Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.
This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.
This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.
However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.
Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.
This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.
Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.
Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().
This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.
To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.
In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to i40e and i40evf only.
Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.
Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.
Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts. This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.
Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.
Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.
Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed. Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.
Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.
Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a simple statistic to count the ipsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info. Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On a chip reset most of the table contents are lost, so must be
restored. This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware. We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.
The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle. However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set up the data structures to be used by the ipsec offload.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add in the code for running and stopping the hardware ipsec
encryption/decryption engine. It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization. Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2502:12: error: 'fm10k_suspend' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2475:12: error: 'fm10k_resume' defined but not used [-Werror=unused-function]
It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.
Fixes: 8249c47c6b ("fm10k: use generic PM hooks instead of legacy PCIe power hooks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value. This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value. This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This update makes it so that we report the actual number of Tx queues via
real_num_tx_queues but are still restricted to RSS on only the first pool
by setting num_tc equal to 1. Doing this locks us into only having the
ability to setup XPS on the queues in that pool, and only those queues
should be used for transmitting anything other than macvlan traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that instead of bringing rings up/down for various
we just update the netdev pointer for the Rx ring and set or clear the MAC
filter for the interface. By doing it this way we can avoid a number of
races and issues in the code as things were getting messy with the macvlan
clean-up racing with the interface clean-up to bring the rings down on
shutdown.
With this change we opt to leave the rings owned by the PF interface for
both Tx and Rx and just direct the packets once they are received to the
macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not be stopping/starting the upper devices Tx queues when
handling a macvlan offload. Instead we should be stopping and starting
traffic on our own queues.
In order to prevent us from doing this I am updating the code so that we no
longer change the queue configuration on the upper device, nor do we update
the queue_index on our own device. Instead we can just use the queue index
for our local device and not update the netdev in the case of the transmit
rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't be recording the Rx queue on macvlan offloaded frames since
the macvlan is normally brought up as a single queue device, and it will
trigger warnings for RPS if we have recorded queue IDs larger than the
"real_num_rx_queues" value recorded for the device.
Instead we should be recording the macvlan statistics since we are
bypassing the normal macvlan statistics that would have been generated by
the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code throughout ixgbe was assuming that dev->num_tc was populated and
configured with the driver, when in fact this can be configured via mqprio
without any hardware coordination other than restricting us to the real
number of Tx queues we advertise.
Instead of handling things this way we need to keep a local copy of the
number of TCs in use so that we don't accidentally pull in the TC
configuration from mqprio when it is configured in software mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We might as well configure the limit to default to 1 pool always for the
interface. This accounts for the fact that the PF counts as 1 pool if
SR-IOV is enabled, and in general we are always running in 1 pool mode when
RSS or DCB is enabled as well, though we don't need to actually evaluate
any of the VMDq features in those cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The macvlan driver itself will validate the MAC address that is configured
for a given interface. There is no need for us to verify it again.
Instead we should be checking to verify that we actually allocate the filter
and have not run out of resources to configure a MAC rule in our filter
table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
track_id == 0 is valid for “read only” profiles when
profile does not have any “write” commands.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
PPP name was going to be confusing since PPP already means point
to point protocol. It is decided to change pipeline personalization
profile(ppp) to dynamic device personalization(ddp).
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Having the interrupts firing while we are polling causes extra overhead and
isn't needed for most systems out there. If an interrupt is lost us
experiencing a 2s latency spike before recovering is still not acceptable
and masks the issue. We are better off just identifying systems that lose
interrupts and instead enable workarounds for those systems.
To that end I am dropping the code that was strobing the interrupts as
there is a narrow window where having them enabled can actually cause
race issues anyway where a few stray packets might get misses if the
interrupt is re-enabled and fires before we call napi_complete.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If you enabled and disabled promiscuous mode on a VF you could easily put
it into a state where it would start firing interrupts on all queues at a
rate of 50+ interrupts per second even though there was no traffic present.
The issue seems to have been a stray admin queue feature flag set that was
leaving us in a high polling rate for the adminq task.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not be clearing the pending bit array for each vector manually.
The documentation for the hardware states that when in MSI-X mode the
pending bit array will be cleared automatically. Us clearing it ourselves
just results in multiple opportunities for us to drop an interrupt.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Variable read_size is initialized and this value is never read, it is
instead set inside the do-loop, hence the initialization is redundant
and can be removed. Cleans up clang warning:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:390:6: warning: Value stored
to 'read_size' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the i40e driver from 2.1.14 to 2.3.2.
Bump the i40evf driver from 3.0.1 to 3.2.2
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We introduced the virtchnl interface in order to have an interface for
talking to a virtual device driver which was host-driver agnostic. This
interface has its own definitions, including one for link speed.
The host driver has to talk to the virtchnl interface using these new
definitions in order to remain compatible. Today, the i40e link_speed
enumerations are value-exact matches for the virtchnl interface, so it
was originally decided to simply use a typecast.
However, this is unsafe, and makes it easier for future drivers to
continue this unsafe practice. There is nothing guaranteeing these
values are exact, and the type-cast would hide any compiler warning
which indicates the problem.
Rather than rely on this type cast, introduce a helper function which
can convert the AdminQ link speed definition into a virtchnl
definition. This can then be used by host driver implementations in
order to safely convert to the interface recognized by the virtual
functions.
If the link speed is not able to be represented by the virtchnl
definitions we'll report UNKNOWN which is the safest result.
This will ensure that should the driver specific link_speeds actual bit
definitions change, we do not report them incorrectly according to the
VF.
Additionally, this provides a better pattern for future drivers to copy,
as it is more likely a future device may not use the exact same bit-wise
definition as the current virtchnl interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We currently notify a VF of the link state after ENABLE_QUEUES, which is
the last thing a VF does after being configured. Guests may not actually
ENABLE_QUEUES until they get configured, and thus between driver load
and device configuration the VF may show inaccurate link status.
Fix this by also sending the link state after GET_VF_RESOURCES. Although
we could remove the message following ENABLE_QUEUES, it's not that
significant of a loss, so this patch just keeps both to ensure maximum
compatibility with guests on various OSes.
Specifically, without this patch guests running FreeBSD will display
inaccurate link state until the device is brought up. This is mostly
a cosmetic issue but can be confusing to system administrators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If i40evf_open() is called quickly at the same time as a reset occurs
(such as via ethtool) it is possible for the device to attempt to open
while a reset is in progress. This occurs because the driver was not
holding the critical task bit lock during i40evf_open, nor was it
holding it around the call to i40evf_up_complete() in
i40evf_reset_task().
We didn't hold the lock previously because calls to i40evf_down() would
take the bit lock directly, and this would have caused a deadlock.
To avoid this, we'll move the bit lock handling out of i40evf_down() and
into the callers of this function. Additionally, we'll now hold the bit
lock over the entire set of steps when going up or down, to ensure that
we remain consistent.
Ultimately this causes us to serialize the transitions between down and
up properly, and avoid changing status while we're resetting.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although not strictly necessary, it is customary to reverse the order in
which we release locks that we acquire. This helps preserve lock
ordering during future refactors, which can help avoid potential
deadlock situations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
