG in dpll code for !PM case
ARM: OMAP2/3: VENC hwmods: Remove OCPIF_SWSUP_IDLE flag from VENC slave interface
ARM: OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status"
ARM: OMAP2+: hwmod: add softreset delay field and OMAP4 data
ARM: OMAP1: mux: add missing include
This error appeared in the bcmring_defconfig build:
CC arch/arm/mach-bcmring/core.o
arch/arm/mach-bcmring/core.c:55: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:55: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:56: error: macro "AMBA_APB_DEVICE" requires 6 arguments, but only 5 given
arch/arm/mach-bcmring/core.c:56: warning: type defaults to 'int' in declaration of 'AMBA_APB_DEVICE'
arch/arm/mach-bcmring/core.c:134: error: 'uartA_device' undeclared here (not in a function)
arch/arm/mach-bcmring/core.c:135: error: 'uartB_device' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-bcmring/core.o] Error 1
It appeared as of commit 8ede1ae65e
"ARM: amba: bcmring: use common amba device initializers"
Note that in include/linux/amba/bus.h we have:
#define AMBA_APB_DEVICE(name, busid, id, base, irqs, data) ...
There is an a --> A case error in the busid and a missing zero
placeholder for the id field.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[olof: reworded patch subject]
Signed-off-by: Olof Johansson <olof@lixom.net>
kvm_set_shared_msr() may not be called in preemptible context,
but vmx_set_msr() does so:
BUG: using smp_processor_id() in preemptible [00000000] code: qemu-kvm/22713
caller is kvm_set_shared_msr+0x32/0xa0 [kvm]
Pid: 22713, comm: qemu-kvm Not tainted 3.4.0-rc3+ #39
Call Trace:
[<ffffffff8131fa82>] debug_smp_processor_id+0xe2/0x100
[<ffffffffa0328ae2>] kvm_set_shared_msr+0x32/0xa0 [kvm]
[<ffffffffa03a103b>] vmx_set_msr+0x28b/0x2d0 [kvm_intel]
...
Making kvm_set_shared_msr() work in preemptible is cleaner, but
it's used in the fast path. Making two variants is overkill, so
this patch just disables preemption around the call.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull s390 updates from Martin Schwidefsky:
"A couple of bug fixes, one of them is a TLB flush fix. Included as
well is one small coding style patch and a patch to update the default
configuration."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] Fix compile error in swab.h
[S390] Fix stfle() lowcore protection problem
[S390] cpum_cf: get rid of compile warnings
[S390] irq: simple coding style change
[S390] update default configuration
[S390] fix tlb flushing for page table pages
[S390] kernel: Use local_irq_save() for memcpy_real()
[S390] s390/char/vmur.c: fix memory leak
[S390] drivers/s390/block/dasd_eckd.c: add missing dasd_sfree_request
Rather than having a single tegra-pinctrl driver that determines whether
it's running on Tegra20 or Tegra30, instead have separate drivers for
each that call into utility functions to implement the majority of the
driver. This change is based on review feedback of the SPEAr pinctrl
driver, which had originally copied to Tegra driver structure.
This requires that the two drivers have unique names. Update a couple
spots in arch/arm/mach-tegra for the name change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This adds a complete pinmux configuration to all Tegra20 device tree
files. This allows removal of board-dt-tegra20.c's use of the pinmux
board files, and the special device tree handling in board-pinmux.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
This adds a minimal pinmux configuration to the Tegra Cardhu device
tree. Initially, just the built-in eMMC and SD card slot are configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net
The pinctrl driver is now active and used by all boards. Remove the
old pinmux driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
* Rename old pinmux and new pinctrl platform driver and DT match table
entries, so the new driver gets instantiated.
* Re-write board-pinmux.c, so that it uses pinctrl APIs to configura the
pinmux.
* Re-write board-*-pinmux.c so that the pinmux configuration tables are
in pinctrl format.
Ventana's pin mux table needed some edits on top of the basic format
conversion, since some mux options that were previously marked as
reserved are now valid in the new pinctrl driver. Attempting to use the
old reserved names will result in a failure. Specifically, groups lpw0,
lpw2, lsc1, lsck, and lsda were changed from function rsvd4 to displaya,
and group pta was changed from function rsvd2 to hdmi.
All boards' pin mux tables needed some edits on top of the based format
conversion, since function i2c was split into i2c1 (first general I2C
controller) and i2cp (power I2C controller) to better align function
definitions with HW blocks.
Due to the split of mux tables into pure mux and pull/tristate tables,
many entries in the separate Seaboard/Ventana tables could be merged
into the common table, since the entries differed only in the portion
in one of the tables, not both.
Most pin groups allow configuration of mux, tri-state, and pull. However,
some don't allow pull configuration, which is instead configured by new
groups that only allow pull configuration. This is a reflection of the
true HW capabilities, which weren't fully represented by the old pinmux
driver. This required adding new pull table entries for those new groups,
and setting many other entries' pull configuration to
TEGRA_PINCONFIG_DONT_SET.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Recent pinctrl discussions concluded that gpiolib APIs should in fact do
whatever is required to mux a GPIO onto pins, by calling pinctrl APIs if
required. This change implements this for the Tegra GPIO driver, and removes
calls to the Tegra-specific APIs from drivers and board files.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org> # for sdhci-tegra.c
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Don't call gpio_request() or gpio_direction_input() for ISL29018_IRQ.
