After the drm_bridge_connector_init() helper function has been added,
the ADV driver has been changed accordingly. However, the 'type'
field of the bridge structure was left unset, which makes the helper
function always return -EINVAL.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org> # tested on DragonBoard 410c
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200720124228.12552-1-laurentiu.palcu@oss.nxp.com
Lontium Lt9611 is a DSI to HDMI bridge which supports two DSI ports and
I2S port as an input and HDMI port as output
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # fix lt9611_bridge_mode_valid
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-4-vkoul@kernel.org
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
For hdmi-codec, we need to update struct hdmi_codec_ops,
and all its users in the same time.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87d055xxj2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
clang static analysis flags this error
sil-sii8620.c:184:2: warning: Undefined or garbage value
returned to caller [core.uninitialized.UndefReturn]
return ret;
^~~~~~~~~~
sii8620_readb calls sii8620_read_buf.
sii8620_read_buf can return without setting its output
pararmeter 'ret'.
So initialize ret.
Fixes: ce6e153f41 ("drm/bridge: add Silicon Image SiI8620 driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200712152453.27510-1-trix@redhat.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708121604.14292-1-grandmaster@al2klimov.de
It doesn't hurt to add the bridge in the global bridge list also for
platform specific dw-hdmi drivers which are based on the component
framework. This can be achieved by moving the drm_bridge_add() function
call from dw_hdmi_probe() to __dw_hdmi_probe(). A counterpart movement
for drm_bridge_remove() is also needed then. Moreover, since drm_bridge_add()
initializes &bridge->hpd_mutex, this may help those platform specific
dw-hdmi drivers(based on the component framework) avoid accessing the
uninitialized mutex in drm_bridge_hpd_notify() which is called in
dw_hdmi_irq(). Putting drm_bridge_add() in __dw_hdmi_probe() just before
it returns successfully should bring no logic change for platforms based
on the DRM bridge API, which is a good choice from safety point of view.
Also, __dw_hdmi_probe() is renamed to dw_hdmi_probe() since dw_hdmi_probe()
does nothing else but calling __dw_hdmi_probe(). Similar renaming applies
to the __dw_hdmi_remove()/dw_hdmi_remove() pair.
Fixes: ec971aaa67 ("drm: bridge: dw-hdmi: Make connector creation optional")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-2-git-send-email-victor.liu@nxp.com
It's unnecessary to cleanup the i2c adapter and the ddc pointer in
the bailout path of __dw_hdmi_probe(), since the adapter is not
added and the ddc pointer is not set.
Fixes: a23d6265f0 ("drm: bridge: dw-hdmi: Extract PHY interrupt setup to a function")
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Dariusz Marcinkiewicz <darekm@google.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: dri-devel@lists.freedesktop.org
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1594260156-8316-1-git-send-email-victor.liu@nxp.com
Some conflicts with ttm_bo->offset removal, but drm-misc-next needs updating to v5.8.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
ti-sn65dsi86 bridge is enumerated as a runtime device. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend will not be called
and it kept the bridge regulators and gpios ON which resulted
in platform not entering into XO shutdown.
Add changes to force suspend on the runtime device during pm sleep.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609120455.20458-1-harigovi@codeaurora.org
dw-mipi-dsi does not use any definition from drm_probe_helper.
Coverity output:
Event unnecessary_header:
Including .../include/drm/drm_probe_helper.h does not provide any
needed symbols.
Reviewed-by: Yannick Fertre <yannick.fertre@st.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Angelo Ribeiro <angelo.ribeiro@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/171ff1fb3918664a570dc8f2f34b446612505f76.1585832665.git.angelo.ribeiro@synopsys.com
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
Implement the drm_bridge_funcs .detect() and .get_edid() operations, and
call drm_bridge_hpd_notify() notify to report HPD. This provides the
necessary API to support disabling connector creation, do so by
accepting DRM_BRIDGE_ATTACH_NO_CONNECTOR in dw_hdmi_bridge_attach().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-23-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_connector explicitly to the internal functions that require it.
