Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit adds an empty of_find_node_by_name() function for !CONFIG_OF
builds.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl-core has API to get the boot time configured HFCLK rate which has the
same rate as the audio MCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CFG_BOOT register's HFCLK_FREQ field hold information about the used HFCLK
frequency.
Add possibility for users to get the configured rate based on this
register.
This register was configured during boot, without it the chip would not
operate correctly, so we can trust on this information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To facilitate the device tree support the probe function need to be rearanged.
Small cleanup in the APLL frequency selection part as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To clean up the module probe and remove functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Place the MODULE_* lines in the same block and add MODULE_DESCRIPTION.
Rearange the platform_driver structure at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Original author: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the omap-pcm to use dmaengine.
Certain features are not supported by after dmaengine conversion:
1. No period wakeup mode
DMA engine has no way to communicate this information through
standard channels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the dma_data for the stream (snd_soc_dai_set_dma_data) at dai_startup
time so omap-pcm will have access to the needed information regarding to
the DMA channel earlier.
This is needed for the clean dmaengine support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of the OMAP DMA data type definition the data_type will be used to
specify the number of bits the DMA word should be configured or 0 in case
when based on the stream's format the omap-pcm can decide the needed DMA
word size.
This feature is needed for the omap-hdmi where the sDMA need to be
configured for 32bit word type regardless of the audio format used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
omap-pcm can figure out the correct dma_type based on the stream's format.
In this way we can get rid of the plat/dma.h include from these drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get the needed resources in a correct way and avoid using defines for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To help the driver to get the correct memory range to access McPDM
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on the format of the stream the omap-pcm can decide alone what data
type should be used with by the sDMA.
Keep the possibility for OMAP dai drivers to tell omap-pcm if they want to
use different data type. This is needed for the omap-hdmi for example which
needs 32bit data type even if the stream format is S16_LE.
The check if (dma_data->data_type) is safe at the moment since omap-pcm
does not support 8bit samples (OMAP_DMA_DATA_TYPE_S8 == 0x00).
The next step is to redefine the meaning of dma_data->data_type to unblock
this limitation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The omap-pcm platform driver no longer needs this parameter to select
between ELEMENT and PACKET mode. The selection is based on the configured
packet_size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we only have element or packet synchronization we can use the
dma_data->packet_size to select the desired mode:
if packet_size is 0 we use ELEMENT mode
if packet_size is not 0 we use PACKET mode for sDMA synchronization.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When McBSP is configured in threshold mode we can use sDMA packet mode in
all cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When requested (DMA_PREP_INTERRUPT is cleared in flags) disable all DMA
interrupts for the channel. In this mode user space does not expect
periodic reports from kernel about the progress of the audio stream.
PulseAudio for example support this type of mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the parameter list of device_prep_dma_cyclic() so the DMA drivers
can receive the flags coming from clients.
This feature can be used during audio operation to disable all audio
related interrupts when the DMA_PREP_INTERRUPT is cleared from the flags.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The audio stack used omap_stop_dma/omap_start_dma to pause/resume the DMA.
This method has been used for years on OMAP based products.
We only allow pause/resume when the DMA has been configured in cyclic mode
which is used by the audio stack.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When src_maxburst/dst_maxburst is set to 0 by the users of cyclic DMA
(mostly audio) indicates that we should configure the omap DMA to element
sync mode instead of packet mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mpc5200-psc-ac97 driver does not enumerate attached ac97 devices, so
register the device here.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert pcm030-audio-fabric to use the new snd_soc_register_card api
instead of the older method of registering a separate platform device.
Create the dai_link to the mpc5200_psc_ac97 platform using the device tree.
Convert the pcm030-audio-fabric driver to a platform-driver and add a
remove function.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mpc52xx socs do not define FSL_SOC but need SND_POWERPC_SOC defined to build
ASoC drivers.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DAPM mapping for stream events and give unique names for the streams.
This change also fixes the following warning:
twl6040-codec twl6040-codec: Failed to create Capture debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DAPM mapping for stream events and give unique names for the streams.
This change also fixes the following warning:
twl4030-codec twl4030-codec: Failed to create Capture debugfs file
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested with LPIB delay without any issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DMA Position in Buffer (DPIB) should be used for
ring buffer management, while LPIB register provides
information on the number of samples transfered on
the link. The difference between the two pieces of
information corresponds to hardware/DMA buffering.
This patch reports this difference in runtime->delay, and
removes the use of the COMBO mode on recent Intel hardware.
Credits to Takashi Iwai for an initial patch.
