While we support using both tx slots for sideband transmissions, it
appears that DisplayPort devices in the field didn't end up doing a very
good job of supporting it. From section 5.2.1 of the DP 2.0
specification:
There are MST Sink/Branch devices in the field that do not handle
interleaved message transactions.
To facilitate message transaction handling by downstream devices, an
MST Source device shall generate message transactions in an atomic
manner (i.e., the MST Source device shall not concurrently interleave
multiple message transactions). Therefore, an MST Source device shall
clear the Message_Sequence_No value in the Sideband_MSG_Header to 0.
This might come as a bit of a surprise since the vast majority of hubs
will support using both tx slots even if they don't support interleaved
message transactions, and we've also been using both tx slots since MST
was introduced into the kernel.
However, there is one device we've had trouble getting working
consistently with MST for so long that we actually assumed it was just
broken: the infamous Dell P2415Qb. Previously this monitor would appear
to work sometimes, but in most situations would end up timing out
LINK_ADDRESS messages almost at random until you power cycled the whole
display. After reading section 5.2.1 in the DP 2.0 spec, some closer
investigation into this infamous display revealed it was only ever
timing out on sideband messages in the second TX slot.
Sure enough, avoiding the second TX slot has suddenly made this monitor
function perfectly for the first time in five years. And since they
explicitly mention this in the specification, I doubt this is the only
monitor out there with this issue. This might even explain explain the
seemingly harmless garbage sideband responses we would occasionally see
with MST hubs!
So - rewrite our sideband TX handlers to only support one TX slot. In
order to simplify our sideband handling now that we don't support
transmitting to multiple MSTBs at once, we also move all state tracking
for down replies from mstbs to the topology manager.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Cc: Sean Paul <sean@poorly.run>
Cc: "Lin, Wayne" <Wayne.Lin@amd.com>
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424181308.770749-1-lyude@redhat.com
This reverts commit 6bb0942e8f.
Unfortunately it would appear that the rumors we've heard of sideband
message interleaving not being very well supported are true. On the
Lenovo ThinkPad Thunderbolt 3 dock that I have, interleaved messages
appear to just get dropped:
[drm:drm_dp_mst_wait_tx_reply [drm_kms_helper]] timedout msg send
00000000571ddfd0 2 1
[dp_mst] txmsg cur_offset=2 cur_len=2 seqno=1 state=SENT path_msg=1 dst=00
[dp_mst] type=ENUM_PATH_RESOURCES contents:
[dp_mst] port=2
DP descriptor for this hub:
OUI 90-cc-24 dev-ID SYNA3 HW-rev 1.0 SW-rev 3.12 quirks 0x0008
It would seem like as well that this is a somewhat well known issue in
the field. From section 5.4.2 of the DisplayPort 2.0 specification:
There are MST Sink/Branch devices in the field that do not handle
interleaved message transactions.
To facilitate message transaction handling by downstream devices, an
MST Source device shall generate message transactions in an atomic
manner (i.e., the MST Source device shall not concurrently interleave
multiple message transactions). Therefore, an MST Source device shall
clear the Message_Sequence_No value in the Sideband_MSG_Header to 0.
MST Source devices that support field policy updates by way of
software should update the policy to forego the generation of
interleaved message transactions.
This is a bit disappointing, as features like HDCP require that we send
a sideband request every ~2 seconds for each active stream. However,
there isn't really anything in the specification that allows us to
accurately probe for interleaved messages.
If it ends up being that we -really- need this in the future, we might
be able to whitelist hubs where interleaving is known to work-or maybe
try some sort of heuristics. But for now, let's just play it safe and
not use it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 6bb0942e8f ("drm/dp_mst: Remove single tx msg restriction.")