The functions that still access the connector from the dw_hdmi structure
are dw_hdmi_connector_create() and __dw_hdmi_probe(). The former access
is expected, as that's where the internal connector is created. The
latter will be addressed separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-22-laurent.pinchart+renesas@ideasonboard.com
Store the connector that the bridge is currently wired to in the dw_hdmi
structure. This is currently identical to the connector field, but will
differ once the driver supports disabling connector creation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-21-laurent.pinchart+renesas@ideasonboard.com
To prepare for making connector creation optional in the driver, pass
the drm_display_info explicitly to dw_hdmi_support_scdc(). The pointer
is passed to the callers where required, particularly to the
dw_hdmi_phy_ops .init() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-19-laurent.pinchart+renesas@ideasonboard.com
Several internal functions take a drm_display_mode argument to configure
the HDMI encoder or the HDMI PHY. They must not modify the mode, make
the pointer const to enforce that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-18-laurent.pinchart+renesas@ideasonboard.com
Replace the drm_connector pointer passed to the .mode_valid() function
with a const drm_display_info pointer, as that's all the function should
need. Use the display info passed to the bridge .mode_valid() operation
instead of retrieving it from the connector, to prepare for make
connector creation optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-16-laurent.pinchart+renesas@ideasonboard.com
The .configure_phy() operation takes a dw_hdmi_plat_data pointer as a
context argument. This differs from .mode_valid() that takes a custom
private context pointer, causing possible confusion. Make the
dw_hdmi_plat_data operations more consistent by passing the private
context pointer to .configure_phy() as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-13-laurent.pinchart+renesas@ideasonboard.com
Platform glue drivers for dw_hdmi may need to access device-specific
data from their .mode_valid() implementation. They currently have no
clean way to do so, and one driver hacks around it by accessing the
dev_private data of the drm_device retrieved from the connector.
Add a priv_data void pointer to the dw_hdmi_plat_data structure, and
pass it to the .mode_valid() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-12-laurent.pinchart+renesas@ideasonboard.com
When validating a mode, bridges may need to do so in the context of a
display, as specified by drm_display_info. An example is the meson
dw-hdmi bridge that needs to consider the YUV 4:2:0 output format to
perform clock calculations.
Bridges that need the display info currently retrieve it from the
drm_connector created by the bridge. This gets in the way of moving
connector creation out of bridge drivers. To make this possible, pass
the drm_display_info to drm_bridge_funcs .mode_valid().
Changes to the bridge drivers have been performed with the following
coccinelle semantic patch and have been compile-tested.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.mode_valid = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
identifier mode;
@@
enum drm_mode_status fn(
struct drm_bridge *bridge,
+ const struct drm_display_info *info,
const struct drm_display_mode *mode
)
{
...
}
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org> # for the nwl-dsi part:
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-11-laurent.pinchart+renesas@ideasonboard.com
Instead of poking into the DT node of the next bridge for its DDC bus
and implementing the .get_modes() and .detect() connector operations
manually, retrieve the next bridge in the chain and delegate these
operations to it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-7-laurent.pinchart+renesas@ideasonboard.com
The drm_bridge_get_edid() function is documented to return an error
pointer on error. The underlying .get_edid() operation, however, returns
NULL on error, and so do the drm_get_edid() and drm_do_get_edid()
functions upon which .get_edid() is usually implemented. Make
drm_bridge_get_edid() return NULL on error to be consistent.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-6-laurent.pinchart+renesas@ideasonboard.com
Now that the driver supports all the connector-related bridge
operations, make the connector creation optional. This enables usage of
the adv7511 with the DRM bridge connector helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-5-laurent.pinchart+renesas@ideasonboard.com
Implement the bridge connector-related .get_edid(), .detect() and
.hpd_notify() operations, and report the related bridge capabilities.
Output status detection is implemented using the same backend as for the
DRM connector, but requires making mode retrieval at detection time
optional as no pointer to the connector is available to the bridge
.detect() operation. The reason for the need to retrieve modes at
detection time is unclear to me, and this may benefit from further
refactoring of hot plug handling code.
Hot plug detection is notified through the bridge HPD notification
framework when the bridge is used without creating a connector, and
falls back to the existing implementation otherwise. CEC handling of
disconnection is handled in the new .hpd_notify() operation in the new
code path.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526011505.31884-4-laurent.pinchart+renesas@ideasonboard.com
The tfp410 has a data de-skew feature that allows the user to compensate
the skew between IDCK and the pixel data and control signals.
