Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sNVc
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new IIO drivers, cleanups and functionality for the 4.2 cycle.
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
Some sensors like the LIS331DL only support 8bit data by a single
register per axis. These utilize the MSB byte. Make it possible
to register these apropriately.
A oneliner change is needed in the ST sensors core to handle 8bit
reads as this is the first supported 8bit sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PiG+
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.1a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The usual mixed bag of fixes for IIO in the 4.1 cycle.
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wyz7
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, functionality and cleanups for the 4.2 cycle
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
The ST sensors are detected by reading a WhoAmI register and
matching the number found to a sensor name string. To make it
easier to figure out what happens when things go wrong, print
the WhoAmI value and the device name we're trying to match.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not all sensors support BDU (block data update) and in fact a
bunch of the in-kernel sensor settings do not specify the
BDU address field. Make this optional.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some sensors such as magnetometers and pressure sensors doesn't
have interrupts at all, and thus no DRDY setting applies. Make
the assignment of an interrupt optional, and do not call
st_sensors_set_drdy_int_pin() if there is no drdy (data ready)
pin specified.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Print a proper error message if we're missing the trigger
IRQ.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Current API only allows setting one offset in the field. This API
is extended to set multiple offsets in the field report.
Also update parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some hid sensor feature report can contain more than one reports.
This API can now support receiving multiple values from the feature
report.
Also update the parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If CONFIG_PM_SLEEP=n:
drivers/iio/common/ssp_sensors/ssp_dev.c:644: warning: ‘ssp_suspend’ defined but not used
drivers/iio/common/ssp_sensors/ssp_dev.c:669: warning: ‘ssp_resume’ defined but not used
Protect the unused functions by #ifdef CONFIG_PM_SLEEP to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Also change to div64_u64 in one place to avoid loss of precision
(was dividing a 32 bit number by a 64 bit number, but casting this
to 64 bit divided by 32 bit) Those divide functions certainly have
esoteric naming!
Fixes warnings with asm-generic/div64.h do_div such as:
In file included from drivers/iio/common/ssp_sensors/ssp_iio.c:20:0:
drivers/iio/common/ssp_sensors/ssp_iio_sensor.h: In function 'ssp_convert_to_freq':
>> drivers/iio/common/ssp_sensors/ssp_iio_sensor.h:56:16: warning: comparison of distinct pointer types lacks a cast [enabled by default]
drivers/iio/common/ssp_sensors/ssp_iio_sensor.h:56:2: warning: right shift count >= width of type [enabled by default]
>> drivers/iio/common/ssp_sensors/ssp_iio_sensor.h:56:2: warning: passing argument 1 of '__div64_32' from incompatible pointer type [enabled by default]
include/asm-generic/div64.h:35:17: note: expected 'uint64_t *' but argument is of type 'int *'
drivers/iio/common/ssp_sensors/ssp_iio.c: In function 'ssp_common_process_data':
include/linux/iio/buffer.h:142:32: warning: 'calculated_time' may be used uninitialized in this function [-Wuninitialized]
drivers/iio/common/ssp_sensors/ssp_iio.c:83:10: note: 'calculated_time' was declared here
Fixed by using straight coded version as per the description in the
div64.h header, thus ensuring no issue with 32 bit integers.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds common library for sensorhub iio drivers.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sensorhub is MCU dedicated to collect data and manage several sensors.
Sensorhub is a spi device which provides a layer for IIO devices. It provides
some data parsing and common mechanism for sensorhub sensors.
Adds common sensorhub library for sensorhub driver and iio drivers
which uses sensorhub MCU to communicate with sensors.
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
To improvement power and performance, both regular and run time callbacks
are introduced. Because of auto suspend delay, two consecutive read
don't have to go through full power on/off procedure. The auto suspend
time can be adjusted using regular power attributes of PM sysfs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUWnZBAAoJEFSFNJnE9BaIZAAQAJpkot0ZAYPwtIkmtV1JqrLQ
EZRkBN+cIf3q5zp/TnQTqfyhKbpHbJ9/Pnb0zHvn7Yh3WpZod2tyoC3xb8JAlX2h
3tJRrA7plkdMjtwO/ryOxrVJYrm6rCeqKpciwMpDf4E/4fhU5CU++TpmWbhn04qB
7PEZJN5dkmdnQYSIyNle11MYN+NpCAB4zqDvRJoJHpqZV6zAqygJy03H1PqXFS/S
iNBL3jS8/PTbeUURUFOQTiqnJw5KuDke7OoXxUfvCpUwQfNLD8mOTrVrEoId1cM0
Y2fmasfHteh83KP34/MOTwNA3EezM8iQOMzJnXtOpxpySPDrDSP68FDAJs15TUJm
je8E1xxxdjOWuzgSd9djNm9qhlBkoYgbRwzc8wSAHMK7mCV7pP485WZk5E8rRX2z
gMFgUmu4LkiZ2V9glGTAcHqnjhLNDTRCp1Nl/sMVgssFBBNjgR5+nZjUFqDR2QpD
eo4ReIzev7Rzxe2lACRjnRrCnO+KKcjiDkyCdM3X2zdTddQRVrP5Uz+jgnvGAeMO
hCYDHSOiMzV/r5emVfmNG9w8P9a6rZqu4KqcM/KjSzAfHFQTqmfr4Tkfn/hbeUjY
h/zzB18EM4kUSxm3E6+CbFRWcfC7b/PLcUOwSitdujb9cYaX72gdesO2/P3jNFAK
2bjoLRr5l4M4n/DeHae4
=BDOo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, features and cleanups for IIO in the 3.19 cycle.
