If any faulty application issues an NVMe Encapsulated commands to HBA which
doesn't support NVMe protocol then driver should return the command as
invalid with the following message.
"HBA doesn't support NVMe. Rejecting NVMe Encapsulated request."
Otherwise below page fault kernel panic will be observed while building the
PRPs as there is no PRP pools allocated for the HBA which doesn't support
NVMe drives.
RIP: 0010:_base_build_nvme_prp+0x3b/0xf0 [mpt3sas]
Call Trace:
_ctl_do_mpt_command+0x931/0x1120 [mpt3sas]
_ctl_ioctl_main.isra.11+0xa28/0x11e0 [mpt3sas]
? prepare_to_wait+0xb0/0xb0
? tty_ldisc_deref+0x16/0x20
_ctl_ioctl+0x1a/0x20 [mpt3sas]
do_vfs_ioctl+0xaa/0x620
? vfs_read+0x117/0x140
ksys_ioctl+0x67/0x90
__x64_sys_ioctl+0x1a/0x20
do_syscall_64+0x60/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
[mkp: tweaked error string]
Link: https://lore.kernel.org/r/1568379890-18347-12-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The firmware image layout has been changed for Aero controllers. All
compatible HBAs have to get Firmware Package version from Component Image
Header layout.
The Signature field in FW header is set to 0xEB000042 for products
compatible with Component Image Header.
For compatible controllers, driver fetches firmware package version from
ApplicationSpecific field of Component Image Header.
Link: https://lore.kernel.org/r/1568379890-18347-11-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added a new status flag named MPT3_DIAG_BUFFER_IS_APP_OWNED and it will set
whenever application registers the diag buffer & it will be cleared when
application unregisters the buffer.
When this flag is enabled, and if application issues diag buffer register
command without releasing the buffer, then register command will be failed
with -EINVAL status by saying that this buffer is already registered by the
application.
When user issues a trace buffer register command through sysfs parameter,
and if trace buffer is in released stated but not yet unregistered by the
application which was owning it, then driver will unregister the buffer by
itself and freshly register the 1MB sized trace buffer with the HBA
firmware.
Link: https://lore.kernel.org/r/1568379890-18347-9-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The diag buffer which is allocated during driver load time or through sysfs
parameter is marked as driver allocated diag buffer.
MPT3_DIAG_BUFFER_IS_DRIVER_ALLOCATED bit will be set for this buffer.
This buffer won't be de-allocated even when application issues unregister
command, driver just clears the registered status bit. Same buffer will be
reused while re-registering the same diag buffer type by any application.
While re-registering the same diag buffer type application has to register
with the same size that the buffer was allocated during driver load
time. This buffer size can be read by the application by issuing diag
'query' command.
This always makes sure that the memory is available for applications for
collecting the firmware logs. Only thing is that this won't allow the
application to re-register the diag buffer with different size, but the
buffer size which is allocated during driver load time will be enough for
most of the cases for collecting the firmware logs.
Link: https://lore.kernel.org/r/1568379890-18347-8-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clear MPT3_DIAG_BUFFER_IS_RELEASED bit once diag buffer is re-registered
after reading the buffer, else driver won't release the buffer and return
the 'diag release' command with -EINVAL status saying that buffer is
already released.
Link: https://lore.kernel.org/r/1568379890-18347-7-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Application A has registered a diag buffer and looking for particular event
to happen to release & read the trace buffer. Meanwhile application B has
unregistered the diag buffer and now Application A can't get the required
diag buffer. So proper diag buffer ownership is missing.
Each application has to maintain its own Unique ID. Now driver has to save
the Application's UniqueID for each diag buffer type when diag buffer is
registered. And driver has to allow 'release', 'read' & 'unregister' diag
commands only if application's UniqueID matches with saved UniqueID for the
corresponding diag buffer type.