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200423164225.680178-1-lyude@redhat.com
Reviewed-by: Sean Paul <sean@poorly.run>
Although it's not unexpected for drm_dp_check_act_status() to fail due
to DPCD read failures (as the hub may have just been unplugged
suddenly), timeouts are a bit more worrying as they either mean we need
a longer timeout value, or we aren't setting up payload allocations
properly. So, let's start printing errors on timeouts.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406221253.1307209-5-lyude@redhat.com
Currently we only poll for an ACT up to 30 times, with a busy-wait delay
of 100µs between each attempt - giving us a timeout of 2900µs. While
this might seem sensible, it would appear that in certain scenarios it
can take dramatically longer then that for us to receive an ACT. On one
of the EVGA MST hubs that I have available, I observed said hub
sometimes taking longer then a second before signalling the ACT. These
delays mostly seem to occur when previous sideband messages we've sent
are NAKd by the hub, however it wouldn't be particularly surprising if
it's possible to reproduce times like this simply by introducing branch
devices with large LCTs since payload allocations have to take effect on
every downstream device up to the payload's target.
So, instead of just retrying 30 times we poll for the ACT for up to 3ms,
and additionally use usleep_range() to avoid a very long and rude
busy-wait. Note that the previous retry count of 30 appears to have been
arbitrarily chosen, as I can't find any mention of a recommended timeout
or retry count for ACTs in the DisplayPort 2.0 specification. This also
goes for the range we were previously using for udelay(), although I
suspect that was just copied from the recommended delay for link
training on SST devices.
Changes since v1:
* Use readx_poll_timeout() instead of open-coding timeout loop - Sean
Paul
Changes since v2:
* Increase poll interval to 200us - Sean Paul
* Print status in hex when we timeout waiting for ACT - Sean Paul
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Cc: Sean Paul <sean@poorly.run>
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406221253.1307209-4-lyude@redhat.com
Just add a bit more line wrapping, get rid of some extraneous
whitespace, remove an unneeded goto label, and move around some variable
declarations. No functional changes here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
[this isn't a fix, but it's needed for the fix that comes after this]
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Cc: Sean Paul <sean@poorly.run>
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406221253.1307209-3-lyude@redhat.com
Drive-by fix I noticed the other day - drm_dp_mst_has_audio() only ever
made sense back when we still had to validate ports before accessing
them in order to (attempt to) avoid NULL dereferences. Since we have
proper reference counting that guarantees we always can safely access
the MST port, there's no use in keeping this function around as all it
does is validate the port pointer before checking the audio status.
Note - drm_dp_mst_port->has_audio is technically protected by
drm_device->mode_config.connection_mutex, since it's only ever updated
from drm_dp_mst_get_edid(). Additionally, we change the declaration for
port in struct intel_connector to be properly typed, so we can directly
access it.
Changes since v1:
* Change type of intel_connector->port in a separate patch - Sean Paul
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406200646.1263435-2-lyude@redhat.com
It looks like that when we introduced the ability to handle multiple
down requests at once, we accidentally started dropping NAK replies -
causing sideband messages which got NAK'd to seemingly timeout and cause
all sorts of weirdness.
So, fix this by making sure we don't return from
drm_dp_mst_handle_down_rep() early, but instead treat NAKs like any
other message.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: fbc821c4a5 ("drm/mst: Support simultaneous down replies")
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Wayne Lin <waynelin@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200403200325.885628-1-lyude@redhat.com
Reviewed-by: Sean Paul <sean@poorly.run>
While we don't need this function to store an mstb anywhere for UP
requests since we process them asynchronously, we do need to make sure
