imx doesn't have any functions for setting the gamma table, so this is
completely defunct.
Not nice to lie to userspace, so let's stop!
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Just as the function ipu_dmfc_config_wait4eot() tells, the DMFC wait4eot bit
depends on the number of DMFC slots to be used, so it should be called after
the slots are determined in the function ipu_dmfc_alloc_bandwidth().
Based on tests, this patch may eliminate display distortion issue on overlay
plane with small resolutions. To reproduce the issue, we may run this drm
modetest case - 'modetest -P 19:64x64'.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The function name 'ipu_dmfc_config_wait4eot' matches the implementation of
the function better than 'ipu_dmfc_init_channel', since it only touches the
wait4eot bits.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since the function ipu_dmfc_init_channel() always returns zero, we may
change the return type to void to simplify the code.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The IMX dw_hdmi driver just called platform_set_drvdata() to get
your hopes up that maybe, somehow, you'd be able to retrieve the 'struct
imx_hdmi' from a pointer to the 'struct device'. You can't. When
we call dw_hdmi_bind() the main driver calls dev_set_drvdata(), which
clobbers our setting.
Let's just remove the platform_set_drvdata() to avoid dashing people's
hopes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The drm_encoder_cleanup() was missing both from the error path of
dw_hdmi_imx_bind(). This caused a crash when slub_debug was
enabled and we ended up deferring probe of HDMI at boot.
This call isn't needed from unbind() because if dw_hdmi_bind() returns
no error then it takes over the job of freeing the encoder (in
dw_hdmi_unbind).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The driver already advertises multi-planar YUV support, but
previously the U/V offset and stride setup was missing.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The IPU addresses multiplanar formats using a base address and relative
offsets for the secondary planes. Since those offsets must be positive
and not too large, and none of the plane parameters except the base address
may be changed while scanout is active, store the pitches and u/v offsets
and check all values against IDMAC limitations.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
- Add and make use of drm_of_active_endpoint helpers
- Silence a noisy dev_info into a dev_dbg
- Stop touching primary fb on pageflips
- Track flip state explicitly
- Keep GEM buffer objects referenced while scanout is active
- Implement fence sync by deferring flips to a workqueue for
dma-bufs with pending fences
- Actually disable vblank IRQs while they are not needed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ufbY
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-20160301' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm vblank IRQ control, fence support, and of endpoint helpers
- Add and make use of drm_of_active_endpoint helpers
- Silence a noisy dev_info into a dev_dbg
- Stop touching primary fb on pageflips
- Track flip state explicitly
- Keep GEM buffer objects referenced while scanout is active
- Implement fence sync by deferring flips to a workqueue for
dma-bufs with pending fences
- Actually disable vblank IRQs while they are not needed
* tag 'imx-drm-next-20160301' of git://git.pengutronix.de/git/pza/linux:
drm/imx: only enable vblank IRQs when needed
drm/imx: implement fence sync
drm/imx: keep GEM object referenced as long as scanout is active
drm/imx: track flip state explicitly
drm/imx: don't touch primary fb on pageflip
drm/imx: ipuv3 plane: Replace dev_info with dev_dbg if a plane's CRTC changes
gpu: ipu-v3: ipu-dc: Simplify display controller microcode setup
drm/rockchip: remove rockchip_drm_encoder_get_mux_id
drm/imx: remove imx_drm_encoder_get_mux_id
drm: add drm_of_encoder_active_endpoint helpers
The vblank IRQ is only needed to trigger page flip work, so we
might as well disable it when there is no work to do.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If the FB is backed by a GEM object with an dma-buf attached
we need to wait for any pending fences to signal before executing
the page flip.
The implementation is straight forward by deferring the flip to
a workqueue in that case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The DRM core only references the currently queued/active framebuffer.
So there is a period of time where the flip is not completed, but
the GEM object backing the FB is already unreferenced and could be
destroyed if userspace closes its handle.
Make sure to keep a reference to the GEM object until the flip is
actually executed clean things up in a worker running behind the
flip execution.
