Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:699:13-21: Unneeded
variable: "ret_code". Return "0" on line 710
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.
Fix this by dropping the check for number of delay iterations.
While at it, also make __ew32_prepare() static as it's not used
anywhere else.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority
based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES
accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way Rx queue assignment based on mac address, Ethertype and VLAN
priority filtering operates in I225 doesn't allow us to properly support
NFC rules with multiple matches.
Consider the following example which assigns to queue 2 frames matching
the address MACADDR *and* Ethertype ETYPE.
$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2
When such rule is applied, we have 2 unwanted behaviors:
1) Any frame matching MACADDR will be assigned to queue 2. It
doesn't matter the ETYPE value.
2) Any accepted frame that has Ethertype equals to ETYPE, no matter
the mac address, will be assigned to queue 2 as well.
In current code, multiple-match filters are accepted by the driver, even
though it doesn't support them properly. This patch adds a check for
multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are
rejected.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Transmit underrun, late and excess collision flags not in use.
This patch comes to clean up these flags.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit b5f69ccf67 ("ixgbe: avoid bringing rings up/down as macvlans are added/removed")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c:105:2-38: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No need to convert '==' expression to bool. This fixes the following
coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:68:11-16: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The comment above i40e_run_xdp_zc() was clearly copy-pasted from
function i40e_xsk_umem_setup, which is just above.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling hclge_parse_speed() fails, printing out the speed is
helpful for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some fields in struct hclge_dev which have not been used.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_CMDQ_INTR_SRC_REG and HCLGEVF_CMDQ_INTR_STS_REG are same
as HCLGEVF_VECTOR0_CMDQ_SRC_REG and HCLGEVF_VECTOR0_CMDQ_STAT_REG,
replace the former with the latter, and rename macro
HCLGEVF_VECTOR0_CMDQ_STAT_REG since 'stat' is not abbreviation of
'state'.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since field .uinfo in struct hnae3_handle never be used,
so remove it and its structure definition.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove HNAE3_RESTORE_CLIENT which is not needed now.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some fileds which defined in struct hns3_nic_priv,
but not used, and remove the related definition of struct
hns3_udp_tunnel and enum hns3_udp_tnl_type.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify field .gro_en in struct hclgevf_cfg_gro_status_cmd to u8
according to the UM, otherwise, it will overwrite the reserved
byte which may be used for other purpose.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify field .gro_en in struct hclge_cfg_gro_status_cmd to u8
according to the UM, otherwise, it will overwrite the reserved
byte which may be used for other purpose.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve code maintainability and readability, rewrite
the process of BDs' initialization in hclge_query_bd_num_cmd_send().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since parameters 'tso_mss_min' and 'tso_mss_max' only indicate
the minimum and maximum MSS, the hnae3_set_field() calls are
meaningless, remove them and change the type of these two
parameters to u16.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mutex destroy call in hclge_init_ae_dev() when fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the redundant 'goto' and return -ENOMEM directly, when
allocating memory for 'hdev' fails in hclge_init_ae_dev().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851_mll.c is replaced by ks8851_par.c, which is using common code
from ks8851.c, just like ks8851_spi.c . Remove this old ad-hoc driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement accessors for KS8851-16MLL/MLLI/MLLU parallel bus variant of
the KS8851. This is based off the ks8851_mll.c , which is a driver for
exactly the same hardware, however the ks8851.c code is much higher
quality. Hence, this patch pulls out the relevant information from the
ks8851_mll.c on how to access the bus, but uses the common ks8851.c
code. To make this patch reviewable, instead of rewriting ks8851_mll.c,
ks8851_mll.c is removed in a separate subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull all the SPI bus specific code into a separate file, so that it is
not mixed with the common code. Rename ks8851.c to ks8851_common.c. The
ks8851_common.c is linked with ks8851_spi.c now, so it can call the
accessors in the ks8851_spi.c without any pointer indirection.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register and FIFO accessors are bus specific, so is locking.
Implement callbacks so that each variant of the KS8851 can implement
matching accessors and locking, and use the rest of the common code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parallel bus variant does not need to use the TX interrupt at all
as it writes the TX FIFO directly with in .ndo_start_xmit, permit the
drivers to configure the interrupt enable bits.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the SPI version of the KS8851 requires a TX worker thread to pump
data via SPI, the parallel bus version can write data into the TX FIFO
directly in .ndo_start_xmit, as the parallel bus access is much faster
and does not sleep. Factor out this TX work flush part, so it can be
overridden by the parallel bus driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code into ks8851_probe_common() and
ks8851_remove_common() to permit both SPI and parallel
bus driver variants to use the common code path for
both probing and removal.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new struct ks8851_net_spi, which embeds the original
struct ks8851_net and contains the entries specific only to
the SPI variant of KS8851.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out this netif_rx_ni(), so it could be overridden by the parallel
bus variant of the KS8851 driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out bus access locking code into separate functions, this is done
in preparation for unifying the driver with the parallel bus one. The
parallel bus driver does not need heavy mutex locking of the bus and
works better with spinlocks, hence prepare these locking functions to
be overridden then.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RXFC register is the only one being read using 8-bit accessors.