When diag buffer is registered by the driver, then the UniqueID saved by
the driver is "BRCM" (i.e. 0x4252434D) for SAS3 and above generations HBA
devices. For SAS2 HBAs, driver keeps the legacy UniqueID 0x07075900 for
maintaining compatibility with the legacy SAS2 application and this
improvement won't be applicable for SAS2 HBA devices.
Any application can own the buffer registered by the driver by sending
diag register request to driver with same buffer type and size
(Application can get the buffer size by sending 'query' command). Then
driver changes the ownership of the buffer by saving application's
UniqueID for that corresponding buffer type.
Also, application can re-register the diag buffer with same size without
un-registering it, but diag buffer should be released before re-registering
it. By allowing this, driver no need to deallocate and allocate a new
buffer for re-register command, same buffer can be re-used.
Link: https://lore.kernel.org/r/1568379890-18347-6-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Memory leak can happen when diag buffer is released but not unregistered
(where buffer is deallocated) by the user. During module unload time driver
is not deallocating the buffer if the buffer is in released state.
Deallocate the diag buffer during module unload time without any diag
buffer status checks.
Link: https://lore.kernel.org/r/1568379890-18347-5-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display message before releasing the diag buffer so that user knows which
event caused the release of diag buffer.
Releasing of diag buffer means HBA firmware stops posting the firmware logs
on the registered diag buffer.
Link: https://lore.kernel.org/r/1568379890-18347-3-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if user wishes to enable the host trace buffer during driver load
time, then user has to load the driver with module parameter
'diag_buffer_enable' set to one.
Alternatively now the user can enable host trace buffer by enabling the
following fields in manufacturing page11 in NVDATA (nvdata xml is used
while building HBA firmware image):
* HostTraceBufferMaxSizeKB - Maximum trace buffer size in KB that host can
allocate,
* HostTraceBufferMinSizeKB - Minimum trace buffer size in KB atleast host
should allocate,
* HostTraceBufferDecrementSizeKB - size by which host can reduce from
buffer size and retry the buffer allocation
when buffer allocation failed with previous
calculated buffer size.
The driver will register the trace buffer automatically without any module
parameter during boot time when above fields are enabled in manufacturing
page11 in HBA firmware.
Driver follows the following algorithm for enabling the host trace buffer
during driver load time:
* If user has loaded the driver with module parameter 'diag_buffer_enable'
set to one, then driver allocates 2MB buffer and registers this buffer
with HBA firmware for capturing the firmware trace logs.
* Else driver reads manufacture page11 data and checks whether
HostTraceBufferMaxSizeKB filed is zero or not?
- If HostTraceBufferMaxSizeKB is non-zero then driver tries to allocate
HostTraceBufferMaxSizeKB size of memory. If the buffer allocation is
successful, then it will register this buffer with HBA firmware, else
in a loop the driver will try again by reducing the current buffer size
with HostTraceBufferDecrementSizeKB size until memory allocation is
successful or buffer size falls below HostTraceBufferMinSizeKB. If the
memory allocation is successful, then the buffer will be registered
with the firmware. Else, if the buffer size falls below the
HostTraceBufferMinSizeKB, then driver won't register trace buffer with
HBA firmware.
- If HostTraceBufferMaxSizeKB is zero, then driver won't register trace
buffer with HBA firmware.
Link: https://lore.kernel.org/r/1568379890-18347-2-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Local variable fcp_txcmplq_cnt is initialized to 0 and then displayed in
lpfc driver message 0387.
Presumed residual (or unused) code from previous commit.
Removed fcp_txcmplq_cnt.
Link: https://lore.kernel.org/r/20190922035906.10977-20-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
T10 PI support on SLI-4-based FCoE adapters is not supported. A prior
commit in the 12.4.0.0 stream added device recognition that would prevent
T10 PI enablement. However, it didn't contain a complete device list. Thus
some SLI-4 FCoE adapters still had T10 PI enabled.
Fix by expanding the device list that identifies FCoE devices.
Link: https://lore.kernel.org/r/20190922035906.10977-19-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch updates ACQE handling for:
- an EEPROM failure error reported by the adapter.
