* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: fix poll_controller to pass proper structures and check all rx queues
niu: Fix readq implementation when architecture does not provide one.
hostap: pad the skb->cb usage in lieu of a proper fix
rtl8187 : support for Sitecom WL-168 0001 v4
mac80211: fix notify_mac function
rtl8187: Add Abocom USB ID
net: put_cmsg_compat + SO_TIMESTAMP[NS]: use same name for value as caller
tcp_htcp: last_cong bug fix
[netdrvr] smc911x: fix for driver resume (and compilation warning)
RDMA/cxgb3: deadlock in iw_cxgb3 can cause hang when configuring interface.
cxgb3 - Limit multiqueue setting to msi-x
cxgb3 - eeprom read fixes
myri10ge: fix stop/go ordering even more
Fix bnx2 so that netpoll works properly. Specifically:
1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a
struct net_device
2) Fix poll_controller method to check every queue in the rx case so frames
aren't missed
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a TX hang reported by Jesper Dangaard Brouer.
When an architecutre cannot provide a fully functional
64-bit atomic readq/writeq, the driver must implement
it's own. This is because only the driver can say whether
doing something like using two 32-bit reads to implement
the full 64-bit read will actually work properly.
In particular one of the issues is whether the top 32-bits
or the bottom 32-bits of the 64-bit register should be read
first. There could be side effects, and in fact that is
exactly the problem here.
The TX_CS register has counters in the upper 32-bits and
state bits in the lower 32-bits. A read clears the state
bits.
We would read the counter half before the state bit half.
That first read would clear the state bits, and then the
driver thinks that no interrupts are pending because the
interrupt indication state bits are seen clear every time.
Fix this by reading the bottom half before the upper half.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like mac80211 did, this driver makes 'clever' use of skb->cb to pass
information along with an skb as it is requeued from the virtual device
to the physical wireless device. Unfortunately, that trick no longer
works...
Unlike mac80211, code complexity and driver apathy makes this hack
the best option we have in the short run. Hopefully someone will
eventually be motivated to code a proper fix before all the effected
hardware dies.
(Above text by me. Johannes officially disavows all knowledge of this
hack. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's
RTL8187B and work fine with new 2.6.27 driver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: struct device - replace bus_id with dev_name(), dev_set_name()
iop-adma: use iop_paranoia() for debug BUG_ONs
iop-adma: add a dummy read to flush next descriptor update
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix crash in path_rec_completion()
IPoIB: Fix hang in ipoib_flush_paths()
IPoIB: Don't enable NAPI when it's already enabled
RDMA/cxgb3: Fix deadlock in iw_cxgb3 (hang when configuring interface)
IB/ehca: Remove reference to special QP in case of port activation failure
IB/mlx4: Set umem field to NULL in mlx4_ib_alloc_fast_reg_mr()
mlx4_core: Fix unused variable warning
RDMA/nes: Mitigate compatibility issue regarding PCIe write credits
RDMA/nes: Fix CQ allocation scheme for multicast receive queue apps
RDMA/nes: Correct handling of PBL resources
RDMA/nes: Reindent mis-indented spinlocks
RDMA/cxgb3: Fix too-big reserved field zeroing in iwch_post_zb_read()
IB/ipath: Fix RDMA write with immediate copy of last packet
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (47 commits)
ACPI: pci_link: remove acpi_irq_balance_set() interface
fujitsu-laptop: Add DMI callback for Lifebook S6420
ACPI: EC: Don't do transaction from GPE handler in poll mode.
ACPI: EC: lower interrupt storm treshold
ACPICA: Use spinlock for acpi_{en|dis}able_gpe
ACPI: EC: restart failed command
ACPI: EC: wait for last write gpe
ACPI: EC: make kernel messages more useful when GPE storm is detected
ACPI: EC: revert msleep patch
thinkpad_acpi: fingers off backlight if video.ko is serving this functionality
sony-laptop: fingers off backlight if video.ko is serving this functionality
msi-laptop: fingers off backlight if video.ko is serving this functionality
fujitsu-laptop: fingers off backlight if video.ko is serving this functionality
eeepc-laptop: fingers off backlight if video.ko is serving this functionality
compal: fingers off backlight if video.ko is serving this functionality
asus-acpi: fingers off backlight if video.ko is serving this functionality
Acer-WMI: fingers off backlight if video.ko is serving this functionality
ACPI video: if no ACPI backlight support, use vendor drivers
ACPI: video: Ignore devices that aren't present in hardware
Delete an unwanted return statement at evgpe.c
...
Fix a crash in path_rec_completion() during an SM up/down loop. If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)". This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path. Having two queries on the same
path leads to a crash.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path(). Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all. Fix this by
completing path->done if issuing the query fails.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable(). ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().
Fix this by moving the call to napi_enable() to after the test for
P_Key presence.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops
get_drvinfo function in cxgb3 to get the fw version and other info.
Currently the iwarp driver grabs the rtnl lock around this down call
to serialize. As of 2.6.27 or so, things changed such that the rtnl
lock is held around the call to the netdev driver open function. Also
the cxgb3_client "add" function doesn't get called if the device is
down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the
device, the iw_cxgb3 add func gets called with the rtnl_lock held. If
you load cxgb3, ifconfig up the device, then load iw_cxgb3, the add
func gets called without the rtnl_lock held. The former causes the
deadlock, the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call down
into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Lifebook S6420 is the ICH9M-based follow-up to the S6410. The application panel
contains the following keys: lock, mobility center, eco, info.
