Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.
When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.
This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34786005ec ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e8270 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFPs can report two different power values, the transmit power and the
receive power. Add labels to make it clear which is which. Also add
labels to the other sensors, VCC power supply, bias and module
temperature.
sensors(1) now shows:
sff2-isa-0000
Adapter: ISA adapter
VCC: +3.23 V
temperature: +33.4 C
TX_power: 276.00 uW
RX_power: 20.00 uW
bias: +0.01 A
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emulate the 802.3bz MMD EEE registers for 2.5Gbps EEE on RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users have been removed we can remove genphy_config_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.
v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change implements retrieving all the error counters from the PHY.
The counters require that the RxErrCnt register (0x0014) be read first,
after which copies of the counters are latched into the registers. This
ensures that all registers read after RxErrCnt are synchronized at the
moment that they are read.
The counter values need to be accumulated by the driver, as each time that
RxErrCnt is read, the values that are latched are the ones that have
incremented from the last read.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.
This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet
The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).
The change has been adapted from the Aquantia PHY driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs supports 4 types of reset:
1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg
2. Reset via GPIO
3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs
4. Reset via reg GeSftRst (0xff0c) & request new pin configs
Resets 2, 3 & 4 are almost identical, with the exception that the crystal
oscillator is available during reset for 2.
This change implements subsystem software reset via the GeSftRst and
reloading the previous pin configuration (so reset number 3).
This will also reset the PHY core regs (similar to reset 1).
Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that
can be done, is to write to that register, wait a specific amount of time
(10 milliseconds should be enough) and try to read back and check if there
are no errors on read. A busy-wait-read won't work well, and may sometimes
work or not work.
In case phylib is configured to also do a reset via GPIO, the ADIN PHY may
be reset twice when the PHY device registers, but that isn't a problem,
since it's being done on boot (or PHY device register).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access
to access MMD registers for EEE.
The EEE register addresses (when using Clause 22) are available at
different addresses (than Clause 45), and since accessing these regs (via
Clause 22) needs a special mechanism, a translation table is required to
convert these addresses.
For Clause 45, this is not needed since the driver will likely never use
this access mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change hooks link-status-change interrupts to phylib.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports standard suspend/resume via BMCR reg.
Hook these functions into the `adin` driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdfhttps://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We will need the functionality of __set_linkmode_max_speed also for
linkmode bitmaps other than phydev->supported. Therefore split it.
v2:
- remove unused parameter from __set_linkmode_max_speed
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This driver does a funny dance disabling and re-enabling
RX and/or TX delays. In any of the RGMII-ID modes, it first
disables the delays, just to re-enable them again right
away. This looks like a needless exercise.
Just enable the respective delays when in any of the
relevant 'id' modes, and disable them otherwise.
Also, remove comments which don't add anything that can't be
seen by looking at the code.
Signed-off-by: André Draszik <git@andred.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the integrated 2.5Gbps PHY in Realtek RTL8125.
Advertisement of 2.5Gbps mode is done via a vendor-specific register.
Same applies to reading NBase-T link partner advertisement.
Unfortunately this 2.5Gbps PHY shares the PHY ID with the integrated
1Gbps PHY's in other Realtek network chips and so far no method is
known to differentiate them. As a workaround use a dedicated fake PHY ID
that is set by the network driver by intercepting the MDIO PHY ID read.
v2:
- Create dedicated PHY driver and use a fake PHY ID that is injected by
the network driver. Suggested by Andrew Lunn.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using linkmode_adv_to_mii_adv_t and linkmode_adv_to_mii_ctrl1000_t
allows to simplify the code. In addition avoiding the conversion to
the legacy u32 advertisement format allows to remove the warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 171a9bae68 ("staging/octeon: Allow test build on
!MIPS"), the following combination of configs cause a few Kconfig
warnings and build errors (distilled from arm allyesconfig and Randy's
randconfig builds):
CONFIG_NETDEVICES=y
CONFIG_STAGING=y
CONFIG_COMPILE_TEST=y
and CONFIG_OCTEON_ETHERNET as either a module or built-in.
WARNING: unmet direct dependencies detected for MDIO_OCTEON
Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y]
&& 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n]
Selected by [y]:
- OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC ||
COMPILE_TEST [=y]) && NETDEVICES [=y]
In file included from ../drivers/net/phy/mdio-octeon.c:14:
../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of
function ‘writeq’; did you mean ‘writel’?
[-Werror=implicit-function-declaration]
111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr)
| ^~~~~~
CONFIG_64BIT is not strictly necessary if the proper readq/writeq
definitions are included from io-64-nonatomic-lo-hi.h.
CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because
of commit f9dc9ac516 ("of/mdio: Add dummy functions in of_mdio.h.").
Fixes: 171a9bae68 ("staging/octeon: Allow test build on !MIPS")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.
The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_led_trigger_change_speed(), there is an if statement on line 48
to check whether phy->last_triggered is NULL:
if (!phy->last_triggered)
When phy->last_triggered is NULL, it is used on line 52:
led_trigger_event(&phy->last_triggered->trigger, LED_OFF);
Thus, a possible null-pointer dereference may occur.
To fix this bug, led_trigger_event(&phy->last_triggered->trigger,
LED_OFF) is called when phy->last_triggered is not NULL.
This bug is found by a static analysis tool STCheck written by
the OSLAB group in Tsinghua University.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f70 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocated for the stats array may contain arbitrary data.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e0e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc52 ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.
Since commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:
% ip link set up dev eth0
------------[ cut here ]------------
called from state UP
WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
Modules linked in:
CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
NIP: c0227bf0 LR: c0227bf0 CTR: c004d224
REGS: df547720 TRAP: 0700 Not tainted (5.2.0+)
MSR: 00029000 <CE,EE,ME> CR: 24002822 XER: 00000000
GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
NIP [c0227bf0] phy_start+0x74/0xc0
LR [c0227bf0] phy_start+0x74/0xc0
Call Trace:
[df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
[df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
[df547828] [c023cf08] gfar_enet_open+0x364/0x374
[df547898] [c029d870] __dev_open+0xe4/0x140
[df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
[df5478f8] [c029dc28] dev_change_flags+0x20/0x54
[df547918] [c02ae304] do_setlink+0x310/0x818
[df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df547c28] [c02b222c] rtnl_newlink+0x48/0x68
[df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
--- interrupt: c01 at 0xfd4e030
LR = 0xfd4e010
Instruction dump:
813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
---[ end trace d4c095aeaf6ea998 ]---
and
% ip link set down dev eth0
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88
<...>
Call Trace:
[df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
[df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
[df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
[df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
[df581858] [c0225608] phylink_stop+0x7c/0xe4
[df581868] [c023c57c] stop_gfar+0x7c/0x94
[df581888] [c023c5b8] gfar_close+0x24/0x94
[df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
[df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
[df5818f8] [c029dc28] dev_change_flags+0x20/0x54
[df581918] [c02ae304] do_setlink+0x310/0x818
[df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df581c28] [c02b222c] rtnl_newlink+0x48/0x68
[df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df581f38] [c000d1d8] ret_from_syscall+0x0/0x38
<...>
---[ end trace d4c095aeaf6ea999 ]---
SFP modules with the 1000Base-X interface are not affected.
Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.
Fixes: 2179626156 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