that we don't try to write to **mstb for UP requests otherwise we'll
cause a NULL pointer deref:
RIP: 0010:drm_dp_get_one_sb_msg+0x4b/0x460 [drm_kms_helper]
Call Trace:
? vprintk_emit+0x16a/0x230
? drm_dp_mst_hpd_irq+0x133/0x1010 [drm_kms_helper]
drm_dp_mst_hpd_irq+0x133/0x1010 [drm_kms_helper]
? __drm_dbg+0x87/0x90 [drm]
? intel_dp_hpd_pulse+0x24b/0x400 [i915]
intel_dp_hpd_pulse+0x24b/0x400 [i915]
i915_digport_work_func+0xd6/0x160 [i915]
process_one_work+0x1a9/0x370
worker_thread+0x4d/0x3a0
kthread+0xf9/0x130
? process_one_work+0x370/0x370
? kthread_park+0x90/0x90
ret_from_fork+0x35/0x40
So, fix this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: fbc821c4a5 ("drm/mst: Support simultaneous down replies")
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <waynelin@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406193352.1245985-1-lyude@redhat.com
Reviewed-by: Sean Paul <sean@poorly.run>
Now that we've removed the last user of this callback, get rid of it and
drm_dp_destroy_connector().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200331205740.135525-5-lyude@redhat.com
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6BIG4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGlHUH/RCFve2sfHRPjRW+
xR5SaLVAw6XKvtKBq7yvKmHEwqNJnL79IHyqqtSrtfFr2FfaH/KvYiCbbAezvSrM
np0udGu7STKGd21CWuyEZJudyhXkOwMRNiFiCXWp7rs35oh8T0TpJxMzo2Nc1nLk
JFQPqAP6OSvq4IkWEywKQI+Au3Z1IBf83xVjZ1s+MKPQHYD49x2hc4cQntL5/cnm
a3DoR2iBkYiGZCZ9dDqAqJTnMQIiCbACdZXgGjNRUpdyA/dtAjsMl11NPYHm8TA2
3AHBupAK50WBZGad6xv2qKQyScsmoJG2mv92QjlOFz0Tpiu6rLnDlLYREDVB6YH6
qbLDsc8=
=XEIU
-----END PGP SIGNATURE-----
Merge v5.6 into drm-next
msm needed rc6, so I just went and merged release
(msm has been in drm-next outside of this tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we can support multiple simultaneous replies, remove the
restrictions placed on sending new tx msgs.
This patch essentially just reverts commit
5a64967a2f ("drm/dp_mst: Have DP_Tx send one msg at a time")
now that the problem is solved in a different way.
Cc: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <waynelin@amd.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213211523.156998-4-sean@poorly.run
Currently we have one down reply message servicing the mst manager, so
we need to serialize all tx msgs to ensure we only have one message in
flight at a time. For obvious reasons this is suboptimal (but less
suboptimal than the free-for-all we had before serialization).
This patch removes the single down_rep_recv message from manager and
adds 2 replies in the branch structure. The 2 replies mirrors the tx_slots
which we use to rate-limit outgoing messages and correspond to seqno in
the packet headers.
Cc: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <waynelin@amd.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213211523.156998-3-sean@poorly.run
In preparation of per-branch device down message handling, separate
header parsing from message building. This will allow us to peek at
figure out which branch device the message is from before starting to
parse the message contents.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <waynelin@amd.com>
[seanpaul s/drm_dp_sideband_msg_build/drm_dp_sideband_msg_set_header/]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200213211523.156998-2-sean@poorly.run
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAl5sIZ0ACgkQ+mJfZA7r
E8o1LQf+L/Vpm46QQGEyzHINf/gTQvFvumuNAX352vEHaKUgLtTuI7xfpd0c83G1
5VI+L0Q/ARvakkgfZuHYInlxc9azkcPF1wXb3bLqkoiJ15ydwx5GWjVpZ8uFT+fG
xzaHBqhqUcvw/kXI1Cy5kIDAlFO9rKLsoLS2qQF9BsYHyxa52ok9/hW+lM7C+vfR
aYvEr7aAK0o06mqgwc3DHXGuzaS1S9kxtvj9ZkHNsD9iwD4rrEIvW3BPuDqEVkGq
TkKfThhzJp2FDjXkgCQbLm2BQmxBS0aihwNsQ/lDUUAxcFiuRYwMSoT63vPD1OYI
lgG0BuJkwK7csJIMrnOs/ZAMeKyTQA==
=vrB8
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2020-03-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200314001535.GA2969344@intel.com
Sigh, this is mostly my fault for not giving commit cd82d82cbc
("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
enough scrutiny during review. The way we're checking bandwidth
limitations here is mostly wrong:
For starters, drm_dp_mst_atomic_check_bw_limit() determines the
pbn_limit of a branch by simply scanning each port on the current branch
device, then uses the last non-zero full_pbn value that it finds. It
then counts the sum of the PBN used on each branch device for that
level, and compares against the full_pbn value it found before.