To make it easier to support the 16-bit accesses used by the parallel
bus variant of KS8851, use 16-bit accessor to read RXFC register as
well as neighboring RXFCTR register.
Remove ks8851_rdreg8() as it is not used anywhere anymore.
There should be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the SPI variant of KS8851, the MAC address can be programmed with
either 8/16/32-bit writes. To make it easier to support the 16-bit
parallel option of KS8851 too, switch both the MAC address programming
and readout to 16-bit operations.
Remove ks8851_wrreg8() as it is not used anywhere anymore.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851_rdreg32() is used only in one place, to read two registers
using a single read. To make it easier to support 16-bit accesses via
parallel bus later on, replace this single read with two 16-bit reads
from each of the registers and drop the ks8851_rdreg32() altogether.
If this has noticeable performance impact on the SPI variant of KS8851,
then we should consider using regmap to abstract the SPI and parallel
bus options and in case of SPI, permit regmap to merge register reads
of neighboring registers into single, longer, read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which
works for both SPI and platform drivers. This is done in preparation
for unifying the KS8851 SPI and parallel bus drivers.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device managed version of alloc_etherdev() to simplify the code.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver probe function already has a struct device *dev pointer
and can easily derive of_node pointer from it, pass the of_node pointer as
a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev.
This is the only reference to spidev in the function, so get rid of it.
This is done in preparation for unifying the KS8851 SPI and parallel bus
drivers.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev
in the interrupt handler. This is the only place which uses the spidev
in this function, so replace it with netdev_err() to get rid of it. This
is done in preparation for unifying the KS8851 SPI and parallel drivers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ndev variable to netdev for the sake of consistency.
No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out the spi->dev into one common place in the function instead of
having it repeated over and over again. This is done in preparation for
unifying ks8851 and ks8851-mll drivers. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'nic_data' is no longer used outside of the #ifdef block
in efx_ef10_set_mac_address:
drivers/net/ethernet/sfc/ef10.c:3231:28: error: unused variable 'nic_data' [-Werror,-Wunused-variable]
struct efx_ef10_nic_data *nic_data = efx->nic_data;
Move the variable into a local scope.
Fixes: dfcabb0788 ("sfc: move vport_id to struct efx_nic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-27
This series contains updates to the ice driver only.
Jesse fixes a number of issues, starting with fixing the remaining
signed versus unsigned comparison issues. Cleaned up an unused code
define. Fixed the implementation of the manage MAC write command, to
simplify it by using a simple array to represent the MAC address when
writing it.
Paul fixes the setting of the VF default LAN address, by removing a
check that assumed that the address had been deleted and zeroed.
Surabhi prevents a memory leak on filter management initialization
failures and during queue initialization and buffer allocation failures.
Brett adds additional receive error counters that are reported by
ethtool. Fixed the enabling and disabling of VLAN stripping when the
PVID has been set.
Evan fixes a race condition between the firmware and software, which can
occur between the admin queue setup and the first command sent.
Marta fixes the driver when XDP transmit rings are destroyed, also make
sure the XDP transmit queues are also destroyed. Update the statistics
when XDP transmit programs are loaded and packets are sent. Changed the
number of XDP transmit queues to match the number of receive queues,
instead of matching the number of transmit queues.
Bruce avoids undefined behavior by not writing the 8-bit element
init_q_state with the associated internal-to-hardware field which is
122-bits.
Anirudh (Ani) refactors the receive checksum checks.
