Fix docbook problem in SCSI source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The original code would incorrectly hardcode ELS timeout values
rather than using the traditional '2 * r_a_tov' value. In some
cases, the hardcoded values would be larger than the
mailbox-command-timeout and result in a needless BIG_HAMMER (ISP
reset), the typical recovery mechanism employed in such cases.
The second defect in the original code was in the assignment of
the default 'ha->r_a_tov' to twice the traditional value.
Correct this by setting the value to 10 seconds.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For recent ISPs, software must detect OVERRUN conditions by
checking the SS_RESIDUAL_OVER bit during CS_COMPLETE handling.
Update the driver to perform this check, which is consistent with
what earlier firmwares did by explicitly cracking open the
FCP_RSP statuses and returning an CS_DATA_OVERRUN.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's no point in hitting the RISC with what will most
assuredly be an unsucessful reset of the RISC hardware if the
initial stop-firmware mailbox command fails with a time-out
status. Instead, to avoid what could amount to a lengthy
stop-firmware/detect-failure/reset-risc loop, continue with
driver unloading and discard the stop-firmware requirement.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The fix up from Daniel Drake for replacing GFP_DMA with something
more sensible has gone in here:
commit 69e562c234
Author: Daniel Drake <dsd@gentoo.org>
Date: Wed Feb 20 13:29:05 2008 +0000
[SCSI] arcmsr: fix message allocation
add a change log and update the version for this.
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ps3rom does:
scsi_for_each_sg(cmd, sgpnt, scsi_sg_count(cmd), k) {
kaddr = kmap_atomic(sg_page(sgpnt), KM_IRQ0);
We cannot do something like that with the clustering enabled (or we
can use scsi_kmap_atomic_sg).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sg driver rounds up the length in struct scatterlist to be a multiple
of 512 in some conditions. So LLDs can't use the data length in a sg
list to calculate residual. Instead, the length in struct scsi_cmnd
should be used.
[Geert: the variable buflen already contains scsi_bufflen(cmd)]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The phy sas address is showing wrongly (wrong endianness). Fix up the
endian transforms to make this correct.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The recent patch named:
[SCSI] gdth: !use_sg cleanup and use of scsi accessors
has done a bad job in handling internal commands issued by gdth_execute().
Internal commands are issued with device gdth_cmd_str ready made directly
to the card, without any mapping or translations of scsi commands. So here
I added a gdth_cmd_str pointer to the gdth_cmndinfo private structure which
is then copied directly to host.
following this patch is a cleanup that removes the home cooked accessors
and reverts them to regular scsi_cmnd accessors. Since they are not used
anymore. After review maybe the 2 patches should be squashed together.
FIXME: There is still a problem with gdth_get_info(). as reported there
is a WARN_ON trigerd in dma_free_coherent() when doing:
$ cat /proc/sys/gdth/0
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
gdth_exit would first remove all cards then stop the timer
and would not sync with the timer function. This caused a crash
in gdth_timer() when module was unloaded.
So del_timer_sync the timer before we delete the cards.
also the reboot notifier function would crash. So clean
that up and fix the crashes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The old tools did not set max session cmds. This is a regression.
I removed the check when merging the power of 2 patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a particularly nasty bug. The problem is that if any internal
ascb times out, currently we free it even though it's pending at the
sequencer. This results in the sequencer getting terminally confused
and the error message:
BUG:sequencer:dl:no ascb
Being returned when it comes back. The way to fix this is to manage
freeing the ascb from the tasklet completion routine, so that we only
free it when the sequencer actually returns it. The code is also
altered to use on stack completions and transfer variables.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Correct one use after free of the sas task
- update the reset required path to move straight to LUN reset
- make the bigger hammer actually reset something instead of just trying
to clear all the tasks.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Once the phy reset is plumbed in properly, SATA error handling fails
nastily because we change the port attached_sas_address using the WWN
field of the IDENTIFY message. This is a nice thing to do in theory,
but it really destroys hotplug because any event on the port causes an
automatic mismatch between the sas_address the phy just picked up and
the one we propagate into the port. However ugly they are, we have to
stick with the sas addresses made up by the phys and expanders.
