Fix copy/paste fail in kerneldocs for intel_audio_codec_disable().
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114191127.16188-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
encoder->type isn't genreally safe around DDI ports, so let's
replace some uses in the audio code with the crtc state's
output_types instead.
Actually in these cases encoder->type would work since the DP
SST case is only relevant for VLV/CHV and encoder->type==DP
is a thing on those platforms. The DP MST cases would work
as well since MST encoder->type==DP_MST always. But I think
it's best to try and minimize the encoder->type use in general
to avoid showing a bad example to people.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171030184654.17429-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Explicitly pass the crtc and connector states into the audio
code enable/disable hooks, and plumb them all the way down.
This gets rid of almost all crtc->config and encoder->crtc
uses. The one place where we still use them is
i915_audio_component_sync_audio_rate() since that gets called from
the audio driver and we don't have explicit states around then.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171030184654.17429-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Let's remove the dependency on I915_MAX_PIPES. Instead, get the number
of pipes from platform information.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507630626-23806-2-git-send-email-mika.kahola@intel.com
drm_edid_to_eld() initializes the connector ELD to zero, overwriting the
ELD connector type initialized in intel_audio_codec_enable(). If
userspace does getconnector and thus get_modes after modeset, a
subsequent audio component i915_audio_component_get_eld() call will
receive an ELD without the connector type properly set. It's fine for
HDMI, but screws up audio for DP.
Always set the ELD connector type at intel_connector_update_modes()
based on the connector type. We can drop the connector type update from
intel_audio_codec_enable().
Credits to Joseph Nuzman <jnuzman@gmail.com> for figuring this out.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joseph Nuzman <jnuzman@gmail.com>
Reported-by: Joseph Nuzman <jnuzman@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101583
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Joseph Nuzman <jnuzman@gmail.com>
Cc: stable@vger.kernel.org # v4.10+, maybe earlier
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919153813.29808-1-jani.nikula@intel.com
Shuffle the arguments to intel_lpe_audio_notify() around a bit. Pipe
and port being the most important things, so let's put the first, and
thre rest can come in as is. Also constify the eld argument.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-8-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
There's no need to distinguish between the DP link rate and HDMI TMDS
clock for the purposes of the LPE audio. Both are actually the same
thing more or less, which is the link symbol clock. So let's just
call the thing ls_clock and simplify the code.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-6-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
4 weeks worth of stuff since I was traveling&lazy:
- lspcon improvements (Imre)
- proper atomic state for cdclk handling (Ville)
- gpu reset improvements (Chris)
- lots and lots of polish around fences, requests, waiting and
everything related all over (both gem and modeset code), from Chris
- atomic by default on gen5+ minus byt/bsw (Maarten did the patch to
flip the default, really this is a massive joint team effort)
- moar power domains, now 64bit (Ander)
- big pile of in-kernel unit tests for various gem subsystems (Chris),
including simple mock objects for i915 device and and the ggtt
manager.
- i915_gpu_info in debugfs, for taking a snapshot of the current gpu
state. Same thing as i915_error_state, but useful if the kernel didn't
notice something is stick. From Chris.
- bxt dsi fixes (Umar Shankar)
- bxt w/a updates (Jani)
- no more struct_mutex for gem object unreference (Chris)
- some execlist refactoring (Tvrtko)
- color manager support for glk (Ander)
- improve the power-well sync code to better take over from the
firmware (Imre)
- gem tracepoint polish (Tvrtko)
- lots of glk fixes all around (Ander)
- ctx switch improvements (Chris)
- glk dsi support&fixes (Deepak M)
- dsi fixes for vlv and clanups, lots of them (Hans de Goede)
- switch to i915.ko types in lots of our internal modeset code (Ander)
- byt/bsw atomic wm update code, yay (Ville)
* tag 'drm-intel-next-2017-03-06' of git://anongit.freedesktop.org/git/drm-intel: (432 commits)
drm/i915: Update DRIVER_DATE to 20170306
drm/i915: Don't use enums for hardware engine id
drm/i915: Split breadcrumbs spinlock into two
drm/i915: Refactor wakeup of the next breadcrumb waiter
drm/i915: Take reference for signaling the request from hardirq
drm/i915: Add FIFO underrun tracepoints
drm/i915: Add cxsr toggle tracepoint
drm/i915: Add VLV/CHV watermark/FIFO programming tracepoints
drm/i915: Add plane update/disable tracepoints
drm/i915: Kill level 0 wm hack for VLV/CHV
drm/i915: Workaround VLV/CHV sprite1->sprite0 enable underrun
drm/i915: Sanitize VLV/CHV watermarks properly
drm/i915: Only use update_wm_{pre,post} for pre-ilk platforms
drm/i915: Nuke crtc->wm.cxsr_allowed
drm/i915: Compute proper intermediate wms for vlv/cvh
drm/i915: Skip useless watermark/FIFO related work on VLV/CHV when not needed
drm/i915: Compute vlv/chv wms the atomic way
drm/i915: Compute VLV/CHV FIFO sizes based on the PM2 watermarks
drm/i915: Plop vlv/chv fifo sizes into crtc state
drm/i915: Plop vlv wm state into crtc_state
...