This is wrong because ports can and will have different PBN limitations
on many hubs, especially since a number of DisplayPort hubs out there
will be clever and only use the smallest link rate required for each
downstream sink - potentially giving every port a different full_pbn
value depending on what link rate it's trained at. This means with our
current code, which max PBN value we end up with is not well defined.
Additionally, we also need to remember when checking bandwidth
limitations that the top-most device in any MST topology is a branch
device, not a port. This means that the first level of a topology
doesn't technically have a full_pbn value that needs to be checked.
Instead, we should assume that so long as our VCPI allocations fit we're
within the bandwidth limitations of the primary MSTB.
We do however, want to check full_pbn on every port including those of
the primary MSTB. However, it's important to keep in mind that this
value represents the minimum link rate /between a port's sink or mstb,
and the mstb itself/. A quick diagram to explain:
MSTB #1
/ \
/ \
Port #1 Port #2
full_pbn for Port #1 → | | ← full_pbn for Port #2
Sink #1 MSTB #2
|
etc...
Note that in the above diagram, the combined PBN from all VCPI
allocations on said hub should not exceed the full_pbn value of port #2,
and the display configuration on sink #1 should not exceed the full_pbn
value of port #1. However, port #1 and port #2 can otherwise consume as
much bandwidth as they want so long as their VCPI allocations still fit.
And finally - our current bandwidth checking code also makes the mistake
of not checking whether something is an end device or not before trying
to traverse down it.
So, let's fix it by rewriting our bandwidth checking helpers. We split
the function into one part for handling branches which simply adds up
the total PBN on each branch and returns it, and one for checking each
port to ensure we're not going over its PBN limit. Phew.
This should fix regressions seen, where we erroneously reject display
configurations due to thinking they're going over our bandwidth limits
when they're not.
Changes since v1:
* Took an even closer look at how PBN limitations are supposed to be
handled, and did some experimenting with Sean Paul. Ended up rewriting
these helpers again, but this time they should actually be correct!
Changes since v2:
* Small indenting fix
* Fix pbn_used check in drm_dp_mst_atomic_check_port_bw_limit()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Sean Paul <seanpaul@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309210131.1497545-1-lyude@redhat.com
We used to punt off reprobing path resources to the link address probe
work, but now that we handle CSNs asynchronously from the driver's HPD
handling we can do whatever the heck we want from the CSN!
So, reprobe the path resources from drm_dp_mst_handle_conn_stat(). Also,
get rid of the path resource reprobing code in
drm_dp_check_and_send_link_address() since it's needlessly complicated
when we already reprobe path resources from
drm_dp_handle_link_address_port(). And finally, teach
drm_dp_send_enum_path_resources() to return 1 on PBN changes so we know
if we need to send another hotplug or not.
This fixes issues where we've indicated to userspace that a port has
just been connected, before we actually probed it's available PBN -
something that results in unexpected atomic check failures.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-4-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
DisplayPort specifications are fun. For a while, it's been really
unclear to us what available_pbn actually does. There's a somewhat vague
explanation in the DisplayPort spec (starting from 1.2) that partially
explains it:
The minimum payload bandwidth number supported by the path. Each node
updates this number with its available payload bandwidth number if its
payload bandwidth number is less than that in the Message Transaction
reply.
So, it sounds like available_pbn represents the smallest link rate in
use between the source and the branch device. Cool, so full_pbn is just
the highest possible PBN that the branch device supports right?
Well, we assumed that for quite a while until Sean Paul noticed that on
some MST hubs, available_pbn will actually get set to 0 whenever there's
any active payloads on the respective branch device. This caused quite a
bit of confusion since clearing the payload ID table would end up fixing
the available_pbn value.
So, we just went with that until commit cd82d82cbc ("drm/dp_mst: Add
branch bandwidth validation to MST atomic check") started breaking
people's setups due to us getting erroneous available_pbn values. So, we
did some more digging and got confused until we finally looked at the
definition for full_pbn:
The bandwidth of the link at the trained link rate and lane count
between the DP Source device and the DP Sink device with no time slots
allocated to VC Payloads, represented as a Payload Bandwidth Number. As
with the Available_Payload_Bandwidth_Number, this number is determined
by the link with the lowest lane count and link rate.