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUPWESAAoJEFSFNJnE9BaI/TAP/2EZp7NR+k3CRZVRLuXxeSrD
voMS3zNtYMC2E56W0l89gOZdR4rCXzJlhUdRHcGkl7qw1r6stjEBMKIJmd3NVEc4
dOZ4tCsb/kTmF+66QitL73ioZqoLMrpaGubf8l10t8V3wSsOqnf3wYUftGcdl4NK
uXAIDmUYgAm4zUUZCKE95o2Npkotm5ftRQqgdChuK7vGVJikN8blzRDokGcZTAh6
CR04tktxhkg/E+Nq67h9zXPnMOTbw4onNGKD3cztGKZ2bBN+4W/ywEnUrTOu35Eg
zKMkwYnlBKMTOkTwzml4izHlZw/yFXTXHSPwm1a2fxcVuLuGUBuxX5Pa+kCpLOJo
2aewUhnwlXhvCrDcFq/rTeqUsOV8mfZxuxqVOQ/utbyUgX5LtHCgQ8aPf0GBbty7
l8SzxTkCXyogUc4PbNh8DqqksKGkMn/AtC3MfWeEvAYdCZpMXROb4RTAAMVvqytl
34DMKVaRUy8eiUfcJ+8cH9LvH3Gri7OIbXeLD7iatZ7anaXlQB/EzjTc8yw7+t+C
EBa7s90XhbRCkE5cadZm76deSscyGgX1cCQS6eStzn1AF0LY/Cj1KMkkJjtFFN31
Cc7SOAa7rY0BwotwVRV5id4tihyxU9b/Dxi1StoioP4Rjp0B3Y9WsN+EuvPGjFYo
4JrfV0JYhHktQF+rEmM0
=TYUO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.18 cycle.
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
Use byte_for_channel as iterator to properly initialize the buffer.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: <Stable@vger.kernel.org>
This patch change structure name and related variables names.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in there, and it resolves a merge issue with
drivers/iio/accel/bma180.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value from st_sensors_set_drdy_int_pin() is assigned to err here,
but that stored value is not used before it is overwritten. To fix
this we're enforcing a check on st_sensors_set_drdy_int_pin()'s
return value and if it's an error, we're returning right away.
Cc: jic23@kernel.org
Cc: linux-iio@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
The I2C devices that make up the STMicroelectronics MEMS sensors
may be sneakily enabled by cleverly giving the device node the same
name as a string match from the platform device ID table. However
the right method is to use the compatible string.
On detection, the ST sensors use the ID string to probe and
instatiate the right sensor driver, so pass the kernel-internal ID
string in the .data field of the OF match table, and set the I2C
client name to this name when a compatible match is used.
This avoids having misc Linux-specific strings floating around in
the device tree.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following sparse warning:
CHECK drivers/iio/common/hid-sensors/hid-sensor-attributes.c
drivers/iio/common/hid-sensors/hid-sensor-attributes.c:346:5: warning:
symbol 'hid_sensor_get_reporting_interval' was not declared. Should it be static?
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the STMicroelectronics sensors only support one single
platform data item: configuration of the DRDY (data ready) pin
for a particular design. Augment the core to prioritize and take
this information from the device tree if the parent device has an
assigned device node, else fall back to passed in platform data
(usually the default data).
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows in kernel client drivers to access this
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Move the 'static' keyword to beginning of definition to silence the
following compilation warning:
drivers/iio/common/hid-sensors/hid-sensor-attributes.c:34:1: warning: ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RuB2
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 3.16 cycle.
A mixed bag of fixes, many of which feel just to late for 3.15.
* hid sensors - some devices need a feature report request in order to
change power state. This isn't part of the spec, but has been observed
on several devices and does no harm to others.
* mpl3115 has had two errors in the buffer description fixed. The presure is
signed, not unsigned and the temperature has 12 bits rather than 16.
These could lead to incorrect interpretation of the data in userspace.
* tsl2x7x - the high byte of the proximity thresholds should be written along
with the low byte (which was). This could lead to interesting results
with large thresholds.
* twl4030 - a flag to specify processed values were required was not set
when initializing a reading. As such values returned were in an unknown
state. Fixed by simply initializing it appropriately.
* IIO_SIMPLE_DUMMY_BUFFER did not select IIO_BUFFER leading to randconfig
build errors.
* ak8975 was applying an unwanted le16_to_cpu conversion as the i2c framework
already performs one. As such for big endian systems, the bytes would be
in the wrong order in the magnetic field measurements reported.