- ensures that all data for any ACQE, recognized or not, is logged.
- Given that all data is now logged unconditionally, the default case
(unrecognized) data can be reduced.
Link: https://lore.kernel.org/r/20190922035906.10977-18-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In lpfc_release_io_buf, an lpfc_io_buf is returned to the 'available' pool
before any associated sgl or cmd and rsp buffers are returned via their
respective 'put' routines. If xri rebalancing occurs and an lpfc_io_buf
structure is reused quickly, there may be a race condition between release
of old and association of new resources.
Re-ordered lpfc_release_io_buf to release sgl and cmd/rsp
buffer lists before releasing the lpfc_io_buf structure for re-use.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-17-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many of the sgl-per-hdwq paths are locking with spin_lock_irq() and
spin_unlock_irq() and may unwittingly raising irq when it shouldn't. Hard
deadlocks were seen around lpfc_scsi_prep_cmnd().
Fix by converting the locks to irqsave/irqrestore.
Fixes: d79c9e9d4b ("scsi: lpfc: Support dynamic unbounded SGL lists on G7 hardware.")
Link: https://lore.kernel.org/r/20190922035906.10977-16-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing the CT behavior, issues with spinlock_irq were seen. The
driver should be using spinlock_irqsave/irqrestore in the els flush
routine.
Changed to spinlock_irqsave/irqrestore.
Link: https://lore.kernel.org/r/20190922035906.10977-15-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After study, it was determined there was a double free of a CT iocb during
execution of lpfc_offline_prep and lpfc_offline. The prep routine issued
an abort for some CT iocbs, but the aborts did not complete fast enough for
a subsequent routine that waits for completion. Thus the driver proceeded
to lpfc_offline, which releases any pending iocbs. Unfortunately, the
completions for the aborts were then received which re-released the ct
iocbs.
Turns out the issue for why the aborts didn't complete fast enough was not
their time on the wire/in the adapter. It was the lpfc_work_done routine,
which requires the adapter state to be UP before it calls
lpfc_sli_handle_slow_ring_event() to process the completions. The issue is
the prep routine takes the link down as part of it's processing.
To fix, the following was performed:
- Prevent the offline routine from releasing iocbs that have had aborts
issued on them. Defer to the abort completions. Also means the driver
fully waits for the completions. Given this change, the recognition of
"driver-generated" status which then releases the iocb is no longer
valid. As such, the change made in the commit 296012285c is reverted.
As recognition of "driver-generated" status is no longer valid, this
patch reverts the changes made in
commit 296012285c ("scsi: lpfc: Fix leak of ELS completions on adapter reset")
- Modify lpfc_work_done to allow slow path completions so that the abort
completions aren't ignored.
- Updated the fdmi path to recognize a CT request that fails due to the
port being unusable. This stops FDMI retries. FDMI will be restarted on
next link up.
Link: https://lore.kernel.org/r/20190922035906.10977-14-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scenarios were seen where a host hung when the system booted or the host
was very slow in booting. The link would not come up and no luns were
visible to the host.
After investigation, this was found to be due to the introduction of a new
ACQE that adapter may generate to report a adapter hw warning. The ACQE was
delivered to the driver very early in adapter initialization, when the
driver did not expect command completion. As part of handling this
unexpected interrupt the an EQEs are consumed and discarded and the EQ
rearmed. The issue is the CQ that cause the EQE and thus the interrupt was
not processed and the CQ was left unarmed. Meaning it would no longer
generate a new interrupt condition. Subsequent mailbox commands used to
initialize the adapter use the same CQ, and as there was no completion
interrupt generated, the driver never saw the mailbox commands complete and
it would wait long command timeouts.
Fix by having the early flush routine also process the related CQ and rearm
the CQ.
Link: https://lore.kernel.org/r/20190922035906.10977-13-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged several scenarios where checking of null pointer values
wasn't consistent.
