Newfile: arch/sh/include/cpu-sh2a/cpu/addrspace.h
This file seems had be removed to use fallback (cpu-common/cpu/addrspace.h),
but, I'd like to add sh2a specific file here, because
1. the values defined there are not suitable for sh2a.
2. I don't think there is "common" definition for these values.
Values are chosen by consideration of followings...
P1 is 0. perhaps no question.
P2 is from hardware manual, which says no-cache area starts at 20000000.
It means that P? space size=20000000.
P3 is P2+size since asm/ptrace.h uses P3 as a end of P2.
P4 is P3+size since asm/fixup.h uses P4 as a end of P3.
Signed-off-by: Takashi YOSHII <yoshii.takashi@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH never really supported a.out, so this was all just copied over blindly
from x86 way back when. As we don't reference linux/a.out.h anywhere in
the tree, these can now safely be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the changes in commits:
7d6d637dac4f72c4279e
on powerpc. Adding in TIF_NOTIFY_RESUME, and cleaning up the syscall
tracing to be more generic. This is an incremental step to turning
on tracehook, as well as unifying more of the ptrace and signal code
across the 32/64 split.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the single stepping done by sh/sh64 ptrace implementations
to use the generic user_enable/disable_single_step(), and subsequently
rips out a lot of ptrace request cases that are now handled generically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
Presently this is protected by a CONFIG_VSYSCALL ifdef so we don't
inadvertently trigger the creation of the gate VMA on CPUs where we don't
enable the vDSO, which is obviously not visible to userspace. Fix this up
by adding in an ifndef __KERNEL__ check at the same time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the workaround in 2b4b2bb421
and cleans up __put_user_asm() to get the sizing right from the onset.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
