Convert the convert the new infrastructure added by previous
patches to actually use the new RX descriptor layout.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when creating a new vif in monitor mode the driver doesn't
allocate a specific station. This causes that in the situation that
tx traffic is injected, the tx queues are not scheduled,
with the result of a TFD queue hang.
Fix that by allocating a station and ensuring its tx queues
are scheduled.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=104591
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
RFC4862 states that "In all cases, a node MUST NOT respond to
a Neighbor Solicitation for a tentative address".
Currently the driver configures the NS offload and does not wait
for address to become permanent, thus violating the RFC.
Just removing the address from the address list is not good enough
for all cases, since the NS messages are needed for the duplicate
address detection and should not be discarded.
For d0i3 disable NS offload. Put tentative address in the address
list so the NS packet will not be filtered out by ucode.
For D3 the platform will not wake from NS packets - so enable
NS offload while removing the tentative address from the list.
Given that now NS offload might be disabled, and that the ucode
uses the IP data for other puroposes (L3 filtering) add two
independent flags indicating if IPv4\IPv6 data is valid.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d0i3_mode variable is used to distinguish between transports that
handle d0i3 entry during suspend by themselves (i.e. the slave
transports) and those which rely on the op_mode layer to do it. The
reason why the former do it by themselves is that they need to
transition from d0i3 in runtime_suspend into d0i3 in system-wide
suspend and this transition needs to happen before the op_mode's
suspend flow is called.
The wowlan_d0i3 element is also a bit confusing, because it just
reflects the wowlan->any value for the trans to understand. This is a
bit unclear in the code and not generic enough for future use.
To make it clearer and to generalize the platform power mode settings,
introduce two variables to indicate the platform power management
modes used by the transport.
Additionally, in order not to take too big a step in one patch, treat
this new variables semantically in the same way as the old d0i3_mode
element, introducing a iwl_mvm_enter_d0i3_on_suspend() function to
help with that.
This commit also adds the foundation for a new concept where the
firmware configuration state (i.e. D0, D3 or D0i3) is abstracted from
the platform PM mode we are in (i.e. runtime suspend or system-wide
suspend).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
d0i3 commands are not supported in the init image, so take
a reference to ensure we don't enter d0i3 during init image,
and additional checks to prevent d0i3 commands when no
fw image is loaded.
Add a few WARN_ON_ONCE to the d0i3 enter/exit commands
to ensure we send d0i3 commands only when the normal
ucode is loaded.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change scan configuration (dwell time, suspend time etc.) according
to traffic conditions. This is useful for scans that are managed by
the FW (e.g. scheduled scan).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to reuse the key update logic for d0i3
as well.
Add some parameters to deal with the constraints
implied by the d0i3 flow (specifically, support
non-SYNC commands, and don't take mutexes that
might deadlock).
Change some commands to be ASYNC, in order
to simplify locking a bit.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d0i3_mode element is never set to IWL_D0I3_OFF, so it's not
necessary to check it in iwl_mvm_is_d0i3_supported().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a potential race condition when entering suspend with d0i3 in
PCIe. If there is a frame queued just before we suspend, it won't
complete and we will never clear the queue stuck timer. To solve
this, call TX_PATH_FLUSH to flush all queues (except the command
queue) as part of the d0i3 entry process. Add a new function that
returns all the flushable queues.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure. Remove it.
Fixes: dbb04b0d29 ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d0i3 flag in the device configuration structure is redundant,
because the same information can be determined by checking the
firmware capability flag.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware debug trigger ID is always a compile-time constant,
so we can use a build-time assertion to validate that it is in
fact a valid constant.
To make that really guaranteed to work, convert this and the
inline function iwl_fw_dbg_trigger_simple_stop() to macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When there's a bt-wifi contention that requires arbitration,
we use a priority-based mechanism to decide which comm wins.
Over time, use cases become more and more complex, with multiple
concurrent active links with different traffic types and different QoS
requirements, on both WiFi and BT sides.
This, in turn, requires us to elaborate our prioritization mechanism.
However, our legacy products included hw that does not supports this,
so selectively enable this on specific hw - as signaled by the firmware.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the FW to use fragmented scan when the traffic load is high
or low latency traffic is on. This is useful for scans that are
managed by the FW (e.g. scheduled scan).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
