Add a way to configure if poll() should wait forever for an event, the
number of packets that should be sent for each and if there should be
any delay between packets.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add series of tests for valid and invalid nexthop specs for IPv6.
$ TEST=fib_nexthop_test ./fib_tests.sh
...
IPv6 nexthop tests
TEST: Directly connected nexthop, unicast address [ OK ]
TEST: Directly connected nexthop, unicast address with device [ OK ]
TEST: Gateway is linklocal address [ OK ]
TEST: Gateway is linklocal address, no device [ OK ]
TEST: Gateway can not be local unicast address [ OK ]
TEST: Gateway can not be local unicast address, with device [ OK ]
TEST: Gateway can not be a local linklocal address [ OK ]
TEST: Gateway can be local address in a VRF [ OK ]
TEST: Gateway can be local address in a VRF, with device [ OK ]
TEST: Gateway can be local linklocal address in a VRF [ OK ]
TEST: Redirect to VRF lookup [ OK ]
TEST: VRF route, gateway can be local address in default VRF [ OK ]
TEST: VRF route, gateway can not be a local address [ OK ]
TEST: VRF route, gateway can not be a local addr with device [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to run just a specific fib test by setting the TEST
environment variable.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 'ip -netns testns' with the alias IP. Shortens the line lengths
and makes running the commands manually a bit easier.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tile architecture port was added by Chris Metcalf in 2010, and
maintained until early 2018 when he orphaned it due to his departure
from Mellanox, and nobody else stepped up to maintain it. The product
line is still around in the form of the BlueField SoC, but no longer
uses the Tile architecture.
There are also still products for sale with Tile-GX SoCs, notably the
Mikrotik CCR router family. The products all use old (linux-3.3) kernels
with lots of patches and won't be upgraded by their manufacturers. There
have been efforts to port both OpenWRT and Debian to these, but both
projects have stalled and are very unlikely to be continued in the future.
Given that we are reasonably sure that nobody is still using the port
with an upstream kernel any more, it seems better to remove it now while
the port is in a good shape than to let it bitrot for a few years first.
Cc: Chris Metcalf <chris.d.metcalf@gmail.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: http://www.mellanox.com/page/npu_multicore_overview
Link: https://jenkins.debian.net/view/rebootstrap/job/rebootstrap_tilegx_gcc7/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
test_stacktrace_build_id() is added. It accesses tracepoint urandom_read
with "dd" and "urandom_read" and gathers stack traces. Then it reads the
stack traces from the stackmap.
urandom_read is a statically link binary that reads from /dev/urandom.
test_stacktrace_build_id() calls readelf to read build ID of urandom_read
and compares it with build ID from the stackmap.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Now that we have a kconfig checker just use that instead of relying
on testing a sysfs directory being present, since our requirements
are spelled out.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a kernel is not built with:
CONFIG_HAS_FW_LOADER_USER_HELPER_FALLBACK=y
We don't currently enable testing fw_fallback.sh. For kernels that
still enable the fallback mechanism, its possible to use the async
request firmware API call request_firmware_nowait() using the custom
interface to use the fallback mechanism, so we should be able to test
this but we currently cannot.
We can enable testing without CONFIG_HAS_FW_LOADER_USER_HELPER_FALLBACK=y
by relying on /proc/config.gz (CONFIG_IKCONFIG_PROC), if present. If you
don't have this we'll have no option but to rely on old heuristics for now.
We stuff the new kconfig_has() helper into our shared library as we'll
later expando on its use elsewhere.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We'll expland on this later, for now just add basic module checker.
While at it, move this all to use /bin/bash as we'll have much more
flexibility with it.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tests to check:
- bind-mounts from /dev/pts/ptmx to /dev/ptmx work
- non-standard mounts of devpts work
- bind-mounts of /dev/pts/ptmx to locations that do not resolve to a valid
slave pty path under the originating devpts mount fail
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
POPF is currently broken -- add tests to catch the error. This
results in:
[RUN] POPF with VIP set and IF clear from vm86 mode
[INFO] Exited vm86 mode due to STI
[FAIL] Incorrect return reason (started at eip = 0xd, ended at eip = 0xf)
because POPF currently fails to check IF before reporting a pending
interrupt.
This patch also makes the FAIL message a bit more informative.
Reported-by: Bart Oldeman <bartoldeman@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/a16270b5cfe7832d6d00c479d0f871066cbdb52b.1521003603.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix a logic error that caused the test to exit with 0 even if test
cases failed.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bartoldeman@gmail.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/b1cc37144038958a469c8f70a5f47a6a5638636a.1521003603.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some processor revisions do not support transactional memory, and
additionally kernel support can be disabled. In either case the
tm-unavailable test should be skipped, otherwise it will fail with
a SIGILL.
That commit also sets this selftest to be called through the test
harness as it's done for other TM selftests.
Finally, it avoids using "ping" as a thread name since it's
ambiguous and can be confusing when shown, for instance,
in a kernel backtrace log.
Fixes: 77fad8bfb1 ("selftests/powerpc: Check FP/VEC on exception in TM")
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure that kernel is throwing away the suspended transaction when
sigreturn() is called otherwise it if fails to restore the signal
frame's TM SPRS.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Add have_htm() check, minor formatting, add SPDX tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some users want to be able to run the tests without a configuration file
which is useful when one needs to test both virtual and physical
interfaces on the same machine.
Move the defines that set the type of interface to create and whether to
create it away from the optional configuration file to the library like
the rest of the defines.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 gives a false sense of success when the required modules did
not even manage to be initialized and register the required net devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already return an error when some dependencies (e.g., 'jq') are
missing so lets be consistent and do that for all.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the VLAN-aware bridge test, test the VLAN-unaware bridge and
make sure that ping, FDB learning and flooding work as expected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86/pti updates from Thomas Gleixner:
"Yet another pile of melted spectrum related updates:
- Drop native vsyscall support finally as it causes more trouble than
benefit.
- Make microcode loading more robust. There were a few issues
especially related to late loading which are now surfacing because
late loading of the IB* microcodes addressing spectre issues has
become more widely used.
- Simplify and robustify the syscall handling in the entry code
- Prevent kprobes on the entry trampoline code which lead to kernel
crashes when the probe hits before CR3 is updated
- Don't check microcode versions when running on hypervisors as they
are considered as lying anyway.
- Fix the 32bit objtool build and a coment typo"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Fix kernel crash when probing .entry_trampoline code
x86/pti: Fix a comment typo
x86/microcode: Synchronize late microcode loading
x86/microcode: Request microcode on the BSP
x86/microcode/intel: Look into the patch cache first
x86/microcode: Do not upload microcode if CPUs are offline
x86/microcode/intel: Writeback and invalidate caches before updating microcode
x86/microcode/intel: Check microcode revision before updating sibling threads
x86/microcode: Get rid of struct apply_microcode_ctx
x86/spectre_v2: Don't check microcode versions when running under hypervisors
x86/vsyscall/64: Drop "native" vsyscalls
x86/entry/64/compat: Save one instruction in entry_INT80_compat()
x86/entry: Do not special-case clone(2) in compat entry
x86/syscalls: Use COMPAT_SYSCALL_DEFINEx() macros for x86-only compat syscalls
x86/syscalls: Use proper syscall definition for sys_ioperm()
x86/entry: Remove stale syscall prototype
x86/syscalls/32: Simplify $entry == $compat entries
objtool: Fix 32-bit build
Pull RCU updates from Paul E. McKenney:
- Miscellaneous fixes, perhaps most notably removing obsolete
code whose only purpose in life was to gather information for
the now-removed RCU debugfs facility. Other notable changes
include removing NO_HZ_FULL_ALL in favor of the nohz_full kernel
boot parameter, minor optimizations for expedited grace periods,
some added tracing, creating an RCU-specific workqueue using Tejun's
new WQ_MEM_RECLAIM flag, and several cleanups to code and comments.
- SRCU cleanups and optimizations.
- Torture-test updates, perhaps most notably the adding of ARMv8
support, but also including numerous cleanups and usability fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix userfaultfd_hugetlb on hosts which have more than 64 cpus.
---------------------------
running userfaultfd_hugetlb
---------------------------
invalid MiB
Usage: <MiB> <bounces>
[FAIL]
Via userfaultfd.c we can know, hugetlb_size needs to meet hugetlb_size
>= nr_cpus * hugepage_size. hugepage_size is often 2M, so when host
cpus > 64, it requires more than 128M.
[zhijianx.li@intel.com: update changelog/comments and variable name]
Link: http://lkml.kernel.org/r/20180302024356.83359-1-zhijianx.li@intel.com
Link: http://lkml.kernel.org/r/20180303125027.81638-1-zhijianx.li@intel.com
Link: http://lkml.kernel.org/r/20180302024356.83359-1-zhijianx.li@intel.com
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: SeongJae Park <sj38.park@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One notable fix to properly advertise our support for a new firmware feature,
caused by two series conflicting semantically but not textually.
There's a new ioctl for the new ocxl driver, which is not a fix, but needed to
complete the userspace API and good to have before the driver is in a released
kernel.
Finally three minor selftest fixes, and a fix for intermittent build failures
for some obscure platforms, caused by a missing make dependency.
Thanks to:
Alastair D'Silva, Bharata B Rao, Guenter Roeck.
-----BEGIN PGP SIGNATURE-----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=ajRr
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One notable fix to properly advertise our support for a new firmware
feature, caused by two series conflicting semantically but not
textually.
There's a new ioctl for the new ocxl driver, which is not a fix, but
needed to complete the userspace API and good to have before the
driver is in a released kernel.
Finally three minor selftest fixes, and a fix for intermittent build
failures for some obscure platforms, caused by a missing make
dependency.
Thanks to: Alastair D'Silva, Bharata B Rao, Guenter Roeck"
* tag 'powerpc-4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Fix vector5 in ibm architecture vector table
ocxl: Document the OCXL_IOCTL_GET_METADATA IOCTL
ocxl: Add get_metadata IOCTL to share OCXL information to userspace
selftests/powerpc: Skip the subpage_prot tests if the syscall is unavailable
selftests/powerpc: Fix missing clean of pmu/lib.o
powerpc/boot: Fix random libfdt related build errors
selftests/powerpc: Skip tm-trap if transactional memory is not enabled
With option -P, the test script will pause just before
the post_suite functions are called. This allows the tester to
inspect the system before it is torn down.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing the commands in the test cases, substitute
the test id for $TESTID. This helps to make more flexible
tests. For example, the testid can be given as a command
line argument.
As an example, if we wish to save the test output to a file
named for the test case, we can write in the test case:
"cmdUnderTest": "some test command | tee -a $TESTID.out"
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We miss CONFIG_* fragments so test fib-onlink-tests.sh can do:
ip li add lisa type vrf table 1101
ip li add veth1 type veth peer name veth2
And the follow message occurs if it isn't enabled:
Configuring interfaces
RTNETLINK answers: Operation not supported
This enables for NET_NRF (and friends) and VETH so we can create a vrf
table and veth.
Fixes: 153e1b84f4 ("selftests: Add FIB onlink tests")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Linux v3.2, vsyscalls have been deprecated and slow. From v3.2
on, Linux had three vsyscall modes: "native", "emulate", and "none".
"emulate" is the default. All known user programs work correctly in
emulate mode, but vsyscalls turn into page faults and are emulated.
This is very slow. In "native" mode, the vsyscall page is easily
usable as an exploit gadget, but vsyscalls are a bit faster -- they
turn into normal syscalls. (This is in contrast to vDSO functions,
which can be much faster than syscalls.) In "none" mode, there are
no vsyscalls.
For all practical purposes, "native" was really just a chicken bit
in case something went wrong with the emulation. It's been over six
years, and nothing has gone wrong. Delete it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/519fee5268faea09ae550776ce969fa6e88668b0.1520449896.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix copy&paste error and pass proper flags.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the "ok" action test so it checks that packet that is okayed does not
continue to be processed by other rules. Fix error message as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One single test implemented so far: test_pmtu_vti6_exception
checks that the PMTU of a route exception, caused by a tunnel
exceeding the link layer MTU, is affected by administrative
changes of the tunnel MTU. Creation of the route exception is
checked too.