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Introduce intel_cdclk state which for now will track the cdclk
frequency, the vco frequency and the reference frequency (not sure we
want the last one, but I put it there anyway). We'll also make the
.get_cdclk() function fill out this state structure rather than
just returning the current cdclk frequency.
One immediate benefit is that calling .get_cdclk() will no longer
clobber state stored under dev_priv unless ex[plicitly told to do
so. Previously it clobbered the vco and reference clocks stored
there on some platforms.
We'll expand the use of this structure to actually precomputing the
state and whatnot later.
v2: Constify intel_cdclk_state_compare()
v3: Document intel_cdclk_state_compare()
v4: Deal with i945gm_get_cdclk()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207183345.19763-1-ville.syrjala@linux.intel.com
The LPE audio configuration depends on the pipe, thus we need to pass
the currently used pipe. It's now embedded in struct
intel_hdmi_lpe_audio_eld as well as port id.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pipe gets cleared to -1 for non-MST before the ELD audio
notification due to the MST audio support. This makes sense for
HD-audio that received the MST handling, but it's useless for LPE
audio. Handle the MST pipe hack conditionally only for HD-audio.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If DisplayPort is detected, pass flag and link rate to audio driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Notifiations like mode change, hot plug and edid to
the audio driver are added. This is inturn used by the
audio driver for its functionality.
A new interface file capturing the notifications needed by the
audio driver is added
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable support for HDMI LPE audio mode on Baytrail and
Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load:
1. Create a platform device to share MMIO/IRQ resources
2. Make the platform device child of i915 device for runtime PM.
3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the
LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jerome Anand <jerome.anand@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.
So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).
The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.
v2: fix conflict with IS_LP and 3 new cases for this
big core bucket:
- intel_ddi.c: intel_ddi_get_link_dpll
- intel_fbc.c: find_compression_threshold
- i915_gem_gtt.c: gtt_write_workarounds
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com
when num_pipes is zero, it indicates there is no display and HDMI
audio doesn't exist.
v2: Move the check from caller to callee for consistency.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Elaine Wang <elaine.wang@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482142746-21663-1-git-send-email-elaine.wang@intel.com
Some monitors will have noise or even no sound after
applying the patch 6014ac12.
In patch 6014ac12, it will reset the cts value to 0 for HDMI.
However, we need to disable Enable CTS or M Prog bit. This is
the initial setting after HW reset.
Fixes: 6014ac122e ("drm/i915/audio: set proper N/M in modeset")
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478853988-139842-1-git-send-email-libin.yang@intel.com
(cherry picked from commit 60abfbb86a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In initialization, audio driver will call functions get_eld() and etc.
But at that time, audio driver may not know whether it is DP MST or not.
In the original function get_saved_enc(), if it is DP MST, it requires to
set the pipe to the correct value, otherwise, pipe to be -1.
Although audio driver can get the knowledge whether it is in DP MST mode
or not by reading the codec register. It will drop performance each time
before it calls the get_eld and other similar functions. As gfx driver can
easily know whether it is in DP MST mode or not. Let's extend the
get_saved_enc() function to handle the situation that audio driver
still sends the device id info even it is in DP SST mode and return
the correct intel_encoder instead of panic.
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480569439-54252-1-git-send-email-libin.yang@intel.com
Some monitors will have noise or even no sound after
applying the patch 6014ac12.
In patch 6014ac12, it will reset the cts value to 0 for HDMI.
However, we need to disable Enable CTS or M Prog bit. This is
the initial setting after HW reset.
Fixes: 6014ac122e ("drm/i915/audio: set proper N/M in modeset")
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478853988-139842-1-git-send-email-libin.yang@intel.com
drm_select_eld requires mode_config.mutex and connection_mutex
because it looks at the connector list and at the legacy encoders.
This is not required, because when we call audio_codec_enable we know
which connector it was called for, so pass the state.
This also removes having to look at crtc->config.
Changes since v1:
- Use intel_crtc->pipe instead of drm_crtc_index. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478609742-13603-8-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
When modeset occurs and the LS_CLK is set to some special values in DP
mode, the N/M need to be set manually if audio is playing. Otherwise the
first several seconds may be silent in audio playback.