In the driver, the setup and hold times are calculated from the de-skew
value. This retrieves the deskew value from the DT using the proper
datatype and range check as described by the binding (u32 from 0 to 7).
This fix results from a change in the ti,tfp410 DT binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617094633.19663-4-ricardo.canuelo@collabora.com
The ti_sn_bridge_gpio_set() got the return value of
regmap_update_bits() but didn't check it. The function can't return
an error value, but we should at least print a warning if it didn't
work.
This fixes a compiler warning about setting "ret" but not using it.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.4.Ia4376fd88cdc6e8f8b43c65548458305f82f1d61@changeid
When building we were getting an error:
warning: cannot understand function prototype:
'const unsigned int ti_sn_bridge_dp_rate_lut[] = '
Arrays aren't supposed to be marked with "/**" kerneldoc comments. Fix.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.2.If3807e4ebf7f0440f64c3069edcfac9a70171940@changeid
The kernel test robot noted that if "OF" is defined (which is needed
to select DRM_TI_SN65DSI86 at all) but not OF_GPIO that we'd get
compile failures because some of the members that we access in "struct
gpio_chip" are only defined "#if defined(CONFIG_OF_GPIO)".
All the GPIO bits in the driver are all nicely separated out. We'll
guard them with the same "#if defined" that the header has and add a
little stub function if OF_GPIO is not defined.
Fixes: 27ed2b3f22 ("drm/bridge: ti-sn65dsi86: Export bridge GPIOs to Linux")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612123003.v2.1.Ibe95d8f3daef01e5c57d4c8c398f04d6a839492c@changeid
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
-----BEGIN PGP SIGNATURE-----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=vMHE
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
The ti-sn65dsi86 MIPI DSI to eDP bridge chip supports arbitrary
remapping of eDP lanes and also polarity inversion. Both of these
features have been described in the device tree bindings for the
device since the beginning but were never implemented in the driver.
Implement both of them.
Part of this change also allows you to (via the same device tree
bindings) specify to use fewer than the max number of DP lanes that
the panel reports. This could be useful if your display supports more
lanes but only a few are hooked up on your board.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200518114656.REPOST.v2.1.Ibc8eeddcee94984a608d6900b46f9ffde4045da4@changeid
If the rate in our table is _equal_ to the rate we want then it's OK
to pick it. It doesn't need to be greater than the one we want.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504213225.1.I21646c7c37ff63f52ae6cdccc9bc829fbc3d9424@changeid
The AUX channel transfer error bits in the status register are latched
and need to be cleared. Clear them before doing our transfer so we
don't see old bits and get confused.
Without this patch having a single failure would mean that all future
transfers would look like they failed.
Fixes: b814ec6d45 ("drm/bridge: ti-sn65dsi86: Implement AUX channel")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200508163314.1.Idfa69d5d3fc9623083c0ff78572fea87dccb199c@changeid
The ti-sn65dsi86 MIPI DSI to eDP bridge chip has 4 pins on it that can
be used as GPIOs in a system. Each pin can be configured as input,
output, or a special function for the bridge chip. These are:
- GPIO1: SUSPEND Input
- GPIO2: DSIA VSYNC
- GPIO3: DSIA HSYNC or VSYNC
- GPIO4: PWM
Let's expose these pins as GPIOs. A few notes:
- Access to ti-sn65dsi86 is via i2c so we set "can_sleep".
- These pins can't be configured for IRQ.
- There are no programmable pulls or other fancy features.
- Keeping the bridge chip powered might be expensive. The driver is
setup such that if all used GPIOs are only inputs we'll power the
bridge chip on just long enough to read the GPIO and then power it
off again. Setting a GPIO as output will keep the bridge powered.
- If someone releases a GPIO we'll implicitly switch it to an input so
we no longer need to keep the bridge powered for it.
Because of all of the above limitations we just need to implement a
bare-bones GPIO driver. The device tree bindings already account for
this device being a GPIO controller so we only need the driver changes
for it.