Krzysztof notifies the user if the fill queue is not long enough to
prepare all buffers before packet processing starts and allocates the
buffers during the NAPI poll.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates highlights:
1) From Vu Pham (8): Support VM traffics failover with bonded VF
representors and e-switch egress/ingress ACLs
This series introduce the support for Virtual Machine running I/O
traffic over direct/fast VF path and failing over to slower
paravirtualized path using the following features:
__________________________________
| VM _________________ |
| |FAILOVER device | |
| |________________| |
| | |
| ____|_____ |
| | | |
| ______ |___ ____|_______ |
| | VF PT | |VIRTIO-NET | |
| | device | | device | |
| |_________| |___________| |
|___________|______________|________|
| |
| HYPERVISOR |
| ____|______
| | macvtap |
| |virtio BE |
| |___________|
| |
| ____|_____
| |host VF |
| |_________|
| |
_____|______ _____|_____
| PT VF | | host VF |
|representor| |representor|
|___________| |___________|
\ /
\ /
\ /
\ / _________________
\_______/ | |
_______|________ | V-SWITCH |
|VF representors |________________| (OVS) |
| bond | |________________|
|________________| |
________|________
| Uplink |
| representor |
|_________________|
Summary:
--------
Problem statement:
------------------
Currently in above topology, when netfailover device is configured using
VFs and eswitch VF representors, and when traffic fails over to stand-by
VF which is exposed using macvtap device to guest VM, eswitch fails to
switch the traffic to the stand-by VF representor. This occurs because
there is no knowledge at eswitch level of the stand-by representor
device.
Solution:
---------
Using standard bonding driver, a bond netdevice is created over VF
representor device which is used for offloading tc rules.
Two VF representors are bonded together, one for the passthrough VF
device and another one for the stand-by VF device.
With this solution, mlx5 driver listens to the failover events
occuring at the bond device level to failover traffic to either of
the active VF representor of the bond.
a. VM with netfailover device of VF pass-thru (PT) device and virtio-net
paravirtualized device with same MAC-address to handle failover
traffics at VM level.
b. Host bond is active-standby mode, with the lower devices being the VM
VF PT representor, and the representor of the 2nd VF to handle
failover traffics at Hypervisor/V-Switch OVS level.
- During the steady state (fast datapath): set the bond active
device to be the VM PT VF representor.
- During failover: apply bond failover to the second VF representor
device which connects to the VM non-accelerated path.
c. E-Switch ingress/egress ACL tables to support failover traffics at
E-Switch level
I. E-Switch egress ACL with forward-to-vport rule:
- By default, eswitch vport egress acl forward packets to its
counterpart NIC vport.
- During port failover, the egress acl forward-to-vport rule will
be added to e-switch vport of passive/in-active slave VF
representor
to forward packets to other e-switch vport ie. the active slave
representor's e-switch vport to handle egress "failover"
traffics.
- Using lower change netdev event to detect a representor is a
lower
dev (slave) of bond and becomes active, adding egress acl
forward-to-vport rule of all other slave netdevs to forward to
this
representor's vport.
- Using upper change netdev event to detect a representor unslaving
from bond device to delete its vport's egress acl forward-to-vport
rule.
II. E-Switch ingress ACL metadata reg_c for match
- Bonded representors' vorts sharing tc block have the same
root ingress acl table and a unique metadata for match.
- Traffics from both representors's vports will be tagged with same
unique metadata reg_c.
- Using upper change netdev event to detect a representor
enslaving/unslaving from bond device to setup shared root ingress
acl and unique metadata.
2) From Alex Vesker (2): Slpit RX and TX lock for parallel rule insertion in
software steering
3) Eli Britstein (2): Optimize performance for IPv4/IPv6 ethertype use the HW
ip_version register rather than parsing eth frames for ethertype.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7PEFAACgkQSD+KveBX
+j4Z5Af+NYwihYZpQYBBN00K7Wu10XZ65u5MbGSDmzpdN62w0kKfjsJ70bb9aiws
h8LC7lspdMLRMMn9pWwFKshyF6RoSD9Ku3ZYhUbtj+hJLElAd9IwGt6pPKr8hPDd
9h+ZcBkacdhNwWKf7CKThic0c/0PLdVyzRysHxcQWKSMPCTdgiL5Z3PQHA0TM6J3
6Excs2z7kSuuyyxQ1cyWCaqSz4rqCrYyd8Ws4HOPhXgSbX14Q3mtMsBDayx2gHNW
rdVbaNN6s2o0TxbrCwd0AaNP3UWcnjNqu1ohxgJiSe8y+MHMoB0OMoO+6vQJnwNI
bzpZEioswV1zdgK3qNmXqbHOiHRSVQ==
=xM1D
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-05-26
Updates highlights:
1) From Vu Pham (8): Support VM traffics failover with bonded VF
representors and e-switch egress/ingress ACLs
This series introduce the support for Virtual Machine running I/O
traffic over direct/fast VF path and failing over to slower
paravirtualized path using the following features:
__________________________________
| VM _________________ |
| |FAILOVER device | |
| |________________| |
| | |
| ____|_____ |
| | | |
| ______ |___ ____|_______ |
| | VF PT | |VIRTIO-NET | |
| | device | | device | |
| |_________| |___________| |
|___________|______________|________|
| |
| HYPERVISOR |
| ____|______
| | macvtap |
| |virtio BE |
| |___________|
| |
| ____|_____
| |host VF |
| |_________|
| |
_____|______ _____|_____
| PT VF | | host VF |
|representor| |representor|
|___________| |___________|
\ /
\ /
\ /
\ / _________________
\_______/ | |
_______|________ | V-SWITCH |
|VF representors |________________| (OVS) |
| bond | |________________|
|________________| |
________|________
| Uplink |
| representor |
|_________________|
Summary:
--------
Problem statement:
------------------
Currently in above topology, when netfailover device is configured using
VFs and eswitch VF representors, and when traffic fails over to stand-by
VF which is exposed using macvtap device to guest VM, eswitch fails to
switch the traffic to the stand-by VF representor. This occurs because
there is no knowledge at eswitch level of the stand-by representor
device.