The relationship of Maud and Naud is expressed in the following
equation:
Maud/Naud = 512 * fs / f_LS_Clk
Please refer VESA DisplayPort Standard spec for details.
v2 by Jani:
- organize Maud/Naud table according to DP 1.4 spec
- add 64k and 128k audio rates
- update HSW_AUD_M_CTS_ENABLE register when Maud not found
- remove extra checks for port clock
- simplify Maud/Naud lookup
- reset patch author back to Libin
Cc: "Zhang, Keqiao" <keqiao.zhang@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Lin, Mengdong" <mengdong.lin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477407258-30599-3-git-send-email-jani.nikula@intel.com
The array contains the crtc clock, rely on that. While at it, debug log
the HDMI N value or automatic mode.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Lin, Mengdong" <mengdong.lin@intel.com>
Cc: Libin Yang <libin.yang@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477407258-30599-2-git-send-email-jani.nikula@intel.com
Saves 864 bytes of .rodata strings and ~100 of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
It's been over two months, git definitely lost it's marbles. Conflicts
resolved by picking our version, plus manually checking the diff with
the parent in drm-intel-next-queued to make sure git didn't do
anything stupid. It did, so I removed 2 occasions where it
double-inserted a bit of code. The diff is now just
- kernel-doc changes
- drm format/name changes
- display-info changes
so looks all reasonable.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
DP MST provides the capability to send multiple video and audio streams
through a single port. This requires the API's between i915 and audio
drivers to distinguish between multiple audio capable displays that can be
connected to a port. Currently only the port identity is shared in the
APIs. This patch adds support for MST with an additional parameter
'int pipe'. The existing parameter 'port' does not change it's meaning.
pipe =
MST : display pipe that the stream originates from
Non-MST : -1
Affected APIs:
struct i915_audio_component_ops
- int (*sync_audio_rate)(struct device *, int port, int rate);
+ int (*sync_audio_rate)(struct device *, int port, int pipe,
+ int rate);
- int (*get_eld)(struct device *, int port, bool *enabled,
- unsigned char *buf, int max_bytes);
+ int (*get_eld)(struct device *, int port, int pipe,
+ bool *enabled, unsigned char *buf, int max_bytes);
struct i915_audio_component_audio_ops
- void (*pin_eld_notify)(void *audio_ptr, int port);
+ void (*pin_eld_notify)(void *audio_ptr, int port, int pipe);
This patch makes dummy changes in the audio drivers (thanks Libin) for
build to succeed. The audio side drivers will send the right 'pipe' values
for MST in patches that will follow.
v2:
Renamed the new API parameter from 'dev_id' to 'pipe'. (Jim, Ville)
Included Asoc driver API compatibility changes from Jeeja.
Added WARN_ON() for invalid pipe in get_saved_encoder(). (Takashi)
Added comment for av_enc_map[] definition. (Takashi)
v3:
Fixed logic error introduced while renaming 'dev_id' as 'pipe' (Ville)
Renamed get_saved_encoder() to get_saved_enc() to reduce line length
v4:
Rebased.
Parameter check for pipe < -1 values in get_saved_enc() (Ville)
Switched to for_each_pipe() in get_saved_enc() (Ville)
Renamed 'pipe' to 'dev_id' in audio side code (Takashi)
v5:
Included a comment for the dev_id arg. (Libin)
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474488168-2343-1-git-send-email-dhinakaran.pandiyan@intel.com
With DP MST, a digital_port can carry more than one audio stream. Hence,
more than one audio_connector needs to be attached to intel_digital_port in
such cases. However, each stream is associated with an unique encoder. So,
instead of creating an array of audio_connectors per port, move
audio_connector from struct intel_digital_port to struct intel_encoder.
This also simplifies access to the right audio_connector from codec
functions in intel_audio.c that receive intel_encoder.
v2: Removed locals that are not needed anymore.
v3: No code change except for minor change in context.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474334681-22690-5-git-send-email-dhinakaran.pandiyan@intel.com
Now that we have the port enum stored in intel_encoder, use that instead of
dereferencing intel_dig_port. Saves us a few locals.
struct intel_encoder variables have been renamed to be consistent and
convey type information.
v2:
Fix incorrect 'enum port' member names - s/attached_port/port
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474334681-22690-4-git-send-email-dhinakaran.pandiyan@intel.com
- refactor the sseu code (Imre)
- refine guc dmesg output (Dave Gordon)
- more vgpu work
- more skl wm fixes (Lyude)
- refactor dpll code in prep for upfront link training (Jim Bride et al)
- consolidate all platform feature checks into intel_device_info (Carlos Santa)
- refactor elsp/execlist submission as prep for re-submission after hang
recovery and eventually scheduling (Chris Wilson)
- allow synchronous gpu reset handling, to remove tricky/impossible/fragile
error recovery code (Chris Wilson)
- prep work for nonblocking (execlist) submission, using fences to track
depencies and drive elsp submission (Chris Wilson)
- partial error recover/resubmission of non-guilty batches after hangs (Chris Wilson)
- full dma-buf implicit fencing support (Chris Wilson)
- dp link training fixes (Jim, Dhinkaran, Navare, ...)