NOTE: Despite the fact that these pins are nominally muxable I don't
believe it makes sense to expose them through the pinctrl interface as
well as the GPIO interface. The special functions are things that the
bridge chip driver itself would care about and it can just configure
the pins as needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[added pdata->gchip.base = -1;]
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.1.Ia50267a5549392af8b37e67092ca653a59c95886@changeid
This is a driver for video encoder with VGA and DVI/HDMI outputs.
There is no documentation for the chip -- the operation was guessed from
what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names
come from the ch7035 driver in Mediatek's GPL code dump.
Only bare minimum is implemented -- no fancy stuff, such as scaling. That
would only worsen our misery. We don't load the firmware and we don't need
to even bother enabling the MCU. There are probably no distributable
firmware images anyway.
Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60,
with VGA as well as DVI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424213539.93157-4-lkundrak@v3.sk
Some older versions of gcc badly optimize code that passes
an inline function argument into another function by reference,
causing huge stack usage:
drivers/gpu/drm/bridge/tc358768.c: In function 'tc358768_bridge_pre_enable':
drivers/gpu/drm/bridge/tc358768.c:840:1: error: the frame size of 2256 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Use a temporary variable as a workaround and add a comment pointing
to the gcc bug.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428215408.4111675-1-arnd@arndb.de
Since commit 89958b7cd9 ("drm/bridge: panel: Infer connector type from
panel by default"), drm_panel_bridge_add() and their variants can return
NULL and an error pointer. This is fine but none of the actual users of
the API are checking for the NULL value. Instead of change all the
users, seems reasonable to return an error pointer instead. So change
the returned value for those functions when the connector type is unknown.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416210654.2468805-1-enric.balletbo@collabora.com
The panel connector type should be set by the panel not the bridge, so
remove the connector_type assignment.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416164404.2418426-2-enric.balletbo@collabora.com
Globally update my email address in six files scattered through the
tree.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Some drivers (e.g. sun4i-drm) need this info to decide whether they
need to enable dithering. Currently driver reports what panel supports
and if panel supports 8 we don't get dithering enabled.
Hardcode BPC to 6 for now since that's the only BPC
that driver supports.
Fixes: 6aa1926980 ("drm/bridge: Add Analogix anx6345 support")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200329222253.2941405-1-anarsoul@gmail.com
ADV7511 support sample rates up to 192kHz. CTS and N parameters should
be computed accordingly so this commit extend the list up to maximum
supported sample rate.
Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200413113513.86091-2-bogdan.togorean@analog.com
This adds initial support for the NWL MIPI DSI Host controller found on
i.MX8 SoCs.
It adds support for the i.MX8MQ but the same IP can be found on
e.g. the i.MX8QXP.
It has been tested on the Librem 5 devkit using mxsfb.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1cf5750f734e33d005564cd89c576eaf3c1c192b.1586427783.git.agx@sigxcpu.org
Analogix_dp driver acquires all its resources in the ->bind() callback,
what is a bit against the component driver based approach, where the
driver initialization is split into a probe(), where all resources are
gathered, and a bind(), where all objects are created and a compound
driver is initialized.
Extract all the resource related operations to analogix_dp_probe() and
analogix_dp_remove(), then call them before/after registration of the
device components from the main Exynos DP and Rockchip DP drivers. Also
move the plat_data initialization to the probe() to make it available for
the analogix_dp_probe() function.
This fixes the multiple calls to the bind() of the DRM compound driver
when the DP PHY driver is not yet loaded/probed:
[drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops [exynosdrm])
exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm])
exynos-dp 145b0000.dp-controller: no DP phy configured
exynos-drm exynos-drm: failed to bind 145b0000.dp-controller (ops exynos_dp_ops [exynosdrm]): -517
exynos-drm exynos-drm: master bind failed: -517
...
[drm] Exynos DRM: using 14400000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 14400000.fimd (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 14450000.mixer (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 145b0000.dp-controller (ops hdmi_enable [exynosdrm])
exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_enable [exynosdrm])
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
Console: switching to colour frame buffer device 170x48
exynos-drm exynos-drm: fb0: exynosdrmfb frame buffer device
[drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1
...
