Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we release the lane soft reset before lane stagger settings
have been programmed. I believe that means we don't actually do lane
staggering. So move the soft reset deassert to happen after lane
staggering has been programmed.
The one confusing thing in this is that when we remove the power down
override from the lanes, they power up with defaul register values,
which do not have the soft reset overrides enabled. And according to
some docs by default the data lane resets are tied to cmnreset. So that
would mean that lanes would come out of reset without staggering as
soon as the power down overrides are removed. But since we can't access
either the lane stagger register nor the soft reset override registers
until the lanes are powered on, we can't really do anything about it.
So let's just set the soft reset overrides as soon as the lane is
powered on and hope for the best.
v2: Fix typos in commit message (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/intel_dp_tps/drm_dp_tps/.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With DPIO powergating active the DPLL can't be accessed unless
something else is keeping the common lane in the channel on.
That means the PPS kick procedure could fail to enable the PLL.
Power up some data lanes to force the common lane to power up
so that the PLL can be enabled temporarily.
v2: Avoid gcc uninitilized variable warning
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT platform uses live status bits from 0x44440 register to obtain DP
status on hotplug. The existing g4x_digital_port_connected() uses a
different register and hence misses DP hotplug events on BXT
platform. This patch fixes it by using the appropriate register(0x44440)
and live status bits(3:5).
Based on a patch by Durgadoss R <durgadoss.r@intel.com>, from whom the
commit message is shamelessly copy pasted.
Reported-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Choose the right function at the intel_digital_port_connected level.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Choose the right function at the intel_digital_port_connected level.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a common intel_digital_port_connected() that splits out to functions
for different platforms. No functional changes.
v2: make the function return a boolean
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the case added for eDP on port A (always connected from this
function's point of view), we should not be hitting any of the default
cases in ibx_digital_port_connected, so add MISSING_CASE annotation.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should not be hitting any of the default cases in
g4x_digital_port_connected, so add MISSING_CASE annotation and return
boolean status. The current behaviour is just cargo culting from the
days of yonder when the display port support was added to i915.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can be made static there. No functional changes.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs give you the impression that the unique transition scale
value shouldn't matter when unique transition scale is enabled. But
as Imre found on BXT (and I verfied also on BSW) the value does
matter. So from now on just program the same value 0x9a always.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need the link_bw/rate_select parameters when starting link
training, and they should be computed based on the currently active
config, so throw them out from intel_dp and just compute on demand.
Toss in an extra debug print to see rate_select in addition to link_bw,
as the latter may be 0 for eDP 1.4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_dp->link_bw is going away, so consul the port_clock instead when
choosing between TP1 and TP3.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use a separate variable for the TRANS_DP_CTL value instead of reusing
'tmp' that otherwise contains the DP port register value.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.
v2: Fix typo in commit message (Sivakumar)
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().
There should be no functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WA for BXT A0/A1, where DDIB's HPD pin is swapped to DDIA, so enabling
DDIA HPD pin in place of DDIB.
v2: For DP, irq_port is used to determine the encoder instead of
hpd_pin and removing the edp HPD logic because port A HPD is not
present(Imre)
v3: Rebased on top of Imre's patchset for enabling HPD on PORT A.
Added hpd_pin swapping for intel_dp_init_connector, setting encoder
for PORT_A as per the WA in irq_port (Imre)
v4: Dont enable interrupt for edp, also reframe the description (Siva)
v5: Don’t check for PORT_A in intel_ddi_init to update dig_port,
instead avoid setting hpd_pin itself (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 spec TEST_CRC_COUNT is a "4 bit wrap counter which
increments each time the TEST_CRC_x_x are updated."
However if we are trying to verify the screen hasn't changed we get
same (count, crc) pair twice. Without this patch we would return
-ETIMEOUT in this case.
So, if in 6 vblanks the pair (count, crc) hasn't changed we
return it anyway instead of returning error and let test case decide
if it was right or not.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."
However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.
So we face cases like this:
first get_sink_crc operation:
count: 0, crc: 000000000000
count: 1, crc: c101c101c101
returned expected crc: c101c101c101
secont get_sink_crc operation:
count: 1, crc: c101c101c101
count: 0, crc: 000000000000
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
But also the reset to 0 should be faster resulting into:
get_sink_crc operation:
count: 1, crc: c101c101c101
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).
If the pair changed you have your valid CRC.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.
But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BPP bits defined in VBT should be used only on panels whose
edid version is 1.3 or older. EDID version 1.4 introduced offsets
where bpp is defined and read into display_info, hence bpp from
VBT will be used only when bpc in display_info is zero.
v2: use display_info.bpc for deciding when to use vbt_bpp (Jani)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just a preparation patch to make clear what operation we
are performing. There is no functional change on the sink crc
logic.
hsw_disable_ips has been moved a bit further in the start function
to avoid disabling ips when sink crc is not going to be started.
and to avoid goto on this function.
v2: explain why hsw_disable_ips() call place has changed.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we got to the point where we are trying to stop sink CRC
the main output of this function was already gotten properly,
so don't return the error and let userspace use the crc data.
