This will allow md/raid to know why the unplug was called,
and will be able to act according - if !from_schedule it
is safe to perform tasks which could themselves schedule.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Both md and umem has similar code for getting notified on an
blk_finish_plug event.
Centralize this code in block/ and allow each driver to
provide its distinctive difference.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SYSTEM_SUSPEND_DISK system state is never used, so drop it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge emailed kgdb dmesg fixups patches from Anton Vorontsov:
"The dmesg command appears to be broken after the printk rework. The
old logic in the kdb code makes no sense in terms of current
printk/logging storage format, and KDB simply hangs forever upon
entering 'dmesg' command.
The first patch revives the command by switching to kmsg_dumper
iterator. As a side-effect, the code is now much more simpler.
A few changes were needed in the printk.c: we needed unlocked variant
of the kmsg_dumper iterator, but these can surely wait for 3.6.
It's probably too late even for the first patch to go to 3.5, but I'll
try to convince otherwise. :-) Here we go:
- The current code is broken for sure, and has no hope to work at
all. It is a regression
- The new code works for me, and probably works for everyone else;
- If it compiles (and I urge everyone to compile-test it on your
setup), it hardly can make things worse."
* Merge emailed patches from Anton Vorontsov: (4 commits)
kdb: Switch to nolock variants of kmsg_dump functions
printk: Implement some unlocked kmsg_dump functions
printk: Remove kdb_syslog_data
kdb: Revive dmesg command
If used from KDB, the locked variants are prone to deadlocks (suppose we
got to the debugger w/ the logbuf lock held).
So, we have to implement a few routines that grab no logbuf lock.
Yet we don't need these functions in modules, so we don't export them.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull last minute Ceph fixes from Sage Weil:
"The important one fixes a bug in the socket failure handling behavior
that was turned up in some recent failure injection testing. The
other two are minor bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: endian bug in rbd_req_cb()
rbd: Fix ceph_snap_context size calculation
libceph: fix messenger retry
Commit a7a20d1039 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d01 ("fix async probe
regression"), so that same commit a7a20d1039 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ancient times, the messenger could both initiate and accept connections.
An artifact if that was data structures to store/process an incoming
ceph_msg_connect request and send an outgoing ceph_msg_connect_reply.
Sadly, the negotiation code was referencing those structures and ignoring
important information (like the peer's connect_seq) from the correct ones.
Among other things, this fixes tight reconnect loops where the server sends
RETRY_SESSION and we (the client) retries with the same connect_seq as last
time. This bug pretty easily triggered by injecting socket failures on the
MDS and running some fs workload like workunits/direct_io/test_sync_io.
Signed-off-by: Sage Weil <sage@inktank.com>
This renames CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND to encourage future
reuse of the capability in question in related cases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=oZrz
-----END PGP SIGNATURE-----
Merge tag 'pm-post-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull a last-minute PM update from Rafael J. Wysocki:
"This renames CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND to encourage future
reuse of the capability in question in related cases."
* tag 'pm-post-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Rename CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND
As discussed in
http://thread.gmane.org/gmane.linux.kernel/1249726/focus=1288990,
the capability introduced in 4d7e30d989
to govern EPOLLWAKEUP seems misnamed: this capability is about governing
the ability to suspend the system, not using a particular API flag
(EPOLLWAKEUP). We should make the name of the capability more general
to encourage reuse in related cases. (Whether or not this capability
should also be used to govern the use of /sys/power/wake_lock is a
question that needs to be separately resolved.)
This patch renames the capability to CAP_BLOCK_SUSPEND. In order to ensure
that the old capability name doesn't make it out into the wild, could you
please apply and push up the tree to ensure that it is incorporated
for the 3.5 release.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull networking fixes from David Miller:
1) IPVS oops'ers:
a) Should not reset skb->nf_bridge in forwarding hook (Lin Ming)
b) 3.4 commit can cause ip_vs_control_cleanup to be invoked after
the ipvs_core_ops are unregistered during rmmod (Julian ANastasov)
2) ixgbevf bringup failure can crash in TX descriptor cleanup
(Alexander Duyck)
3) AX25 switch missing break statement hoses ROSE sockets (Alan Cox)
4) CAIF accesses freed per-net memory (Sjur Brandeland)
5) Network cgroup code has out-or-bounds accesses (Eric DUmazet), and
accesses freed memory (Gao Feng)
6) Fix a crash in SCTP reported by Dave Jones caused by freeing an
association still on a list (Neil HOrman)
7) __netdev_alloc_skb() regresses on GFP_DMA using drivers because that
GFP flag is not being retained for the allocation (Eric Dumazet).
8) Missing NULL hceck in sch_sfb netlink message parsing (Alan Cox)
9) bnx2 crashes because TX index iteration is not bounded correctly
(Michael Chan)
10) IPoIB generates warnings in TCP queue collapsing (via
skb_try_coalesce) because it does not set skb->truesize correctly
(Eric Dumazet)
11) vlan_info objects leak for the implicit vlan with ID 0 (Amir
Hanania)
12) A fix for TX time stamp handling in gianfar does not transfer socket
ownership from one packet to another correctly, resulting in a
socket write space imbalance (Eric Dumazet)
13) Julia Lawall found several cases where we do a list iteration, and
then at the loop termination unconditionally assume we ended up with
real list object, rather than the list head itself (CNIC, RXRPC,
mISDN).