- obey dp branch device pixel rate/bpc/clock limits (Mika Kahola), needed for
many vga dongles
- bunch of small cleanups and polish all over, as usual
[airlied: printing macros collided]
* tag 'drm-intel-next-2016-09-19' of git://anongit.freedesktop.org/drm-intel: (163 commits)
drm/i915: Update DRIVER_DATE to 20160919
drm: Fix DisplayPort branch device ID kernel-doc
drm/i915: use NULL for NULL pointers
drm/i915: do not use 'false' as a NULL pointer
drm/i915: make intel_dp_compute_bpp static
drm: Add DP branch device info on debugfs
drm/i915: Update bits per component for display info
drm/i915: Check pixel rate for DP to VGA dongle
drm/i915: Read DP branch device SW revision
drm/i915: Read DP branch device HW revision
drm/i915: Cleanup DisplayPort AUX channel initialization
drm: Read DP branch device id
drm: Helper to read max bits per component
drm: Helper to read max clock rate
drm: Drop VGA from bpc definitions
drm: Add missing DP downstream port types
drm/i915: Add ddb size field to device info structure
drm/i915/guc: general tidying up (submission)
drm/i915/guc: general tidying up (loader)
drm/i915: clarify PMINTRMSK/pm_intr_keep usage
...
We currently have a mix of struct device *device, struct device *kdev,
and struct device *dev (the latter forcing us to refer to
struct drm_device as something else than the normal dev).
To simplify things, always use kdev when referring to struct device.
v2: Replace the dev_to_drm_minor() macro with the inline function
kdev_to_drm_minor().
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160822103245.24069-3-david.weinehall@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These are the leftovers I could only track down using keep_warnings =
True. For some of them we might want to update our style guide on how
to reference structures and constants, not sure ...
Cc: Markus Heiser <markus.heiser@darmarit.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471034937-651-1-git-send-email-daniel.vetter@ffwll.ch
On Haswell/Broadwell, the HD-Audio block is inside the HDMI/display
power well and so the sna-hda audio codec acquires the display power
well while it is operational. However, Skylake separates the powerwells
again, but yet we still need the audio powerwell to setup the registers.
(But then the hardware uses those registers even while powered off???)
Acquiring the powerwell around setting the chicken bits when setting up
the audio channel does at least silence the WARNs from touching our
registers whilst unpowered. We silence our own test cases, but maybe
there is a latent bug in using the audio channel?
v2: Grab both rpm wakelock and audio wakelock
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96214
Fixes: 03b135cebc "ALSA: hda - remove dependency on i915 power well for SKL")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Libin Yang <libin.yang@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Marius Vlad <marius.c.vlad@intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1470240540-29004-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bunch of places still look for DP encoders manually. Just call
intel_crtc_has_dp_encoder(). Note that many of these places don't
look for EDP or DP_MST, but it's still fine to replace them because
* for audio we don't enable audio on eDP anyway
* the code that lack DP MST check is only for plaforms that
don't support MST anyway
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-8-git-send-email-ville.syrjala@linux.intel.com
With the introduction of the output_types mask, intel_pipe_has_type()
and intel_pipe_will_have_type() are basically the same thing. Replace
them with a new intel_crtc_has_type() (identical to
intel_pipe_will_have_type() actually).
v2: Rebase
v3: Make intel_crtc_has_type() static inline (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-5-git-send-email-ville.syrjala@linux.intel.com
Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.
text data bss dec hex filename
1068757 4565 416 1073738 10624a drivers/gpu/drm/i915/i915.ko
1066949 4565 416 1071930 105b3a drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)
and for good measure the dev_priv->dev backpointer was removed entirely.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467711623-2905-4-git-send-email-chris@chris-wilson.co.uk
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
Right now MST audio is causing too many kernel panics to really keep
around in the kernel. On top of that, even after fixing said panics it's
still basically non-functional (at least on all the setups I've tested
it on). Revert until we have a proper solution for this.
This reverts commit 3d52ccf52f.
Signed-off-by: Lyude <cpaul@redhat.com>
Fixes: 3d52ccf52f ("drm/i915: start adding dp mst audio")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462287692-28570-1-git-send-email-cpaul@redhat.com
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