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310103427.26048-1-m.szyprowski@samsung.com
(cherry picked from commit 83a196773b)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Add missing documentation to fix following warning:
panel.c:303: warning: Function parameter or member 'bridge' not described in 'drm_panel_bridge_connector'
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Mihail Atanassov <Mihail.Atanassov@arm.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328132025.19910-7-sam@ravnborg.org
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6BIG4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGlHUH/RCFve2sfHRPjRW+
xR5SaLVAw6XKvtKBq7yvKmHEwqNJnL79IHyqqtSrtfFr2FfaH/KvYiCbbAezvSrM
np0udGu7STKGd21CWuyEZJudyhXkOwMRNiFiCXWp7rs35oh8T0TpJxMzo2Nc1nLk
JFQPqAP6OSvq4IkWEywKQI+Au3Z1IBf83xVjZ1s+MKPQHYD49x2hc4cQntL5/cnm
a3DoR2iBkYiGZCZ9dDqAqJTnMQIiCbACdZXgGjNRUpdyA/dtAjsMl11NPYHm8TA2
3AHBupAK50WBZGad6xv2qKQyScsmoJG2mv92QjlOFz0Tpiu6rLnDlLYREDVB6YH6
qbLDsc8=
=XEIU
-----END PGP SIGNATURE-----
Merge v5.6 into drm-next
msm needed rc6, so I just went and merged release
(msm has been in drm-next outside of this tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Don't confuse user with meaningless warning about failure in getting
regulators in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226101307.16708-1-m.szyprowski@samsung.com
is_color_space_conversion() is a misnomer. It checks not only if color
space conversion is needed, but also if format conversion is needed.
This is actually desired behaviour because result of this function
determines if CSC block should be enabled or not (CSC block can also do
format conversion).
In order to clear misunderstandings, let's rework
is_color_space_conversion() to do exactly what is supposed to do and add
another function which will determine if CSC block must be enabled or
not.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-5-jernej.skrabec@siol.net
CEA 861 standard requestis that RGB quantization range is "limited" for
CEA modes. Support that by adding CSC matrix which downscales values.
This allows proper color reproduction on TV and PC monitor at the same
time. In future, override property can be added, like "Broadcast RGB"
in i915 driver.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-4-jernej.skrabec@siol.net
Setting scan mode to "none" confuses some TVs like LG B8, which randomly
change overscan percentage over time. Digital outputs like HDMI and DVI,
handled by this controller, don't really need overscan, so we can always
set scan mode to underscan. Actually, this is exactly what
drm_hdmi_avi_infoframe_from_display_mode() already does, so we can just
remove offending line.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
[updated commit message]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304232512.51616-3-jernej.skrabec@siol.net
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5lkYceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGpHQH/RJrzcaZHo4lw88m
Jf7vBZ9DYUlRgqE0pxTHWmodNObKRqpwOUGflUcWbb/7GD2LQUfeqhSECVQyTID9
N9y7FcPvx321Qhc3EkZ24DBYk0+DQ0K2FVUrSa/PxO0n7czxxXWaLRDmlSULEd3R
D4pVs3zEWOBXJHUAvUQ5R+lKfkeWKNeeepeh+rezuhpdWFBRNz4Jjr5QUJ8od5xI
sIwobYmESJqTRVBHqW8g2T2/yIsFJ78GCXs8DZLe1wxh40UbxdYDTA0NDDTHKzK6
lxzBgcmKzuge+1OVmzxLouNWMnPcjFlVgXWVerpSy3/SIFFkzzUWeMbqm6hKuhOn
wAlcIgI=
=VQUc
-----END PGP SIGNATURE-----
Merge v5.6-rc5 into drm-next
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now the DW-HDMI Controller supports the HDMI2.0 modes, enable support
for these modes in the connector if the platform supports them.
We limit these modes to DW-HDMI IP version >= 0x200a which
are designed to support HDMI2.0 display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-6-narmstrong@baylibre.com
Add the atomic_get_output_bus_fmts, atomic_get_input_bus_fmts to negociate
the possible output and input formats for the current mode and monitor,
and use the negotiated formats in a basic atomic_check callback.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-5-narmstrong@baylibre.com
Add the max_bpc property to the dw-hdmi connector to prepare support
for 10, 12 & 16bit output support.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304104052.17196-3-narmstrong@baylibre.com
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
Current code tries to store the link rate (in bps, which is a big
number) in a u8, which surely overflow. Then it's converted back to
bandwidth code (which is thus 0) and written to the chip.