14) The bonding driver handles procfs moving incorrectly when a device
it manages is moved from one namespace to another (Eric Biederman)
15) Missing memory barriers in stmmac descriptor accesses result in
various crashes (Deepak Sikri)
16) Fix handling of broadcast packets in batman-adv (Simon Wunderlich)
17) Properly check the sanity of sendmsg() lengths in ieee802154's
dgram_sendmsg(). Dave Jones and others have hit and reported this
bug (Sasha Levin)
18) Some drivers (b44 and b43legacy) on 64-bit machines stopped working
because of how netdev_alloc_skb() was adjusted. Such drivers should
now use alloc_skb() for obtaining bounce buffers. (Eric Dumazet)
19) atl1c mis-managed it's link state in that it stops the queue by hand
on link down. The generic networking takes care of that and this
double stop locks the queue down. So simply removing the driver's
queue stop call fixes the problem (Cloud Ren)
20) Fix out-of-memory due to mis-accounting in net_em packet scheduler
(Eric Dumazet)
21) If DCB and SR-IOV are configured at the same time in IXGBE the chip
will hang because this is not supported (Alexander Duyck)
22) A commit to stop drivers using netdev->base_addr broke the CNIC
driver (Michael Chan)
23) Timeout regression in ipset caused by an attempt to fix an overflow
bug (Jozsef Kadlecsik).
24) mac80211 minstrel code allocates memory using incorrect size
(Thomas Huehn)
25) llcp_sock_getname() needs to check for a NULL device otherwise we
OOPS (Sasha Levin)
26) mwifiex leaks memory (Bing Zhao)
27) Propagate iwlwifi fix to iwlegacy, even when we're not associated
we need to monitor for stuck queues in the watchdog handler
(Stanislaw Geuszka)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
ipvs: fix oops in ip_vs_dst_event on rmmod
ipvs: fix oops on NAT reply in br_nf context
ixgbevf: Fix panic when loading driver
ax25: Fix missing break
MAINTAINERS: reflect actual changes in IEEE 802.15.4 maintainership
caif: Fix access to freed pernet memory
net: cgroup: fix access the unallocated memory in netprio cgroup
ixgbevf: Prevent RX/TX statistics getting reset to zero
sctp: Fix list corruption resulting from freeing an association on a list
net: respect GFP_DMA in __netdev_alloc_skb()
e1000e: fix test for PHY being accessible on 82577/8/9 and I217
e1000e: Correct link check logic for 82571 serdes
sch_sfb: Fix missing NULL check
bnx2: Fix bug in bnx2_free_tx_skbs().
IPoIB: fix skb truesize underestimatiom
net: Fix memory leak - vlan_info struct
gianfar: fix potential sk_wmem_alloc imbalance
drivers/net/ethernet/broadcom/cnic.c: remove invalid reference to list iterator variable
net/rxrpc/ar-peer.c: remove invalid reference to list iterator variable
drivers/isdn/mISDN/stack.c: remove invalid reference to list iterator variable
...
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"Another set of minor fixups for recently merged Contiguous Memory
Allocator and ARM DMA-mapping changes. Those patches fix mysterious
crashes on systems with CMA and Himem enabled as well as some corner
cases caused by typical off-by-one bug."
* 'fixes-for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: modify condition check while freeing pages
mm: cma: fix condition check when setting global cma area
mm: cma: don't replace lowmem pages with highmem
Pull RCU, perf, and scheduler fixes from Ingo Molnar.
The RCU fix is a revert for an optimization that could cause deadlocks.
One of the scheduler commits (164c33c6ad "sched: Fix fork() error path
to not crash") is correct but not complete (some architectures like Tile
are not covered yet) - the resulting additional fixes are still WIP and
Ingo did not want to delay these pending fixes. See this thread on
lkml:
[PATCH] fork: fix error handling in dup_task()
The perf fixes are just trivial oneliners.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "rcu: Move PREEMPT_RCU preemption to switch_to() invocation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix segfault with report and mixed guestmount use
perf kvm: Fix regression with guest machine creation
perf script: Fix format regression due to libtraceevent merge
ring-buffer: Fix accounting of entries when removing pages
ring-buffer: Fix crash due to uninitialized new_pages list head
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS/sched: Update scheduler file pattern
sched/nohz: Rewrite and fix load-avg computation -- again
sched: Fix fork() error path to not crash
Pull the leap second fixes from Thomas Gleixner:
"It's a rather large series, but well discussed, refined and reviewed.
It got a massive testing by John, Prarit and tip.
In theory we could split it into two parts. The first two patches
f55a6faa38: hrtimer: Provide clock_was_set_delayed()
4873fa070a: timekeeping: Fix leapsecond triggered load spike issue
are merely preventing the stuff loops forever issues, which people
have observed.