Also does a few cosmetic changes to the way port printing is done to
make it clearer how a port is formed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently aic94xx has no exported I_T_nexus_reset function. This is a
bit of a huge problem, since sas_ata relies on this function to
perform an ATA phy reset and also it means that if abort fails, we
really have no bigger hammer to hit everything with.
Plumb in the I_T_nexus_reset by quiescing the sequencer, sending the
correct phy reset (link for ATA and hard for SAS) and then carefully
resuming the sequencer again.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
mvsas.c picked up execute permissions. Move it back to being a plane
old file.
James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adding the same item to a given linked list more than once is guaranteed
to break and corrupt the list. This is however what we do in dmi_scan
since commit 79da472111 ("x86: fix DMI out
of memory problems").
Given that there is absolutely no interest in saving empty OEM strings
anyway, I propose the simple and efficient fix below: we discard the empty
OEM strings altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: drivers/video/built-in.o(.text+0x7c64a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c65d): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c679): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c699): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c69f): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3676): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3689): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36a5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36c5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36cb): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a079a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ad): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07c9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07e9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ef): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
Remove __devinitdata annotation from the variable ypan.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NBD doesn't work well with CFQ (or AS) schedulers, so let's default to
something else.
The two problems I have experienced with nbd and cfq are:
1) nbd hangs with cfq on RHEL 5 (2.6.18) -- this may well have been
fixed
There's a similar debian bug that has been filed as well:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=447638
There have been posts to nbd-general mailing list about problems with
cfq and nbd also.
2) nbd performs about 10% better (the last time I tested) with deadline
vs. cfq (the overhead of cfq doesn't provide much advantage to nbd [not
being a real disk], and you end up going through the I/O scheduler on
the nbd server anyway, so it makes sense that deadline is better with
nbd)
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice. In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the "cmos" RTC, have /proc/driver/rtc say whether HPET based IRQ
emulation is in effect. Given the problems we've had with this particular
hardware maldesign (and the fact that most BIOS code seems not to provide
the IRQ routing needed to use the saner HPET modes), this should help
troubleshooting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface. As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin. (This probably means all
transfers are one bit out of sequence.)
This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity. The fix
assures that the clock mode is properly set before asserting chip select.
This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_spi driver does not initialize clock polarity correctly (except for
at91rm9200 CS0 channel) in some case.
The atmel_spi driver uses gpio-controlled chipselect. OTOH spi clock signal
is controlled by CSRn.CPOL bit, but this register controls clock signal
correctly only in 'real transfer' duration. At the time of cs_activate()
call, CSRn.CPOL will be initialized correctly, but the controller do not know
which channel is to be used next, so clock signal will stay at the inactive
state of last transfer. If clock polarity of new transfer and last transfer
was differ, new transfer will start with wrong clock signal state.
For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be low.
Of course this will violates SPI transfer.
This patch is short term solution for this problem. It makes all CSRn.CPOL
match for the transfer before activating chipselect. For longer term, the
best fix might be to let NPCS0 stay selected permanently in MR and overwrite
CSR0 with to the new slave's settings before asserting CS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: michael <trimarchi@gandalf.sssup.it>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following is a clean up and correction of the copyright holding
entities for the files associated with the intel iommu code.
Signed-off-by: <mgross@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current mainline, __devinit qpti_sbus_probe() still is calling __init
qpti_chain_add(). Change occurrences of __init to __devinit to fix.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert rough draft Marvell 6440 driver to a working driver.
Added support for SAS and SATA devices, hotplug, wide port, and expanders.
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make sure the restoration correctly restores the AR registers by
flipping the ARX register into index mode before doing anything.
