If I boot my Broadwell machine to X on a system with Mesa Gallium
llvmpipe instead of i965, then kill X and try to run pm_pc8.c, when we
disable PC8 and call gen6_update_ring_freq(), we will get stuck on an
infinite loop because the frequencies are zero and the variables are
unsigned. This happens because we never ran any batch, so we did not
enable RC6, so the variables are zero. If I run gem_exec_nop before
running pm_pc8, everything works as expected because gem_exec_nop
makes RC6 be enabled.
This commit should prevent the infinite loop, which IMHO is already a
good reason to be merged, but it is not the proper fix to the "RC6 is
not being enabled" problem.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a need for duplicated parsing of the RP_STATE_CAPS register (and
the setting of the associated fields). To reuse some code, we can
extract the function into a simple helper.
This patch also addresses the fact that we missed doing this for gen8,
something we should have done anyway.
This could be two patches, one to extract, and one to add gen8, but it's
trivial enough that I think one is fine. I will accept a request to
split it. Please notice the fix addressed by v2 below.
Valleyview is left untouched because it is different.
v2: Logically rebased on top of
commit dd0a1aa19b
Author: Jeff McGee <jeff.mcgee@intel.com>
Date: Tue Feb 4 11:32:31 2014 -0600
drm/i915: Restore rps/rc6 on reset
Note with the above change the fix for gen8 is also handled (which was
not the case in Jeff's original patch).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Programming it outside of the rp0-rp1 range is considered a programming
error. Since we do not know that the previous value would actually be in
the range, program something we've read from the hardware, and therefore
know will work.
This is potentially an issue for platforms whose ranges are outside the
norms given in the programming guide (ie. early silicon)
v2: Use RP1 instead of RPn
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of reading out the CD clock rate from the HW at each modeset, do
this only during driver init and resume and use the cached value during
modeset. This moves things towards a state where the sw and hw side
setup is separated. It's also needed for VLV RPM, where we don't put
device into D0 state until modeset_global_resources is called and thus
can't access any display/gfx registers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If runtime PM is enabled and we unset all modes, we will runtime
suspend after __intel_set_mode() , then function
intel_modeset_check_state() will try to read the HW state while it is
suspended and trigger lots of WARNs because it shouldn't be reading
registers.
So on this patch we make intel_ddi_connector_get_hw_state() return
false in case the power domain is disabled, and we also make
intel_display_power_enabled() return false in case the device is
suspended. Notice that we can't just use
intel_display_power_enabled_sw() because while the driver is being
initialized the power domain refcounts are not reflecting the real
state of the hardware.
Just for reference, I have previously published an alternate patch for
this problem, called "drm/i915: get runtime PM at intel_set_mode".
Testcase: igt/pm_pc8
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we reserve/allocate and free the power context during GT power
enable/disable time. There is no need to do this, we can reserve/allocate
the buffer once during driver loading and free it during driver cleanup.
The re-reservation can also fail in case the driver previously manages to
allocate something on the given fixed address.
The buffer isn't exepected to move even if allocated by the BIOS, for
safety add an assert to check this assumption.
This also fixed a bug for Ville, where re-reserving the context failed
during a GPU reset (I assume because something else got allocated on its
fixed address).
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the rest of the references to drm_i915_private_t. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop hunk in i915_cmd_parser.c]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The speculation is that we can conserve more power by masking off
the interrupts at source (PMINTRMSK) rather than filtering them by the
up/down thresholds (RPINTLIM). We can select which events we know will
be active based on the current frequency versus our imposed range, i.e.
if at minimum, we know we will not want to generate any more
down-interrupts and vice versa.
v2: We only need the TIMEOUT when above min frequency.
v3: Tweak VLV at the same time
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by:Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
What used to be a short-circuit now needs to adjust interrupt masking in
response to user requests for changing the min/max allowed frequencies.
