Cleanup the .driver setup to just do it once, to avoid
the following sparse warning:
drivers/net/ethernet/calxeda/xgmac.c:1914:10: warning: Initializer entry defined twice
drivers/net/ethernet/calxeda/xgmac.c:1920:10: also defined here
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
mac_delay value will be divided by 550/170 in mt2712_delay_ps2stage(),
which is invoked at the beginning of mt2712_set_delay(), and the value
should be restored at the end of mt2712_set_delay().
Or, mac_delay will be divided again when invoking mt2712_set_delay()
when resume back.
So, add mt2712_delay_stage2ps() to mt2712_set_delay() to recovery the
original mac_delay value.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
All the registers and the functionalities used in the callback
dwmac5_flex_pps_config() are common between dwmac 4.10a [1] and
5.00a [2].
Reuse the same callback for dwmac 4.10a too.
Tested on STM32MP15x, based on dwmac 4.10a.
[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The hardware supports up to 8 TX BD for non-tso skb and up to
63 TX BD for TSO skb. Currently, the hns3 driver supports RX skb
with fraglist when HW GRO is enabled, when the stack forwards a
RX skb with fraglist, the stack need to linearize the skb before
sending to other interface without TX fraglist support.
This patch adds support for TX fraglist. The performance increases
from 1 GByte to 1.5 GByte for one iperf TCP stream during
forwarding test after this patch. BTW, the minimum BD number of
ring should be updated to 72 for supporting TX fraglist.
This patch also changes the error handling of some function that
called by hns3_fill_desc, which returns BD num when there is no
error, change some macro to more meaningful name.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support of configuring VF MAC from the host
for the HNS3 driver.
BTW, the parameter init in the hns3_init_mac_addr is
unnecessary now, since the MAC address will not read from
NCL_CONFIG when doing reset, so it should be removed,
otherwise it will affect VF's MAC address initialization.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.
For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:
'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status
'ip link show'
show the setting status
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Don't populate the array exp_mask on the stack but instead make it
static. Makes the object code smaller by 224 bytes.
Before:
text data bss dec hex filename
77832 2290 0 80122 138fa ethernet/netronome/nfp/bpf/jit.o
After:
text data bss dec hex filename
77544 2354 0 79898 1381a ethernet/netronome/nfp/bpf/jit.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.
Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.
Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't print error message for a successful return value.
Fixes: d84c3a4ded ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one function call whose result was not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array tick_array on the stack but instead make it
static. Makes the object code smaller by 29 bytes.
Before:
text data bss dec hex filename
19191 432 0 19623 4ca7 hisilicon/hns3/hns3pf/hclge_tm.o
After:
text data bss dec hex filename
19098 496 0 19594 4c8a hisilicon/hns3/hns3pf/hclge_tm.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the arrays port_map and sl_map on the stack but
instead make them static. Makes the object code smaller by 64 bytes.
Before:
text data bss dec hex filename
49575 6872 64 56511 dcbf hisilicon/hns/hns_dsaf_main.o
After:
text data bss dec hex filename
49350 7032 64 56446 dc7e hisilicon/hns/hns_dsaf_main.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set channels callback enables the user to change the count of queues
used by the driver using ethtool. We decided to currently support only
equal number of rx and tx queues, this might change in the future.
Also rename dev_up to dev_was_up in ena_update_queue_count() to make
it clearer.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of queues can be derived using ethtool, no need to print
it in ena_probe()
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update ena_ethtool:ena_get_channels() to return adapter->max_io_queues
so that ethtool -l returns the correct maximum queue number.
- Change the name of ena_calc_io_queue_num() to
ena_calc_max_io_queue_num() as it returns the maximum number of io
queues and actual number of queues can be smaller if changed
by ethtool -L which is implemented in a later commit.
- Change variable name from io_queue_num to max_num_io_queues in
ena_calc_max_io_queue_num() and ena_probe().
- Make all types of variables that convey the number and sizeof queues
to be u32, for consistency with the API between the driver and the
device.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use the same IRQ and NAPI to service RX and TX then we need to
use a combined channel instead of rx and tx channels.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rename ena_calc_queue_size() to ena_calc_io_queue_size() for clarity
and consistency
- Remove redundant number of io queues parameter in functions
ena_enable_msix() and ena_enable_msix_and_set_admin_interrupts(),
which already get adapter parameter, so use adapter->num_io_queues
in the function instead.
- Use the local variable ena_dev instead of ctx->ena_dev in
ena_calc_io_queue_size
- Fix multi row comment alignments
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most places in the code refer to the IO queues as io_queues and not
simply queues. Examples - max_io_queues_per_vf, ENA_MAX_NUM_IO_QUEUES,
ena_destroy_all_io_queues() etc..
We are also adding the new max_num_io_queues field to struct ena_adapter
in the following commit.
The changes included in this commit are:
struct ena_adapter->num_queues => struct ena_adapter->num_io_queues
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores support Layer 3 and Layer 4 filtering. Add the
corresponding callbacks in these cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new tests for VLAN Perfect Filtering. While at it, increase a
little bit the tests strings lenght so that we can have more descriptive
test names.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VLAN Hash Filtering is not available we can fallback to perfect
filtering instead. Let's implement this in XGMAC and GMAC cores and let
the user use this filter.