Also move the page flip event into the context of this worker, so
it gets cleaned up automatically.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Start tracking the flip state explicitly, as opposed to inferring
it from the presence if a new FB. This is a preparatory step to
introduce an new immediate state, where we can wait for a fence to
signal.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The core already does the correct replacemet if the driver
page flip function returns without an error, so there is no
need to do it here.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch changes the dev_info() call to dev_dbg() in ipu_plane_update()
to print out the information that a plane's CRTC is changed, because this
kind of information is only useful for debugging.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
It is replaced by drm_of_encoder_active_port_id.
Suggested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
DRM_FORMAT_RGB565 is missing from ipu_plane_formats.
The support is there, just need to make it available to userspace.
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Make sure the DRM core is aware that there will be no vblank interrupts
incoming if the CRTC is disabled. That way the core will reject any
attempts from userspace to wait on a vblank event on a disabled CRTC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
So this one is special, since it tries to prevent races when userspace
crashes simply by disabling the vblank machinery. Well except that imx
always has vblanks enabled, and the disable_vblank hook actually just
tries to cancel a pending pageflip. Without any locking whatsoever. Of
course this is wrong, since it'll result in the hw not actually
displaying what drm thinks is the current frontbuffer.
Well since the core takes care of the disappearing DRM fd now. So we
can nuke all this confused code without ill side-effects.
Someone else needs to audit the locking for ->newfb and
->page_flip_event and fix it up. Common approach is to reuse
dev->event_lock for this.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-7-git-send-email-daniel.vetter@ffwll.ch
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The drm_fbdev_cma_init function always calls the
drm_helper_disable_unused_functions. Since it's part of the usual probe
process, all the drivers using that helper will end up having their encoder
and CRTC disable functions called at probe if their device has not been
reported as enabled.
This could be fixed by reading out from the registers the current state of
the device if it is enabled, but even that will not handle the case where
the device is actually disabled.
Moreover, the drivers using the atomic modesetting expect that their enable
and disable callback to be called when the device is already enabled or
disabled (respectively).
We can however fix this issue by moving the call to
drm_helper_disable_unused_functions out of drm_fbdev_cma_init and make the
drivers needing it (all the drivers calling drm_fbdev_cma_init and not
using the atomic modesetting) explicitly call it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452785109-6172-14-git-send-email-maxime.ripard@free-electrons.com
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An encoder is associated with a connector by the DRM core as a result of
setting up a configuration. Drivers using the atomic or legacy helpers
should never set up this link, even if it is a static one.
While at it, try to catch this kind of error in the future by adding a
WARN_ON() in drm_mode_connector_attach_encoder(). Note that this doesn't
cover all the cases, since drivers could set this up after attaching.
Drivers that use the atomic helpers will get a warning later on, though,
so hopefully the two combined cover enough to help people avoid this in
the future.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Mark yao <mark.yao@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447694393-24700-1-git-send-email-thierry.reding@gmail.com
Use the drm_crtc_index() helper to determine the pipe number of the CRTC
instead.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-5-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no reason whatsoever why this should ever be negative. The same
goes for the number of pipes added to the DRM device.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450178476-26284-4-git-send-email-boris.brezillon@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!! enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.
Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.
I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NUL for no-name instead of ""
Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWZMgaAAoJEHm+PkMAQRiGGcIH+gNS/hbN2DKW7wphl1QuaV7C
1fror8AvpwbGa/o0yuxovaVuZzAR0TF31vn+gAemF4U/hnM25xqxEHXYZEVv8OWw
mbz4/z+jbVk3SiS5AiZPIZgL4W6RZnG5QYfiTVGPlBHuBznW2ITlNlClBOmBL45o
uhb3bjTzi70AZ7Gh6i9sHgJoHg6D9u/ZxLaLcWnM79BzyTMHTf2t0wnrQmh66lEE
hp7Rn9wXv9bk/e3iH7CVUb97P4IWhhkmfqcoturqAg9+C/M26b0VmvQp9Sy8S6Pd
FVQ+SUIZllj5ZDKe9mOcs37czlxTr0keEFqzWeMh/7y4iuI3RaRp/qb+7mX5sIE=
=WGZ1
-----END PGP SIGNATURE-----
Back merge tag 'v4.4-rc4' into drm-next
We've picked up a few conflicts and it would be nice
to resolve them before we move onwards.