Let's replace the errnos returns with some log messages.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now if we face any kind of error sink crc calculation
stays enabled.
So, let's give a shot and try to stop it anyway if it got enabled.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There's not much point for calculating the changes for the old
state. Instead just disable all scalers when disabling. It's
probably good enough to just disable the crtc_scaler, but just in
case there's a bug disable all scalers.
This means intel_atomic_setup_scalers is only called in the crtc
check function now, so all the transitional code can be removed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull intel drm fixes from Jani Nikula:
"Almost all of it is regression fixes all around, with cc: stable, and
then there's Ander's fix for one of the warnings you reported. We're
still working on the rest"
[ Dave is on vacation, and Jani is heading out on vacation too ]
* tag 'drm-intel-next-fixes-2015-07-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Clear pipe's pll hw state in hsw_dp_set_ddi_pll_sel()
drm/i915: fix backlight after resume on 855gm
agp/intel: Fix typo in needs_ilk_vtd_wa()
drm/i915/ppgtt: Break loop in gen8_ppgtt_clear_range failure path
drm/i915: Fix IPS related flicker
Similarly to what is done for SKL, clear the dpll_hw_state of the pipe
config in hsw_dp_set_ddi_pll_sel(), since it main contain stale values.
That can happen if a crtc that was previously driving an HDMI connector
switches to a DP connector. In that case, the wrpll field was left with
its old value, leading to warnings like the one below:
[drm:check_crtc_state [i915]] *ERROR* mismatch in dpll_hw_state.wrpll (expected 0xb035061f, found 0x00000000)
------------[ cut here ]------------
WARNING: CPU: 1 PID: 767 at drivers/gpu/drm/i915/intel_display.c:12324 check_crtc_state+0x975/0x10b0 [i915]()
pipe state doesn't match!
This regression was indroduced in
commit dd3cd74acf
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 13:34:29 2015 +0300
drm/i915: Don't overwrite (e)DP PLL selection on SKL
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
The current code tracks business across all pipes, but we're only
really interested in the one pipe DRRS is enabled on. Fairly tiny
optimization, but something I noticed while reading the code. But it
might matter a bit when e.g. showing a video or something only on the
external screen, while the panel is kept static.
Also regroup the code slightly: First compute new bitmasks, then take
appropriate actions.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
commit 2c310b9d2859863826c3688c88218d607d5dd19a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon May 18 12:28:52 2015 +0200
drm/i915: Split skl_update_scaler, v4.
It's easier to read separate functions for crtc and plane scaler state.
Changes since v1:
- Update documentation.
Changes since v2:
- Get rid of parameters to skl_update_scaler only used for traces.
This avoids needing to document the other parameters.
Changes since v3:
- Rename scaler_idx to scaler_user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Changes for BXT - added a IS_BROXTON check to use the macro related to PPS
registers for BXT.
BXT does not have PP_DIV register. Making changes to handle this.
Second set of PPS registers have been defined but will be used when VBT
provides a selection between the 2 sets of registers.
v2:
[Jani] Added 2nd set of PPS registers and the macro
Jani's review comments
- remove reference in i915_suspend.c
- Use BXT PP macro
Squashing all PPS related patches into one.
v3: Jani's review comments addressed
- Use pp_ctl instead of pp
- ironlake_get_pp_control() is not required for BXT
- correct the use of && in the print statement
- drop the shift in the print statement
v4: Jani's comments
- modify ironlake_get_pp_control() - dont set unlock key for bxt
v5: Sonika's comments addressed
- check alignment
- move pp_ctrl_reg write (after ironlake_get_pp_control())
to !IS_BROXTON case.
- check before subtracting 1 for t11_t12
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Corrected the documentation on the intel_edp_drrs_flush and
intel_edp_drrs_invalidate.
And accordingly edp_drrs_flush function is modified to restart the idleness
detection after upclocking.
v2: Update kerneldoc
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> (v1)
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BXT supports following intermediate link rates for edp:
2.16GHz, 2.43GHz, 3.24GHz, 4.32GHz.
Adding support for programming the intermediate rates.
v2: Adding clock in bxt_clk_div struct and then look for the entry with
required rate (Ville)
v3: 'clock' has the selected value, no need to use link_bw or rate_select
for selecting pll(Ville)
v4: Make bxt_dp_clk_val const and remove size (Ville)
v5: Rebased
v6: Removed setting of vco while rebasing in v5, adding it back
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Reviewed-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Cc: stable@vger.kernel.org
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The hotplug callbacks for DP and DDI effectively did nothing. Remove
them.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are plenty of hotplug related fields in struct drm_i915_private
scattered all around. Group them under one hotplug struct. Clean up
naming while at it. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
