The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.
Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).
In this check it only looks if the triplet [link, speed, duplex] is
being changed.
This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.
In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.
In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_smi_direct_wait routine is used to wait on indirect
registers access. It is of no exception and must delay between read
attempts, like other wait routines.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx_smi_direct_wait function is only used to check
the 16th bit of the (16-bit) SMI Command register. But the bit shift
operation is not enough if we eventually use this function to check
other bits, thus replace it with a mask.
Fixes: e7ba0fad9c ("net: dsa: mv88e6xxx: refine SMI support")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have proper Wait Bit and Wait Mask routines, remove the
unused mv88e6xxx_wait routine and its Global 1 and Global 2 variants.
The indirect tables such as the Device Mapping Table or Priority
Override Table make use of an Update bit to distinguish reading (0)
from writing (1) operations. After a write operation occurs, the bit
self clears right away so there's no need to wait on it. Thus keep
things simple and remove the mv88e6xxx_update helper as well.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVB is not an indirect table using an Update bit, but a unit using
a Busy bit. This means that we must ensure that this bit is cleared
before setting it and wait until it gets cleared again after writing
an operation. Reflect that.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many portions of the driver need to wait until a given bit is set
or cleared. Some busses even have a specific implementation for this
operation. In preparation for such variant, implement a generic Wait
Bit routine that can be used by the driver core functions.
This allows us to get rid of the custom implementations we may find
in the driver. Note that for the EEPROM bits, BUSY and RUNNING bits
are independent, thus it is more efficient to wait independently for
each bit instead of waiting for their mask.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx_wait routine is used to wait for a given mask
to be cleared to zero. However in some cases, the driver may have
to wait for a given mask to be of a certain non-zero value.
Thus provide a generic wait mask routine that will be used to implement
the current mv88e6xxx_wait function, and use it to wait for 88E6185
PPU states.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPU state of 88E6185 can be either "Disabled at Reset" or
"Disabled after Initialization". Because we intentionally clear the
PPU Enabled bit before checking its state, it is safe to wait for the
MV88E6185_G1_STS_PPU_STATE_DISABLED state explicitly instead of waiting
for any state different than MV88E6185_G1_STS_PPU_STATE_POLLING.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/sja1105/sja1105_main.c: In function sja1105_fdb_dump:
drivers/net/dsa/sja1105/sja1105_main.c:1226:14: warning:
variable tx_vid set but not used [-Wunused-but-set-variable]
drivers/net/dsa/sja1105/sja1105_main.c:1226:6: warning:
variable rx_vid set but not used [-Wunused-but-set-variable]
They are not used since commit 6d7c7d948a ("net: dsa:
sja1105: Fix broken learning with vlan_filtering disabled")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d35 ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kconfig option is unused, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the two headers into one, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ksz_port_cleanup(), which is unused. Add missing include
"ksz_common.h", which fixes the following warning when built with
make ... W=1
drivers/net/dsa/microchip/ksz_common.c:23:6: warning: no previous prototype for ‘...’ [-Wmissing-prototypes]
Note that the order of the headers cannot be swapped, as that would
trigger missing forward declaration errors, which would indicate the
way forward is to merge the two headers into one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to drop the adjust_link callback in order to finally migrate to
phylink.
Otherwise we get the following warning during startup:
"mv88e6xxx 2188000.ethernet-1:10: Using legacy PHYLIB callbacks. Please
migrate to PHYLINK!"
The warning is generated in the function dsa_port_link_register_of in
dsa/port.c:
int dsa_port_link_register_of(struct dsa_port *dp)
{
struct dsa_switch *ds = dp->ds;
if (!ds->ops->adjust_link)
return dsa_port_phylink_register(dp);
dev_warn(ds->dev,
"Using legacy PHYLIB callbacks. Please migrate to PHYLINK!\n");
[...]
}
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds PTP support for the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is done for all the other structs within this driver.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.
If a user configures an invalid port, an error is returned.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read and
_mv88e6xxx_port_vlan_add is the only function requiring the preparation
of a new VLAN entry.
To simplify things up, remove the mv88e6xxx_vtu_get wrapper and
explicit the VLAN lookup in _mv88e6xxx_port_vlan_add. This rework
also avoids programming the broadcast entries again when changing a
port's membership, e.g. from tagged to untagged.
At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read.
Explicit the call to mv88e6xxx_vtu_getnext in _mv88e6xxx_port_vlan_del
and the return value expected by switchdev in case of software VLANs.
At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_vtu_getnext is simple enough to call it directly in the
mv88e6xxx_port_db_load_purge function and explicit the return code
expected by switchdev for software VLANs when an hardware VLAN does
not exist.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_vtu_getnext interprets two members from the input
mv88e6xxx_vtu_entry structure: the (excluded) vid member to start
the iteration from, and the valid argument specifying whether the VID
must be written or not (only required once at the start of a loop).
Explicit the assignation of these two fields right before calling
mv88e6xxx_vtu_getnext, as it is done in the mv88e6xxx_vtu_get wrapper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lock the mutex in the mv88e6xxx_port_vlan_prepare function
called by the DSA stack, instead of doing it in the internal
mv88e6xxx_port_check_hw_vlan helper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Microchip KSZ8795 DSA driver.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set phy device advertising to enable MAC flow control.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the define here makes the code more expressive.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have an ERPS (Ethernet Ring Protection Switching) setup involving
mv88e6250 switches which we're in the process of switching to a BSP
based on the mainline driver. Breaking any link in the ring works as
expected, with the ring reconfiguring itself quickly and traffic
continuing with almost no noticable drops. However, when plugging back
the cable, we see 5+ second stalls.