Requested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
execute the subprocess in netns using 'ip netns exec'
Fixes: cc30c93fa0 ("selftests/net: ignore background traffic in psock_fanout")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add top level TAP header echo, testname and separator line to make
the output consistent with the common run_tests target.
This change prevents nested TAP13 headers output from individual tests.
Nested TAP13 headers could cause problems for some parsers.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
When you load nfit_test you currently see the following error in dmesg:
nfit_test nfit_test.0: found a zero length table '0' parsing nfit
This happens because when we parse the nfit_test.0 table via
acpi_nfit_init(), we specify a size of nfit_test->nfit_size. For the first
pass through nfit_test.0 where (t->setup_hotplug == 0) this is the size of
the entire buffer we allocated, including space for the hot plug
structures, not the size that we've actually filled in.
Fix this by only trying to parse the size of the structures that we've
filled in.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It turns out that we were overrunning the 'nfit_buf' buffer in
nfit_test0_setup() in the (t->setup_hotplug == 1) case because we failed to
correctly account for all of the acpi_nfit_memory_map structures.
Fix the structure count which will increase the allocation size of
'nfit_buf' in nfit_test0_alloc(). Also add some WARN_ON()s to
nfit_test0_setup() and nfit_test1_setup() to catch future issues where the
size of the buffer doesn't match the amount of data we're writing.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In nfit_test0_setup() and nfit_test1_setup() we keep an 'offset' value
which we use to calculate where in our 'nfit_buf' we will place our next
structure. The handling of 'offset' and the calculation of the placement
of the next structure is a bit inconsistent, though. We don't update
'offset' after we insert each structure, sometimes causing us to update it
for multiple structures' sizes at once. When calculating the position of
the next structure we aren't always able to just use 'offset', but
sometimes have to add in other structure sizes as well.
Fix this by updating 'offset' after each structure insertion in a
consistent way, allowing us to always calculate the position of the next
structure to be inserted by just using 'nfit_buf + offset'.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Export KSFT_TAP_LEVEL and add TAP Header echo to the run_kselftest.sh
script from emit_tests target handling.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Introduce environment variable KSFT_TAP_LEVEL to avoid printing
nested TAP headers for each test. lib.mk run_tests target prints
TAP header before invoking the test program or test script. Tests
need a way to suppress TAP headers if it is already printed out.
This new environment variable adds a way for ksft_print_header()
print TAP header only when KSFT_TAP_LEVEL isn't set.
lib.mk run_tests and test program should print TAP header and set
KSFT_TAP_LEVEL to avoid a second TAP header to be printed.
selftests Makefile should export KSFT_TAP_LEVEL and add TAP Header
echo to the run_kselftest.sh script from emit_tests target handling.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Ion is designed to be a framework used by other clients who perform
operations on the buffer. Use the DRM vgem client as a simple consumer.
In conjunction with the dma-buf sync ioctls, this tests the full attach/map
path for the system heap.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
There's no need to print messages each time we alloc and free. Remove them.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
This kselftest fixes update has a fix for regression in memory-hotplug
install script that prevents the test from running on the target.
-----BEGIN PGP SIGNATURE-----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=QfKZ
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"A fix for regression in memory-hotplug install script that prevents
the test from running on the target"
* tag 'linux-kselftest-4.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: memory-hotplug: fix emit_tests regression
Pull networking fixes from David Miller:
1) Use an appropriate TSQ pacing shift in mac80211, from Toke
Høiland-Jørgensen.
2) Just like ipv4's ip_route_me_harder(), we have to use skb_to_full_sk
in ip6_route_me_harder, from Eric Dumazet.
3) Fix several shutdown races and similar other problems in l2tp, from
James Chapman.
4) Handle missing XDP flush properly in tuntap, for real this time.
From Jason Wang.
5) Out-of-bounds access in powerpc ebpf tailcalls, from Daniel
Borkmann.
6) Fix phy_resume() locking, from Andrew Lunn.
7) IFLA_MTU values are ignored on newlink for some tunnel types, fix
from Xin Long.
8) Revert F-RTO middle box workarounds, they only handle one dimension
of the problem. From Yuchung Cheng.
9) Fix socket refcounting in RDS, from Ka-Cheong Poon.
10) Don't allow ppp unit registration to an unregistered channel, from
Guillaume Nault.
11) Various hv_netvsc fixes from Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (98 commits)
hv_netvsc: propagate rx filters to VF
hv_netvsc: filter multicast/broadcast
hv_netvsc: defer queue selection to VF
hv_netvsc: use napi_schedule_irqoff
hv_netvsc: fix race in napi poll when rescheduling
hv_netvsc: cancel subchannel setup before halting device
hv_netvsc: fix error unwind handling if vmbus_open fails
hv_netvsc: only wake transmit queue if link is up
hv_netvsc: avoid retry on send during shutdown
virtio-net: re enable XDP_REDIRECT for mergeable buffer
ppp: prevent unregistered channels from connecting to PPP units
tc-testing: skbmod: fix match value of ethertype
mlxsw: spectrum_switchdev: Check success of FDB add operation
net: make skb_gso_*_seglen functions private
net: xfrm: use skb_gso_validate_network_len() to check gso sizes
net: sched: tbf: handle GSO_BY_FRAGS case in enqueue
net: rename skb_gso_validate_mtu -> skb_gso_validate_network_len
rds: Incorrect reference counting in TCP socket creation
net: ethtool: don't ignore return from driver get_fecparam method
vrf: check forwarding on the original netdevice when generating ICMP dest unreachable
...
For tests using veth interfaces, the test infrastructure can create
the netdevs if they do not exist. Arguably this is a preferred approach
since the tests require p$N and p$(N+1) to be pairs.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the tc action test is used only to test mirred redirect
action. This patch extends it for mirred mirror.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iproute2 print_skbmod() prints the configured ethertype using format 0x%X:
therefore, test 9aa8 systematically fails, because it configures action #4
using ethertype 0x0031, and expects 0x0031 when it reads it back. Changing
the expected value to 0x31 lets the test result 'not ok' become 'ok'.
tested with:
# ./tdc.py -e 9aa8
Test 9aa8: Get a single skbmod action from a list
All test results:
1..1
ok 1 9aa8 Get a single skbmod action from a list
Fixes: cf797ac49b ("tc-testing: Add test cases for police and skbmod")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes testns after test failure so that next test can
continue with clean ns
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a command line arg to suppress tap output. Handy in case
all the tap output is being supplied by the plugins.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 multipath test using L4 hashing. Created with inputs from
Ido Schimmel.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Extend bpftool to build up CFG information of eBPF programs and add an
option to dump this in DOT format such that this can later be used with
DOT graphic tools (xdot, graphviz, etc) to visualize it. Part of the
analysis performed is sub-program detection and basic-block partitioning,
from Jiong.
2) Multiple enhancements for bpftool's batch mode, more specifically the
parser now understands comments (#), continuation lines (\), and arguments
enclosed between quotes. Also, allow to read from stdin via '-' as input
file, all from Quentin.
3) Improve BPF kselftests by i) unifying the rlimit handling into a helper
that is then used by all tests, and ii) add support for testing tail calls
to test_verifier plus add tests covering all corner cases. The latter is
especially useful for testing JITs, from Daniel.
4) Remove x64 JIT's bpf_flush_icache() since flush_icache_range() is a noop
on x64, from Daniel.
5) Fix one more occasion in BPF samples where we do not detach the BPF program
from the cgroup after completion, from Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 16c513b134
("selftests: memory-hotplug: silence test command echo")
introduced regression in emit_tests and results in the following
failure when selftests are installed and run. Fix it.
Running tests in memory-hotplug
========================================
./run_kselftest.sh: line 121: @./mem-on-off-test.sh: No such file or
directory
selftests: memory-hotplug [FAIL]
Fixes: 16c513b134 (selftests: memory-hotplug: silence test command echo")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-28
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Add schedule points and reduce the number of loop iterations
the test_bpf kernel module is performing in order to not hog
the CPU for too long, from Eric.
2) Fix an out of bounds access in tail calls in the ppc64 BPF
JIT compiler, from Daniel.
3) Fix a crash on arm64 on unaligned BPF xadd operations that
could be triggered via interpreter and JIT, from Daniel.
Please not that once you merge net into net-next at some point, there
is a minor merge conflict in test_verifier.c since test cases had
been added at the end in both trees. Resolution is trivial: keep all
the test cases from both trees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a better description to the summary for multipath tests. e.g.,
INFO: Running IPv6 multipath tests
TEST: ECMP [PASS]
INFO: Expected ratio 1.00 Measured ratio 1.02
TEST: Weighted MP 2:1 [PASS]
INFO: Expected ratio 2.00 Measured ratio 2.02
TEST: Weighted MP 11:45 [PASS]
INFO: Expected ratio 4.09 Measured ratio 4.03
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Debian jessie ping can not handle IPv6 addresses so the command
fails. Use PING6 which is set to ping6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the packet stats have a difference of 0, the test output shows:
INFO: Expected ratio 2.00 Measured ratio
Runtime error (func=(main), adr=9): Divide by zero
(standard_in) 2: syntax error
(standard_in) 1: syntax error
./router_multipath.sh: line 187: test: : integer expression expected
TEST: Multipath [FAIL]
Too large discrepancy between expected and measured ratios
Handle the 0 and display a cleaner message:
INFO: Running IPv6 multipath tests
TEST: Multipath [FAIL]
Packet difference is 0
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Capabilities of tc command are irrelevant for router tests:
$ ./router.sh
SKIP: iproute2 too old, missing shared block support
Add a CHECK_TC flag and only check tc capabilities if set. Add flag to
tc_common.sh and have it sourced before lib.sh
Also, if the command lacks some feature the test should exit non-0.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subpage_prot syscall is only functional when the system is using
the Hash MMU. Since commit 5b2b807147 ("powerpc/mm: Invalidate
subpage_prot() system call on radix platforms") it returns ENOENT when
the Radix MMU is active. Currently this just makes the test fail.
Additionally the syscall is not available if the kernel is built with
4K pages, or if CONFIG_PPC_SUBPAGE_PROT=n, in which case it returns
ENOSYS because the syscall is missing entirely.
So check explicitly for ENOENT and ENOSYS and skip if we see either of
those.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull kselftest fixes from Shuah Khan:
"Fixes for various problems in test output, compile errors, and missing
configs"
* tag 'linux-kselftest-4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: vm: update .gitignore with new test
selftests: memory-hotplug: silence test command echo
selftests/futex: Fix line continuation in Makefile
selftests: memfd: add config fragment for fuse
selftests: pstore: Adding config fragment CONFIG_PSTORE_RAM=m
selftests/android: Fix line continuation in Makefile
selftest/vDSO: fix O=
selftests: sync: missing CFLAGS while compiling
Test shared block infrastructure. This is a basic test that shares TC
block in between 2 clsact qdiscs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests chains matching and goto chain action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add first part of actions tests. This patch only contains tests of gact
ok/drop/trap and mirred redirect egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add first part of flower tests. This patch only contains dst/src ip/mac
matching.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have one host generate 16K IPv6 echo requests with a random flow label
and check that they are distributed between both multipath links
according to the provided weights.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use different weights for the multipath route configured on the first
router and check that the different flows generated by the first host
are distributed according to the provided weights.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a topology with two hosts, each directly connected to a different
router. Both routers are connected using two links, enabling multipath
routing.
Test IPv4 and IPv6 ping using default MTU and large MTU.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure two hosts which are directly connected to the same router and
test IPv4 and IPv6 ping. Use a large MTU and check that ping is
unaffected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test cases for unknown unicast and unregistered multicast flooding.