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ipu_crtc_handle_pageflip() was calling drm_send_vblank_event() with
a pipe argument of -1. Commit cc1ef118fc ("drm/irq: Make pipe
unsigned and name consistent") now makes this error obvious, as we
now may get a warning from:
if (WARN_ON(pipe >= dev->num_crtcs))
in drm_vblank_count_and_time(). Prior to this change, we would end
up making out-of-bounds array accesses via:
struct drm_vblank_crtc *vblank = &dev->vblank[crtc];
and
*vblanktime = vblanktimestamp(dev, pipe, cur_vblank);
So, this has been broken for a very long time, and is not a result
of the above commit. Since we don't care about the staging versions,
I've tagged this with the earliest mainline commit where we do care,
even though this commit did not introduce the bug.
Fixes: 6556f7f82b ("drm: imx: Move imx-drm driver out of staging")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
DRM_IMX_FB_HELPER config is currently used to enable/disable fbdev
emulation for the imx kms driver.
Remove this local config option and use the top level DRM_FBDEV_EMULATION
config option where applicable. Using this config lets us also prevent
wrapping around drm_fb_helper_* calls with #ifdefs in certain places.
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1445933459-5249-2-git-send-email-architt@codeaurora.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The drm_fbdev_cma_restore_mode() function tests whether its argument
is NULL and then returns immediately.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The crtc child device driver shouldn't modify the of_node of its platform
device in the probe function. Instead, since the previous patch, the IPU
core driver sets the of_node when the platform device is created.
Drop the now unused custom imx_drm_get_port_by_id function.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Similarly to commit 5e501ed725 ("drm/imx: imx-ldb: allow to determine
bus format from the connected panel"), if a panel is connected to the ldb
output port via the of_graph bindings, the data mapping is determined from
the display_info.bus_format field provided by the panel instead of from the
optional interface_pix_fmt device tree property.
Reported-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
For primary plane initialization failure cases, ipu_plane_init() may return
a pointer encoded by ERR_PTR(). So, we should bailout instead of using that
pointer blindly.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use drm_universal_plane_init to create the planes, create the primary
plane first and use drm_crtc_init_with_planes to associate it with
the crtc.
This gets rid of the unused fallback primary plane previously created
by drm_crtc_init and fixes a NULL pointer dereference issue that can
be triggered by a modeset from userspace when fbdev helpers are
enabled [1].
[1] https://lkml.org/lkml/2015/11/4/107
Reported-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Liu Ying <Ying.Liu@freescale.com>
- Some correctness fixes found by coccinelle
- Add drivers/gpu/ipu-v3 directory to MAINTAINERS
- Add support for more color formats
- Fix a regression, making displays larger than FullHD work again
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EqNE
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2015-10-30' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm fixes and color format updates
- Some correctness fixes found by coccinelle
- Add drivers/gpu/ipu-v3 directory to MAINTAINERS
- Add support for more color formats
- Fix a regression, making displays larger than FullHD work again
* tag 'imx-drm-next-2015-10-30' of git://git.pengutronix.de/git/pza/linux:
drm/imx: hdmi: fix HDMI setup to allow modes larger than FullHD
gpu: ipu-v3: fix div_ratio type
gpu: ipu-v3: csi: add support for 8 bpp grayscale sensors.
drm/imx: enable ARGB4444 16-bit color format
gpu: ipu-v3: add support for ARGB4444 16-bit color format
drm/imx: ipuv3-plane: enable support for RGBX8888 and RGBA8888 pixel formats
gpu: ipu-v3: add support for RGBX8888 and RGBA8888 pixel formats
drm/imx: enable 15-bit RGB with 1-bit alpha formats
gpu: ipu-v3: add support for 15-bit RGB with 1-bit alpha formats
MAINTAINERS: Add IPUv3 core driver to the i.MX DRM driver section
gpu: ipu-v3: ipu-csi: bool test doesn't need a comparison to false
This worked before the dw-hdmi bridge code was changed to validate
the setup data more strictly. Add back support for modes with a
pixel clock up to 216MHz. Even higher clocks should work, but we
are missing the required setup data for now.