Fix the code to that be consistent on checking.
Link: https://lore.kernel.org/r/20190922035906.10977-12-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the port, running as a nvme target, receives an ABTS, it submits
commands to the adapter to Abort i/o outstanding in the adapter. The Abort
command formatting routine left a command field set to zero, which
instructs the adapter to generate an ABTS on the wire as part of cleaning
up the I/O. This is common operation for an initiator, but not for a
target.
Fix the driver to check whether an ABTS had been received for the I/O, and
if so, change the Abort command formatting so that the ABTS generation is
disabled (IA=1). No need to ABTS it when the other side already has.
Also refactored the code such that there is a single routine being used for
nvme or nvmet ABORT requests, and IA is an argument.
Link: https://lore.kernel.org/r/20190922035906.10977-11-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An issue was seen discovering all SCSI Luns when a target device undergoes
link bounce.
The driver currently does not qualify the FC4 support on the target.
Therefore it will send a SCSI PRLI and an NVMe PRLI. The expectation is
that the target will reject the PRLI if it is not supported. If a PRLI
times out, the driver will retry. The driver will not proceed with the
device until both SCSI and NVMe PRLIs are resolved. In the failure case,
the device is FCP only and does not respond to the NVMe PRLI, thus
initiating the wait/retry loop in the driver. During that time, a RSCN is
received (device bounced) causing the driver to issue a GID_FT. The GID_FT
response comes back before the PRLI mess is resolved and it prematurely
cancels the PRLI retry logic and leaves the device in a STE_PRLI_ISSUE
state. Discovery with the target never completes or resets.
Fix by resetting the node state back to STE_NPR_NODE when GID_FT completes,
thereby restarting the discovery process for the node.
Link: https://lore.kernel.org/r/20190922035906.10977-10-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Faults are seen with RIP of lpfc_scsi_cmd_iocb_cmpl(). The failure is when
lpfc_update_status is being called as part of the completion. After
debugging, it was seen the issue was the shost pointer that the driver
derived from the scsi cmd. The crash showed the cmd->device pointer being
bogus, which is likely as the scsi devices were offlined prior. The bogus
device pointer caused subsequent pointers derived from the location,
specifically the vport, to be bogus.
Fix by adjusting the calling sequence to pass in the vport rather than
having to derive it from the cmd structure.
Link: https://lore.kernel.org/r/20190922035906.10977-9-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When target-side fault injections are made, the driver isn't reconnecting
to the remote port. The driver is logging "2753" error messages which
state:
"PLOGI failure DID:1B2400 Status:x3/xf0240008"
The failures status is indicating a Illegal field error, which points to
the Temporary RPI field being used for the ELS. This error typically means
the driver used an RPI that was already registered (shouldn't be registered
if using it in this context).
Study has found that if the driver were in discovery attempts and
encountered an error, it wouldn't flag the temporary rpi in error. Yet the
rpi was released for reallocation in these error paths and another ELS
could allocate the rpi. In the failure situation a retry was done on an ELS
that had encountered an error, and as the rpi wasn't marked in error, the
ELS reused the rpi it originally allocated. But that rpi had been allocated
by a different ELS issued after the original error and before the retry
attempt. The different ELS had succeeded and the RPI was registered.
Fix by marking the rpi state for the node to be in error, aka as needing
reallocation, upon an error in the els processing. Error state marking is
always done prior to release back to the internal rpi free list, which the
driver wasn't doing in cases prior.
Also enhanced some of the logging to help in the next case of problem
troubleshooting.
Link: https://lore.kernel.org/r/20190922035906.10977-7-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior use-after-free mailbox fix solved it's problem by null'ing a ndlp
pointer. However, further testing has shown that this change causes a
later state change to occasionally be skipped, which results in a reference
count never being decremented thus the rpi is never released, which causes
a vport delete to never succeed.
Revise the fix in the prior patch to no longer null the ndlp. Instead the
RELEASE_RPI flag is set which will drive the release of the rpi.