For each traffic type, turn off flooding on one bridged port and inject
a packet of the specified type through the second bridged port. Make
sure the packet was not received by checking the ACL counters on the
other end. Later, turn on flooding and make sure the packet was
received.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send a packet with a specific destination MAC, make sure it was learned
on the ingress port and then aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial framework to test packet forwarding functionality. The tests
can run on actual devices using loop-backed cables or using veth pairs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tm-resched-dscr test links against pmu/lib.o, but we don't have a
rule to clean pmu/lib.o. This can lead to a build break if you build
for big endian and then little, or vice versa.
Fix it by making tm-resched-dscr depend on pmu/lib.c, causing the code
to be built directly in, meaning no .o is generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PF_RDS sockets pass up cookies for zerocopy completion as ancillary
data. Update msg_zerocopy to reap this information.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for optimized reception of zerocopy completion,
revert the Rx side changes introduced by Commit dfb8434b0a
("selftests/net: add zerocopy support for PF_RDS test case")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 153e1b84f4 ("selftests: Add FIB onlink tests")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the downsides of the test_bpf module was that since being
in kernel space, it couldn't test-run tail calls. Now that the
test_verifier has the ability to perform run-time tests, populate
the prog array so we actually jump into other BPF programs and
can check all corner cases. Most useful in combination with JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Unify memlock handling into bpf_rlimit.h and replace all occurences
in BPF kselftests with it.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which produces an error when make versions
prior to 4.x are used for building the tests.
$ make
make[1]: Entering directory `/[...]/linux/tools/testing/selftests/futex'
/bin/sh: -c: line 5: syntax error: unexpected end of file
make[1]: *** [all] Error 1
make[1]: Leaving directory `/[...]/linux/tools/testing/selftests/futex'
make: *** [all] Error 2
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Khalid reported that the kernel selftests are currently failing:
selftests: test_bpf.sh
========================================
test_bpf: [FAIL]
not ok 1..8 selftests: test_bpf.sh [FAIL]
He bisected it to 6ce711f275 ("idr: Make
1-based IDRs more efficient").
The root cause is doing a signed comparison in idr_alloc_u32() instead
of an unsigned comparison. I went looking for any similar problems and
found a couple (which would each result in the failure to warn in two
situations that aren't supposed to happen).
I knocked up a few test-cases to prove that I was right and added them
to the test-suite.
Reported-by: Khalid Aziz <khalid.aziz@oracle.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
This patch converts old type string formattings to new type string
formattings for adapting Linux Traffic Control (tc) unit testing suite
python3.
Linux Traffic Control (tc) unit testing suite's code quality improved is improved with this patch.
According to python documentation;
"The built-in string class provides the ability to do complex variable substitutions and
value formatting via the format() method described in PEP 3101. "
but the project was using old type formattings and new type string formattings together,
this patch's main purpose is converting all old types to new types.
Following files changed:
1. tools/testing/selftests/tc-testing/tdc.py
2. tools/testing/selftests/tc-testing/tdc_batch.py
Following PEP rules applied:
1. PEP8 - Code Styling
2. PEP3101 - Advanced Code Formatting
Signed-off-by: Batuhan Osman Taskaya <batuhanosmantaskaya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do a better job with error handling - in pre- and post-suite,
in pre- and post-case. Show a traceback for errors.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-02-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various improvements for BPF kselftests: i) skip unprivileged tests
when kernel.unprivileged_bpf_disabled sysctl knob is set, ii) count
the number of skipped tests from unprivileged, iii) when a test case
had an unexpected error then print the actual but also the unexpected
one for better comparison, from Joe.
2) Add a sample program for collecting CPU state statistics with regards
to how long the CPU resides in cstate and pstate levels. Based on
cpu_idle and cpu_frequency trace points, from Leo.
3) Various x64 BPF JIT optimizations to further shrink the generated
image size in order to make it more icache friendly. When tested on
the Cilium generated programs, image size reduced by approx 4-5% in
best case mainly due to how LLVM emits unsigned 32 bit constants,
from Daniel.
4) Improvements and fixes on the BPF sockmap sample programs: i) fix
the sockmap's Makefile to include nlattr.o for libbpf, ii) detach
the sock ops programs from the cgroup before exit, from Prashant.
5) Avoid including xdp.h in filter.h by just forward declaring the
struct xdp_rxq_info in filter.h, from Jesper.
6) Fix the BPF kselftests Makefile for cgroup_helpers.c by only declaring
it a dependency for test_dev_cgroup.c but not every other test case
where it is not needed, from Jesper.
7) Adjust rlimit RLIMIT_MEMLOCK for test_tcpbpf_user selftest since the
default is insufficient for creating the 'global_map' used in the
corresponding BPF program, from Yonghong.
8) Likewise, for the xdp_redirect sample, Tushar ran into the same when
invoking xdp_redirect and xdp_monitor at the same time, therefore
in order to have the sample generically work bump the limit here,
too. Fix from Tushar.
9) Avoid an unnecessary NULL check in BPF_CGROUP_RUN_PROG_INET_SOCK()
since sk is always guaranteed to be non-NULL, from Yafang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some processor revisions do not support transactional memory, and
additionally kernel support can be disabled. In either case the
tm-trap test should be skipped, otherwise it will fail with a SIGILL.
Fixes: a08082f8e4 ("powerpc/selftests: Check endianness on trap in TM")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Add an empty linux/compiler_types.h (now being included by kconfig.h)
- Add __GFP_ZERO
- Add kzalloc
- Test __GFP_DIRECT_RECLAIM instead of __GFP_NOWARN
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Add few test cases that check the rnu-time results under JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking fixes from David Miller:
1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.
2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.
3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.
4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.
5) Fix potential deadlocks in netfilter getsockopt() code paths, from
Paolo Abeni.
6) Netfilter stackpointer size checks really are needed to validate
user input, from Florian Westphal.
7) Missing timer init in x_tables, from Paolo Abeni.
8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.
9) When an ibmvnic device is brought down then back up again, it can be
sent queue entries from a previous session, handle this properly
instead of crashing. From Thomas Falcon.
10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.
11) When we are dumping filters in cls_api, the output SKB is empty, and
the filter we are dumping is too large for the space in the SKB, we
should return -EMSGSIZE like other netlink dump operations do.
Otherwise userland has no signal that is needs to increase the size
of its read buffer. From Roman Kapl.
12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.
13) Module refcount leak in netlink when a dump start fails, from Jason
Donenfeld.
14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
from Eric Dumazet.
15) Releasing bpf per-cpu arraymaps can take a long time, add a
condtional scheduling point. From Eric Dumazet.
16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
Daniel Borkmann.
17) Fix page leak in gianfar driver, from Andy Spencer.
18) Missed clearing of estimator scratch buffer, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net_sched: gen_estimator: fix broken estimators based on percpu stats
gianfar: simplify FCS handling and fix memory leak
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
macvlan: fix use-after-free in macvlan_common_newlink()
bpf, arm64: fix out of bounds access in tail call
bpf, x64: implement retpoline for tail call
rxrpc: Fix send in rxrpc_send_data_packet()
net: aquantia: Fix error handling in aq_pci_probe()
bpf: fix rcu lockdep warning for lpm_trie map_free callback
bpf: add schedule points in percpu arrays management
regulatory: add NUL to request alpha2
ibmvnic: Fix early release of login buffer
net/smc9194: Remove bogus CONFIG_MAC reference
net: ipv4: Set addr_type in hash_keys for forwarded case
tcp_bbr: better deal with suboptimal GSO
smsc75xx: fix smsc75xx_set_features()
netlink: put module reference if dump start fails
selftests/bpf/test_maps: exit child process without error in ENOMEM case
selftests/bpf: update gitignore with test_libbpf_open
selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
..
Pull security subsystem fixes from James Morris:
- keys fixes via David Howells:
"A collection of fixes for Linux keyrings, mostly thanks to Eric
Biggers:
- Fix some PKCS#7 verification issues.
- Fix handling of unsupported crypto in X.509.
- Fix too-large allocation in big_key"
- Seccomp updates via Kees Cook:
"These are fixes for the get_metadata interface that landed during
-rc1. While the new selftest is strictly not a bug fix, I think
it's in the same spirit of avoiding bugs"
- an IMA build fix from Randy Dunlap
* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
integrity/security: fix digsig.c build error with header file
KEYS: Use individual pages in big_key for crypto buffers
X.509: fix NULL dereference when restricting key with unsupported_sig
X.509: fix BUG_ON() when hash algorithm is unsupported
PKCS#7: fix direct verification of SignerInfo signature
PKCS#7: fix certificate blacklisting
PKCS#7: fix certificate chain verification
seccomp: add a selftest for get_metadata
ptrace, seccomp: tweak get_metadata behavior slightly
seccomp, ptrace: switch get_metadata types to arch independent
The requirements around atomic_add() / atomic64_add() resp. their
JIT implementations differ across architectures. E.g. while x86_64
seems just fine with BPF's xadd on unaligned memory, on arm64 it
triggers via interpreter but also JIT the following crash:
[ 830.864985] Unable to handle kernel paging request at virtual address ffff8097d7ed6703
[...]
[ 830.916161] Internal error: Oops: 96000021 [#1] SMP
[ 830.984755] CPU: 37 PID: 2788 Comm: test_verifier Not tainted 4.16.0-rc2+ #8
[ 830.991790] Hardware name: Huawei TaiShan 2280 /BC11SPCD, BIOS 1.29 07/17/2017
[ 830.998998] pstate: 80400005 (Nzcv daif +PAN -UAO)
[ 831.003793] pc : __ll_sc_atomic_add+0x4/0x18
[ 831.008055] lr : ___bpf_prog_run+0x1198/0x1588
[ 831.012485] sp : ffff00001ccabc20
[ 831.015786] x29: ffff00001ccabc20 x28: ffff8017d56a0f00
[ 831.021087] x27: 0000000000000001 x26: 0000000000000000
[ 831.026387] x25: 000000c168d9db98 x24: 0000000000000000
[ 831.031686] x23: ffff000008203878 x22: ffff000009488000
[ 831.036986] x21: ffff000008b14e28 x20: ffff00001ccabcb0
[ 831.042286] x19: ffff0000097b5080 x18: 0000000000000a03
[ 831.047585] x17: 0000000000000000 x16: 0000000000000000
[ 831.052885] x15: 0000ffffaeca8000 x14: 0000000000000000
[ 831.058184] x13: 0000000000000000 x12: 0000000000000000
[ 831.063484] x11: 0000000000000001 x10: 0000000000000000
[ 831.068783] x9 : 0000000000000000 x8 : 0000000000000000
[ 831.074083] x7 : 0000000000000000 x6 : 000580d428000000
[ 831.079383] x5 : 0000000000000018 x4 : 0000000000000000
[ 831.084682] x3 : ffff00001ccabcb0 x2 : 0000000000000001
[ 831.089982] x1 : ffff8097d7ed6703 x0 : 0000000000000001
[ 831.095282] Process test_verifier (pid: 2788, stack limit = 0x0000000018370044)
[ 831.102577] Call trace:
[ 831.105012] __ll_sc_atomic_add+0x4/0x18
[ 831.108923] __bpf_prog_run32+0x4c/0x70
[ 831.112748] bpf_test_run+0x78/0xf8
[ 831.116224] bpf_prog_test_run_xdp+0xb4/0x120
[ 831.120567] SyS_bpf+0x77c/0x1110
[ 831.123873] el0_svc_naked+0x30/0x34
[ 831.127437] Code: 97fffe97 17ffffec 00000000 f9800031 (885f7c31)
Reason for this is because memory is required to be aligned. In
case of BPF, we always enforce alignment in terms of stack access,
but not when accessing map values or packet data when the underlying
arch (e.g. arm64) has CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS set.
xadd on packet data that is local to us anyway is just wrong, so
forbid this case entirely. The only place where xadd makes sense in
fact are map values; xadd on stack is wrong as well, but it's been
around for much longer. Specifically enforce strict alignment in case
of xadd, so that we handle this case generically and avoid such crashes
in the first place.