Also change the mode validate callbacks to disallow modes with
higher pixelclocks, so we don't end up failing the modeset later
on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch allows to use the ARGB4444 color format on planes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The generic function is functionally equivalent to the driver's
imx_drm_platform_probe(). Use the generic function and reduce the
overall code size.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1445332995-11212-3-git-send-email-Liviu.Dudau@arm.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a7c6e76fee ("drm/imx: switch to use media bus formats") accidentally
replaced IPU_PIX_FMT_GBR24 with MEDIA_BUS_FMT_YUV8_1X24 instead of the correct
MEDIA_BUS_FMT_GBR888_1X24. This patch is needed to fix VGA output in i.MX53.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The parallel-display driver used an undocumented, non-standard property
"fsl,panel" to optionally associate with a drm_panel device. This patch
fixes the driver to use the same OF graph bindings as the LDB driver
instead:
parallel-display {
compatible = "fsl,imx-parallel-display";
...
port@1 {
reg = <1>;
parallel_out: endpoint {
remote_endpoint = <&panel_in>;
};
};
};
panel {
...
port {
panel_in: endpoint {
remote-endpoint = <¶llel_out>;
};
};
};
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
This set of patches adjust the setup of the HDMI CTS/N values for audio
support to be compliant with the work-around given in the iMX6 errata
documentation as part of the preparation for integrating audio support
for this driver, and also update the HDMI phy configuration for Rockchip
devices to improve the HDMI eye pattern.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: rockchip/dw_hdmi-rockchip: improve for HDMI electrical test
drm: bridge/dw_hdmi: separate VLEVCTRL settting into platform driver
drm: bridge/dw_hdmi: fixed codec style
drm: bridge/dw_hdmi: adjust n/cts setting order
drm: bridge/dw_hdmi: protect n/cts setting with a mutex
drm: bridge/dw_hdmi: combine hdmi_set_clock_regenerator_n() and hdmi_regenerate_cts()
Conflicts:
drivers/gpu/drm/imx/dw_hdmi-imx.c
- Add media bus formats needed by imx-drm
- Switch to use media bus formats to describe the pixel format
on the internal parallel bus between display interface and
encoders
- Some preparations for TV Output via TVEv2 on i.MX5
- Add drm_panel support to the i.MX LVDS driver, allow to
determine the bus pixel format from the panel descriptor.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nTVr
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2015-03-31' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm changes to use media bus formats and LDB drm_panel support
- Add media bus formats needed by imx-drm
- Switch to use media bus formats to describe the pixel format
on the internal parallel bus between display interface and
encoders
- Some preparations for TV Output via TVEv2 on i.MX5
- Add drm_panel support to the i.MX LVDS driver, allow to
determine the bus pixel format from the panel descriptor.
* tag 'imx-drm-next-2015-03-31' of git://git.pengutronix.de/git/pza/linux:
drm/imx: imx-ldb: allow to determine bus format from the connected panel
drm/imx: imx-ldb: reset display clock input when disabling LVDS
drm/imx: imx-ldb: add drm_panel support
drm/imx: consolidate bus format variable names
drm/imx: switch to use media bus formats
Add RGB666_1X24_CPADHI media bus format
Add YUV8_1X24 media bus format
Add BGR888_1X24 and GBR888_1X24 media bus formats
Add LVDS RGB media bus formats
Add RGB444_1X12 and RGB565_1X16 media bus formats
drm/imx: ipuv3-crtc: Allow to divide DI clock from TVEv2
drm/imx: Add support for interlaced scanout
Using the for_each_... macro should make the code bit shorter and
easier to read. This patch also properly decrements the endpoint node
reference count before returning out of the loop.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Because of iMX6 & Rockchip have differnet mpll config parameter,
the VLEVCTRL parameter would be different. In this case we should
separate VLEVCTRL setting from the common dw_hdmi driver, config
this parameter in platform driver(dw_hdmi-imx and dw_hdmi-rockchip)
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes the fsl,data-width and fsl,data-mapping device tree
properties optional if a panel is connected to the ldb output port
via the of_graph bindings. The data mapping is determined from the
display_info.bus_format field provided by the panel.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The LDB driver changes the attached display interface's input clock mux
to the LDB_DI clock reference. Change it back again when disabling the
LVDS display. Changing back to the PLL5 for example allows to configure
the same DI for HDMI output later.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch allows to optionally attach the lvds-channel to a panel
supported by a drm_panel driver using of-graph bindings, instead of
supplying the modes via display-timings in the device tree.