That's what we get for not reading specs closely enough, hehe. So, since
full_pbn is definitely what we want for doing bandwidth restriction
checks - let's start using that instead and ignore available_pbn
entirely.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
It's already prefixed by dp_mst, so we don't really need to repeat
ourselves here. One of the changes I should have picked up originally
when reviewing MST DSC support.
There should be no functional changes here
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Sean Paul <seanpaul@google.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-2-lyude@redhat.com
drm_dp_mst_topology_mgr_cbs.destroy_connector callbacks are identical
amongst every driver and don't do anything other than cleaning up the
connector (drm_connector_unregister()/drm_connector_put()) except for
amdgpu_dm driver where some amdgpu_dm specific code in there which I
an not sure if it should stay or not.
Create and use a helper which calls driver's destroy_connector hook if
available otherwise does cleanup internally.
This is the step towards removing identical hooks from every driver.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-5-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
drm_dp_mst_topology_mgr_cbs.register_connector callbacks are literally
identical amongst every driver and don't do anything other than
calling drm_connector_register(). Hence call drm_connector_register()
directly instead of a callback.
This is the preparatory step for removing the
drm_dp_mst_topology_mgr_cbs.register_connector callback hook.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-2-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
We actually expect this to return a 0 on success, or negative error code
on failure. In order to do that, we check whether or not we managed to
write the whole GUID and then return 0 if so, otherwise return a
negative error code. Also, let's add an error message here so it's a
little more obvious when this fails in the middle of a link address
probe.
This should fix issues with certain MST hubs seemingly stopping for no
reason in the middle of the link address probe process.
Fixes: cb897542c6 ("drm/dp_mst: Fix W=1 warnings")
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234923.547873-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Noticed this while having some problems with hubs sometimes not being
detected on the first plug. Every single dpcd read or write function
returns the number of bytes transferred on success or a negative error
code, except apparently for drm_dp_mst_dpcd_write() - which returns 0 on
success.
There's not really any good reason for this difference that I can tell,
and having the two functions give differing behavior means that
drm_dp_dpcd_write() will end up returning 0 on success for MST devices,
but the number of bytes transferred for everything else.
So, fix that and update the kernel doc.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 2f221a5efe ("drm/dp_mst: Add MST support to DP DPCD R/W functions")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234923.547873-2-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The whole point of using OUIs is so that we can recognize certain
devices and potentially apply quirks for them. Normally this should work
quite well, but there appears to be quite a number of laptop panels out
there that will fill the OUI but not the device ID. As such, for devices
like this I can't imagine it's a very good idea to try relying on OUIs
for applying quirks. As well, some laptop vendors have confirmed to us
that their panels have this exact issue.
So, let's introduce the ability to apply DP quirks based on EDID
identification. We reuse the same quirk bits for OUI-based quirks, so
that callers can simply check all possible quirks using
drm_dp_has_quirk().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211183358.157448-2-lyude@redhat.com
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkEjOgAKCRDj7w1vZxhR
xeaDAQD+1MludG4RmfQhATe4jTsPC1r2x63OF2CA0ChMGHXJyQEA8qqQ+8y1Cd/u
PZ3PpcTl4qYYHgzJ6FwW7kDPTvlaZQE=
=IJAt
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-02-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.7:
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200210093421.xu4sofldm6wm6xq6@gilmour.lan
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5JsVQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHZEH+wddtJO4dZk5TZdF
KZB2w2ldsCvrBZAmas1TVvm8ncvUf+ATUZcSIzvZ3YbLmxsuLF2Cz3kD+n+36Mvy
ejwq8Scl7jwnouYps/Gfd6rRj/uCafqST4qp15GMGeiy2ST4A8dJrv5IAgZhD8/N
SN1bSr1AXpZ2JlEzzLDQ/NdVoNMS6IzCOsaINZcc60/XQoQZFRBWamMJFqu+CmXD
SBJOybQNFJhziy45cGZSAl+67sSCcoPftwTs0Stu4CJsvFWRb3MsbNTDS51Hjcc4
3tdgGOhoNXzyzZr96MEAHmiaW4VLQv0PGgUfOajE35viMz48OrwCTru8Kbuae3XM
YHV4qJk=
=yiem
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkpecgAKCRDj7w1vZxhR
xU4CAQD/8ZzfYroiiEI7FHEgvnuldGYZqA9kbNAO2Vueeac0OgD+Jojewdxy+pJ9
dxfA/POdtzx3hOdN+U1YgaDC0hbXwww=
=XgKq
-----END PGP SIGNATURE-----
Merge v5.6-rc2 into drm-misc-next
Lyude needs some patches in 5.6-rc2 and we didn't bring drm-misc-next
forward yet, so it looks like a good occasion.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
- Revert allow_fb_modifiers in sun4i, as it causes a regression for DE2 and DE3.