Solution:
---------
Using standard bonding driver, a bond netdevice is created over VF
representor device which is used for offloading tc rules.
Two VF representors are bonded together, one for the passthrough VF
device and another one for the stand-by VF device.
With this solution, mlx5 driver listens to the failover events
occuring at the bond device level to failover traffic to either of
the active VF representor of the bond.
a. VM with netfailover device of VF pass-thru (PT) device and virtio-net
paravirtualized device with same MAC-address to handle failover
traffics at VM level.
b. Host bond is active-standby mode, with the lower devices being the VM
VF PT representor, and the representor of the 2nd VF to handle
failover traffics at Hypervisor/V-Switch OVS level.
- During the steady state (fast datapath): set the bond active
device to be the VM PT VF representor.
- During failover: apply bond failover to the second VF representor
device which connects to the VM non-accelerated path.
c. E-Switch ingress/egress ACL tables to support failover traffics at
E-Switch level
I. E-Switch egress ACL with forward-to-vport rule:
- By default, eswitch vport egress acl forward packets to its
counterpart NIC vport.
- During port failover, the egress acl forward-to-vport rule will
be added to e-switch vport of passive/in-active slave VF
representor
to forward packets to other e-switch vport ie. the active slave
representor's e-switch vport to handle egress "failover"
traffics.
- Using lower change netdev event to detect a representor is a
lower
dev (slave) of bond and becomes active, adding egress acl
forward-to-vport rule of all other slave netdevs to forward to
this
representor's vport.
- Using upper change netdev event to detect a representor unslaving
from bond device to delete its vport's egress acl forward-to-vport
rule.
II. E-Switch ingress ACL metadata reg_c for match
- Bonded representors' vorts sharing tc block have the same
root ingress acl table and a unique metadata for match.
- Traffics from both representors's vports will be tagged with same
unique metadata reg_c.
- Using upper change netdev event to detect a representor
enslaving/unslaving from bond device to setup shared root ingress
acl and unique metadata.
2) From Alex Vesker (2): Slpit RX and TX lock for parallel rule insertion in
software steering
3) Eli Britstein (2): Optimize performance for IPv4/IPv6 ethertype use the HW
ip_version register rather than parsing eth frames for ethertype.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a UMEM is present on a queue when an interface/queue pair is being
enabled, the driver will try to prepare the Rx buffers in advance to
improve performance. However, if fill queue is shorter than HW Rx ring,
the driver will report failure after getting the last address from the
fill queue.
This still lets the driver process the packets correctly during the NAPI
poll, but leads to a constant NAPI rescheduling. Not allocating the
buffers in advance would result in a potential performance decrease.
Commit d57d76428a ("xsk: Add API to check for available entries in FQ")
provides an API that lets drivers check the number of addresses that the
fill queue holds.
Notify the user if fill queue is not long enough to prepare all buffers
before packet processing starts, and allocate the buffers during the
NAPI poll. If the fill queue size is sufficient, prepare Rx buffers in
advance.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the locking flow to support RX and TX locks, splitting
the single lock to two will allow inserting rules in parallel
for RX and TX parts of the FDB.
Locking the dr_domain will be done by locking the RX domain
and the TX domain locks, this is mostly used for control operations
on the dr_domain. When inserting rules for RX or TX the single
nic_doamin RX or TX lock will be used. Splitting the lock is safe since
RX and TX domains are logically separated from each other, shared
objects such the send-ring and memory pool are protected by locks.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding this lock will allow writing steering entries without
locking the dr_domain and allow parallel insertion.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