But there is no point in delaying the other 4 commits which achieve
full correctness into 3.6 as they are tagged for stable anyway. And I
rather prefer to have the full fixes merged in bulk than a "prevent
the observable wreckage and deal with the hidden fallout later"
approach."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Update hrtimer base offsets each hrtimer_interrupt
timekeeping: Provide hrtimer update function
hrtimers: Move lock held region in hrtimer_interrupt()
timekeeping: Maintain ktime_t based offsets for hrtimers
timekeeping: Fix leapsecond triggered load spike issue
hrtimer: Provide clock_was_set_delayed()
memblock_free_reserved_regions() calls memblock_free(), but
memblock_free() would double reserved.regions too, so we could free the
old range for reserved.regions.
Also tj said there is another bug which could be related to this.
| I don't think we're saving any noticeable
| amount by doing this "free - give it to page allocator - reserve
| again" dancing. We should just allocate regions aligned to page
| boundaries and free them later when memblock is no longer in use.
in that case, when DEBUG_PAGEALLOC, will get panic:
memblock_free: [0x0000102febc080-0x0000102febf080] memblock_free_reserved_regions+0x37/0x39
BUG: unable to handle kernel paging request at ffff88102febd948
IP: [<ffffffff836a5774>] __next_free_mem_range+0x9b/0x155
PGD 4826063 PUD cf67a067 PMD cf7fa067 PTE 800000102febd160
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU 0
Pid: 0, comm: swapper Not tainted 3.5.0-rc2-next-20120614-sasha #447
RIP: 0010:[<ffffffff836a5774>] [<ffffffff836a5774>] __next_free_mem_range+0x9b/0x155
See the discussion at https://lkml.org/lkml/2012/6/13/469
So try to allocate with PAGE_SIZE alignment and free it later.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After commit f5bf18fa22 ("bootmem/sparsemem: remove limit constraint
in alloc_bootmem_section"), usemap allocations may easily be placed
outside the optimal section that holds the node descriptor, even if
there is space available in that section. This results in unnecessary
hotplug dependencies that need to have the node unplugged before the
section holding the usemap.
The reason is that the bootmem allocator doesn't guarantee a linear
search starting from the passed allocation goal but may start out at a
much higher address absent an upper limit.
Fix this by trying the allocation with the limit at the section end,
then retry without if that fails. This keeps the fix from f5bf18fa22
of not panicking if the allocation does not fit in the section, but
still makes sure to try to stay within the section at first.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.3.x, 3.4.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To finally fix the infamous leap second issue and other race windows
caused by functions which change the offsets between the various time
bases (CLOCK_MONOTONIC, CLOCK_REALTIME and CLOCK_BOOTTIME) we need a
function which atomically gets the current monotonic time and updates
the offsets of CLOCK_REALTIME and CLOCK_BOOTTIME with minimalistic
overhead. The previous patch which provides ktime_t offsets allows us
to make this function almost as cheap as ktime_get() which is going to
be replaced in hrtimer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/1341960205-56738-7-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
clock_was_set() cannot be called from hard interrupt context because
it calls on_each_cpu().
For fixing the widely reported leap seconds issue it is necessary to
call it from hard interrupt context, i.e. the timer tick code, which
does the timekeeping updates.
Provide a new function which denotes it in the hrtimer cpu base
structure of the cpu on which it is called and raise the hrtimer
softirq. We then execute the clock_was_set() notificiation from
softirq context in run_hrtimer_softirq(). The hrtimer softirq is
rarely used, so polling the flag there is not a performance issue.
[ tglx: Made it depend on CONFIG_HIGH_RES_TIMERS. We really should get
rid of all this ifdeffery ASAP ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1341960205-56738-2-git-send-email-johnstul@us.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a set of three fixes for data corruption (libsas task file), oops
causing (NULL in scsi_cmd_to_driver) and driver failure (bnx2i). The oops
caused by the NULL in scsi_cmd_to_driver() manifests in scsi_eh_send_cmd() and
has been seen by several people now.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP/S5TAAoJEDeqqVYsXL0MM2EIAMQrBUamIjML5tiKwwD7zZsc
GBNPLFD2PJNvzaRweENU+CwbHYc7ipt9FMHC89dlOR4vStKR/7nxUOnH2c/pnogM
bbU2JCP0iG4IxU8+kcNBKCmysyu5xdd5kh0NOmwMSQrQVlTdfZz4iFXMPtGrK8H6
vfm5w2Y6HUJEXMgmfohDurvLK3L8GvO7E1tKzEJhmfZZqtqnt5vk++tZKCpqf1lH
et29y6Ic+daxHgEBR1gCp11Ywike7e01BJPNnTvpX4XV+E+L7fEDwl2Mb7Rsslh1
L61m4JkR9nDSSH8jD7oqUUlbkx+XTe31M/jj9jiLu0tCxIDgOFFcn6KziM1qINI=
=Ir0I
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes for data corruption (libsas task file),
oops causing (NULL in scsi_cmd_to_driver) and driver failure (bnx2i).