Fixes: 17a5267067 ("bpf: verifier (add verifier core)")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The packet fanout test generates UDP traffic and reads this with
a pair of packet sockets, testing the various fanout algorithms.
Avoid non-determinism from reading unrelated background traffic.
Fanout decisions are made before unrelated packets can be dropped with
a filter, so that is an insufficient strategy [*]. Run the packet
socket tests in a network namespace, similar to msg_zerocopy.
It it still good practice to install a filter on a packet socket
before accepting traffic. Because this is example code, demonstrate
that pattern. Open the socket initially bound to no protocol, install
a filter, and only then bind to ETH_P_IP.
Another source of non-determinism is hash collisions in FANOUT_HASH.
The hash function used to select a socket in the fanout group includes
the pseudorandom number hashrnd, which is not visible from userspace.
To work around this, the test tries to find a pair of UDP source ports
that do not collide. It gives up too soon (5 times, every 32 runs) and
output is confusing. Increase tries to 20 and revise the error msg.
[*] another approach would be to add a third socket to the fanout
group and direct all unexpected traffic here. This is possible
only when reimplementing methods like RR or HASH alongside this
extra catch-all bucket, using the BPF fanout method.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I recently noticed a crash on arm64 when feeding a bogus index
into BPF tail call helper. The crash would not occur when the
interpreter is used, but only in case of JIT. Output looks as
follows:
[ 347.007486] Unable to handle kernel paging request at virtual address fffb850e96492510
[...]
[ 347.043065] [fffb850e96492510] address between user and kernel address ranges
[ 347.050205] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 347.190829] x13: 0000000000000000 x12: 0000000000000000
[ 347.196128] x11: fffc047ebe782800 x10: ffff808fd7d0fd10
[ 347.201427] x9 : 0000000000000000 x8 : 0000000000000000
[ 347.206726] x7 : 0000000000000000 x6 : 001c991738000000
[ 347.212025] x5 : 0000000000000018 x4 : 000000000000ba5a
[ 347.217325] x3 : 00000000000329c4 x2 : ffff808fd7cf0500
[ 347.222625] x1 : ffff808fd7d0fc00 x0 : ffff808fd7cf0500
[ 347.227926] Process test_verifier (pid: 4548, stack limit = 0x000000007467fa61)
[ 347.235221] Call trace:
[ 347.237656] 0xffff000002f3a4fc
[ 347.240784] bpf_test_run+0x78/0xf8
[ 347.244260] bpf_prog_test_run_skb+0x148/0x230
[ 347.248694] SyS_bpf+0x77c/0x1110
[ 347.251999] el0_svc_naked+0x30/0x34
[ 347.255564] Code: 9100075a d280220a 8b0a002a d37df04b (f86b694b)
[...]
In this case the index used in BPF r3 is the same as in r1
at the time of the call, meaning we fed a pointer as index;
here, it had the value 0xffff808fd7cf0500 which sits in x2.
While I found tail calls to be working in general (also for
hitting the error cases), I noticed the following in the code
emission:
# bpftool p d j i 988
[...]
38: ldr w10, [x1,x10]
3c: cmp w2, w10
40: b.ge 0x000000000000007c <-- signed cmp
44: mov x10, #0x20 // #32
48: cmp x26, x10
4c: b.gt 0x000000000000007c
50: add x26, x26, #0x1
54: mov x10, #0x110 // #272
58: add x10, x1, x10
5c: lsl x11, x2, #3
60: ldr x11, [x10,x11] <-- faulting insn (f86b694b)
64: cbz x11, 0x000000000000007c
[...]
Meaning, the tests passed because commit ddb55992b0 ("arm64:
bpf: implement bpf_tail_call() helper") was using signed compares
instead of unsigned which as a result had the test wrongly passing.
Change this but also the tail call count test both into unsigned
and cap the index as u32. Latter we did as well in 90caccdd8c
("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here,
too. Tested on HiSilicon Hi1616.
Result after patch:
# bpftool p d j i 268
[...]
38: ldr w10, [x1,x10]
3c: add w2, w2, #0x0
40: cmp w2, w10
44: b.cs 0x0000000000000080
48: mov x10, #0x20 // #32
4c: cmp x26, x10
50: b.hi 0x0000000000000080
54: add x26, x26, #0x1
58: mov x10, #0x110 // #272
5c: add x10, x1, x10
60: lsl x11, x2, #3
64: ldr x11, [x10,x11]
68: cbz x11, 0x0000000000000080
[...]
Fixes: ddb55992b0 ("arm64: bpf: implement bpf_tail_call() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
test_maps contains a series of stress tests, and previously it will break the
rest tests when it failed to alloc memory.
-----------------------
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=16 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
test_maps: test_maps.c:955: run_parallel: Assertion `status == 0' failed.
Aborted
not ok 1..3 selftests: test_maps [FAIL]
-----------------------
after this patch, the rest tests will be continue when it occurs an ENOMEM failure
CC: Alexei Starovoitov <alexei.starovoitov@gmail.com>
CC: Philip Li <philip.li@intel.com>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Let's test that we get the flags correctly, and that we preserve the filter
index across the ptrace(PTRACE_SECCOMP_GET_METADATA) correctly.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
bpf builds a test program for loading BPF ELF files. Add the executable
to the .gitignore list.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Both glibc and the kernel have in6_* macros definitions. Build fails
because it picks up wrong in6_* macro from the kernel header and not the
header from glibc.
Fixes build error below:
clang -I. -I./include/uapi -I../../../include/uapi
-Wno-compare-distinct-pointer-types \
-O2 -target bpf -emit-llvm -c test_tcpbpf_kern.c -o - | \
llc -march=bpf -mcpu=generic -filetype=obj
-o .../tools/testing/selftests/bpf/test_tcpbpf_kern.o
In file included from test_tcpbpf_kern.c:12:
.../netinet/in.h:101:5: error: expected identifier
IPPROTO_HOPOPTS = 0, /* IPv6 Hop-by-Hop options. */
^
.../linux/in6.h:131:26: note: expanded from macro 'IPPROTO_HOPOPTS'
^
In file included from test_tcpbpf_kern.c:12:
/usr/include/netinet/in.h:103:5: error: expected identifier
IPPROTO_ROUTING = 43, /* IPv6 routing header. */
^
.../linux/in6.h:132:26: note: expanded from macro 'IPPROTO_ROUTING'
^
In file included from test_tcpbpf_kern.c:12:
.../netinet/in.h:105:5: error: expected identifier
IPPROTO_FRAGMENT = 44, /* IPv6 fragmentation header. */
^
Since both glibc and the kernel have in6_* macros definitions, use the
one from glibc. Kernel headers will check for previous libc definitions
by including include/linux/libc-compat.h.
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
While testing memfd tests, there is a missing script, as reported by
kselftest:
./run_tests.sh: line 7: ./run_fuse_test.sh: No such file or directory
Link: http://lkml.kernel.org/r/1517955779-11386-1-git-send-email-daniel.diaz@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default values for nreader and nwriter are apparently not all that
user-friendly, resulting in people doing scalability tests that ran all
runs at large scale. This commit therefore makes both the nreaders and
nwriters module default to the number of CPUs, and adds a comment to
rcuperf.c stating that the number of CPUs should be specified using the
nr_cpus kernel boot parameter. This commit also eliminates the redundant
rcuperf scripting specification of default values for these parameters.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcuperf trace-event processing counted every "done" trace event
as a piggyback, which is incorrect because the task that started the
grace period didn't piggyback at all. This commit fixes this problem
by recording the task that started a given grace period and ignoring
that task's "done" record for that grace period.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcuperf event-trace processing assumes that expedited grace periods
start and end on the same task, an assumption that was violated by moving
expedited grace-period processing to workqueues. This commit removes
this now-fallacious assumption from rcuperf's event-trace processing.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The purpose of jitter is to expose concurrency bugs due to invalid
assumptions about forward progress. There is usually little point
in jitter when measuring performance. This commit therefore defaults
jitter off when running rcuperf. You can override this by specifying
the kvm.sh "--jitter" argument -after- the "--torture rcuperf"
argument. No idea why you would want this, but if you do, that is
how you do it.
One example of a conccurrency bug that this jitter might expose is one
in which the developer assumed that a given short region of code would be
guaranteed to execute within some short time limit. Such assumptions are
invalid in virtualized environments because the hupervisor can preempt
the guest OS at any point, even when the guest OS thinks that it has
disabled interrupts.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The 512 megabyte memory size has served quite well, but more memory
is required when using large trace buffers on large systems. This
commit therefore adds a --memory argument to the kvm.sh script, which
allows the memory size to be specified on the command line, for example,
"--memory 768", --memory 800M", or "--memory 2G".
Reported-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds support of the qemu command qemu-system-aarch64
to rcutorture.
Signed-off-by: Lihao Liang <lianglihao@huawei.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The kvm.sh header comment is a bit of a relic, so this commit brings
it up to date.
Reported-by: Lihao Liang <lianglihao@huawei.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Send a cookie with sendmsg() on PF_RDS sockets, and process the
returned batched cookies in do_recv_completion()
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for basic PF_RDS client-server testing in msg_zerocopy
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6f1982fedd ("sched/isolation: Handle the nohz_full= parameter")
broke CONFIG_NO_HZ_FULL_ALL=y kernels. This breakage is due to the code
under CONFIG_NO_HZ_FULL_ALL failing to invoke the shiny new housekeeping
functions. This means that rcutorture scenario TREE04 now emits RCU CPU
stall warnings due to the RCU grace-period kthreads not being awakened
at a time of their choosing, or perhaps even not at all:
[ 27.731422] rcu_bh kthread starved for 21001 jiffies! g18446744073709551369 c18446744073709551368 f0x0 RCU_GP_WAIT_FQS(3) ->state=0x402 ->cpu=3
[ 27.731423] rcu_bh I14936 9 2 0x80080000
[ 27.731435] Call Trace:
[ 27.731440] __schedule+0x31a/0x6d0
[ 27.731442] schedule+0x31/0x80
[ 27.731446] schedule_timeout+0x15a/0x320
[ 27.731453] ? call_timer_fn+0x130/0x130
[ 27.731457] rcu_gp_kthread+0x66c/0xea0
[ 27.731458] ? rcu_gp_kthread+0x66c/0xea0
Because no one has complained about CONFIG_NO_HZ_FULL_ALL=y being broken,
I hypothesize that no one is in fact using it, other than rcutorture.
This commit therefore eliminates CONFIG_NO_HZ_FULL_ALL and updates
rcutorture's config files to instead use the nohz_full= kernel parameter
to put the desired CPUs into nohz_full mode.
Fixes: 6f1982fedd ("sched/isolation: Handle the nohz_full= parameter")
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
eBPF test fails due to verifier failure because log_buf is too small.
Fixed by increasing log_buf size
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run the command under test under valgrind. Produce an extra set of
tap output for the memory check on each test.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the functionality of creating a namespace before the test suite
and destroying it afterwards to a plugin.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the functionality that checks for root permissions into a plugin.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be a general test architecture, and yet allow specific
tests to be done. Introduce a plugin architecture.
An individual test has 4 stages, setup/execute/verify/teardown. Each
plugin gets a chance to run a function at each stage, plus one call
before all the tests are called ("pre" suite) and one after all the
tests are called ("post" suite). In addition, just before each
command is executed, the plugin gets a chance to modify the command
using the "adjust_command" hook. This makes the test suite quite
flexible.
Future patches will take some functionality out of the tdc.py script and
place it in plugins.
To use the plugins, place the implementation in the plugins directory
and run tdc.py. It will notice the plugins and use them.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the test_runner function into the loop part (test_runner)
and the contents (run_one_test) for maintainability.
It makes it a little easier to catch exceptions
in an individual test, and keep going (and flush a bunch
of tap results for the skipped tests).
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the functionality of the command line parameters into "selection"
parameters, "action" parameters and other parameters.
"Selection" parameters are for choosing which tests on which to act.
"Action" parameters are for choosing what to do with the selected tests.
"Other" parameters are for global effect (like "help" or "verbose").