Given the new code was added at a deep indentation level, refactor the code
block using a new routine that avoids the indentation issues.
Fixes: 9b16406864 ("scsi: lpfc: Fix use-after-free mailbox cmd completion")
Link: https://lore.kernel.org/r/20190922035906.10977-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The nvme-fc transport may call to abort an io on controller reset. If the
driver is out of resources to issue an abort command, it just gives up and
does nothing. The transport expects the lldd to always be able to terminate
an io it has issued. At that point, the controller hangs waiting for
aborted ios to be returned. Note: flaged by "6136" and "6176" error
messages.
Root issue was the adapter mis-allocated the number resources it allocated
for command entries for the adapter.
Convert the driver to allocate command resources based on the number of
xris supported by the FC port - 1 resource for the original command and 1
resource for the abort request.
Link: https://lore.kernel.org/r/20190922035906.10977-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Coverity flagged missing status check on register read that flags a
poisoned data return value.
Add checking of register read status.
Link: https://lore.kernel.org/r/20190922035906.10977-4-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of spin_lock_irq may re-enable interrupts prematurely.
Convert to spin_lock. Note: code is under the phba->hba_lock which has been
locked with irqsave.
Link: https://lore.kernel.org/r/20190922035906.10977-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After exchanging PLOGI on an SLI-3 adapter, the PRLI exchange failed. Link
trace showed the port was assigned a non-zero n_port_id, but didn't use the
address on the PRLI. The assigned address is set on the port by the
CONFIG_LINK mailbox command. The driver responded to the PRLI before the
mailbox command completed. Thus the PRLI response used the old n_port_id.
Defer the PRLI response until CONFIG_LINK completes.
Link: https://lore.kernel.org/r/20190922035906.10977-2-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=aAPP
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/post-2019-09-24' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"Some later additions that weren't quite done for the first pull
request, and also a few fixes that have arrived since.
This contains:
- Kill silly pktcdvd warning on attempting to register a non-scsi
passthrough device (me)
- Use symbolic constants for the block t10 protection types, and
switch to handling it in core rather than in the drivers (Max)
- libahci platform missing node put fix (Nishka)
- Small series of fixes for BFQ (Paolo)
- Fix possible nbd crash (Xiubo)"
* tag 'for-5.4/post-2019-09-24' of git://git.kernel.dk/linux-block:
block: drop device references in bsg_queue_rq()
block: t10-pi: fix -Wswitch warning
pktcdvd: remove warning on attempting to register non-passthrough dev
ata: libahci_platform: Add of_node_put() before loop exit
nbd: fix possible page fault for nbd disk
nbd: rename the runtime flags as NBD_RT_ prefixed
block, bfq: push up injection only after setting service time
block, bfq: increase update frequency of inject limit
block, bfq: reduce upper bound for inject limit to max_rq_in_driver+1
block, bfq: update inject limit only after injection occurred
block: centralize PI remapping logic to the block layer
block: use symbolic constants for t10_pi type
This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates.
The only core change this time around is the addition of request
batching for virtio. Since batching requires an additional flag to
use, it should be invisible to the rest of the drivers.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXYQE/yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXs9AP4usPY5
OpMlF6OiKFNeJrCdhCScVghf9uHbc7UA6cP+EgD/bCtRgcDe1ZjOTYWdeTwvwWqA
ltWYonnv6Lg3b1f9yqI=
=jRC/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
only core change this time around is the addition of request batching
for virtio. Since batching requires an additional flag to use, it
should be invisible to the rest of the drivers"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
scsi: hisi_sas: Fix the conflict between device gone and host reset
scsi: hisi_sas: Add BIST support for phy loopback
scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
scsi: hisi_sas: Remove some unused function arguments
scsi: hisi_sas: Remove redundant work declaration
scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
scsi: hisi_sas: Assign NCQ tag for all NCQ commands
scsi: hisi_sas: Update all the registers after suspend and resume
scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
scsi: virtio_scsi: unplug LUNs when events missed
scsi: scsi_dh_rdac: zero cdb in send_mode_select()
scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
...