Without this, some people have had the text mode restore all green.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current sas_scsi_clear_queue_lu() is wrongly checking for commands
which match the pointer to the one passed in. It should be checking for
commands which are on the same logical unit as the one passed in. Fix
this by checking target pointer and LUN for equality.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The clear nexus I_T and clear nexus I_T_L functions in the aic94xx
specify the SUSPEND_TX flag which causes the sequencer to be suspended
until it receives a RESUME_TX. Unfortunately, nothing ever sends the
resume, so the sequencer on the link is stopped forever, leading to
eventual timeouts and I/O errors.
Since clear nexus commands are only executed as part of error recovery,
it's perfectly fine to keep the sequencer running on the link ... as
soon as the recovery function is completed, we'll send it the commands
to retry.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove the now useless counting of adjacent pages from the debugging code in
to make it compile when DEBUG is set non-zero.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_internal_copy copies an in-kernel buffer to a sg list by using
scsi_kmap_atomic_sg. Some functions calls stex_internal_copy with
sg_count in struct st_ccb, which is the value that dma_map_sg
returned. However it might be shorter than the actual number of sg
entries (if the IOMMU merged the sg entries).
scsi_kmap_atomic_sg doesn't see sg->dma_length so stex_internal_copy
should be called with the actual number of sg entries
(i.e. scsi_sg_count), because if the sg entries were merged,
stex_direct_copy wrongly think that the data length in the sg list is
shorter than the actual length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_direct_copy copies an in-kernel buffer to a sg list in order to
spoof some SCSI commands. stex_direct_copy calls dma_map_sg and then
stex_internal_copy with the value that dma_map_sg returned. It calls
scsi_kmap_atomic_sg to copy data.
scsi_kmap_atomic_sg doesn't see sg->dma_length so if dma_map_sg merges
sg entries, stex_internal_copy gets the smaller number of sg entries
than the acutual number, which means it wrongly think that the data
length in the sg list is shorter than the actual length.
stex_direct_copy shouldn't call dma_map_sg and it doesn't need since
this code path doesn't involve dma transfers. This patch removes
stex_direct_copy and simply calls stex_internal_copy with the actual
number of sg entries.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 3163f725a5 introduced locking in
lpfc_sli_hbqbuf_fill_hbqs, but missed unlocking on one exit.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status. Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
arcmsr_iop_message_xfer() is called from atomic context under the
queuecommand scsi_host_template handler. James Bottomley pointed out
that the current GFP_KERNEL|GFP_DMA flags are wrong: firstly we are in
atomic context, secondly this memory is not used for DMA.
Also removed some unneeded casts.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ioc->name is used in the printk's after ioc has been freed. Free
after prinks to fix this.
This patch fixes two use-after-free's introduced by
commit e78d5b8f1e and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the following needlessly global functions static:
- __iscsi_unblock_session()
- iscsi_session_state_name()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global lpfc_disable_node() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
modules: do not try to add sysfs attributes if !CONFIG_SYSFS
POWERPC: fix typo in pseries/power.c
PM: Remove unbalanced mutex_unlock() from dpm_resume()
UIO: fix Greg's stupid changes
stable_kernel_rules: fix must already be in mainline
ide: mark "ide=reverse" option as obsolete
Driver core: Fix error handling in bus_add_driver().
driver-core: fix kernel-doc function parameters
cpufreq: fix kobject reference count handling
slabinfo: fall back from /sys/kernel/slab to /sys/slab
Fix broken utf-8 encodings in ja_JP translation of stable_kernel_rules.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix wrong reference counter check for proc_dir_entry
PCI: fix up setup-bus.c #ifdef
PCI: don't load acpi_php when acpi is disabled
PCI: quirks: set 'En' bit of MSI Mapping for devices onHT-based nvidia platform
PCI: kernel-doc: fix pci-acpi warning
PCI: irq: patch for Intel ICH10 DeviceID's
PCI: pci_ids: patch for Intel ICH10 DeviceID's
PCI: AMD SATA IDE mode quirk
PCI: drivers/pcmcia/i82092.c: fix up after pci_bus_region changes
PCI: hotplug: acpiphp_ibm: Remove get device information