With this commit, we add the ability to name a directory as another
selection mechanism. We can accumulate a number of tests by directory,
file, category, or even by test id, instead of being constrained to
run all tests in one collection or just one test.
Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Acked-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "kernel.unprivileged_bpf_disabled" sysctl, if enabled, causes all
unprivileged tests to fail because it permanently disables unprivileged
BPF access for the currently running kernel. Skip the relevant tests if
the user attempts to run the testsuite with this sysctl enabled.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When priviliged tests are skipped due to user rights, count the number of
skipped tests so it's more obvious that the test did not check everything.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This makes it easier to debug off-hand when the error message isn't
exactly as expected.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull x86 PTI and Spectre related fixes and updates from Ingo Molnar:
"Here's the latest set of Spectre and PTI related fixes and updates:
Spectre:
- Add entry code register clearing to reduce the Spectre attack
surface
- Update the Spectre microcode blacklist
- Inline the KVM Spectre helpers to get close to v4.14 performance
again.
- Fix indirect_branch_prediction_barrier()
- Fix/improve Spectre related kernel messages
- Fix array_index_nospec_mask() asm constraint
- KVM: fix two MSR handling bugs
PTI:
- Fix a paranoid entry PTI CR3 handling bug
- Fix comments
objtool:
- Fix paranoid_entry() frame pointer warning
- Annotate WARN()-related UD2 as reachable
- Various fixes
- Add Add Peter Zijlstra as objtool co-maintainer
Misc:
- Various x86 entry code self-test fixes
- Improve/simplify entry code stack frame generation and handling
after recent heavy-handed PTI and Spectre changes. (There's two
more WIP improvements expected here.)
- Type fix for cache entries
There's also some low risk non-fix changes I've included in this
branch to reduce backporting conflicts:
- rename a confusing x86_cpu field name
- de-obfuscate the naming of single-TLB flushing primitives"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
x86/entry/64: Fix CR3 restore in paranoid_exit()
x86/cpu: Change type of x86_cache_size variable to unsigned int
x86/spectre: Fix an error message
x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_stepping
selftests/x86/mpx: Fix incorrect bounds with old _sigfault
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
x86/speculation: Add <asm/msr-index.h> dependency
nospec: Move array_index_nospec() parameter checking into separate macro
x86/speculation: Fix up array_index_nospec_mask() asm constraint
x86/debug: Use UD2 for WARN()
x86/debug, objtool: Annotate WARN()-related UD2 as reachable
objtool: Fix segfault in ignore_unreachable_insn()
selftests/x86: Disable tests requiring 32-bit support on pure 64-bit systems
selftests/x86: Do not rely on "int $0x80" in single_step_syscall.c
selftests/x86: Do not rely on "int $0x80" in test_mremap_vdso.c
selftests/x86: Fix build bug caused by the 5lvl test which has been moved to the VM directory
selftests/x86/pkeys: Remove unused functions
selftests/x86: Clean up and document sscanf() usage
selftests/x86: Fix vDSO selftest segfault for vsyscall=none
x86/entry/64: Remove the unused 'icebp' macro
...
For distributions with old userspace header files, the _sigfault
structure is different. mpx-mini-test fails with the following
error:
[root@Purley]# mpx-mini-test_64 tabletest
XSAVE is supported by HW & OS
XSAVE processor supported state mask: 0x2ff
XSAVE OS supported state mask: 0x2ff
BNDREGS: size: 64 user: 1 supervisor: 0 aligned: 0
BNDCSR: size: 64 user: 1 supervisor: 0 aligned: 0
starting mpx bounds table test
ERROR: siginfo bounds do not match shadow bounds for register 0
Fix it by using the correct offset of _lower/_upper in _sigfault.
RHEL needs this patch to work.
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave.hansen@linux.intel.com
Fixes: e754aedc26 ("x86/mpx, selftests: Add MPX self test")
Link: http://lkml.kernel.org/r/1513586050-1641-1-git-send-email-rui.y.wang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ldt_gdt and ptrace_syscall selftests, even in their 64-bit variant, use
hard-coded 32-bit syscall numbers and call "int $0x80".
This will fail on 64-bit systems with CONFIG_IA32_EMULATION=y disabled.
Therefore, do not build these tests if we cannot build 32-bit binaries
(which should be a good approximation for CONFIG_IA32_EMULATION=y being enabled).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211111013.16888-6-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On 64-bit builds, we should not rely on "int $0x80" working (it only does if
CONFIG_IA32_EMULATION=y is enabled). To keep the "Set TF and check int80"
test running on 64-bit installs with CONFIG_IA32_EMULATION=y enabled, build
this test only if we can also build 32-bit binaries (which should be a
good approximation for that).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211111013.16888-5-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A larger batch of fixes than we'd like. Roughly 1/3 fixes for new code, 1/3
fixes for stable and 1/3 minor things.
There's four commits fixing bugs when using 16GB huge pages on hash, caused by
some of the preparatory changes for pkeys.
Two fixes for bugs in the enhanced IRQ soft masking for local_t, one of which
broke KVM in some circumstances.
Four fixes for Power9. The most bizarre being a bug where futexes stopped
working because a NULL pointer dereference didn't trap during early boot (it
aliased the kernel mapping). A fix for memory hotplug when using the Radix MMU,
and a fix for live migration of guests using the Radix MMU.
Two fixes for hotplug on pseries machines. One where we weren't correctly
updating NUMA info when CPUs are added and removed. And the other fixes
crashes/hangs seen when doing memory hot remove during boot, which is apparently
a thing people do.
Finally a handful of build fixes for obscure configs and other minor fixes.
Thanks to:
Alexey Kardashevskiy, Aneesh Kumar K.V, Balbir Singh, Colin Ian King, Daniel
Henrique Barboza, Florian Weimer, Guenter Roeck, Harish, Laurent Vivier,
Madhavan Srinivasan, Mauricio Faria de Oliveira, Nathan Fontenot, Nicholas
Piggin, Sam Bobroff.
-----BEGIN PGP SIGNATURE-----
iQIwBAABCAAaBQJahDTmExxtcGVAZWxsZXJtYW4uaWQuYXUACgkQUevqPMjhpYAd
chAAtVe8hmkEJefTbU63GBeqva0JHSiTu2DENZAlN/epWtbtyl05PLETMdTcwGCv
nK2zzR+xbSFN1DzZK8KQfDBW33McKZE+YkHwYOC8Kff/N0SKdHK4zvxYr7FTZGzG
9uSG5vrxVEsPLT/yANabl0d0vKWMsJ1jZquvJAU0eLNUbA/skGjEPADtXqYQUXiA
EnW4xeczsMLjuzTleoRqrBx74Gulovuq9LVAjfDvkydWlCU9MQkrodCgP0V2hQtw
RAJ/QLY+NS/vMCBnvVOGBaKzIqrfeQTHF3P0j4pyBeBq/2kNuidM5n25uoc31wUq
DE4Ebe2FJA6CHP5KEyf7dr9y7gsks/ak3/CKs+l6Yz3/0BqenEMhu6WKJ1tgf9cC
qAmi1dIjtpw6JZ6baCbkloUdAGNjKVfLWB9ld9VIfg0C+C3y4L7+TKJukxrCBGI6
hopfT/3p8xUdla3euiRXRLZzajyKDGrqk71hk5J/J0ChXfWB0B51X0F6NIfH41Mn
YsVUQ95p3zS79Pl942ijGScFX/bNVLfEEGzlI/nwU/wbTxF5g/XNXm5PjBsGSr/W
zFcCwCpFV2b/kypQoxQA5CbrKRCLOleDA/lLOxW/1NMYOQsNj05DM9wYAw5Bl+lX
AVj2c5jM9heNN4scxDiufRNfqZbyjZ4fFUpXLNqs7N5vcks=
=BmuL
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A larger batch of fixes than we'd like. Roughly 1/3 fixes for new
code, 1/3 fixes for stable and 1/3 minor things.
There's four commits fixing bugs when using 16GB huge pages on hash,
caused by some of the preparatory changes for pkeys.
Two fixes for bugs in the enhanced IRQ soft masking for local_t, one
of which broke KVM in some circumstances.
Four fixes for Power9. The most bizarre being a bug where futexes
stopped working because a NULL pointer dereference didn't trap during
early boot (it aliased the kernel mapping). A fix for memory hotplug
when using the Radix MMU, and a fix for live migration of guests using
the Radix MMU.
Two fixes for hotplug on pseries machines. One where we weren't
correctly updating NUMA info when CPUs are added and removed. And the
other fixes crashes/hangs seen when doing memory hot remove during
boot, which is apparently a thing people do.
Finally a handful of build fixes for obscure configs and other minor
fixes.
Thanks to: Alexey Kardashevskiy, Aneesh Kumar K.V, Balbir Singh, Colin
Ian King, Daniel Henrique Barboza, Florian Weimer, Guenter Roeck,
Harish, Laurent Vivier, Madhavan Srinivasan, Mauricio Faria de
Oliveira, Nathan Fontenot, Nicholas Piggin, Sam Bobroff"
* tag 'powerpc-4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix to use ucontext_t instead of struct ucontext
powerpc/kdump: Fix powernv build break when KEXEC_CORE=n
powerpc/pseries: Fix build break for SPLPAR=n and CPU hotplug
powerpc/mm/hash64: Zero PGD pages on allocation
powerpc/mm/hash64: Store the slot information at the right offset for hugetlb
powerpc/mm/hash64: Allocate larger PMD table if hugetlb config is enabled
powerpc/mm: Fix crashes with 16G huge pages
powerpc/mm: Flush radix process translations when setting MMU type
powerpc/vas: Don't set uses_vas for kernel windows
powerpc/pseries: Enable RAS hotplug events later
powerpc/mm/radix: Split linear mapping on hot-unplug
powerpc/64s/radix: Boot-time NULL pointer protection using a guard-PID
ocxl: fix signed comparison with less than zero
powerpc/64s: Fix may_hard_irq_enable() for PMI soft masking
powerpc/64s: Fix MASKABLE_RELON_EXCEPTION_HV_OOL macro
powerpc/numa: Invalidate numa_cpu_lookup_table on cpu remove
The default rlimit RLIMIT_MEMLOCK is 64KB. In certain cases,
e.g. in a test machine mimicking our production system, this test may
fail due to unable to charge the required memory for map creation:
# ./test_tcpbpf_user
libbpf: failed to create map (name: 'global_map'): Operation not permitted
libbpf: failed to load object 'test_tcpbpf_kern.o'
FAILED: load_bpf_file failed for: test_tcpbpf_kern.o
Changing the default rlimit RLIMIT_MEMLOCK to unlimited makes
the test always pass.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The current selftests Makefile construct result in cgroup_helpers.c
gets compiled together with all the TEST_GEN_PROGS. And it also result
in invoking the libbpf Makefile two times (tools/lib/bpf).
These issues were introduced in commit 9d1f159419 ("bpf: move
cgroup_helpers from samples/bpf/ to tools/testing/selftesting/bpf/").
The only test program that requires the cgroup helpers is 'test_dev_cgroup'.
Thus, create a make target $(OUTPUT)/test_dev_cgroup that extend[1]
the 'prerequisite' for the 'stem' %-style pattern in ../lib.mk,
for this particular test program.
Reviewers notice the make-rules in tools/testing/selftests/lib.mk
differ from the normal kernel kbuild rules, and it is practical
to use 'make -p' to follow how these 'Implicit/static pattern stem'
gets expanded.
[1] https://www.gnu.org/software/make/manual/html_node/Static-Usage.html
Fixes: 9d1f159419 ("bpf: move cgroup_helpers from samples/bpf/ to tools/testing/selftesting/bpf/")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The memfd test requires to insert the fuse module (CONFIG_FUSE_FS).
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which can make the subsequent rsync
command go awry over the whole filesystem (`rsync -a / /`).
