The STATUS_SCAN_HW is set before calling iwlagn_set_pan_params
(used as an input to calculate slot time allocation). The bit needs
to be cleared in case sending the command fails.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We know whether we received a frame in GF format
or not, add it to the radiotap information.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In channel switch, instead of relying on our internal
channel database, just use the mac80211 channel that
we filled with that information on startup.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of iterating our own channel list,
use the mac80211 channel list since that's
already processed per band and thus makes
for less code.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 will never set, switch to, or scan on an
invalid channel, so remove the code to validate
the channels against the driver channel list.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 guarantees that the channel pointer is
always valid, so we can use that instead of our
own channel list.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of functions were temporarily made non-static
for experimental work, make them static again now.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a remain on channel request from mac80211 is followed by
a request to tx a mgmt frame offchannel, it is possible that
the remain on channel expires before the device reported the
tx status for the frame. This causes a race condition in
mac80211.
To fix this, delay the ROC notification to mac80211 until the
device reported the Tx status for all frames in the aux queue.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that the BSS context is not active (for example
when the current mode is set to GO), or that the vif->type is
different than station. In such a case we cannot
call mac80211 to report the average rssi for the interface
(the function assumes that the vif is valid and that the type
is station).
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We separate reading of device's eeprom content from writing it back
to the device's sram.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a debugging log when using shadow
registers. Also fix a minor typo in this
connection.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly clean up indentation around parentheses
after if, function calls, etc. and also a few
unneeded line breaks and some other things.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is a library to be used by multiple
opmodes, so move it into the iwlwifi module.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the next step in splitting up the driver,
making the uCode API dependent pieces of it live
in separate modules. Right now there's only one
so it's not user-selectable, but we're actively
working on more.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is common, not uCode API specific, so move
it to the transport together with the command
header struct definition.
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is intended to be set whenever wakeup will be
needed upon suspend, not only when suspending, so
use the new callbacks to set it then.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is needed by other transports besides PCIe, thus
moving to a common location.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches suggested adding the __printf attribute
to the __iwl_dbg function to check arguments; add it
to all of the logging functions (err, warn, info, dbg
and crit.)
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We missed passing an argument to the
debug print. Fix it.
Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug prints were wrong and buggy. The HW pointer wasn't printed
correctly, it was mixed up with the pointer to the rxbuf.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This chip is used at least by the D-Link DWA-525 adapter.
Signed-off-by: Alex Villac<ED>s Lasso <a_villacis@palosanto.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This returns many of the values that formerly could
only be obtained from debugfs. This should be an
improvement when trying to access these counters
programatically. Currently this support is only
enabled when DEBUGFS is enabled because otherwise
these stats are not accumulated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we provide excess buffer size for 'simple_read_from_buffer'
for modal EEPROM dump. This results in trailing NULL bytes
at the end of EEPROM dump, fix this.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reported-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Holger Schurig <holgerschurig@gogglemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is potentially called with NULL pointers, for example, look at
brcmf_c_prec_enq(). Since it's a free() function, probably people
expect it to handle NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code causes a static checker warning because "pi" gets dereferenced
before it is checked. The dereference is inside the write_phy_reg()
function which is called from wlc_phy_write_txmacreg_nphy().
This code is only called from wlc_phy_init_nphy() and "pi" is a
valid pointer so we can remove the check for NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
D-Link DWA-123 rev A1
Signed-off-by: Albert Pool<albertpool@solcon.nl>
Cc: <stable@vger.kernel.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit c21eebb503
"wl12xx: add RX filters ACX commands" breaks the build
when CONFIG_PM isn't defined:
ERROR: "wl1271_rx_filter_get_fields_size"
[drivers/net/wireless/ti/wlcore/wlcore.ko] undefined!
ERROR: "wl1271_rx_filter_flatten_fields"
[drivers/net/wireless/ti/wlcore/wlcore.ko] undefined!
code in drivers/net/wireless/ti/wlcore/acx.c is using these
functions unconditionally while they are #ifdefed CONFIG_PM.
Fix it by ifdefing all relevant RX filters code with CONFIG_PM.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR933x, the internal regulator settings need to be applied before the
PLL init to avoid stability issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"> Can you provide more information about the issues with high power devices?
Tx being flakey and Rx not working at all."
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_setup_buffer() can fail if there is no ath_buf left, or if mapping DMA
failed. In this case it frees the skb passed to it.
If ath_tx_setup_buffer is called from ath_tx_form_aggr, the skb is still
linked into the tid buffer list and must be dequeued before being released.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been found that active Rx can interfere with stopping tx DMA, which
could result in at least parts of those "Failed to stop Tx DMA!" messages.
Stopping rx before tx should prevent that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware is more than 300KB big and you should not use kmalloc for
such big allocations. This allocation with kmalloc failed on my mips
based device (BCM47186).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver disables interrupt just after requesting it and enables it
later, after interface is up. However currently there is a time window
between request_irq() and disable_irq() where if interrupt arrives, the
driver oopses because it's not yet ready to process it. This can be
reproduced by inserting the module, associating and removing the module
multiple times.
Eliminate this race by setting IRQF_NOAUTOEN flag before request_irq().