The code sometimes works because the chip will automatically fallback to
the lowest possible DP link rate (1.62Gbps) when get the invalid value.
However, on the eDP panel of Olimex TERES-I, which wants 2.7Gbps link,
it failed.
As we had already read the link bandwidth as bandwidth code in earlier
code (to check whether it is supported), use it when setting bandwidth,
instead of converting it to link rate and then converting back.
Fixes: e1cff82c10 ("drm/bridge: fix anx6345 compilation for v5.5")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Torsten Duwe <duwe@lst.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221165127.813325-1-icenowy@aosc.io
The tfp410 driver can operate as part of a pipeline where the
drm_connector is created by the display controller. Enable this mode of
operation by skipping creation of a drm_connector internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-20-laurent.pinchart@ideasonboard.com
Now that a driver is available for display connectors, replace the
manual connector handling code with usage of the DRM bridge API. The
tfp410 driver doesn't deal with the display connector directly anymore,
but still delegates drm_connector operations to the next bridge. This
brings us one step closer to having the tfp410 driver handling the
TFP410 only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-19-laurent.pinchart@ideasonboard.com
Implement the newly added bridge connector operations, allowing the
usage of drm_bridge_panel with drm_bridge_connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-18-laurent.pinchart@ideasonboard.com
The TI TPD12S015 is an HDMI level shifter and ESD protector controlled
through GPIOs. Add a DRM bridge driver for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-17-laurent.pinchart@ideasonboard.com
Display connectors are modelled in DT as a device node, but have so far
been handled manually in several bridge drivers. This resulted in
duplicate code in several bridge drivers, with slightly different (and
thus confusing) logics.
In order to fix this, implement a bridge driver for display connectors.
The driver centralises logic for the DVI, HDMI, VGAn composite and
S-video connectors and exposes corresponding bridge operations.
This driver in itself doesn't solve the issue completely, changes in
bridge and display controller drivers are needed to make use of the new
connector driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-16-laurent.pinchart@ideasonboard.com
The TI OPA362 is an analog video amplifier controlled through a GPIO. Add
support for it to the simple-bridge driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-15-laurent.pinchart@ideasonboard.com
If an enable GPIO is declared in the firmware, assert it when enabling
the bridge and deassert it when disabling it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-14-laurent.pinchart@ideasonboard.com
Create a new simple_bridge_info structure that stores information about
the bridge model, and store the bridge timings in there, along with the
connector type. Use that new structure for of_device_id data. This
enables support for non-VGA bridges.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-13-laurent.pinchart@ideasonboard.com
The dumb-vga-dac driver can support simple DRM bridges without being
limited to VGA DACs. Rename it to simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-12-laurent.pinchart@ideasonboard.com
The dumb-vga-dac driver is a simple DRM bridge driver for simple VGA
DACs that don't require configuration. Other non-VGA bridges fall in a
similar category, and would benefit from a common driver. Prepare for
this by renaming the internal symbols from dumb-vga-dac to
simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-11-laurent.pinchart@ideasonboard.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
Propagate bus format/flags so that the previous bridge element in the
chain knows which input format the panel bridge expects.
v11:
* Fix a typo in the subject
* Update the commit message so it's readable by itself
v10:
* Add changelog to the commit message
v8 -> v9:
* No changes
v7:
* Set atomic state hooks explicitly
v4 -> v6:
* Not part of the series
v3:
* Adjust things to match the new bus-format negotiation approach
* Use drm_atomic_helper_bridge_propagate_bus_fmt
* Don't implement ->atomic_check() (the core now takes care of bus
flags propagation)
v2:
* Adjust things to match the new bus-format negotiation approach
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128135514.108171-11-boris.brezillon@collabora.com
The drm_bridge_funcs structure is never modified, make it const. Making
it read-only can improve security as the structure contains function
pointers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224230056.2157-1-laurent.pinchart+renesas@ideasonboard.com
Factor out the manual container_of() uses to a common to_lvds_codec()
macro to shorten lines (and provide better type safety, although that
won't matter much in this case).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224225645.28060-1-laurent.pinchart+renesas@ideasonboard.com
of_get_regulator() will unconditionally add "-supply" to form the
property name. This is documented in commit 69511a452e ("map consumer
regulator based on device tree"). Remove the suffix from the requests.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200218155440.BEFB968C65@verein.lst.de
Based on work by Bjorn Andersson <bjorn.andersson@linaro.org>,
Jeffrey Hugo <jeffrey.l.hugo@gmail.com>, and
Rob Clark <robdclark@chromium.org>.