This pin is only used as an IRQ, and hence no GPIO configuration should
be necessary; the GPIO/IRQ driver should (and does) perform any required
setup when the IRQ is requested.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Instead of having board files manually request and initialize USB VBUS
GPIOs, fill in the USB driver's platform data and have it do it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Add a vbus_gpio field to platform data. This mirrors the device tree
property nvidia,vbus-gpio. This makes the VBUS GPIO handling identical
between booting with board files and device tree; the driver always does
it.
This removes the need for board files to request and initialize the GPIO
early during their boot process, perhaps even before the GPIO driver is
ready to process the request.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
The imx5_idle() check of the tzic_eanble_wake() return value uses
incorrect (inverted) logic causing all attempt to idle to fail.
Signed-off-by: Robert Lee <rob.lee@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 6b783f7c (irq_domain: Remove irq_domain_add_simple()
replaced irq_domain_add_simple with irq_domain_add_legacy()
Implement this conversion so that imx27-dt can be built again.
Reported-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for CONFIG_REGULATOR_FIXED_VOLTAGE.
Without this option the mx27_3ds cannot have the external Ethernet functional
due to the need of smsc regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
DMTIMER source selection on OMAP1 is broken. omap1_dm_timer_set_src()
tries to use __raw_{read,write}l() to read from and write to physical
addresses, but those functions take virtual addresses.
sparse caught this:
arch/arm/mach-omap1/timer.c:50:13: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:50:13: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:50:13: got unsigned int
arch/arm/mach-omap1/timer.c:52:9: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-omap1/timer.c:52:9: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-omap1/timer.c:52:9: got unsigned int
Fix by using omap_{read,writel}(), just like the other users of the
MOD_CONF_CTRL_1 register in the OMAP1 codebase. Of course, in the long term,
removing omap_{read,write}l() is the appropriate thing to do; but
this will take some work to do this cleanly.
Looks like this was caused by 97933d6 (ARM: OMAP1: dmtimer: conversion
to platform devices) that dangerously moved code and changed it in
the same patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: stable@vger.kernel.org
[tony@atomide.com: updated comments to include the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The current serial UART code, while fidling with ocp idlemode bits,
forget about the smart idle wakeup bit even if it is supported by
UART IP block. This will lead to missing the module wakeup on OMAP's
where the smart idle wakeup is supported.
This was the root cause of the console sluggishness issue, I have been
observing on OMAP4 devices and also can be potential reason for some
other UART wakeup issues.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit (7496ba3 ARM: OMAP2+: UART: Add default mux for all uarts)
wrongly added muxing of default pads for all uarts. This causes
breakage on multiple boards using uart pins for alternate functions.
For example, on zoom3 random oopses can be seen with nfsroot as
the smsc911x ethernet FIFO timings on GPMC bus are controlled
by gpmc_wait2 and gpmc_wait3 pins. This means we can't mux these
pads to uart4 functionality as commit 7496ba3 was doing.
Not all boards tend to use all uarts and most of unused uart pins
are muxed for other purpose. This commit breaks the modules which
where trying to use unused uart pins on their boards.
So remove the default pad muxing. Note that this is not a complete
fix, as we now rely on bootloader set muxing for the uart wake-up
events. Further patching is needed to enable wake-up events for
uarts that are already muxed to uart mode.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Russ Dill <russ.dill@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated comments to describe oops on zoom3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
_omap3_sram_configure_core_dpll is called when SDRC is reprogrammed,
which is done regardless of CONFIG_PM setting, so we always need it's
setup code too. Without this, we hit a BUG() on OMAP3 when kernel is
built without CONFIG_PM:
Reprogramming SDRC clock to 332000000 Hz
------------[ cut here ]------------
kernel BUG at arch/arm/plat-omap/sram.c:342!
Internal error: Oops - BUG: 0 [#1] ARM
...
[<c001c694>] (omap3_configure_core_dpll+0x68/0x6c) from [<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x1)
[<c001b2dc>] (omap3_core_dpll_m2_set_rate+0x138/0x1b0) from [<c001a478>] (omap2_clk_set_rate+0x14/0x2)
[<c001a478>] (omap2_clk_set_rate+0x14/0x20) from [<c001c9dc>] (clk_set_rate+0x54/0x74)
[<c001c9dc>] (clk_set_rate+0x54/0x74) from [<c022b9c8>] (omap_sdrc_init+0x70/0x90)
[<c022b9c8>] (omap_sdrc_init+0x70/0x90) from [<c022f178>] (omap3pandora_init+0x11c/0x164)
[<c022f178>] (omap3pandora_init+0x11c/0x164) from [<c022849c>] (customize_machine+0x20/0x28)
[<c022849c>] (customize_machine+0x20/0x28) from [<c0225810>] (do_one_initcall+0xa0/0x16c)
[<c0225810>] (do_one_initcall+0xa0/0x16c) from [<c02259e0>] (kernel_init+0x104/0x1ac)
[<c02259e0>] (kernel_init+0x104/0x1ac) from [<c0009cec>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