VLAN VID=0 always passes filter so we check if more than 2 VLANs are
created and return proper error code if so because perfect filtering
only supports 1 VID at a time.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add validation for FW version in order to prevent driver initialization
in case FW version is older than expected. FW version validation is
necessary, because use of a new field 'num_of_modules' in MGPIR register
is not backward compatible. FW 'minor' and 'subminor' versions are
expected to be greater than or equal to 2000 and 1886, respectively.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new API for FW "minor" and "subminor" version validation for
sharing it between "spectrum" and "minimal" drivers.
Use it in "spectrum" driver.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field "num_of_modules" of MGPIR register for "thermal" interface
in order to get the number of modules supported by system directly from
the system configuration, instead of getting it from port to module
mapping info.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field "num_of_modules" of MGPIR register for "hwmon" interface
in order to get the number of modules supported by system directly from
the system configuration, instead of getting it from port to module
mapping info.
Reading this info through MGPIR register is faster and does not depend
on possible dynamic re-configuration of ports.
In case of port dynamic re-configuration some modules can logically
"disappear" as a result of port split and un-spilt operations, which
can cause missing of some modules, in case this info is taken from port
to module mapping info.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend MGPIR - Management General Peripheral Information Register
with new field "num_of_modules" exposing the number of modules
supported by specific system.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracing of device-related interaction to aid performance
analysis, especially around resync:
tls:tls_device_offload_set
tls:tls_device_rx_resync_send
tls:tls_device_rx_resync_nh_schedule
tls:tls_device_rx_resync_nh_delay
tls:tls_device_tx_resync_req
tls:tls_device_tx_resync_send
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.
Fixes: 0f8ab89e82 ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.
Fixes: 94cdb8bb99 ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the devlink reaload the extack is present, so propagate it all
the way down to register_fib_notifier() call in spectrum_router.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating netdevices for ports, put them under network namespace
that the core/parent devlink belongs to.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up patch is going to allow to reload devlink instance into
different network namespace, so use devlink_net() helper instead
of init_net.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if info->extack is NULL, mlxsw assumes that the event came
down from dump. Originally, the dump did not propagate the return value
back to the original caller (fib_notifier_register()). However, that is
now happening. So benefit from this and push the error up if it happened.
Remove rule cases in work handlers that are now dead code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlxsw distributes sent traffic among all the available send
queues. That includes control traffic as well as EMADs, which are used for
configuration of the device.
However because all the queues have the same traffic class of 3, they all
end up being directed to the same traffic class buffer. If the control
traffic in the buffer cannot be serviced quickly enough, the EMAD traffic
might be shut out, which causes transient failures, typically in FDB
maintenance, counter upkeep and other periodic work.
To address this issue, dedicate SDQ 0 to EMAD traffic, with TC 0.
Distribute the control traffic among the remaining queues, which are left
with their current TC 3.
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address width of the controller can be read from hardware feature
registers much like on XGMAC. Add support for parsing the ADDR64 field
so that the DMA mask can be set accordingly.
This avoids getting swiotlb involved for DMA on Tegra186 and later.
Also make sure that the upper 32 bits of the DMA address are written to
the DMA descriptors when enhanced addressing mode is used. Similarily,
for each channel, the upper 32 bits of the DMA descriptor ring's base
address also need to be programmed to make sure the correct memory can
be fetched when the DMA descriptor ring is located beyond the 32-bit
boundary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhanced addressing mode is only required when more than 32 bits need to
be addressed. Add a DMA configuration parameter to enable this mode only
when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver will try to acquire its private mutex during suspend
via phylink_resolve() -> stmmac_mac_link_down() -> stmmac_eee_init().
However, the phylink configuration is updated with the private mutex
held already, which causes a deadlock during suspend.
Fix this by moving the phylink configuration updates out of the region
of code protected by the private mutex.
Fixes: 19e13cb27b ("net: stmmac: Hold rtnl lock in suspend/resume callbacks")
Suggested-by: Bitan Biswas <bbiswas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recycling in mvpp2 has gone long time ago, but two comment still refers
to it. Remove those two misleading comments as they generate confusion.
Fixes: 7ef7e1d949 ("net: mvpp2: drop useless fields in mvpp2_bm_pool and related code")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though we've already turned off the queue activity with
the ionic_qcq_disable(), we need to wait for any device queues
that are processing packets to drain down before we try to
flush our packets and tear down the queues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wire up the --set-fec and --show-fec features in the ethtool
callbacks and pull the related code out of set_link_ksettings.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user's request for an interrupt coalescing value gets
translated into a hardware value to be used with the NIC,
and was getting reported back based on the hw value, which,
due to hw tic resolution, could be reported as a different
number than what the user originally asked for. This code
now tracks both the user request and what was put into the
hardware so we can report back to the user what they
requested.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the open-coded ionic_wait_for_bit() with the
kernel's wait_on_bit_lock().
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
