SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set master->max_speed_hz then spi core will handle checking transfer speed.
The behavior is different from current code when the speed_hz is greater than
the maximum transfer speed supported by the controller.
Unless there is other good reason, I think we had better make the behavior
consistent with what spi core does.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses struct octeon_spi_setup to store max_speed_hz, chip_select and
mode settings of current spi device.
We can always get the same settings in octeon_spi_do_transfer() by msg->spi.
So this patch removes struct octeon_spi_setup and octeon_spi_setup,
octeon_spi_cleanup functions.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The purpose of commit 1e8a52e18c
"spi: By default setup spi_masters with 1 chipselect and dynamics bus number"
is to avoid setting default value for bus_num and num_chipselect in spi master
drivers. So let's remove the duplicate code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_spi_register_master() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 543bb25 "spi: add ability to validate xfer->bits_per_word in SPI
core", the driver can set bits_per_word_mask for the master then the SPI core
will reject transfers that attempt to use an unsupported bits_per_word value.
So we can remove octeon_spi_validate_bpw() and let SPI core handle the checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both prepare_transfer_hardware and unprepare_transfer_hardware callbacks are
optional, so we don't need to implement an empty function for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass master to platform_set_drvdata() then we can remove my_master pointer.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the driver, link it into the kbuild system and provide device tree
binding documentation.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/4292/
Signed-off-by: John Crispin <blogic@openwrt.org>