[rebased to for-next branch and replaced snd_printk() with
snd_printdd() by tiwai]
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SSYNC bits are typically used to start multiple
streams synchronously. It makes sense to use them
for a single stream for a more predictable startup
sequence. The transfers only start once the DMA and
FIFOs are ready. This results in a better correlation
between timestamps and number of samples played.
Credits to Kar Leong Wang for suggesting this
improvement.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If headphone jack can't detect plug presence, and we have the jack in
the jack table, snd_hda_jack_detect will return the plug as always
present (as it'll be considered as a phantom jack). The problem is that
when this happens, line out pins will always be disabled, resulting in
no sound if there are no headphones connected.
This was reported as a no sound problem after suspend on
http://bugs.launchpad.net/bugs/1052499, since the bug doesn't manifests
on first initialization before the phantom jack is added, but on resume
we reexecute the initialization code, and via_hp_automute starts
reporting HP always present with the jack now on the table.
BugLink: https://bugs.launchpad.net/bugs/1052499
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: <stable@vger.kernel.org> [v3.6+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 'dres' field (discharge resistance for headphone outputs) is no longer
used in the driver, so remove it.
It was used in the original version of the driver when entering standby
from off, but we stopped using it when we switched from having a single
startup sequence to having separate cap and capless sequences.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On the Thinkpad W520 - and probably several other machines with
Conexant 506x chips - the Dock Mic and Mic are connected to the
same two selector nodes. This patch will make Dock Mic take one
selector node and Mic take the other, when possible.
Without the patch, both paths would take the first selector,
leading to the normal Mic's volume being controlled by
"Dock Mic Boost".
(On other machines, this could instead fixup similar problems between
Mic and Line In, for example.)
BugLink: https://bugs.launchpad.net/bugs/1037642
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While going through Ubuntu bugs, I discovered this patch being
posted and a confirmation that the patch works as expected.
Finding out how the hw volume really works would be preferrable
to just disabling the broken one, but this would be better than
nothing.
Credit: sndfnsdfin (qawsnews)
BugLink: https://bugs.launchpad.net/bugs/559939
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here we add the required documentation for the new Device Tree
bindings pertaining to the MSP CPU-side DAI Driver.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we add the required documentation for the new Device Tree
bindings pertaining to the MOP500 Audio Machine driver.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Includes removal of duplicate debug print affirming entry into
the probe function, an unnecessary line break of a coding line
<80 chars and a white space change (unintentional tab).
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We continue to allow the AB8500 CODEC to be registered via the AB8500
Multi Functional Device API, only this time we extract its configuration
from the Device Tree binary.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Register both parts of the MSP driver from Device Tree so that they
are probed when Device Tree is enabled. Also, as there is platform
data involved, we ensure that there is allocated memory to place the
configuration into and that the correct information is extracted from
the DT binary.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we ensure that the MOP500 audio driver will be probed during a
Device Tree boot. We also parse the sound node to link together the
codec, dma and the CPU-side Digital Audio Interface.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the initial submission of the MSP driver msp1 and msp3's associated
pinctrl mechanism was passed back to platform code using a plat_init()
call-back routine, but it has no place in platform code. The MSP driver
should set this up for the appropriate ports. Instead we use a use_pinctrl
identifier which is passed from platform_data/Device Tree which indicates
which ports should use pinctrl.
Acked-by: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The standard name (and what PulseAudio picks up) is "Dock Mic",
not "Docking Mic" or "Docking-Station".
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for USB suspend breakage moved the code to set up EP
from hw_params to prepare, but it means also the EP setup might be
called multiple times unnecessarily because the prepare callback can
be called multiple times without starting the stream (e.g. OSS
emulation).
This patch adds a new flag to struct snd_usb_substream indicating
whether the setup of EP is required, and do it only when necessary,
i.e. right after hw_params or suspend.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move interface and endpoint configuration from hw_params to prepare
callback. During system suspend/resume when the USB device power isn't
cycled the interface and endpoint configuration need to be set before
audio playback can continue. Resume involves another call to prepare
but not to hw_params, moving it here allows a playing stream to continue
after resume.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the interface to configure an endpoint so that it doesn't require
a hw_params struct. This will allow it to be called from prepare
instead of hw_params, configuring it after system resume.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the peiod_bytes member of snd_usb_substream. It was no longer being
set, but will be needed to resume properly in a future commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is more idiomatic as it means we verify that the device is there
prior to trying to do the card probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the LRCLK is shared and the WM8960 is clock master then we should
enable the LRCM bit to tell the device that it should drive LRCLK when
either ADC or DAC is enabled rather than separately driving the two
LRCLKs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