/bin/sh: -c: line 5: syntax error: unexpected end of file
make[1]: [all] Error 1 (ignored)
TEST=$DIR"_test.sh"; \
if [ -e $DIR/$TEST ]; then
/bin/sh: -c: line 2: syntax error: unexpected end of file
make[1]: [all] Error 1 (ignored)
rsync -a $DIR/$TEST $BUILD_TARGET/;
[...a myriad of:]
[ rsync: readlink_stat("...") failed: Permission denied (13)]
[ skipping non-regular file "..."]
[ rsync: opendir "..." failed: Permission denied (13)]
[and many other errors...]
fi
make[1]: fi: Command not found
make[1]: [all] Error 127 (ignored)
done
make[1]: done: Command not found
make[1]: [all] Error 127 (ignored)
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Acked-by: Pintu Agarwal <pintu.ping@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Add test cases verifying FIB onlink commands work as expected in
various conditions - IPv4, IPv6, main table, and VRF.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sleep for a second after setting carrier down to allow linkwatch
to propagate the change to the routing stack via netdev_state_change.
As it stands there is a race setting carrier down on the dummy
device and then checking the linkdown flag in the routes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setup and teardown of testns and dummy0 to helpers.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_tests.sh is failing in a VM:
$ fib_tests.sh
Running netdev unregister tests
PASS: unicast route test
PASS: multipath route test
Running netdev down tests
PASS: unicast route test
PASS: multipath route test
Running netdev carrier change tests
PASS: local route carrier test
FAIL: unicast route carrier test
The last test corresponds to fib_carrier_unicast_test which 12 places
that could be failing. Be more verbose in the output so a failure is
easier to track down and separate test setup failures with set -e and
set +e pairs.
With the verbose logging it is easier to see which checks are failing:
$fib_tests.sh
Single path route carrier test
....
Carrier down
IPv4 fibmatch [ OK ]
IPv6 fibmatch [ OK ]
IPv4 linkdown flag set [FAIL]
IPv6 linkdown flag set [FAIL]
Second address added with carrier down
IPv4 fibmatch [ OK ]
IPv6 fibmatch [ OK ]
IPv4 linkdown flag set [FAIL]
IPv6 linkdown flag set [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ip netns exec testns ip' is more efficiently handled using 'ip -netns';
runs the ip command after switching the namespace and avoids an exec.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vDSO selftests ignored the O= or KBUILD_OUTPUT= parameters. Fix it.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Based on patch: https://patchwork.kernel.org/patch/10042045/
arch64-linux-gnu-gcc -c sync.c -o sync/sync.o
sync.c:42:29: fatal error: linux/sync_file.h: No such file or directory
#include <linux/sync_file.h>
^
CFLAGS is not used during the compile step, so the system instead of
kernel headers are used. Fix this by adding CFLAGS to the OBJS compile
rule.
Reported-by: Lei Yang <Lei.Yang@windriver.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
With glibc 2.26 'struct ucontext' is removed to improve POSIX
compliance, which breaks powerpc/alignment_handler selftest. Fix the
test by using ucontext_t. Tested on ppc, works with older glibc
versions as well.
Fixes the following:
alignment_handler.c: In function ‘sighandler’:
alignment_handler.c:68:5: error: dereferencing pointer to incomplete type ‘struct ucontext’
ucp->uc_mcontext.gp_regs[PT_NIP] += 4;
Signed-off-by: Harish <harish@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 64-bit builds, we should not rely on "int $0x80" working (it only does if
CONFIG_IA32_EMULATION=y is enabled).
Without this patch, the move test may succeed, but the "int $0x80" causes
a segfault, resulting in a false negative output of this self-test.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211111013.16888-4-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This also gets rid of two build warnings:
protection_keys.c: In function ‘dumpit’:
protection_keys.c:419:3: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result [-Wunused-result]
write(1, buf, nr_read);
^~~~~~~~~~~~~~~~~~~~~~
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace a couple of magically connected buffer length literal constants with
a common definition that makes their relationship obvious. Also document
why our sscanf() usage is safe.
No intended functional changes.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211205924.GA23210@light.dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The vDSO selftest tries to execute a vsyscall unconditionally, even if it
is not present on the test system (e.g. if booted with vsyscall=none or
with CONFIG_LEGACY_VSYSCALL_NONE=y set. Fix this by copying (and tweaking)
the vsyscall check from test_vsyscall.c
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kselftest@vger.kernel.org
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180211111013.16888-3-linux@dominikbrodowski.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
as well as the removing of function probes.
This fixes the code with Al's suggestions. I also added a few selftests
to test the broken cases such that they wont happen again.
-----BEGIN PGP SIGNATURE-----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=tVDz
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Al Viro discovered some breakage with the parsing of the
set_ftrace_filter as well as the removing of function probes.
This fixes the code with Al's suggestions. I also added a few
selftests to test the broken cases such that they wont happen
again"
* tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Add more tests for removing of function probes
selftests/ftrace: Add some missing glob checks
selftests/ftrace: Have reset_ftrace_filter handle multiple instances
selftests/ftrace: Have reset_ftrace_filter handle modules
tracing: Fix parsing of globs with a wildcard at the beginning
ftrace: Remove incorrect setting of glob search field
Fix two issues in the reuseport_bpf selftests that were
reported by Linaro CI:
[...]
+ ./reuseport_bpf
---- IPv4 UDP ----
Testing EBPF mod 10...
Reprograming, testing mod 5...
./reuseport_bpf: ebpf error. log:
0: (bf) r6 = r1
1: (20) r0 = *(u32 *)skb[0]
2: (97) r0 %= 10
3: (95) exit
processed 4 insns
: Operation not permitted
+ echo FAIL
[...]
---- IPv4 TCP ----
Testing EBPF mod 10...
./reuseport_bpf: failed to bind send socket: Address already in use
+ echo FAIL
[...]
For the former adjust rlimit since this was the cause of
failure for loading the BPF prog, and for the latter add
SO_REUSEADDR.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3502
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This script test_libbpf.sh will be part of the 'make run_tests'
invocation, but can also be invoked manually in this directory,
and a verbose mode can be enabled via setting the environment
variable $VERBOSE like:
$ VERBOSE=yes ./test_libbpf.sh
The script contains some tests that are commented out, as they
currently fail. They are reminders about what we need to improve
for the libbpf loader library.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
V2: Moved program into selftests/bpf from tools/libbpf
This program can be used on its own for testing/debugging if a
BPF ELF-object file can be loaded with libbpf (from tools/lib/bpf).
If something is wrong with the ELF object, the program have
a --debug mode that will display the ELF sections and especially
the skipped sections. This allows for quickly identifying the
problematic ELF section number, which can be corrolated with the
readelf tool.
The program signal error via return codes, and also have
a --quiet mode, which is practical for use in scripts like
selftests/bpf.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull idr updates from Matthew Wilcox:
- test-suite improvements
- replace the extended API by improving the normal API
- performance improvement for IDRs which are 1-based rather than
0-based
- add documentation
* 'idr-2018-02-06' of git://git.infradead.org/users/willy/linux-dax:
idr: Add documentation
idr: Make 1-based IDRs more efficient
idr: Warn if old iterators see large IDs
idr: Rename idr_for_each_entry_ext
idr: Remove idr_alloc_ext
cls_u32: Convert to idr_alloc_u32
cls_u32: Reinstate cyclic allocation
cls_flower: Convert to idr_alloc_u32
cls_bpf: Convert to use idr_alloc_u32
cls_basic: Convert to use idr_alloc_u32
cls_api: Convert to idr_alloc_u32
net sched actions: Convert to use idr_alloc_u32
idr: Add idr_alloc_u32 helper
idr: Delete idr_find_ext function
idr: Delete idr_replace_ext function
idr: Delete idr_remove_ext function
IDR test suite: Check handling negative end correctly
idr test suite: Fix ida_test_random()
radix tree test suite: Remove ARRAY_SIZE
Al Viro discovered a bug in the removing of function probes where if it had
a '*' at the beginning, it would fail to find any matches. That is, because
it reset the glob search string to the the initial string with a "MATCH_END"
type, instead of skipping the wildcard "*" it included it, where it would
not match any functions because "*" was being treated as a normal character
and not a wildcard one.
Link: http://lkml.kernel.org/r/20180127031706.GE13338@ZenIV.linux.org.uk
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Al Viro discovered a bug in the glob ftrace filtering code where "*a*b" is
treated the same as "a*b", and functions that would be selected by "*a*b"
but not "a*b" are not selected with "*a*b".
Add tests for patterns "*a*b" and "a*b*" to the glob selftest.
Link: http://lkml.kernel.org/r/20180127170748.GF13338@ZenIV.linux.org.uk
Cc: Shuah Khan <shuah@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If a probe is attached to a static function that is in multiple files with
the same name, removing it by name will remove all instances:
# grep jump_label_unlock set_ftrace_filter
jump_label_unlock:traceoff:unlimited
jump_label_unlock:traceoff:unlimited
# echo '!jump_label_unlock:traceoff' >> set_ftrace_filter
# grep jump_label_unlock set_ftrace_filter
#
But the loop in reset_ftrace_filter will try to remove multiple instances
multiple times. If this happens the second time will error and cause the
test to fail.
At each iteration of the loop, check to see if the probe being removed still
exists.
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If a function probe in set_ftrace_filter belongs to a module, it will
contain the module name. Like:
wmi_query_block [wmi]:traceoff:unlimited
But writing:
'!wmi_query_block [wmi]:traceoff' > set_ftrace_filter
will cause an error. We still need to write:
'!wmi_query_block:traceoff' > set_ftrace_filter
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
test_kmod.sh reported false failure when module not present.
Check test_bpf.ko is present in the path before loading it.
Two cases to be addressed here,
In the development process of test_bpf.c unit testing will be done by
developers by using "insmod $SRC_TREE/lib/test_bpf.ko"
On the other hand testers run full tests by installing modules on device
under test (DUT) and followed by modprobe to insert the modules accordingly.
Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull scheduler updates from Ingo Molnar:
- membarrier updates (Mathieu Desnoyers)
- SMP balancing optimizations (Mel Gorman)
- stats update optimizations (Peter Zijlstra)
- RT scheduler race fixes (Steven Rostedt)
- misc fixes and updates
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Use a recently used CPU as an idle candidate and the basis for SIS
sched/fair: Do not migrate if the prev_cpu is idle
sched/fair: Restructure wake_affine*() to return a CPU id
sched/fair: Remove unnecessary parameters from wake_affine_idle()
sched/rt: Make update_curr_rt() more accurate
sched/rt: Up the root domain ref count when passing it around via IPIs
sched/rt: Use container_of() to get root domain in rto_push_irq_work_func()
sched/core: Optimize update_stats_*()
sched/core: Optimize ttwu_stat()
membarrier/selftest: Test private expedited sync core command
membarrier/arm64: Provide core serializing command
membarrier/x86: Provide core serializing command
membarrier: Provide core serializing command, *_SYNC_CORE
lockin/x86: Implement sync_core_before_usermode()
locking: Introduce sync_core_before_usermode()
membarrier/selftest: Test global expedited command
membarrier: Provide GLOBAL_EXPEDITED command
membarrier: Document scheduler barrier requirements
powerpc, membarrier: Skip memory barrier in switch_mm()
membarrier/selftest: Test private expedited command
Pull networking fixes from David Miller:
1) Fix error path in netdevsim, from Jakub Kicinski.
2) Default values listed in tcp_wmem and tcp_rmem documentation were
inaccurate, from Tonghao Zhang.
3) Fix route leaks in SCTP, both for ipv4 and ipv6. From Alexey Kodanev
and Tommi Rantala.
4) Fix "MASK < Y" meant to be "MASK << Y" in xgbe driver, from Wolfram
Sang.
5) Use after free in u32_destroy_key(), from Paolo Abeni.