This depends on of_graph_get_port_by_id and uses the OF graph to
link the optional DRM panel to the LDB lvds-channel. The output
port number is 1 on devices without the 4-port input multiplexer
(i.MX5) and 4 on devices with the mux (i.MX6).
Before:
ldb {
...
lvds-channel@0 {
...
display-timings {
native-timing = <&timing1>;
timing1: etm0700g0dh6 {
hactive = <800>;
vactive = <480>;
clock-frequency = <33260000>;
hsync-len = <128>;
hback-porch = <88>;
hfront-porch = <40>;
vsync-len = <2>;
vback-porch = <33>;
vfront-porch = <10>;
hsync-active = <0>;
vsync-active = <0>;
...
};
};
...
};
};
After:
ldb {
...
lvds-channel@0 {
...
port@4 {
reg = <4>;
lvds_out: endpoint {
remote_endpoint = <&panel_in>;
};
};
};
};
panel {
compatible = "edt,etm0700g0dh6", "simple-panel";
...
port {
panel_in: endpoint {
remote-endpoint = <&lvds_out>;
};
};
};
[Fixed build error due to missing select on DRM_PANEL --rmk]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch consolidates the different interface_pix_fmt, pixel_fmt, pix_fmt,
and pixfmt variables to a common name "bus_format" wherever they describe the
pixel format on the bus between display controller and encoder hardware.
At the same time, it renames imx_drm_panel_format to imx_drm_set_bus_format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
imx-drm internally misused the V4L2_PIX_FMT constants, which are supposed to
describe the pixel format of frame buffers in memory, to describe the pixel
format on the bus between the display controller and the encoder hardware.
Now that MEDIA_BUS_FMT constants are available to drm drivers, use those
instead.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
This patch allows the IPU to divide the 27 MHz input clock from
the TVE by two to obtain the 13.5 MHz pixel clock needed for
NTSC/PAL SD modes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This series converts of_graph_get_next_endpoint to decrement the refcount of
the passed prev parameter. This allows to add a for_each_endpoint_of_node
helper macro to loop over all endpoints in a device tree node.
The of_graph_get_port_by_id function is added to retrieve a port by its known
port id (contained in the reg property) from the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jtB3
-----END PGP SIGNATURE-----
Merge tag 'of-graph-for-4.0' of git://git.pengutronix.de/git/pza/linux into for-next
Pull of-graph helpers from Philipp Zabel:
of: Add of-graph helpers to loop over endpoints and find ports by id
This series converts of_graph_get_next_endpoint to decrement the refcount of
the passed prev parameter. This allows to add a for_each_endpoint_of_node
helper macro to loop over all endpoints in a device tree node.
The of_graph_get_port_by_id function is added to retrieve a port by its known
port id (contained in the reg property) from the device tree.
Commit eb10d63555 ("imx-drm: encoder prepare/mode_set must use adjusted mode")
broke the first LVDS modeset by using crtc->hwmode before crtc mode_set is
called. In fact, encoder prepare is not supposed to prepare the display clock
at all. Rather encoder mode_set should be used to set the DI clock rate, before
it is enabled by crtc commit.
Reported-by: Liu Ying <Ying.Liu@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The loop iterating over curr_ctrl in dw_hdmi terminates on mpixelclock == ~0UL,
so there needs to be an end of list element here in case a mode with a pixel
clock larger than 216 MHz is set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch limits the pixel clock to 13.4 MHz - 266 MHz for i.MX6Q
and 13.5 MHz - 270 MHz for i.MX6DL, which is the range documented
in the HDMI Transmitter chapter of the respective reference manuals.