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If drv->op_mode is NULL after trying to init the
opmode, we go to the wrong label. Fix this, and
clean up the code a bit.
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a station fails in
iwl_restore_stations, the driver treats it
like a successful station add and sends a
link quality command, when it it shouldn't.
This patch fixes one of the potential
sources for kernel warnings like this one:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-sta.c:905 iwl_send_lq_cmd+0x130/0x217 [iwlwifi]()
Hardware name: 3323A2G
Modules linked in: ...
Pid: 17359, comm: kworker/u:2 Tainted: G O 3.3.0-wl+ #1
Call Trace:
[<ffffffff81039620>] warn_slowpath_common+0x7e/0x96
[<ffffffff8103964d>] warn_slowpath_null+0x15/0x17
[<ffffffffa02a9f0b>] iwl_send_lq_cmd+0x130/0x217 [iwlwifi]
[<ffffffffa02aa1fb>] iwl_restore_stations+0x209/0x289 [iwlwifi]
[<ffffffffa02b07c2>] iwlagn_commit_rxon+0x602/0x7bd [iwlwifi]
[<ffffffffa02b111f>] iwlagn_bss_info_changed+0x247/0x31a [iwlwifi]
[<ffffffffa0861437>] ieee80211_bss_info_change_notify+0x1a5/0x1ba [mac80211]
[<ffffffffa088afad>] ieee80211_destroy_auth_data+0x4b/0x70 [mac80211]
[<ffffffffa088df26>] ieee80211_sta_work+0xb5/0x954 [mac80211]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode16 option is still very much work in
progress, so there's no need to ask any users
about it. Remove the option and code for now,
we'll put it back when it's actually working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shadow registers in the device are meant to
allow the driver to update certain device
registers without needing to wake up all
components of the device. However, using
this feature in the device causes
communication between the driver and the
device to become unreliable, resulting in
host command timeouts.
Disable this feature by default till a fix is
available for the bug.
Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic that allows to have a short TFD queue was completely wrong.
We do maintain 256 Transmit Frame Descriptors, but they point to
recycled buffers. We used to attach and de-attach different TFDs for
the same buffer and it worked since they pointed to the same buffer.
Also zero the number of BDs after unmapping a TFD. This seems not
necessary since we don't reclaim the same TFD twice, but I like
housekeeping.
This patch solves this warning:
[ 6427.079855] WARNING: at lib/dma-debug.c:866 check_unmap+0x727/0x7a0()
[ 6427.079859] Hardware name: Latitude E6410
[ 6427.079865] iwlwifi 0000:02:00.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x00000000296d393c] [size=8 bytes]
[ 6427.079870] Modules linked in: ...
[ 6427.079950] Pid: 6613, comm: ifconfig Tainted: G O 3.3.3 #5
[ 6427.079954] Call Trace:
[ 6427.079963] [<c10337a2>] warn_slowpath_common+0x72/0xa0
[ 6427.079982] [<c1033873>] warn_slowpath_fmt+0x33/0x40
[ 6427.079988] [<c12dcb77>] check_unmap+0x727/0x7a0
[ 6427.079995] [<c12dcdaa>] debug_dma_unmap_page+0x5a/0x80
[ 6427.080024] [<fe2312ac>] iwlagn_unmap_tfd+0x12c/0x180 [iwlwifi]
[ 6427.080048] [<fe231349>] iwlagn_txq_free_tfd+0x49/0xb0 [iwlwifi]
[ 6427.080071] [<fe228e37>] iwl_tx_queue_unmap+0x67/0x90 [iwlwifi]
[ 6427.080095] [<fe22d221>] iwl_trans_pcie_stop_device+0x341/0x7b0 [iwlwifi]
[ 6427.080113] [<fe204b0e>] iwl_down+0x17e/0x260 [iwlwifi]
[ 6427.080132] [<fe20efec>] iwlagn_mac_stop+0x6c/0xf0 [iwlwifi]
[ 6427.080168] [<fd8480ce>] ieee80211_stop_device+0x5e/0x190 [mac80211]
[ 6427.080198] [<fd833208>] ieee80211_do_stop+0x288/0x620 [mac80211]
[ 6427.080243] [<fd8335b7>] ieee80211_stop+0x17/0x20 [mac80211]
[ 6427.080250] [<c148dac1>] __dev_close_many+0x81/0xd0
[ 6427.080270] [<c148db3d>] __dev_close+0x2d/0x50
[ 6427.080276] [<c148d152>] __dev_change_flags+0x82/0x150
[ 6427.080282] [<c148e3e3>] dev_change_flags+0x23/0x60
[ 6427.080289] [<c14f6320>] devinet_ioctl+0x6a0/0x770
[ 6427.080296] [<c14f8705>] inet_ioctl+0x95/0xb0
[ 6427.080304] [<c147a0f0>] sock_ioctl+0x70/0x270
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <ordex@autistici.org>
Tested-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Cc: stable@vger.kernel.org #2.6.38+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as well.
We deleted a staging driver, which was nice, and finally dropped the
obsolete usbfs code, which will make Al happy to never have to touch
that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were due
to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
=4jM1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