6) Fix two TX issues in be2net driver, from Suredh Reddy.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
be2net: Handle transmit completion errors in Lancer
be2net: Fix HW stall issue in Lancer
RDS: IB: Fix null pointer issue
nfp: fix kdoc warnings on nested structures
sample/bpf: fix erspan metadata
net: erspan: fix erspan config overwrite
net: erspan: fix metadata extraction
cls_u32: fix use after free in u32_destroy_key()
net: amd-xgbe: fix comparison to bitshift when dealing with a mask
net: phy: Handle not having GPIO enabled in the kernel
ibmvnic: fix empty firmware version and errors cleanup
sctp: fix dst refcnt leak in sctp_v4_get_dst
sctp: fix dst refcnt leak in sctp_v6_get_dst()
dwc-xlgmac: remove Jie Deng as co-maintainer
doc: Change the min default value of tcp_wmem/tcp_rmem.
samples/bpf: use bpf_set_link_xdp_fd
libbpf: add missing SPDX-License-Identifier
libbpf: add error reporting in XDP
libbpf: add function to setup XDP
tools: add netlink.h and if_link.h in tools uapi
...
About 20% of the IDR users in the kernel want the allocated IDs to start
at 1. The implementation currently searches all the way down the left
hand side of the tree, finds no free ID other than ID 0, walks all the
way back up, and then all the way down again. This patch 'rebases' the
ID so we fill the entire radix tree, rather than leave a gap at 0.
Chris Wilson says: "I did the quick hack of allocating index 0 of the
idr and that eradicated idr_get_free() from being at the top of the
profiles for the many-object stress tests. This improvement will be
much appreciated."
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
It has no more users, so remove it. Move idr_alloc() back into idr.c,
move the guts of idr_alloc_cmn() into idr_alloc_u32(), remove the
wrappers around idr_get_free_cmn() and rename it to idr_get_free().
While there is now no interface to allocate IDs larger than a u32,
the IDR internals remain ready to handle a larger ID should a need arise.
These changes make it possible to provide the guarantee that, if the
nextid pointer points into the object, the object's ID will be initialised
before a concurrent lookup can find the object.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
One of the charming quirks of the idr_alloc() interface is that you
can pass a negative end and it will be interpreted as "maximum". Ensure
we don't break that.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
The test was checking the wrong errno; ida_get_new_above() returns
EAGAIN, not ENOMEM on memory allocation failure. Double the number of
threads to increase the chance that we actually exercise this path
during the test suite (it was a bit sporadic before).
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
* Require struct page by default for filesystem DAX to remove a number of
surprising failure cases. This includes failures with direct I/O, gdb and
fork(2).
* Add support for the new Platform Capabilities Structure added to the NFIT in
ACPI 6.2a. This new table tells us whether the platform supports flushing
of CPU and memory controller caches on unexpected power loss events.
* Revamp vmem_altmap and dev_pagemap handling to clean up code and better
support future future PCI P2P uses.
* Deprecate the ND_IOCTL_SMART_THRESHOLD command whose payload has become
out-of-sync with recent versions of the NVDIMM_FAMILY_INTEL spec, and
instead rely on the generic ND_CMD_CALL approach used by the two other IOCTL
families, NVDIMM_FAMILY_{HPE,MSFT}.
* Enhance nfit_test so we can test some of the new things added in version 1.6
of the DSM specification. This includes testing firmware download and
simulating the Last Shutdown State (LSS) status.
-----BEGIN PGP SIGNATURE-----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=MIMX
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Ross Zwisler:
- Require struct page by default for filesystem DAX to remove a number
of surprising failure cases. This includes failures with direct I/O,
gdb and fork(2).
- Add support for the new Platform Capabilities Structure added to the
NFIT in ACPI 6.2a. This new table tells us whether the platform
supports flushing of CPU and memory controller caches on unexpected
power loss events.
- Revamp vmem_altmap and dev_pagemap handling to clean up code and
better support future future PCI P2P uses.
- Deprecate the ND_IOCTL_SMART_THRESHOLD command whose payload has
become out-of-sync with recent versions of the NVDIMM_FAMILY_INTEL
spec, and instead rely on the generic ND_CMD_CALL approach used by
the two other IOCTL families, NVDIMM_FAMILY_{HPE,MSFT}.
- Enhance nfit_test so we can test some of the new things added in
version 1.6 of the DSM specification. This includes testing firmware
download and simulating the Last Shutdown State (LSS) status.
* tag 'libnvdimm-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (37 commits)
libnvdimm, namespace: remove redundant initialization of 'nd_mapping'
acpi, nfit: fix register dimm error handling
libnvdimm, namespace: make min namespace size 4K
tools/testing/nvdimm: force nfit_test to depend on instrumented modules
libnvdimm/nfit_test: adding support for unit testing enable LSS status
libnvdimm/nfit_test: add firmware download emulation
nfit-test: Add platform cap support from ACPI 6.2a to test
libnvdimm: expose platform persistence attribute for nd_region
acpi: nfit: add persistent memory control flag for nd_region
acpi: nfit: Add support for detect platform CPU cache flush on power loss
device-dax: Fix trailing semicolon
libnvdimm, btt: fix uninitialized err_lock
dax: require 'struct page' by default for filesystem dax
ext2: auto disable dax instead of failing mount
ext4: auto disable dax instead of failing mount
mm, dax: introduce pfn_t_special()
mm: Fix devm_memremap_pages() collision handling
mm: Fix memory size alignment in devm_memremap_pages_release()
memremap: merge find_dev_pagemap into get_dev_pagemap
memremap: change devm_memremap_pages interface to use struct dev_pagemap
...
The tests at tools/testing/selftests/bpf can run in patch mode, e.g.,
make -C tools/testing/selftests/bpf run_tests
With the batch mode, I experimented intermittent test failure of
test_xdp_redirect.sh.
....
selftests: test_xdp_redirect [PASS]
selftests: test_xdp_redirect.sh [PASS]
RTNETLINK answers: File exists
selftests: test_xdp_meta [FAILED]
selftests: test_xdp_meta.sh [FAIL]
....
The following illustrates what caused the failure:
(1). test_xdp_redirect creates veth pairs (veth1,veth11) and
(veth2,veth22), and assign veth11 and veth22 to namespace
ns1 and ns2 respectively.
(2). at the end of test_xdp_redirect test, ns1 and ns2 are
deleted. During this process, the deletion of actual
namespace resources, including deletion of veth1{1} and veth2{2},
is put into a workqueue to be processed asynchronously.
(3). test_xdp_meta tries to create veth pair (veth1, veth2).
The previous veth deletions in step (2) have not finished yet,
and veth1 or veth2 may be still valid in the kernel, thus
causing the failure.
The fix is to explicitly delete the veth pair before test_xdp_redirect
exits. Only one end of veth needs deletion as the kernel will delete
the other end automatically. Also test_xdp_meta is also fixed in
similar manner to avoid future potential issues.
Fixes: 996139e801 ("selftests: bpf: add a test for XDP redirect")
Fixes: 22c8852624 ("bpf: improve selftests and add tests for meta pointer")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Test the new MEMBARRIER_CMD_PRIVATE_EXPEDITED_SYNC_CORE and
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_SYNC_CORE commands.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alice Ferrazzi <alice.ferrazzi@gmail.com>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Elder <paul.elder@pitt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Link: http://lkml.kernel.org/r/20180129202020.8515-12-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Test the new MEMBARRIER_CMD_GLOBAL_EXPEDITED and
MEMBARRIER_CMD_REGISTER_GLOBAL_EXPEDITED commands.
Adapt to the MEMBARRIER_CMD_SHARED -> MEMBARRIER_CMD_GLOBAL rename.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alice Ferrazzi <alice.ferrazzi@gmail.com>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Elder <paul.elder@pitt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Link: http://lkml.kernel.org/r/20180129202020.8515-6-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Test the new MEMBARRIER_CMD_PRIVATE_EXPEDITED and
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED commands.
Add checks expecting specific error values on system calls expected to
fail.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alice Ferrazzi <alice.ferrazzi@gmail.com>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Andrew Hunter <ahh@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: David Sehr <sehr@google.com>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maged Michael <maged.michael@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Elder <paul.elder@pitt.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Link: http://lkml.kernel.org/r/20180129202020.8515-2-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-02-02
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) support XDP attach in libbpf, from Eric.
2) minor fixes, from Daniel, Jakub, Yonghong, Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tools and tests to support the multi-port interface
-----BEGIN PGP SIGNATURE-----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=b7cs
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.16' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Bug fixes galore, removal of the ntb atom driver, and updates to the
ntb tools and tests to support the multi-port interface"
* tag 'ntb-4.16' of git://github.com/jonmason/ntb: (37 commits)
NTB: ntb_perf: fix cast to restricted __le32
ntb_perf: Fix an error code in perf_copy_chunk()
ntb_hw_switchtec: Make function switchtec_ntb_remove() static
NTB: ntb_tool: fix memory leak on 'buf' on error exit path
NTB: ntb_perf: fix printing of resource_size_t
NTB: ntb_hw_idt: Set NTB_TOPO_SWITCH topology
NTB: ntb_test: Update ntb_perf tests
NTB: ntb_test: Update ntb_tool MW tests
NTB: ntb_test: Add ntb_tool Message tests
NTB: ntb_test: Update ntb_tool Scratchpad tests
NTB: ntb_test: Update ntb_tool DB tests
NTB: ntb_test: Update ntb_tool link tests
NTB: ntb_test: Add ntb_tool port tests
NTB: ntb_test: Safely use paths with whitespace
NTB: ntb_perf: Add full multi-port NTB API support
NTB: ntb_tool: Add full multi-port NTB API support
NTB: ntb_pp: Add full multi-port NTB API support
NTB: Fix UB/bug in ntb_mw_get_align()
NTB: Set dma mask and dma coherent mask to NTB devices
NTB: Rename NTB messaging API methods
...
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
The libnvdimm unit tests will fail when they are run against the
production / in-tree version of libnvdimm.ko or nfit.ko due to
symbols not being mocked per nfit_test's expectation. For example,
nfit_test expects acpi_evaluate_dsm() to be replaced by
__wrap_acpi_evaluate_dsm() to test how acpi_nfit_ctl() responds to
different stimuli.
Create a test-only symbol name that nfit_test links against to cause
module load failures when the wrong module is present.
For example, with this change, attempts to use the wrong module will
report:
nfit_test: Unknown symbol libnvdimm_test (err 0)
Reported-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding support code to simulate the enabling of LSS status in support of
the Intel DSM v1.6 Function Index 10: Enable Latch System Shutdown Status.
This is only for testing of libndctl support for LSS enable. The actual
functionality requires a reboot and therefore is not simulated. The enable
value is not recorded in nfit_test since there's no DSM to actually query
the current status of the LSS enable.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding support in nfit_test for DSM v1.6 firmware update sequence. The test
will simulate the flashing of firmware to the DIMM. A bogus version string
will be returned as the test has no idea how to parse the firmware binary.
Any bogus binary can be used to "update" as the actual binary is not copied
into the kernel.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
[ vishal: also move smart calls into the nd_cmd_call block ]
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adding NFIT platform capabilities sub table in nfit_test simulated ACPI
NFIT table. Only the first NFIT table is added with the capability
sub-table.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
syzkaller was able to generate the following XDP program ...
(18) r0 = 0x0
(61) r5 = *(u32 *)(r1 +12)
(04) (u32) r0 += (u32) 0
(95) exit
... and trigger a NULL pointer dereference in ___bpf_prog_run()
via bpf_prog_test_run_xdp() where this was attempted to run.
Reason is that recent xdp_rxq_info addition to XDP programs
updated all drivers, but not bpf_prog_test_run_xdp(), where
xdp_buff is set up. Thus when context rewriter does the deref
on the netdev it's NULL at runtime. Fix it by using xdp_rxq
from loopback dev. __netif_get_rx_queue() helper can also be
reused in various other locations later on.
Fixes: 02dd3291b2 ("bpf: finally expose xdp_rxq_info to XDP bpf-programs")
Reported-by: syzbot+1eb094057b338eb1fc00@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fix a couple of issues at tools/testing/selftests/bpf/Makefile so
the following command
make -C tools/testing/selftests/bpf OUTPUT=/home/yhs/tmp
can put the built results into a different directory.