Let's read the SUPPORTED_LINK_RATES and/or MAX_LINK_RATE (depending on
the eDP version of the sink) to figure out what eDP rates are
supported and pick the ideal one.
NOTE: I have only personally tested this code on eDP panels that are
1.3 or older. Code reading SUPPORTED_LINK_RATES for DP 1.4+ was
tested by hacking the code to pretend that a table was there.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.9.Ib59207b66db377380d13748752d6fce5596462c5@changeid
If we fail training at a lower DP link rate let's now keep trying
until we run out of rates to try. Basically the algorithm here is to
start at the link rate that is the theoretical minimum and then slowly
bump up until we run out of rates or hit the max rate of the sink. We
query the sink using a DPCD read.
This is, in fact, important in practice. Specifically at least one
panel hooked up to the bridge (AUO B116XAK01) had a theoretical min
rate more than 1.62 GHz (if run at 24 bpp) and fails to train at the
next rate (2.16 GHz). It would train at 2.7 GHz, though.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.8.I251add713bc5c97225200894ab110ea9183434fd@changeid
We'll re-organize the ti_sn_bridge_enable() function a bit to group
together all the parts relating to link training and split them into a
sub-function. This is not intended to have any functional change and
is in preparation for trying link training several times at different
rates. One small side effect here is that if link training fails
we'll now leave the DP PLL disabled, but that seems like a sane thing
to do.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.7.I1fc75ad11db9048ef08cfe1ab7322753d9a219c7@changeid
The current bridge driver always forced us to use 24 bits per pixel
over the DP link. This is a waste if you are hooked up to a panel
that only supports 6 bits per color or fewer, since in that case you
can run at 18 bits per pixel and thus end up at a lower DP clock rate.
Let's support this.
While at it, let's clean up the math in the function to avoid rounding
errors (and round in the correct direction when we have to round).
Numbers are sufficiently small (because mode->clock is in kHz) that we
don't need to worry about integer overflow.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[narmstrong: s/ran/can/]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.6.Iaf8d698f4e5253d658ae283d2fd07268076a7c27@changeid
At least one panel hooked up to the bridge (AUO B116XAK01) only
supports 1 lane of DP. Let's read this information and stop
hardcoding 4 DP lanes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.5.Idbd0051d0de53f7e9d18a291ea33011c0854fcc6@changeid
The driver used to say that the value to program into bridge register
0x93 was dp_lanes - 1. Looking at the datasheet for the bridge, this
is wrong. The data sheet says:
* 1 = 1 lane
* 2 = 2 lanes
* 3 = 4 lanes
A more proper way to express this encoding is min(dp_lanes, 3).
At the moment this change has zero effect because we've hardcoded the
number of DP lanes to 4. ...and (4 - 1) == min(4, 3). How fortunate!
...but soon we'll stop hardcoding the number of lanes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.4.If3e2d0493e7b6e8b510ea90d8724ff760379b3ba@changeid
The ti-sn65dsi86 is a bridge from MIPI to DP and thus has two links:
the MIPI link and the DP link. The two links do not need to have the
same format or number of lanes. Stop using MIPI variables when
talking about the DP link.
This has zero functional change because:
* currently we are hardcoding the MIPI link as unpacked RGB888 which
requires 24 bits and currently we are not changing the DP link rate
from the bridge's default of 8 bits per pixel.
* currently we are hardcoding both the MIPI and DP as being 4 lanes.
This is all in prep for fixing some of the above.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218143416.v3.3.Ia6e05f4961adb0d4a0d32ba769dd7781ee8db431@changeid