The oops caused by the NULL in scsi_cmd_to_driver() manifests in
scsi_eh_send_cmd() and has been seen by several people now.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bnx2i: Removed the reference to the netdev->base_addr
[SCSI] libsas: fix taskfile corruption in sas_ata_qc_fill_rtf
[SCSI] Fix NULL dereferences in scsi_cmd_to_driver
Here are a few fixes and new device ids for the 3.5-rc6 tree.
The PCI changes resolve a long-standing issue with resuming some EHCI
controllers. It has been acked by the PCI maintainer, and he asked for it to
go through my USB tree instead of his.
The xhci patches also resolve a number of reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/9hDgACgkQMUfUDdst+yk7KACg1/6PU/Zni57kEvjypRmbMF66
SHoAoKdR7HFUvfgnq/HbUVlAC5sM+AJH
=zxcV
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a few fixes and new device ids for the 3.5-rc6 tree.
The PCI changes resolve a long-standing issue with resuming some EHCI
controllers. It has been acked by the PCI maintainer, and he asked
for it to go through my USB tree instead of his.
The xhci patches also resolve a number of reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
PCI: EHCI: fix crash during suspend on ASUS computers
USB: cdc-wdm: fix lockup on error in wdm_read
USB: metro-usb: fix tty_flip_buffer_push use
USB: option: Add MEDIATEK product ids
USB: option: add ZTE MF60
xhci: Fix hang on back-to-back Set TR Deq Ptr commands.
usb: Add support for root hub port status CAS
- Invalid context restore on bank 0 for OMAP driver in
runtime suspend/resume cycle
- Check for NULL platform data in sta-2x11 driver
- Constrain selection of the V1 MSM GPIO driver to applicable
platforms (Kconfig issue)
- Make sure the correct output value is set in the wm8994 driver
- Export devm_gpio_request_one() so it can be used in modules.
Apparently some in-kernel modules can be configured to use this
leading to breakage.
- Check that the GPIO is valid in the lantiq driver
- Fix the flag bits introduced for v3.5, so they don't overlap
- Fix a device tree intialization bug for imx21-compatible devices
- Carry over the OF node to the TPS65910 GPIO chip struct
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GIRC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Yes, this is a *LATE* GPIO pull request with fixes for v3.5.
Grant moved across the planet and accidentally fell off the grid, so
he asked me to take over the GPIO merges for a while 10 days ago.
Since then I went over the archives and collected this pile of fixes,
and pulled two of them from the TI maintainer Kevin Hilman. Then
waited for them to at least hit linux-next once or twice."
GPIO fixes for v3.5:
- Invalid context restore on bank 0 for OMAP driver in runtime
suspend/resume cycle
- Check for NULL platform data in sta-2x11 driver
- Constrain selection of the V1 MSM GPIO driver to applicable platforms
(Kconfig issue)
- Make sure the correct output value is set in the wm8994 driver
- Export devm_gpio_request_one() so it can be used in modules.
Apparently some in-kernel modules can be configured to use this
leading to breakage.
- Check that the GPIO is valid in the lantiq driver
- Fix the flag bits introduced for v3.5, so they don't overlap
- Fix a device tree intialization bug for imx21-compatible devices
- Carry over the OF node to the TPS65910 GPIO chip struct
* tag 'fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65910: initialize of_node of gpio_chip
gpio/mxc: make irqs work for fsl,imx21-gpio devices
gpio: fix bits conflict for gpio flags
mips: pci-lantiq: Fix check for valid gpio
gpio: export devm_gpio_request_one
gpiolib: wm8994: Pay attention to the value set when enabling as output
gpio/msm_v1: CONFIG_GPIO_MSM_V1 is only available on three SoCs
gpio-sta2x11: don't use pdata if null
gpio/omap: fix invalid context restore of gpio bank-0
gpio/omap: fix irq loss while in idle with debounce on
Quite a few ASUS computers experience a nasty problem, related to the
EHCI controllers, when going into system suspend. It was observed
that the problem didn't occur if the controllers were not put into the
D3 power state before starting the suspend, and commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers) was created to do this.
It turned out this approach messed up other computers that didn't have
the problem -- it prevented USB wakeup from working. Consequently
commit c2fb8a3fa2 (USB: add
NO_D3_DURING_SLEEP flag and revert 151b612847) was merged; it
reverted the earlier commit and added a whitelist of known good board
names.
Now we know the actual cause of the problem. Thanks to AceLan Kao for
tracking it down.
According to him, an engineer at ASUS explained that some of their
BIOSes contain a bug that was added in an attempt to work around a
problem in early versions of Windows. When the computer goes into S3
suspend, the BIOS tries to verify that the EHCI controllers were first
quiesced by the OS. Nothing's wrong with this, but the BIOS does it
by checking that the PCI COMMAND registers contain 0 without checking
the controllers' power state. If the register isn't 0, the BIOS
assumes the controller needs to be quiesced and tries to do so. This
involves making various MMIO accesses to the controller, which don't
work very well if the controller is already in D3. The end result is
a system hang or memory corruption.