- Fix null pointer deref in drm_dp_mst_process_up_req().
-----BEGIN PGP SIGNATURE-----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=VCDX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2020-02-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v5.6:
- Revert allow_fb_modifiers in sun4i, as it causes a regression for DE2 and DE3.
- Fix null pointer deref in drm_dp_mst_process_up_req().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/672810c3-4212-0a46-337b-2cb855573fd2@linux.intel.com
According to DP specification, DP_SINK_EVENT_NOTIFY is also a
broadcast message but as this function only handles
DP_CONNECTION_STATUS_NOTIFY I will only make the static
analyzer that caught this issue happy by not calling
drm_dp_get_mst_branch_device_by_guid() with a NULL guid, causing
drm_dp_mst_process_up_req() to return in the "if (!mstb)" right
bellow.
Fixes: 9408cc94eb ("drm/dp_mst: Handle UP requests asynchronously")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
[added cc to stable]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200129232448.84704-1-jose.souza@intel.com
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes
-----BEGIN PGP SIGNATURE-----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=oFrI
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Davbe Airlie:
"This is the main pull request for graphics for 5.6. Usual selection of
changes all over.
I've got one outstanding vmwgfx pull that touches mm so kept it
separate until after all of this lands. I'll try and get it to you
soon after this, but it might be early next week (nothing wrong with
code, just my schedule is messy)
This also hits a lot of fbdev drivers with some cleanups.
Other notables:
- vulkan timeline semaphore support added to syncobjs
- nouveau turing secureboot/graphics support
- Displayport MST display stream compression support
Detailed summary:
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes"
* tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits)
drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing
drm/nouveau/acr: return error when registering LSF if ACR not supported
drm/nouveau/disp/gv100-: not all channel types support reporting error codes
drm/nouveau/disp/nv50-: prevent oops when no channel method map provided
drm/nouveau: support synchronous pushbuf submission
drm/nouveau: signal pending fences when channel has been killed
drm/nouveau: reject attempts to submit to dead channels
drm/nouveau: zero vma pointer even if we only unreference it rather than free
drm/nouveau: Add HD-audio component notifier support
drm/nouveau: fix build error without CONFIG_IOMMU_API
drm/nouveau/kms/nv04: remove set but not used variable 'width'
drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector'
drm/nouveau/mmu: fix comptag memory leak
drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc
drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping
drm/exynos: Rename Exynos to lowercase
drm/exynos: change callback names
drm/mst: Don't do atomic checks over disabled managers
drm/amdgpu: add the lost mutex_init back
drm/amd/display: skip opp blank or unblank if test pattern enabled
...
The issues caused by:
commit 64e62bdf04 ("drm/dp_mst: Remove VCPI while disabling topology
mgr")
Prompted me to take a closer look at how we clear the payload state in
general when disabling the topology, and it turns out there's actually
two subtle issues here.
The first is that we're not grabbing &mgr.payload_lock when clearing the
payloads in drm_dp_mst_topology_mgr_set_mst(). Seeing as the canonical
lock order is &mgr.payload_lock -> &mgr.lock (because we always want
&mgr.lock to be the inner-most lock so topology validation always
works), this makes perfect sense. It also means that -technically- there
could be racing between someone calling
drm_dp_mst_topology_mgr_set_mst() to disable the topology, along with a
modeset occurring that's modifying the payload state at the same time.