Whilst key 4 might be more appropriate for help then key 2, I've done things the
S6410 way. I can confirm that backlight control is functional, and that the lock key
activates the Gnome screensaver as expected.
Signed-off-by: Tony Vroon <tony@linx.net>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>
If the initialization of a special QP (e.g. AQP1) fails due to a
software timeout, we have to remove the reference to that special QP
struct from the port struct to stop the driver from accessing the QP,
since it will be/has been destroyed by the caller, eg in this case
ib_mad.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Disabling gpe might interfere with gpe detection/handling,
thus producing "interrupt not handled" errors.
Ironically, disabling of GPE from interrupt context is already
under spinlock, so only userspace needs to start using it.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Restart current transaction if we recieved unexpected GPEs instead
of needed ones.
http://bugzilla.kernel.org/show_bug.cgi?id=11896
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a possibility that EC might break if next command is
issued within 1 us after write or burst-disable command.
Suggestd-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure we can tell if the GPE storm workaround gets activated,
and avoid flooding the logs afterwards.
http://bugzilla.kernel.org/show_bug.cgi?id=11841
"plenty of line "ACPI: EC: non-query interrupt received,
switching to interrupt mode" in dmesg"
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the critical read back to flush the next descriptor address is
fixed we can downgrade some BUG_ONs that need only be enabled when testing
changes to the driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The current dummy read references the wrong address allowing the next
descriptor address update to linger in the store buffer and get passed
by an 'append' event.
This issue was uncovered by the change from strongly-ordered to device
memory for the adma registers.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (35 commits)
V4L/DVB (9516): cx18: Move DVB buffer transfer handling from irq handler to work_queue
V4L/DVB (9557): gspca: Small changes for the sensor HV7131B in zc3xx.
V4L/DVB (9556): gspca: Bad init sequence for sensor HV7131B in zc3xx.
V4L/DVB (9549): gspca: Fix a typo in one of gspca chips name.
V4L/DVB (9515): cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup
V4L/DVB (9493): kconfig patch
V4L/DVB (9527): af9015: fix compile warnings
V4L/DVB (9524): af9013: fix bug in status reading
V4L/DVB (9511): cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call
V4L/DVB (9510): cx18: Fix write retries for registers that always change - part 2.
V4L/DVB (9506): ivtv/cx18: fix test whether modules should be loaded or not.
V4L/DVB (9499): cx88-mpeg: final fix for analogue only compilation + de-alloc fix
V4L/DVB (9496): cx88-blackbird: bugfix: cx88-blackbird-mpeg-users
V4L/DVB (9495): cx88-blackbird: bugfix: cx88-blackbird-poll-fix
V4L/DVB (9494): anysee: initialize anysee_usb_mutex statically
V4L/DVB (9492): unplug oops from dvb_frontend_init...
V4L/DVB (9486): ivtv/ivtvfb: no longer experimental
V4L/DVB (9485): ivtv: remove incorrect V4L1 & tvaudio dependency
V4L/DVB (9482): Documentation, especially regarding audio and informational links
V4L/DVB (9475): cx18: Disable write retries for registers that always change - part 1.
...
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Move legacy breadcrumb out of the reserved status page area
drm/i915: Filter pci devices based on PCI_CLASS_DISPLAY_VGA
drm/radeon: map registers at load time
drm: Remove infrastructure for supporting i915's vblank swapping.
i915: Remove racy delayed vblank swap ioctl.
i915: Don't whine when pci_enable_msi() fails.
i915: Don't attempt to short-circuit object_wait_rendering by checking domains.
i915: Clean up sarea pointers on leavevt
i915: Save/restore MCHBAR_RENDER_STANDBY on GM965/GM45
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
dsa: fix master interface allmulti/promisc handling
dsa: fix skb->pkt_type when mac address of slave interface differs
net: fix setting of skb->tail in skb_recycle_check()
net: fix /proc/net/snmp as memory corruptor
mac80211: fix a buffer overrun in station debug code
netfilter: payload_len is be16, add size of struct rather than size of pointer
ipv6: fix ip6_mr_init error path
[4/4] dca: fixup initialization dependency
[3/4] I/OAT: fix async_tx.callback checking
[2/4] I/OAT: fix dma_pin_iovec_pages() error handling
[1/4] I/OAT: fix channel resources free for not allocated channels
ssb: Fix DMA-API compilation for non-PCI systems
SSB: hide empty sub menu
vlan: Fix typos in proc output string
[netdrvr] usb/hso: Cleanup rfkill error handling
sfc: Correct address of gPXE boot configuration in EEPROM
el3_common_init() should be __devinit, not __init
hso: rfkill type should be WWAN
mlx4_en: Start port error flow bug fix
af_key: mark policy as dead before destroying
cx18: Move DVB buffer transfer handling from irq handler to work_queue thread.
In order to properly lock the epu2cpu mailbox for driver to CX23418 commands,
the DVB/TS buffer handling needs to be moved from the IRQ handler and IRQ
context to a work queue. This work_queue implmentation is strikingly similar
to the ivtv implementation - for better or worse.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- touch only one register for brightness change
- no quality control
- don't probe again at streamon time.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the H flip and the R & B color inversion of mode 320x240.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup.
The SCB field definitions for Ack IRQ's for mailboxes were inconsistent with
the bitmasks being loaded into those SCB fields and the SW2 Ack IRQ handling
logic. Renamed fields in SCB to make things consistent and did misc IRQ
handling cleanups: removing legacy ivtv dma_reg_lock, HPU IRQ flags, etc.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