Since the value in the PCI COMMAND register doesn't matter once the
controller has been suspended, and since the value will be restored
anyway when the controller is resumed, we can work around the BIOS bug
simply by setting the register to 0 during system suspend. This patch
(as1590) does so and also reverts the second commit mentioned above,
which is now unnecessary.
In theory we could do this for every PCI device. However to avoid
introducing new problems, the patch restricts itself to EHCI host
controllers.
Finally the affected systems can suspend with USB wakeup working
properly.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=37632
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=42728
Based-on-patch-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Javier Marcet <jmarcet@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Tested-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: stable <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
were reported by Fernando Guzman Lugo.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJP+dsKAAoJELLolMlTRIoMOTEQAK2WOgW4ygXDOfhwZCj4ooXG
Mk9PUQlEBfEufvKmK/Oh3xDVeP0i4+3BeWZ4Kgmas689SJc+LIbLSS0HtARcYF1+
ZTEj7Gnax3P3tD6GxwU5bf+jrirCbr5sSeDa7p5jh017zVsZ5MVYOYvWXKQtYAZg
hi6m2AqOUfkI3yOnWRbNMds+x3TTwpLC/3mT9mcFiJ/3L9SGx22SVfkRIa8tstjg
i0eJDTu9cbHHZ7wtuGQoVZDO5kHLi7dPKnFTiFat8dklaSNMzNBrs5Tl4DT0XA3s
tzb+BrnkddL2L36cC0XIyV1L/tQCdtAWLRFx5SDfpXKNQcYpqlMAteaAXdhf4Tjl
kJapLhGeTVRSED6TvYX9XMFbi4U8PBSBvHd4VMryN1jGcmslE3UYCPIoqOL/aIZP
dc9POY6JM9r/pMlzhQ6VUmTiecCVeCJyCh8x8r1wj7V1mC1nCxDskxObibHFjRPk
4xdmke0+UR3fn4/aA/PRZbiy3kpT84lK9SoPlzUKLLBMzJ3KMLl5Dug2+Y8Aeutn
gBxt9x+FA4UgmS62St97Cu7qbzWvAbpl95rFD4aIANMNxU9OkcjgWaB7aJzr8WWt
j8Z2OkT0WW4ka60sGj0YxAEDlKhxC8f1lzD5tuJgmVFEbXhNTZaw+GG/ZwIqb5bq
g7KQY8FnGDETO9Tew1QQ
=nbt8
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg
Pull rpmsg fixes from Ohad Ben-Cohen:
"Fixing two (somewhat rare) endpoint-related race issues, both of which
were reported by Fernando Guzman Lugo."
* tag 'rpmsg-3.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/rpmsg:
rpmsg: make sure inflight messages don't invoke just-removed callbacks
rpmsg: avoid premature deallocation of endpoints
Hans reports that he's still hitting:
BUG: unable to handle kernel NULL pointer dereference at 000000000000027c
IP: [<ffffffff813615db>] netlink_has_listeners+0xb/0x60
PGD 0
Oops: 0000 [#3] PREEMPT SMP
CPU 0
It happens when adding a number of containers with do:
nfct_query(h, NFCT_Q_CREATE, ct);
and most likely one namespace shuts down.
this problem was supposed to be fixed by:
70e9942 netfilter: nf_conntrack: make event callback registration per-netns
Still, it was missing one rcu_access_pointer to check if the callback
is set or not.
Reported-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
fill_result_tf() grabs the taskfile flags from the originating qc which
sas_ata_qc_fill_rtf() promptly overwrites. The presence of an
ata_taskfile in the sata_device makes it tempting to just copy the full
contents in sas_ata_qc_fill_rtf(). However, libata really only wants
the fis contents and expects the other portions of the taskfile to not
be touched by ->qc_fill_rtf. To that end store a fis buffer in the
sata_device and use ata_tf_from_fis() like every other ->qc_fill_rtf()
implementation.
Cc: <stable@vger.kernel.org>
Reported-by: Praveen Murali <pmurali@logicube.com>
Tested-by: Praveen Murali <pmurali@logicube.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The documentation didn't actually mention how to enable no_new_privs.
This also adds a note about possible interactions between
no_new_privs and LSMs (i.e. why teaching systemd to set no_new_privs
is not necessarily a good idea), and it references the new docs
from include/linux/prctl.h.