Without this patch, when connected to a monitor capable of 2160p60
modes, dw_hdmi will happily report this mode and the IPU code will
cause a division by zero in ipu_di_config_clock when trying to figure
out how to divide the 264 MHz HSP clock down to ~600 MHz.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Decrementing the reference count of the previous endpoint node allows to
use the of_graph_get_next_endpoint function in a for_each_... style macro.
All current users of this function that pass a non-NULL prev parameter
(that is, soc_camera and imx-drm) are changed to not decrement the passed
prev argument's refcount themselves.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
- Corrected handling of wait_for_completion_timeout return value
when disabling IPUv3 DC channels
- Fixed error return value propagation in TVE mode_set
- Fixed IPUv3 register offsets for IC module on i.MX51 and i.MX53
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tRBf
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-fixes-2015-01-28' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm fixes for IPUv3 DC and i.MX5 IPUv3 IC and TVE
- Corrected handling of wait_for_completion_timeout return value
when disabling IPUv3 DC channels
- Fixed error return value propagation in TVE mode_set
- Fixed IPUv3 register offsets for IC module on i.MX51 and i.MX53
* tag 'imx-drm-fixes-2015-01-28' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: Fix IC control register offset
drm: imx: imx-tve: Check and propagate the errors
gpu: ipu-v3: wait_for_completion_timeout does not return negative status
DRM_GEM_CMA_HELPER is depend on HAVE_DMA_ATTRS, or it will break the
building. The related error (with allmodconfig under xtensa):
CC [M] drivers/gpu/drm/drm_gem_cma_helper.o
drivers/gpu/drm/drm_gem_cma_helper.c: In function 'drm_gem_cma_create':
drivers/gpu/drm/drm_gem_cma_helper.c:110:19: error: implicit declaration of function 'dma_alloc_writecombine' [-Werror=implicit-function-declaration]
cma_obj->vaddr = dma_alloc_writecombine(drm->dev, size,
^
drivers/gpu/drm/drm_gem_cma_helper.c:110:17: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
cma_obj->vaddr = dma_alloc_writecombine(drm->dev, size,
^
drivers/gpu/drm/drm_gem_cma_helper.c: In function 'drm_gem_cma_free_object':
drivers/gpu/drm/drm_gem_cma_helper.c:193:3: error: implicit declaration of function 'dma_free_writecombine' [-Werror=implicit-function-declaration]
dma_free_writecombine(gem_obj->dev->dev, cma_obj->base.size,
^
drivers/gpu/drm/drm_gem_cma_helper.c: In function 'drm_gem_cma_mmap_obj':
drivers/gpu/drm/drm_gem_cma_helper.c:330:8: error: implicit declaration of function 'dma_mmap_writecombine' [-Werror=implicit-function-declaration]
ret = dma_mmap_writecombine(cma_obj->base.dev->dev, vma,
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the case of errors we should propagate them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
We do not need to track the state of the IPU DI's clock flags by having
each display bridge calling back into imx-drm-core, and then back out
into ipuv3-crtc.c.
ipuv3-crtc can instead just scan the list of encoders to retrieve their
type, and build up a picture of which types of encoders are attached.
We can then use this information to configure the IPU DI clocking mode
without any uncertainty - if we have multiple bridges connected to the
same DI, if one of them requires a synchronous DI clock, that's what we
must use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch changes struct ipu_di_signal_cfg to use struct videomode
to define video timings and flags.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The encoder ->prepare() and ->mode_set() methods need to use the
hw adjusted mode, not the original mode.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Ask the IPU display interface, via ipu_di_adjust_videomode(), to
adjust a video mode to meet any DI restrictions. The function takes
a subsystem independent videomode, so the drm_display_mode must be
converted to videomode first, and then the adjusted mode converted
back to a drm_display_mode.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
the original imx hdmi driver is under drm/imx/,
which depends on imx-drm, so move the imx hdmi
driver out to drm/bridge and rename it to dw_hdmi
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
hdmi phy configuration is platform specific, which can be adjusted
according to the board to get the best SI
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
IMX6 and Rockchip RK3288 and JZ4780 (Ingenic Xburst/MIPS)
use the interface compatible Designware HDMI IP, but they
also have some lightly differences, such as phy pll configuration,
register width, 4K support, clk useage, and the crtc mux configuration
is also platform specific.