This is currently done by a special case and early return, but the next
patch adds another common action to take, so refactor the code to reduce
duplication.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by:Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 2754436913.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
The partial application of interrupt masking without regard to other
pathways for adjusting the RPS frequency results in completely disabling
the PM interrupts. This leads to excessive power consumption as the GPU
is kept at max clocks (until the failsafe mechanism fires of explicitly
downclocking the GPU when all requests are idle). Or equally as bad for
the UX, the GPU is kept at minimum clocks and prevented from upclocking
in response to a requirement for more power.
Testcase: pm_rps/blocking
Cc: Deepak S <deepak.s@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by:Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not implementing this W/A can lead to hangs.
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we can use different cursor size, we can not hardcode 64 pixels
as the cursor width anymore.
v2: Apply to 965gm/g4x paths as well
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we use different rps events for different platforms or due to wa,
we might end up needing this logic in a lot of places. Instead of
this let's use a variable in dev_priv to track the enabled PM
interrupts.
v2: Initialize pm_rps_events in intel_irq_init() (Ville).
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob the commit message a bit since the English was a bit too
garbled ;-) ]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the renamed RPS struct members, it's easier to skip the local
variables which no longer clarify anything, and if anything just make
the code harder to read.
The real motivation for this patch is actually the next patch, which
attempts to consolidate some of the functionality.
Cc: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The names of the struct members for RPS are stupid. Every time I need to
do anything in this code I have to spend a significant amount of time to
remember what it all means. By renaming the variables (and adding the
comments) I hope to clear up the situation. Indeed doing this make some
upcoming patches more readable.
I've avoided ILK because it's possible that the naming used for Ironlake
matches what is in the docs. I believe the ILK power docs were never
published, and I am too lazy to dig them up.
v2: leave rp0, and rp1 in the names. It is useful to have these limits
available at times. min_freq and max_freq (which may be equal to rp0, or
rp1 depending on the platform) represent the actual HW min and max.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
this leaves a temporarily awkward min_delay (the soft limit) with the
new min_freq (the hardware limit). It's fixed in the next patch.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The existing code (which I changed last) was very convoluted. I believe
it was attempting to skip the overclock portion if the previous pcode
write failed. When I last touched the code, I was preserving this
behavior. There is some benefit to doing it that way in that if the
first pcode access fails, the later is likely invalid.
Having a bit more confidence in my understanding of how things work, I
now feel it's better to have clear, readable, code than to try to skip
over this one operation in an unusual case.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Function intel_init_runtime_pm is supposed to start allowing runtime
PM from that point, but it's called very late on the driver
initialization code, to prevent the driver from trying to suspend
while still initializing. The problem is that variables are accessed
earlier than that, so initalize them at intel_pm_setup, which is
supposed to be the correct place.
Notice that this shouldn't fix any specific bugs because dev_priv is
zeroed when allocated, so the value is already correct right from the
start.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only remaining field of the struct was the lock, which was
useless.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When other platforms add runtime PM support they will also need to
disable interrupts, so move the variable to the runtime PM struct.
Also notice that the longer-term goal is to completely kill the
regsave struct, and I even have patches for that.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was just being used on debugfs and on a WARN inside
hsw_set_power_well. But now that we PC8 is part of runtime PM and we
get/put runtime PM when we get/put any power domain, we shouldn't need
the WARN anymore.
v2: - Rebase.
v3: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we already get/put runtime PM every time we get/put any power
domain, and now PC8 and runtime PM are the same thing.
With this, we can also now kill the hsw_{en,dis}able_package_c8
functions.
v2: - Rebase.
v3: - Rebase.
v4: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because we merged the PC8 and runtime PM features, so calling
intel_runtime_pm_get now has the same meaning, and we plan to just
remove hsw_disable_package_c8 for this exact reason.