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
Currently t10_pi_prepare/t10_pi_complete functions are called during the
NVMe and SCSi layers command preparetion/completion, but their actual
place should be the block layer since T10-PI is a general data integrity
feature that is used by block storage protocols. Introduce .prepare_fn
and .complete_fn callbacks within the integrity profile that each type
can implement according to its needs.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Fixed to not call queue integrity functions if BLK_DEV_INTEGRITY
isn't defined in the config.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
-----BEGIN PGP SIGNATURE-----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=Qt+h
-----END PGP SIGNATURE-----
Merge tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Two NVMe pull requests:
- ana log parse fix from Anton
- nvme quirks support for Apple devices from Ben
- fix missing bio completion tracing for multipath stack devices
from Hannes and Mikhail
- IP TOS settings for nvme rdma and tcp transports from Israel
- rq_dma_dir cleanups from Israel
- tracing for Get LBA Status command from Minwoo
- Some nvme-tcp cleanups from Minwoo, Potnuri and Myself
- Some consolidation between the fabrics transports for handling
the CAP register
- reset race with ns scanning fix for fabrics (move fabrics
commands to a dedicated request queue with a different lifetime
from the admin request queue)."
- controller reset and namespace scan races fixes
- nvme discovery log change uevent support
- naming improvements from Keith
- multiple discovery controllers reject fix from James
- some regular cleanups from various people
- Series fixing (and re-fixing) null_blk debug printing and nr_devices
checks (André)
- A few pull requests from Song, with fixes from Andy, Guoqing,
Guilherme, Neil, Nigel, and Yufen.
- REQ_OP_ZONE_RESET_ALL support (Chaitanya)
- Bio merge handling unification (Christoph)
- Pick default elevator correctly for devices with special needs
(Damien)
- Block stats fixes (Hou)
- Timeout and support devices nbd fixes (Mike)
- Series fixing races around elevator switching and device add/remove
(Ming)
- sed-opal cleanups (Revanth)
- Per device weight support for BFQ (Fam)
- Support for blk-iocost, a new model that can properly account cost of
IO workloads. (Tejun)
- blk-cgroup writeback fixes (Tejun)
- paride queue init fixes (zhengbin)
- blk_set_runtime_active() cleanup (Stanley)
- Block segment mapping optimizations (Bart)
- lightnvm fixes (Hans/Minwoo/YueHaibing)
- Various little fixes and cleanups
* tag 'for-5.4/block-2019-09-16' of git://git.kernel.dk/linux-block: (186 commits)
null_blk: format pr_* logs with pr_fmt
null_blk: match the type of parameter nr_devices
null_blk: do not fail the module load with zero devices
block: also check RQF_STATS in blk_mq_need_time_stamp()
block: make rq sector size accessible for block stats
bfq: Fix bfq linkage error
raid5: use bio_end_sector in r5_next_bio
raid5: remove STRIPE_OPS_REQ_PENDING
md: add feature flag MD_FEATURE_RAID0_LAYOUT
md/raid0: avoid RAID0 data corruption due to layout confusion.
raid5: don't set STRIPE_HANDLE to stripe which is in batch list
raid5: don't increment read_errors on EILSEQ return
nvmet: fix a wrong error status returned in error log page
nvme: send discovery log page change events to userspace
nvme: add uevent variables for controller devices
nvme: enable aen regardless of the presence of I/O queues
nvme-fabrics: allow discovery subsystems accept a kato
nvmet: Use PTR_ERR_OR_ZERO() in nvmet_init_discovery()
nvme: Remove redundant assignment of cq vector
nvme: Assign subsys instance from first ctrl
...