To reuse the imx hdmi driver, convert it to drm_bridge
handle encoder in imx-hdmi_pltfm.c, as most of the encoder
operation are platform specific such as crtc select and
panel format set
This patch depends on Russell King's patch:
drm: imx: convert imx-drm to use the generic DRM OF helper
http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2014-July/053484.html
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
drm driver may probe before the i2c bus, so the driver should
defer probing until it is available
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
CHECK: Alignment should match open parenthesis
+ if ((hdmi->vic == 10) || (hdmi->vic == 11) ||
+ (hdmi->vic == 12) || (hdmi->vic == 13) ||
CHECK: braces {} should be used on all arms of this statement
+ if (hdmi->hdmi_data.video_mode.mdvi)
[...]
+ else {
[...]
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use the generic DRM OF helper to locate the possible CRTCs for the
encoder, thereby shrinking the imx-drm driver some more.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If edid was allocated during bind, it must be freed again during unbind.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If edid was allocated during bind, it must be freed again during unbind.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good thing,
but not at a huge rate this release, only about 70k lines removed
overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid details.
The "contentious" thing here is the movement of the Android binder code
out of staging into the "real" part of the kernel. This is code that
has been stable for a few years now and is working as-is in the tens of
millions of devices with no issues. Yes, the code is horrid, and the
userspace api leaves a lot to be desired, but it's not going to change
due to legacy issues that we have no control over. Because so many
devices and companies rely on this, and the code is stable, might as
well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been doing
it for the past few years with no problems. I'll send a MAINTAINERS
entry for it before 3.19-final is out, still need to talk to the Google
developers about if they are willing to help with it or not, last I
checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSPICkACgkQMUfUDdst+yksdwCfSLE9VUy1o2sAPDRe+J3bQced
EWEAoL3RtnejKbo5tHS2IT69pLrwiIDS
=YXyM
-----END PGP SIGNATURE-----
Merge tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good
thing, but not at a huge rate this release, only about 70k lines
removed overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid
details.
The "contentious" thing here is the movement of the Android binder
code out of staging into the "real" part of the kernel. This is code
that has been stable for a few years now and is working as-is in the
tens of millions of devices with no issues. Yes, the code is horrid,
and the userspace api leaves a lot to be desired, but it's not going
to change due to legacy issues that we have no control over. Because
so many devices and companies rely on this, and the code is stable,
might as well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been
doing it for the past few years with no problems. I'll send a
MAINTAINERS entry for it before 3.19-final is out, still need to talk
to the Google developers about if they are willing to help with it or
not, last I checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits)
Staging: slicoss: Fix long line issues in slicoss.c
staging: rtl8712: remove unnecessary else after return
staging: comedi: change some printk calls to pr_err
staging: rtl8723au: hal: Removed the extra semicolon
lustre: Deletion of unnecessary checks before three function calls
staging: lustre: fix sparse warnings: static function declaration
staging: lustre: fixed sparse warnings related to static declarations
staging: unisys: remove duplicate header
staging: unisys: remove unneeded structure
staging: ft1000 : replace __attribute ((__packed__) with __packed
drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c"
Drivers:staging:rtl8192e: Fixed checkpatch warning
Drivers:staging:clocking-wizard: Added a newline
staging: clocking-wizard: check for a valid clk_name pointer
staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts
staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily
staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1()
staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation
staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB()
staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation
...
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
The imx-drm driver was put into staging mostly for the following reasons,
all of which have been addressed or superseded:
- convert the irq driver to use linear irq domains
- work out the device tree bindings, this lead to the common of_graph
bindings being used
- factor out common helper functions, this mostly resulted in the
component framework and drm of_graph helpers.
Before adding new fixes, and certainly before adding new features,
move it into its proper place below drivers/gpu/drm.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