The second is the more obvious issue that Wayne Lin discovered, that
we're not clearing proposed_payloads when disabling the topology.
I actually can't see any obvious places where the racing caused by the
first issue would break something, and it could be that some of our
higher-level locks already prevent this by happenstance, but better safe
then sorry. So, let's make it so that drm_dp_mst_topology_mgr_set_mst()
first grabs &mgr.payload_lock followed by &mgr.lock so that we never
race when modifying the payload state. Then, we also clear
proposed_payloads to fix the original issue of enabling a new topology
with a dirty payload state. This doesn't clear any of the drm_dp_vcpi
structures, but those are getting destroyed along with the ports anyway.
Changes since v1:
* Use sizeof(mgr->payloads[0])/sizeof(mgr->proposed_vcpis[0]) instead -
vsyrjala
Cc: Sean Paul <sean@poorly.run>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122194321.14953-1-lyude@redhat.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/drm_dp_mst_topology.c:3693:16: warning: variable
‘origlen’ set but not used [-Wunused-but-set-variable]
int replylen, origlen, curreply;
It looks like never use variable origlen after assign value to it.
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200118080628.mxcx7bfwdas5m7un@kaowomen.cn
[Why]
While handling LINK_ADDRESS reply, current code expects a peer device
can handle sideband message once the peer device type is reported as
DP_PEER_DEVICE_MST_BRANCHING. However, when the connected device is
a SST branch case, it can't handle the sideband message(MST_CAP=0 in
DPCD 00021h).
Current code will try to send LINK_ADDRESS to SST branch device and end
up with message timeout and monitor can't display normally. As the
result of that, we should take SST branch device into account.
[How]
According to DP 1.4 spec, we can use Peer_Device_Type as
DP_PEER_DEVICE_MST_BRANCHING and Message_Capability_Status as 0 to
indicate peer device as a SST-only branch device.
Fix following:
- Add the function drm_dp_mst_is_dp_mst_end_device() to decide whether a
peer device connected to a DFP is mst end device. Which also indicates
if the peer device is capable of handling message or not.
- Take SST-only branch device case into account in
drm_dp_port_set_pdt() and add a new parameter 'new_mcs'. Take sst branch
device case as the same case as DP_PEER_DEVICE_DP_LEGACY_CONV and
DP_PEER_DEVICE_SST_SINK. All original handling logics remain.
- Take SST-only branch device case into account in
drm_dp_mst_port_add_connector().
- Fix some parts in drm_dp_mst_handle_link_address_port() to have SST
branch device case into consideration.
- Fix the arguments of drm_dp_port_set_pdt() in
drm_dp_mst_handle_conn_stat().
- Have SST branch device also report
connector_status_connected when the ddps is true
in drm_dp_mst_detect_port()
- Fix the arguments of drm_dp_port_set_pdt() in
drm_dp_delayed_destroy_port()
Changes since v1:(https://patchwork.kernel.org/patch/11323079/)
* Squash previous patch into one patch and merge the commit message here.
* Combine the if statements mentioned in comments
Fixes: c485e2c97d ("drm/dp_mst: Refactor pdt setup/teardown, add more locking")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200117060350.26358-2-Wayne.Lin@amd.com
[Why]
Noticed this while testing MST with the 4 ports MST hub from
StarTech.com. Sometimes can't light up monitors normally and get the
error message as 'sideband msg build failed'.
Look into aux transactions, found out that source sometimes will send
out another down request before receiving the down reply of the
previous down request. On the other hand, in drm_dp_get_one_sb_msg(),
current code doesn't handle the interleaved replies case. Hence, source
can't build up message completely and can't light up monitors.
[How]
For good compatibility, enforce source to send out one down request at a
time. Add a flag, is_waiting_for_dwn_reply, to determine if the source
can send out a down request immediately or not.