* mxs-lradc - the controllable voltage dividers were not enabled / disabled for
later channels than the first one during conversion.
* at91_adc error handling returned -ENOMEM in a u8. Return value of
at91_adc_get_trigger_value_by_name changed to int thus allowing -ENOMEM and
also original values to be returned.
* mcb - mcb_request_mem returns and ERR_PTR but the caller was checking for
NULL to detect an error.
Some sensor hubs require a get feature report call to be issued soon after
changing the power state of the sensor. Without this, the sensor remains in
the current state. This patch adds a call soon after the power state.
This is retained as a generic call across all sensor hubs since the behavior
has been noticed on more than one implementation.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For PROP_REPORT_INTERVAL, the spec does not mandate the presence
of the report interval unit in the feature report and expects the
default unit of measure to be used as milliseconds.
Currently, when the unit is not present, it gets set as zero leading
to issues in sampling frequency.
This patch sets the unit of measure to the default unit if it
is not defined by firmware.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The "i < " was missing in this condition.
Fixes: 5d02edfc39 ('iio: hid-sensors: Convert units and exponent')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added an API to allow client drivers to turn ON and OFF sensors for
quick read. Added data_read as counting varaible instead of boolean,
so that sensor is powered off only when last user released it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added interface to get poll value in milli-seconds. This value is
changed by changing sampling frequency. This API allows clients
to wait for at least some poll milli seconds before reading a new sample.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hub specify a default unit and alternative units. This
along with unit exponent can be used adjust scale. This change
change HID sensor data units to IIO defined units for each
sensor type. So in this way user space can use a simply use:
"(data + offset) * scale" to get final result.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* AS3935 Lightning Sensor
* MCP3426/7/8 support added to the existing MCP3422 ADC driver
* AK8963 support in the AK8975 driver
* MPU6500 support in the MPU6050 driver (the functionality that is different
is mostly not supported yet in either part).
Staging Graduations
* AD799x ADC
New functionality
* ACPI enumeration for the ak8975 driver
Cleanup / tweaks
* Use snprintf as a matter of good practice in a few additional places.
* Document *_mean_raw attributes. These have been there a while, but were
undocumented.
* Add an in kernel interface to get the mean values.
* Bug in the length of the event info mask that by coincidence wasn't yet
actually causing any problems.
* itg3000 drop an unreachable return statement.
* spear_adc cleanups (heading for a staging graduation but a few more
issues showed up in the review of these patches).
* Exynos ADC dependencies changed so it is only built when Exynos is present
or COMPILE_TEST and OF are set.
* tsl2583 cleanups.
* Some cut and paste typos in the comments of various drivers still in staging.
* Couple of minor improvements to the ST sensor drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=eqGz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new driver, functionality and cleanups for the 3.16 cycle.
New device support
* AS3935 Lightning Sensor
* MCP3426/7/8 support added to the existing MCP3422 ADC driver
* AK8963 support in the AK8975 driver
* MPU6500 support in the MPU6050 driver (the functionality that is different
is mostly not supported yet in either part).
Staging Graduations
* AD799x ADC
New functionality
* ACPI enumeration for the ak8975 driver
Cleanup / tweaks
* Use snprintf as a matter of good practice in a few additional places.
* Document *_mean_raw attributes. These have been there a while, but were
undocumented.
* Add an in kernel interface to get the mean values.
* Bug in the length of the event info mask that by coincidence wasn't yet
actually causing any problems.
* itg3000 drop an unreachable return statement.
* spear_adc cleanups (heading for a staging graduation but a few more
issues showed up in the review of these patches).
* Exynos ADC dependencies changed so it is only built when Exynos is present
or COMPILE_TEST and OF are set.
* tsl2583 cleanups.
* Some cut and paste typos in the comments of various drivers still in staging.
* Couple of minor improvements to the ST sensor drivers.
Currently the pressure sensor has code to retrieve and enable two
regulators for Vdd and Vdd IO, but actually these voltage inputs
are found on all of these ST sensors, so move the regulator
handling to the core and make sure all the ST sensors call these
functions on probe() and remove() to enable/disable power.
Here also mover over to obtaining the regulator from the *parent*
device of the IIO device, as the IIO device is created on-the-fly
in this very subsystem it very unlikely evert have any regulators
attached to it whatsoever. It is much more likely that the parent
is a platform device, possibly instantiated from a device tree,
which in turn have Vdd and Vdd IO supplied assigned to it.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove the hard coded indexes, instead search for usage id and
use the index to set the power and report state.
This will fix issue, where the report descriptor doesn't contain
the full list of possible selector for power and report state.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We can't store the trigger instance created by iio_trigger_alloc, in
trig field of iio_device structure. This needs to be stored in the
driver private data. Othewise it can result in crash during module
unload. Hence created a trig_ptr in the common data structure
for each HID sensor IIO driver and storing here.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Call hid_sensor_hub_device_open when user space opens device and call
hid_sensor_hub_device_close when device is closed. This helps in
saving power.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Strip out all those unnecessary gotos and just return the error right away.
Aids to simplicity and reduces code.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