Suggested-by: Rob Landley <rob@landley.net>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull ocfs2 fixes from Joel Becker.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
aio: make kiocb->private NUll in init_sync_kiocb()
ocfs2: Fix bogus error message from ocfs2_global_read_info
ocfs2: for SEEK_DATA/SEEK_HOLE, return internal error unchanged if ocfs2_get_clusters_nocache() or ocfs2_inode_lock() call failed.
ocfs2: use spinlock irqsave for downconvert lock.patch
ocfs2: Misplaced parens in unlikley
ocfs2: clear unaligned io flag when dio fails
Pull input layer fixes from Dmitry Torokhov:
"Two fixes for regressions in Wacom driver and fixes for drivers using
threaded IRQ framework without specifying IRQF_ONESHOT."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: request threaded-only IRQs with IRQF_ONESHOT
Input: wacom - don't retrieve touch_max when it is predefined
Input: wacom - fix retrieving touch_max bug
Input: fix input.h kernel-doc warning
dev_set_cma_area incorrectly assigned cma to global area on first call
due to incorrect check. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Pull KVM fix from Marcelo Tosatti:
"Memory leak and oops on the x86 mmu code, and sanitization of the
KVM_IRQFD ioctl."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: fix shrinking page from the empty mmu
KVM: fix fault page leak
KVM: Sanitize KVM_IRQFD flags
KVM: Add missing KVM_IRQFD API documentation
KVM: Pass kvm_irqfd to functions
Thanks to Charles Wang for spotting the defects in the current code:
- If we go idle during the sample window -- after sampling, we get a
negative bias because we can negate our own sample.
- If we wake up during the sample window we get a positive bias
because we push the sample to a known active period.
So rewrite the entire nohz load-avg muck once again, now adding
copious documentation to the code.
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Reported-and-tested-by: Charles Wang <muming.wq@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1340373782.18025.74.camel@twins
[ minor edits ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The bit 2 and 3 in GPIO flag are allocated for the
flag OPEN_DRAIN/OPEN_SOURCE. These bits are reused
for the flag EXPORT/EXPORT_CHANGEABLE and so creating
conflict.
Fix this conflict by assigning bit 4 and 5 for the
flag EXPORT/EXPORT_CHANGEABLE.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ocfs2 uses kiocb.*private as a flag of unsigned long size. In
commit a11f7e6 ocfs2: serialize unaligned aio, the unaligned
io flag is involved in it to serialize the unaligned aio. As
*private is not initialized in init_sync_kiocb() of do_sync_write(),
this unaligned io flag may be unexpectly set in an aligned dio.
And this will cause OCFS2_I(inode)->ip_unaligned_aio decreased
to -1 in ocfs2_dio_end_io(), thus the following unaligned dio
will hang forever at ocfs2_aiodio_wait() in ocfs2_file_aio_write().
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: stable@vger.kernel.org
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Joel Becker <jlbec@evilplan.org>
When inbound messages arrive, rpmsg core looks up their associated
endpoint (by destination address) and then invokes their callback.
We've made sure that endpoints will never be de-allocated after they
were found by rpmsg core, but we also need to protect against the
(rare) scenario where the rpmsg driver was just removed, and its
callback function isn't available anymore.
This is achieved by introducing a callback mutex, which must be taken
before the callback is invoked, and, obviously, before it is removed.
Cc: stable <stable@vger.kernel.org>
Reported-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
When an inbound message arrives, the rpmsg core looks up its
associated endpoint and invokes the registered callback.
If a message arrives while its endpoint is being removed (because
the rpmsg driver was removed, or a recovery of a remote processor
has kicked in) we must ensure atomicity, i.e.:
- Either the ept is removed before it is found
or
- The ept is found but will not be freed until the callback returns
This is achieved by maintaining a per-ept reference count, which,
when drops to zero, will trigger deallocation of the ept.
With this in hand, it is now forbidden to directly deallocate
epts once they have been added to the endpoints idr.
Cc: stable <stable@vger.kernel.org>
Reported-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Pull networking update from David Miller:
1) Fix RX sequence number handling in mwifiex, from Stone Piao.
2) Netfilter ipset mis-compares device names, fix from Florian
Westphal.
3) Fix route leak in ipv6 IPVS, from Eric Dumazet.
4) NFS fixes. Several buffer overflows in NCI layer from Dan
Rosenberg, and release sock OOPS'er fix from Eric Dumazet.
5) Fix WEP handling ath9k, we started using a bit the chip provides to
indicate undecrypted packets but that bit turns out to be unreliable
in certain configurations. Fix from Felix Fietkau.
6) Fix Kconfig dependency bug in wlcore, from Randy Dunlap.
7) New USB IDs for rtlwifi driver from Larry Finger.
8) Fix crashes in qmi_wwan usbnet driver when disconnecting, from Bjørn
Mork.
9) Gianfar driver programs coalescing settings properly in single queue
mode, but does not do so in multi-queue mode. Fix from Claudiu
Manoil.
10) Missing module.h include in davinci_cpdma.c, from Daniel Mack.
11) Need dummy handler for IPSET_CMD_NONE otherwise we crash in ipset if
we get this via nfnetlink, fix from Tomasz Bursztyka.
12) Missing RCU unlock in nfnetlink error path, also from Tomasz.
13) Fix divide by zero in igbvf when the user tries to set an RX
coalescing value of 0 usecs, from Mitch A Williams.
14) We can process SCTP sacks for the wrong transport, oops. Fix from
Neil Horman.
15) Remove hw IP payload checksumming from e1000e driver. This has zery
value in our stack, and turning it on creates a very unintuitive
restriction for users when using jumbo MTUs.