- Check the flag before calling process_single_down_tx_qlock to send out
a msg
- Set the flag when successfully send out a down request
- Clear the flag when successfully build up a down reply
- Clear the flag when find erros during sending out a down request
- Clear the flag when find errors during building up a down reply
- Clear the flag when timeout occurs during waiting for a down reply
- Use drm_dp_mst_kick_tx() to try to send another down request in queue
at the end of drm_dp_mst_wait_tx_reply() (attempt to send out messages
in queue when errors occur)
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113093649.11755-1-Wayne.Lin@amd.com
[Why]
When change the connection status in a MST topology, mst device
which detect the event will send out CONNECTION_STATUS_NOTIFY messgae.
e.g. src-mst-mst-sst => src-mst (unplug) mst-sst
Currently, under the above case of unplugging device, ports which have
been allocated payloads and are no longer in the topology still occupy
time slots and recorded in proposed_vcpi[] of topology manager.
If we don't clean up the proposed_vcpi[], when code flow goes to try to
update payload table by calling drm_dp_update_payload_part1(), we will
fail at checking port validation due to there are ports with proposed
time slots but no longer in the mst topology. As the result of that, we
will also stop updating the DPCD payload table of down stream port.
[How]
While handling the CONNECTION_STATUS_NOTIFY message, add a detection to
see if the event indicates that a device is unplugged to an output port.
If the detection is true, then iterrate over all proposed_vcpi[] to
see whether a port of the proposed_vcpi[] is still in the topology or
not. If the port is invalid, set its num_slots to 0.
Thereafter, when try to update payload table by calling
drm_dp_update_payload_part1(), we can successfully update the DPCD
payload table of down stream port and clear the proposed_vcpi[] to NULL.
Changes since v1:(https://patchwork.kernel.org/patch/11275801/)
* Invert the conditional to reduce the indenting
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
[removed cc for stable - there's too many patches this depends on for
this to backport cleanly]
Link: https://patchwork.freedesktop.org/patch/msgid/20200106102158.28261-1-Wayne.Lin@amd.com
the parameter is the mst manager, not the port.
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We need to minimally initialize the remote aux channel, e.g. the
crc work struct of remote aux to dump the sink's DPRX CRCs in MST
setup.
[how]
Add helper that only initializes the crc work struct of the remote
aux, hooke crc work queue to 'drm_dp_aux_crc_work'. Then call this
helper in DP MST port initialization.
This, plus David Francis' patch [1], fix the issue of MST remote
aux DPCD CRCs read.
[1] https://patchwork.kernel.org/patch/11217941/
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: David (Dingchen) Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Whenever a connector on an MST network is changed or
undergoes a modeset, the DSC configs for each stream on that
topology will be recalculated. This can change their required
bandwidth, requiring a full reprogramming, as though a modeset
was performed, even if that stream did not change timing.
[how]
Adding helper to trigger modesets on MST DSC connectors
by setting mode_changed flag on CRTCs in the same topology
as affected connector
v2: use drm_dp_mst_dsc_aux_for_port function to verify
if the port is DSC capable
v3: - added _must_check attribute
- removed topology manager check
- fix typos and indentations
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
drm_dp_mst_atomic_check_topology_state() should be renamed
to reflect more specific type of check. Since it is verifying
payload allocation limit it should be renamed into
drm_dp_mst_atomic_check_vcpi_alloc_limit()
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Adding PBN attribute to drm_dp_vcpi_allocation structure to
keep track of how much bandwidth each Port requires.
Adding drm_dp_mst_atomic_check_bw_limit to verify that
state's bandwidth needs doesn't exceed available bandwidth.
The funtion is called in drm_dp_mst_atomic_check after
drm_dp_mst_atomic_check_topology_state to fully verify that
the proposed topology is supported.
v2: Fixing some typos and indenting
v3: Return correct error enums if no bw space available
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding a helper function to be called by
drivers outside of DRM to enable DSC on
the MST ports.
Function is called to recalculate VCPI allocation
if DSC is enabled and raise the DSC flag to enable.
In case of disabling DSC the flag is set to false
and recalculation of VCPI slots is expected to be done
in encoder's atomic_check.
v2: squash separate functions into one and call it per
port
v3: Fix comment typos
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