This has been tracked down to the userspace application in charge of
the protocol missing a few CCM messages on the good link (the one that
was not unplugged), causing it to broadcast a "signal fail". That
message eventually reaches its link partner, which responds by
blocking the port. Meanwhile, the first node has continued to block
the port with the just plugged-in cable, breaking the network. And the
reason for those missing CCM messages has in turn been tracked down to
the VTU apparently being too busy servicing load/purge operations that
the normal lookups are delayed.
Initial state, the link between C and D is blocked in software.
_____________________
/ \
| |
A ----- B ----- C *---- D
Unplug the cable between C and D.
_____________________
/ \
| |
A ----- B ----- C * * D
Reestablish the link between C and D.
_____________________
/ \
| |
A ----- B ----- C *---- D
Somehow, enough VTU/ATU operations happen inside C that prevents
the application from receving the CCM messages from B in a timely
manner, so a Signal Fail message is sent by C. When B receives
that, it responds by blocking its port.
_____________________
/ \
| |
A ----- B *---* C *---- D
Very shortly after this, the signal fail condition clears on the
BC link (some CCM messages finally make it through), so C
unblocks the port. However, a guard timer inside B prevents it
from removing the blocking before 5 seconds have elapsed.
It is not unlikely that our userspace ERPS implementation could be
smarter and/or is simply buggy. However, this patch fixes the symptoms
we see, and is a small optimization that should not break anything
(knock wood). The idea is simply to avoid doing an VTU load of an
entry identical to the one already present. To do that, we need to
know whether mv88e6xxx_vtu_get() actually found an existing entry, or
has just prepared a struct mv88e6xxx_vtu_entry for us to load. To that
end, let vlan->valid be an output parameter. The other two callers of
mv88e6xxx_vtu_get() are not affected by this patch since they pass
new=false.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the legacy bulk gpio.h include
with the proper gpio/consumer.h variant. This was
caught by the kbuild test robot that was running
into an error because of this.
For more information why linux/gpio.h is bad can be found in:
commit 56a46b6144 ("gpio: Clarify that <linux/gpio.h> is legacy")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://www.spinics.net/lists/netdev/msg584447.html
Fixes: a653f2f538 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The restructuring of the driver got the dependencies wrong: without
CONFIG_NET_DSA we get this build failure:
WARNING: unmet direct dependencies detected for NET_DSA_VITESSE_VSC73XX
Depends on [n]: NETDEVICES [=y] && HAVE_NET_DSA [=y] && OF [=y] && NET_DSA [=n]
Selected by [m]:
- NET_DSA_VITESSE_VSC73XX_PLATFORM [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && HAS_IOMEM [=y]
ERROR: "dsa_unregister_switch" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
ERROR: "dsa_switch_alloc" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
ERROR: "dsa_register_switch" [drivers/net/dsa/vitesse-vsc73xx-core.ko] undefined!
Add the appropriate dependencies.
Fixes: 95711cd5f0 ("net: dsa: vsc73xx: Split vsc73xx driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allow to use devices with disabled iCPU only.
Some devices have pre-initialised iCPU by bootloader.
That state make switch unmanaged. This patch force reset
if device is in unmanaged state. In the result chip lost
internal firmware from RAM and it can be managed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add platform part of vsc73xx driver.
It allows to use chip connected to a parallel memory bus and work in
memory-mapped I/O mode. (aka PI bus in chip manual)
By default device is working in big endian mode.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. But Vitesse chip support also parallel interface.
This patch split driver into two parts: core and spi. It is required
for add support to another managing interface.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a 1ms delay after reset deactivation. Otherwise the chip returns
bogus ID value. This is observed with 88E6390 (Peridot) chip.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A b53 device may configured through an external EEPROM like the switch
device on the Lamobo R1 router board. The configuration of a port may
therefore differ from the reset configuration of the switch.
The switch configuration reported by the DSA subsystem is different until
the port is configured by DSA i.e. a port can be active, while the DSA
subsystem reports the port is inactive. Disable all ports and not only
the unused ones to put all ports into a well defined state.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a better way to signal this, perhaps in phylink_validate, but
for now just print this error message as guidance for other people
looking at this driver's code while trying to rework PHYLINK.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLINK being designed with PHYs in mind that can change MII protocol,
for correct operation it is necessary to ensure that the PHY interface
mode stays the same (otherwise clear the supported bit mask, as
required).
Because this is just a hypothetical situation for now, we don't bother
to check whether we could actually support the new PHY interface mode.
Actually we could modify the xMII table, reset the switch and send an
updated static configuration, but adding that would just be dead code.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been pointed out that PHYLINK can call mac_config only to update
the phy_interface_type and without knowing what the AN results are.
Experimentally, when this was observed to happen, state->link was also
unset, and therefore was used as a proxy to ignore this call. However it
is also suggested that state->link is undefined for this callback and
should not be relied upon.
So let the previously-dead codepath for SPEED_UNKNOWN be called, and
update the comment to make sure the MAC's behavior is sane.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