Specifically, when IP payload checksums are on you cannot use both
receive hashing offload and jumbo MTU. Fix from Bruce Allan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
e1000e: remove use of IP payload checksum
sctp: be more restrictive in transport selection on bundled sacks
igbvf: fix divide by zero
netfilter: nfnetlink: fix missing rcu_read_unlock in nfnetlink_rcv_msg
netfilter: ipset: fix crash if IPSET_CMD_NONE command is sent
davinci_cpdma: include linux/module.h
gianfar: Fix RXICr/TXICr programming for multi-queue mode
net: Downgrade CAP_SYS_MODULE deprecated message from error to warning.
net: qmi_wwan: fix Oops while disconnecting
mwifiex: fix memory leak associated with IE manamgement
ath9k: fix panic caused by returning a descriptor we have queued for reuse
mac80211: correct behaviour on unrecognised action frames
ath9k: enable serialize_regmode for non-PCIE AR9287
rtlwifi: rtl8192cu: New USB IDs
NFC: Return from rawsock_release when sk is NULL
iwlwifi: fix activating inactive stations
wlcore: drop INET dependency
ath9k: fix dynamic WEP related regression
NFC: Prevent multiple buffer overflows in NCI
netfilter: update location of my trees
...
Pull block bits from Jens Axboe:
"As vacation is coming up, thought I'd better get rid of my pending
changes in my for-linus branch for this iteration. It contains:
- Two patches for mtip32xx. Killing a non-compliant sysfs interface
and moving it to debugfs, where it belongs.
- A few patches from Asias. Two legit bug fixes, and one killing an
interface that is no longer in use.
- A patch from Jan, making the annoying partition ioctl warning a bit
less annoying, by restricting it to !CAP_SYS_RAWIO only.
- Three bug fixes for drbd from Lars Ellenberg.
- A fix for an old regression for umem, it hasn't really worked since
the plugging scheme was changed in 3.0.
- A few fixes from Tejun.
- A splice fix from Eric Dumazet, fixing an issue with pipe
resizing."
* 'for-linus' of git://git.kernel.dk/linux-block:
scsi: Silence unnecessary warnings about ioctl to partition
block: Drop dead function blk_abort_queue()
block: Mitigate lock unbalance caused by lock switching
block: Avoid missed wakeup in request waitqueue
umem: fix up unplugging
splice: fix racy pipe->buffers uses
drbd: fix null pointer dereference with on-congestion policy when diskless
drbd: fix list corruption by failing but already aborted reads
drbd: fix access of unallocated pages and kernel panic
xen/blkfront: Add WARN to deal with misbehaving backends.
blkcg: drop local variable @q from blkg_destroy()
mtip32xx: Create debugfs entries for troubleshooting
mtip32xx: Remove 'registers' and 'flags' from sysfs
blkcg: fix blkg_alloc() failure path
block: blkcg_policy_cfq shouldn't be used if !CONFIG_CFQ_GROUP_IOSCHED
block: fix return value on cfq_init() failure
mtip32xx: Remove version.h header file inclusion
xen/blkback: Copy id field when doing BLKIF_DISCARD.
Prune this down to just the struct kvm_irqfd so we can avoid
changing function definition for every flag or field we use.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This reverts commit 616c310e83.
(Move PREEMPT_RCU preemption to switch_to() invocation).
Testing by Sasha Levin <levinsasha928@gmail.com> showed that this
can result in deadlock due to invoking the scheduler when one of
the runqueue locks is held. Because this commit was simply a
performance optimization, revert it.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
It was noticed recently that when we send data on a transport, its possible that
we might bundle a sack that arrived on a different transport. While this isn't
a major problem, it does go against the SHOULD requirement in section 6.4 of RFC
2960:
An endpoint SHOULD transmit reply chunks (e.g., SACK, HEARTBEAT ACK,
etc.) to the same destination transport address from which it
received the DATA or control chunk to which it is replying. This
rule should also be followed if the endpoint is bundling DATA chunks
together with the reply chunk.
This patch seeks to correct that. It restricts the bundling of sack operations
to only those transports which have moved the ctsn of the association forward
since the last sack. By doing this we guarantee that we only bundle outbound
saks on a transport that has received a chunk since the last sack. This brings
us into stricter compliance with the RFC.
Vlad had initially suggested that we strictly allow only sack bundling on the
transport that last moved the ctsn forward. While this makes sense, I was
concerned that doing so prevented us from bundling in the case where we had
received chunks that moved the ctsn on multiple transports. In those cases, the
RFC allows us to select any of the transports having received chunks to bundle
the sack on. so I've modified the approach to allow for that, by adding a state
variable to each transport that tracks weather it has moved the ctsn since the
last sack. This I think keeps our behavior (and performance), close enough to
our current profile that I think we can do this without a sysctl knob to
enable/disable it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yaseivch <vyasevich@gmail.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Reported-by: Michele Baldessari <michele@redhat.com>
Reported-by: sorin serban <sserban@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning. This struct member was removed in commit
875682648b ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.
Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking update from David Miller:
1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.
2) Add device IDs for AR3011 and AR3012 bluetooth chips. From
Giancarlo Formicuccia and Marek Vasut.