My first patch tried to completely kill
intel_aux_display_runtime_get/put, because I was assuming that whoever
needed more than just runtime PM would have to get the appropriate
power domain instead of that, but it seems some people still want the
intel_aux_display_runtime_get abstraction, so keep it until someone
else tries to replace it with the more-standard power domain calls.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since after the latest patches it's only being used to prevent
getting/putting the runtime PM refcount.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The requirements_met variable was used to track two things: enabled
CRTCs and the power well. After the latest chagnes, we get a runtime
PM reference whenever we get any of the power domains, and we get
power domains when we enable CRTCs or the power well, so we should
already be covered, not needing this specific tracking.
v2: - Rebase.
v3: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Any power domain will require the HW to be in PCI D0 state, so just do
the simple thing.
Dear maintainer: since intel_display_power_put() and
intel_display_power_get() are almost identical, git-am has failed
apply the patch on my local machine once: it added both chunks to
put(), instead of one chunk to get() and another to put(). When you
apply this patch to your tree, please check if it is correct.
v2: - Add the warning above.
v3: - Rebase.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.
While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
- We are not aware of anybody wanting a "PC8 without D3" environment.
- If we keep both features as separate, we'll have to to test both
PC8 and PC8+D3 code paths. We're already having a major pain to
make QA do automated testing of just one thing, testing both paths
will cost even more.
- Only Haswell+ supports PC8, so if we want to add runtime PM support
to, for example, IVB, we'll have to copy some code from the PC8
feature to runtime PM, so merging both features as a single thing
will make it easier for enabling runtime PM on other platforms.
This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.
v2: - Rebase.
v3: - Rebase.
- Fully remove the deprecated i915 params since Daniel doesn't
consider them as part of the ABI.
v4: - Rebase.
- Fix typo in the commit message.
v5: - Rebase, again.
- Add a huge comment explaining the different forcewake usage
(Chris, Daniel).
- Use open-coded forcewake functions (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function is only used on ILK+, so rename it accordingly.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure the line_time_us isn't zero in the gmch watermarks code as
that would cause a div by zero. This can be triggered by specifying
a very fast pixel clock for the mode.
At some point we should probably just switch over to using the same
math we use on PCH platforms which avoids such intermediate rounded
results.
Also we should verify the user provided mode much more rigorously.
At the moment we accept pretty much anything.
Note that "very fast mode" here means above 74.25 GHz.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add Ville's clarification of what "very fast" means.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on an early draft from Jesse.
Add support for powering on/off the dynamic power wells on VLV by
registering its display and dpio dynamic power wells with the power
domain framework.
For now power on all PHY TX lanes regardless of the actual lane
configuration. Later this can be optimized when the PHY side setup
enables only the required lanes. Atm, it enables all lanes in all
cases.
v2:
- undef function local COND macro after its last use (Ville)
- Take dev_priv->irq_lock around the whole sequence of
intel_set_cpu_fifo_underrun_reporting_nolock() and
valleyview_disable_display_irqs(). They are short and releasing
the lock in between only makes proving correctness more difficult.
- sanitize local var names in vlv_power_well_enabled()
v3:
- rebase on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict due to my changes in the previous patch.
Also throw in an assert_spin_locked for safety. And finally appease
checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested by Daniel.
v2:
- sanitize the state checking condition, the original was rather
confusing (partly due to the unfortunate naming of
i915.disable_power_well) (Ville)
- simpler message+backtrace generation by using WARN instead of WARN_ON
(Ville)
- check if always-on power wells are truly on all the time
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to do the same for other platforms in upcoming patches.
v2:
- s/p/pipe (Ville)
- Call the new helper with the vbl_lock already held. The part it
protects is short, so releasing it between pipes only makes proving
correctness more difficult.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with Damien's s/p/pipe/ change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Parts that poke port specific HW blocks like the encoder HW state
readout or connector hotplug detect code need a way to check whether
required power domains are on or enable/disable these. For this purpose
add a set of power domains that refer to the port HW blocks. Get the
proper port power domains during modeset.