-----BEGIN PGP SIGNATURE-----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=L5e+
-----END PGP SIGNATURE-----
Merge tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
Currently blk_set_runtime_active() is checking if q->dev is null by
itself, thus remove the same checking in its user: scsi_dev_type_resume().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When device gone, it will check whether it is during reset, if not, it will
send internal task abort. Before internal task abort returned, reset
begins, and it will check whether SAS_PHY_UNUSED is set, if not, it will
call hisi_sas_init_device(), but at that time domain_device may already be
freed or part of it is freed, so it may referenece null pointer in
hisi_sas_init_device(). It may occur as follows:
thread0 thread1
hisi_sas_dev_gone()
check whether in RESET(no)
internal task abort
reset prep
soft_reset
... (part of reset_done)
internal task abort failed
release resource anyway
clear_itct
device->lldd_dev=NULL
hisi_sas_reset_init_all_device
check sas_dev->dev_type is SAS_PHY_UNUSED and
!device
set dev_type SAS_PHY_UNUSED
sas_free_device
hisi_sas_init_device
...
Semaphore hisi_hba.sema is used to sync the processes of device gone and
host reset.
To solve the issue, expand the scope that semaphore protects and let them
never occur together.
And also some places will check whether domain_device is NULL to judge
whether the device is gone. So when device gone, need to clear
sas_dev->sas_device.
Link: https://lore.kernel.org/r/1567774537-20003-14-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add BIST (built in self test) support for phy loopback.
Through the new debugfs interface, the user can configure loopback
mode/linkrate/phy id/code mode before enabling it. And also user can
enable/disable BIST function.
Link: https://lore.kernel.org/r/1567774537-20003-13-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We extract the code of memory allocate and construct an new function for
it. We think it's convenient for subsequent optimization.
Link: https://lore.kernel.org/r/1567774537-20003-12-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some function arguments are unused, so remove them.
Also move the timeout print in for wait_cmds_complete_timeout_vX_hw()
callsites into that same function.
Link: https://lore.kernel.org/r/1567774537-20003-11-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the NCQ tag is only assigned for FPDMA READ and FPDMA WRITE
commands, and for other NCQ commands (such as FPDMA SEND), their NCQ tags
are set in the delivery command to 0.
So for all the NCQ commands, we also need to assign normal NCQ tag for
them, so drop the command type check in hisi_sas_get_ncq_tag() [drop
hisi_sas_get_ncq_tag() altogether actually], and always use the ATA command
NCQ tag when appropriate.
Link: https://lore.kernel.org/r/1567774537-20003-8-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After suspend and resume, the HW registers will be set back to their
initial value. We use init_reg_v3_hw() to set some registers, but some
registers are set via firmware in ACPI "_RST" method, so add reset handler
before init_reg_v3_hw().
Link: https://lore.kernel.org/r/1567774537-20003-7-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When init device for SAS disks, it will send TMF IO to clear disks. At that
time TMF IO is broken by some operations such as injecting controller reset
from HW RAs event, the TMF IO will be timeout, and at last device will be
gone. Print is as followed:
hisi_sas_v3_hw 0000:74:02.0: dev[240:1] found
...
hisi_sas_v3_hw 0000:74:02.0: controller resetting...
hisi_sas_v3_hw 0000:74:02.0: phyup: phy7 link_rate=10(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy0 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy1 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy2 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy3 link_rate=9(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy6 link_rate=10(sata)
hisi_sas_v3_hw 0000:74:02.0: phyup: phy5 link_rate=11
hisi_sas_v3_hw 0000:74:02.0: phyup: phy4 link_rate=11
hisi_sas_v3_hw 0000:74:02.0: controller reset complete
hisi_sas_v3_hw 0000:74:02.0: abort tmf: TMF task timeout and not done
hisi_sas_v3_hw 0000:74:02.0: dev[240:1] is gone
sas: driver on host 0000:74:02.0 cannot handle device 5000c500a75a860d,
error:5
To improve the reliability, retry TMF IO max of 3 times for SAS disks which
is the same as softreset does.
Link: https://lore.kernel.org/r/1567774537-20003-6-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