3) Fix wireless regulatory deadlock, from Eliad Peller.
4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.
5) Revert the two commits that added skb_orphan_try(), it causes
erratic bonding behavior with UDP clients and the gains it used to
give are mostly no longer happening due to how BQL works. From Eric
Dumazet.
6) It took two tries, but Thomas Graf fixed a problem wherein we
registered ipv6 routing procfs files before their backend data were
initialized properly.
7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.
8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
Jason Wang.
9) Fix use of stale SKB data pointer after skb_linearize() call in
batman-adv, from Antonio Quartulli.
10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
Duyck.
11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
Mork.
12) Fix suspend/resume and open failure handling in usbnet from Ming
Lei.
13) Attempt to fix device r8169 hangs for certain chips, from Francois
Romieu.
14) Fix advancement of RX dirty pointer in some situations in sh_eth
driver, from Yoshihiro Shimoda.
15) Attempt to fix restart of IPV6 routing table dumps when there is an
intervening table update. From Eric Dumazet.
16) Respect security_inet_conn_request() return value in ipv6 TCP. From
Neal Cardwell.
17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.
18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
splats, from Eric Dumazet.
19) Make sure all bridge devices, regardless of whether they were
created via netlink or ioctls, have their rtnetlink ops hooked up.
From Thomas Graf and Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
9p: fix min_t() casting in p9pdu_vwritef()
can: flexcan: use be32_to_cpup to handle the value of dt entry
xen/netfront: teardown the device before unregistering it.
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
vhost: use USER_DS in vhost_worker thread
ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
net: l2tp_eth: use LLTX to avoid LOCKDEP splats
mac802154: add missed braces
net: l2tp_eth: fix l2tp_eth_dev_xmit race
net/mlx4_en: Release QP range in free_resources
net/mlx4: Use single completion vector after NOP failure
net/mlx4_en: Set correct port parameters during device initialization
ipheth: add support for iPad
caif-hsi: Add missing return in error path
caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
caif: Clear shutdown mask to zero at reconnect.
tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
ipv6: fib: fix fib dump restart
batman-adv: fix race condition in TT full-table replacement
batman-adv: only drop packets of known wifi clients
...
Here are some small USB gadget bugfixes, and a few new USB device ids added to
some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/rYS0ACgkQMUfUDdst+ynuGQCfYYD43H+BtubcS+jt5N61/5lM
wUgAoM1wru64Kfox9v6U8g21AnLeJOhJ
=e1xG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB gadget bugfixes, and a few new USB device ids
added to some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: CP210x Add 10 Device IDs
USB: option: Add USB ID for Novatel Ovation MC551
usb: phy: Fix Kconfig dependency for Phy drivers
usb-storage: revert commit afff07e61a (Add 090c:1000 to unusal-devs)
SCSI & usb-storage: add try_rc_10_first flag
usb: musb: host: release dma channels if no active io
usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
usb: otg: twl6030-usb: Fix twl writes
USB: option: add id for Cellient MEN-200
usb: dwc3: fix giveback of queued request in ep_dequeue
usb: gadget: Complete fsl qe/udc driver conversion
Currently, request_queue has one request_list to allocate requests
from regardless of blkcg of the IO being issued. When the unified
request pool is used up, cfq proportional IO limits become meaningless
- whoever grabs the next request being freed wins the race regardless
of the configured weights.
This can be easily demonstrated by creating a blkio cgroup w/ very low
weight, put a program which can issue a lot of random direct IOs there
and running a sequential IO from a different cgroup. As soon as the
request pool is used up, the sequential IO bandwidth crashes.
This patch implements per-blkg request_list. Each blkg has its own
request_list and any IO allocates its request from the matching blkg
making blkcgs completely isolated in terms of request allocation.
* Root blkcg uses the request_list embedded in each request_queue,
which was renamed to @q->root_rl from @q->rq. While making blkcg rl
handling a bit harier, this enables avoiding most overhead for root
blkcg.
* Queue fullness is properly per request_list but bdi isn't blkcg
aware yet, so congestion state currently just follows the root
blkcg. As writeback isn't aware of blkcg yet, this works okay for
async congestion but readahead may get the wrong signals. It's
better than blkcg completely collapsing with shared request_list but
needs to be improved with future changes.
* After this change, each block cgroup gets a full request pool making
resource consumption of each cgroup higher. This makes allowing
non-root users to create cgroups less desirable; however, note that
allowing non-root users to directly manage cgroups is already
severely broken regardless of this patch - each block cgroup
consumes kernel memory and skews IO weight (IO weights are not
hierarchical).
v2: queue-sysfs.txt updated and patch description udpated as suggested
by Vivek.
v3: blk_get_rl() wasn't checking error return from
blkg_lookup_create() and may cause oops on lookup failure. Fix it
by falling back to root_rl on blkg lookup failures. This problem
was spotted by Rakesh Iyer <rni@google.com>.
v4: Updated to accomodate 458f27a982 "block: Avoid missed wakeup in
request waitqueue". blk_drain_queue() now wakes up waiters on all
blkg->rl on the target queue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