For now when requesting the power domain for a DDI port get it for a 4
lane configuration. This can be optimized later to request only the 2
lane power domain, when proper support is added on the VLV PHY side for
this. Atm, the PHY setup code assumes a 4 lane config in all cases.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reading code free of special cases wins over the small overhead of
calling a noop handler. Suggested by Jesse.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split the 'set' power well handler into an 'enable', 'disable' and
'sync_hw' handler. This maps more conveniently to higher level
operations, for example it allows us to push the hsw package c8 handling
into the corresponding hsw/bdw enable/disable handlers and the hsw BIOS
hand-over setting into the hsw/bdw sync_hw handler.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Appease checkpatch's whitespace complaints.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever we request a power domain it has to guarantee that all HW
resources are enabled that are needed to access a HW register associated
with that power domain. In case a register is on an always-on power well
this won't result in turning on a power well, but it may require
enabling some other HW resource. One such resource is the HSW/BDW device
D0 state that is required for all register accesses and thus for all
power wells/power domains.
So far the init power domain (guaranteeing access to all HW registers)
was part of the default i9xx always-on power well, but not the HSW/BDW
always-on power wells. Add the domain to the latter power wells too.
Atm, all the always-on power wells have noop handlers, so this doesn't
change the functionality.
v2:
- clarify semantics of always-on power wells (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These macros are used only locally, so move them to the .c file.
No functional change.
v2:
- add init power domain to always-on power wells in the following
- separate - patch (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions are used only by a single call site and are simple
enough to just fold them in.
Note that in later patches the parts folded in here are further
simplified as we'll remove hsw_{disable,enable}_package_c8 and the NULL
check of the power well enable/disable handlers. All this means that at
the end intel_display_power_get/put() becomes more understandable as we
don't need to jump between two functions when reading the code.
No functional change.
v2:
- clarify the rational for the change (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have two names for the same register CHICKEN_PIPESL_1 and
HSW_PIPE_SLICE_CHICKEN_1. Unify it to just one.
Also rename the FBCQ disable bit to resemble the name we've
given to a similar bit on earlier platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gen7_enable_fbc() may write to some registers which we've already
touched, so use RMW so that we don't undo any previous updates.
Also note that we implemnt WaFbcAsynchFlipDisableFbcQueue:bdw.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Misplaced parens cause us to totally clobber the CHICKEN_PIPESL_1
registers with 0xffffffff. Move the parens to the correct place
to avoid this.
In particular this caused bit 30 of said registers to be set, which
caused the sprite CSC to produce incorrect results.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72220
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Consistency throughout the code base is good and remove some room for
mistakes (as explained in the "drm/i915: Use a pipe variable to cycle
through the pipes" commit)
So, let's replace the for_each_pipe(i) occurences by for_each_pipe(pipe)
when it's reasonable and practical to do so (eg. when there isn't another
pipe variable already).
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec we need to always set this magic bit in ring buffer
mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben and I believe this will be necessary on production hardware.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Shuffle lines to group all ROW_CHICKEN writes and add a
cautious comment that this might not be needed on production hw.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I believe this will be necessary on production hardware.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Fix whitespace fail spotted by checkpatch. Also add missing
:bdw w/a tag that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the addition of dev_priv->mm.busy, there's no more need for
dev_priv->pc8.gpu_idle, so kill it.
Notice that when you remove gpu_idle, hsw_package_c8_gpu_idle and
hsw_package_c8_gpu_busy become identical to hsw_enable_package_c8 and
hsw_disable_package_c8, so just use them.
Also, when we boot the machine, dev_priv->mm.busy initially considers
the machine as idle. This is opposed to dev_priv->pc8.gpu_idle, which
considered it busy. So dev_priv->pc8.disable_count has to be
initalized to 1 now.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got lost when we shuffled around our internal branch and
GEN7_FEATURES macro. There were no HW changes to support FBC, so we just
need to set the flag.
v2: Don't allow FBC for any pipe but A on platforms with DDI. (Paulo)
Cc: Daisy Sun <daisy.sun@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