Also add the built binary test_tcpbpf_user in the .gitignore file.
Fixes: 6882804c91 ("selftests/bpf: add a test for overlapping packet range checks")
Fixes: 9d1f159419 ("bpf: move cgroup_helpers from samples/bpf/ to tools/testing/selftesting/bpf/")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Merge updates from Andrew Morton:
- misc fixes
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
mm: remove PG_highmem description
tools, vm: new option to specify kpageflags file
mm/swap.c: make functions and their kernel-doc agree
mm, memory_hotplug: fix memmap initialization
mm: correct comments regarding do_fault_around()
mm: numa: do not trap faults on shared data section pages.
hugetlb, mbind: fall back to default policy if vma is NULL
hugetlb, mempolicy: fix the mbind hugetlb migration
mm, hugetlb: further simplify hugetlb allocation API
mm, hugetlb: get rid of surplus page accounting tricks
mm, hugetlb: do not rely on overcommit limit during migration
mm, hugetlb: integrate giga hugetlb more naturally to the allocation path
mm, hugetlb: unify core page allocation accounting and initialization
mm/memcontrol.c: try harder to decrease [memory,memsw].limit_in_bytes
mm/memcontrol.c: make local symbol static
mm/hmm: fix uninitialized use of 'entry' in hmm_vma_walk_pmd()
include/linux/mmzone.h: fix explanation of lower bits in the SPARSEMEM mem_map pointer
mm/compaction.c: fix comment for try_to_compact_pages()
mm/page_ext.c: make page_ext_init a noop when CONFIG_PAGE_EXTENSION but nothing uses it
zsmalloc: use U suffix for negative literals being shifted
...
The memfd & fuse tests will share more common code in the following
commits to test hugetlb support.
Link: http://lkml.kernel.org/r/20171107122800.25517-9-marcandre.lureau@redhat.com
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove most of the special-casing of hugetlbfs now that sealing is
supported.
Link: http://lkml.kernel.org/r/20171107122800.25517-7-marcandre.lureau@redhat.com
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures like PPC64 support mmap hint address based large address
space selection. This test can be run on those architectures too. Move
the test from the x86 selftests to selftest/vm so that other
architectures can use it too.
We also add a few new test scenarios in this patch. We do test a few
boundary conditions before we do a high address mmap. PPC64 uses the
address limit to validate the address in the fault path. We had bugs in
this area w.r.t SLB fault handling before we updated the addess limit.
We also touch the allocated space to make sure we don't have any bugs in
the fault handling path.
[akpm@linux-foundation.org: restore tools/testing/selftests/vm/Makefile alpha ordering]
Link: http://lkml.kernel.org/r/20171123165226.32582-1-aneesh.kumar@linux.vnet.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle were:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and in
kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends() and
read_barrier_depends().
- Torture-test updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
torture: Save a line in stutter_wait(): while -> for
torture: Eliminate torture_runnable and perf_runnable
torture: Make stutter less vulnerable to compilers and races
locking/locktorture: Fix num reader/writer corner cases
locking/locktorture: Fix rwsem reader_delay
torture: Place all torture-test modules in one MAINTAINERS group
rcutorture/kvm-build.sh: Skip build directory check
rcutorture: Simplify functions.sh include path
rcutorture: Simplify logging
rcutorture/kvm-recheck-*: Improve result directory readability check
rcutorture/kvm.sh: Support execution from any directory
rcutorture/kvm.sh: Use consistent help text for --qemu-args
rcutorture/kvm.sh: Remove unused variable, `alldone`
rcutorture: Remove unused script, config2frag.sh
rcutorture/configinit: Fix build directory error message
rcutorture: Preempt RCU-preempt readers more vigorously
torture: Reduce #ifdefs for preempt_schedule()
rcu: Remove have_rcu_nocb_mask from tree_plugin.h
rcu: Add comment giving debug strategy for double call_rcu()
tracing, rcu: Hide trace event rcu_nocb_wake when not used
...
ntb_perf driver has been also updated so to have the multi-port
interface support. User now must specify what peer port is going
to be used to perform the test.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There are devices (like IDT PCIe switches), which outbound MWs xlat address
is setup on peer side. In this case local side is supposed to allocate
a memory buffer and somehow deliver the xlat DMA address to peer so one
could set the outbound MW up. The MW test is altered so to support both
previous Intel/AMD and new IDT-like devices.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Messages NTB API is now available. ntb_tool driver has been altered
to perform messages send and receive operation. The test of messages
read/write to/from peer device has been added to the script.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Scratchpad NTB API has changed so has the ntb_tool driver. Outbound
Scratchpad DebugFS files have been moved to peer specific directories.
Each scratchpad is now available via separate file. The test code
has been accordingly altered.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
DB interface of ntb_tool driver hasn't been changed much, but
db_valid_mask DebugFS file has still been added. In this case
it's much better to test all valid DB bits instead of using
the predefined mask, which may be incorrect in general.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Link Up and Down methods are used to change NTB link settings on
local side only for multi-port devices. Link is considered up
only if both sides local and peer set it up. Intel/AMD hardware
acts a bit different by assigning the Primary and Secondary roles,
so Primary device only is able to change the link state. Such behaviour
should be reflected in the test code.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Multi-port interface is now available in ntb_tool driver. According
to the new NTB API, there might be more than two devices connected over
NTB. It means each device can have multiple freely enumerated ports.
Each port got index assigned by NTB hardware driver. This test is
performed to determine the local and peer ports as well as their indexes.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If some of variables like LOC/REM or LOCAL_*/REMOTE_* got
whitespaces, the script may fail with syntax error.
Fixes: a9c59ef774 ("ntb_test: Add a selftest script for the NTB subsystem")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-01-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) A number of extensions to tcp-bpf, from Lawrence.
- direct R or R/W access to many tcp_sock fields via bpf_sock_ops
- passing up to 3 arguments to bpf_sock_ops functions
- tcp_sock field bpf_sock_ops_cb_flags for controlling callbacks
- optionally calling bpf_sock_ops program when RTO fires
- optionally calling bpf_sock_ops program when packet is retransmitted
- optionally calling bpf_sock_ops program when TCP state changes
- access to tclass and sk_txhash
- new selftest
2) div/mod exception handling, from Daniel.
One of the ugly leftovers from the early eBPF days is that div/mod
operations based on registers have a hard-coded src_reg == 0 test
in the interpreter as well as in JIT code generators that would
return from the BPF program with exit code 0. This was basically
adopted from cBPF interpreter for historical reasons.
There are multiple reasons why this is very suboptimal and prone
to bugs. To name one: the return code mapping for such abnormal
program exit of 0 does not always match with a suitable program
type's exit code mapping. For example, '0' in tc means action 'ok'
where the packet gets passed further up the stack, which is just
undesirable for such cases (e.g. when implementing policy) and
also does not match with other program types.
After considering _four_ different ways to address the problem,
we adapt the same behavior as on some major archs like ARMv8:
X div 0 results in 0, and X mod 0 results in X. aarch64 and
aarch32 ISA do not generate any traps or otherwise aborts
of program execution for unsigned divides.
Given the options, it seems the most suitable from
all of them, also since major archs have similar schemes in
place. Given this is all in the realm of undefined behavior,
we still have the option to adapt if deemed necessary.
3) sockmap sample refactoring, from John.
4) lpm map get_next_key fixes, from Yonghong.
5) test cleanups, from Alexei and Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new test will spawn four threads, doing map update, delete, lookup
and get_next_key in parallel. It is able to reproduce the issue in the
previous commit found by syzbot and Eric Dumazet.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Update selftests to relfect recent changes and add various new
test cases.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Removed commented lines from test_tcpbpf_kern.c
Fixes: d6d4f60c3a bpf: add selftest for tcpbpf
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Make sure netdevsim doesn't allow offload of chains other than 0,
and that it reports the expected extack message.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should not report errors when offload is not forced.
Check stdout and stderr for familiar messages when with no
skip flags and with skip_hw. Check for add, replace, and
destroy.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a selftest for tcpbpf (sock_ops) that checks that the appropriate
callbacks occured and that it can access tcp_sock fields and that their
values are correct.
Run with command: ./test_tcpbpf_user
Adding the flag "-d" will show why it did not pass.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
mostly revert the previous workaround and make
'dubious pointer arithmetic' test useful again.
Use (ptr - ptr) << const instead of ptr << const to generate large scalar.
The rest stays as before commit 2b36047e78.
Fixes: 2b36047e78 ("selftests/bpf: fix test_align")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel discovered recently I broke TC filter replace (and fixed
it in commit ad9294dbc2 ("bpf: fix cls_bpf on filter replace")).
Add a test to make sure it never happens again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make netdevsim print a message to the BPF verifier log buffer when a
program is offloaded.
Then use this message in hardware offload selftests to make sure that
using this buffer actually prints the message to the console for
eBPF hardware offload.
The message is appended after the last instruction is processed with the
verifying function from netdevsim. Output looks like the following:
$ tc filter add dev foo ingress bpf obj sample_ret0.o \
sec .text verbose skip_sw
Prog section '.text' loaded (5)!
- Type: 3
- Instructions: 2 (0 over limit)
- License:
Verifier analysis:
0: (b7) r0 = 0
1: (95) exit
[netdevsim] Hello from netdevsim!
processed 2 insns, stack depth 0
"verbose" flag is required to see it in the console since netdevsim does
not throw an error after printing the message.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checks to test that netlink extack messages are correctly displayed
in some expected error cases for eBPF offload to netdevsim with TC and
XDP.
iproute2 may be built without libmnl support, in which case the extack
messages will not be reported. Try to detect this condition, and when
enountered print a mild warning to the user and skip the extack validation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: BPF programs and maps related to sockmaps test exist
in memory even after test_maps ends.
This patch fixes it as a short term workaround (sockmap
kernel side needs real fixing) by empyting sockmaps when
test ends.
Fixes: 6f6d33f3b3 ("bpf: selftests add sockmap tests")
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
[ daniel: Note on workaround. ]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The test incorrectly doing
mkdir /mnt/cgroup-test-work-dirtest-bpf-based-device-cgroup
instead of
mkdir /mnt/cgroup-test-work-dir/test-bpf-based-device-cgroup
somehow such mkdir succeeds and new directory appears:
/mnt/cgroup-test-work-dir/cgroup-test-work-dirtest-bpf-based-device-cgroup
Later cleanup via nftw("/mnt/cgroup-test-work-dir", ...);
doesn't walk this directory.
"rmdir /mnt/cgroup-test-work-dir" succeeds, but bpf program and
dangling cgroup stays in memory.
That's a separate issue on a cgroup side.
For now fix the test.
Fixes: 37f1ba0909 ("selftests/bpf: add a test for device cgroup controller")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
test_hashmap_walk takes very long time on debug kernel with kasan on.
Reduce the number of iterations in this test without sacrificing
test coverage.
Also add printfs as progress indicator.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 111e6b4531 ("selftests/bpf: make test_verifier run most programs")
enables tools/testing/selftests/bpf/test_verifier unit cases to run
via bpf_prog_test_run command. With the latest code base,
test_verifier had one test case failure:
...
#473/p check deducing bounds from const, 2 FAIL retval 1 != 0
0: (b7) r0 = 1
1: (75) if r0 s>= 0x1 goto pc+1
R0=inv1 R1=ctx(id=0,off=0,imm=0) R10=fp0,call_-1
2: (95) exit
from 1 to 3: R0=inv1 R1=ctx(id=0,off=0,imm=0) R10=fp0,call_-1
3: (d5) if r0 s<= 0x1 goto pc+1
R0=inv1 R1=ctx(id=0,off=0,imm=0) R10=fp0,call_-1
4: (95) exit
from 3 to 5: R0=inv1 R1=ctx(id=0,off=0,imm=0) R10=fp0,call_-1
5: (1f) r1 -= r0
6: (95) exit
processed 7 insns (limit 131072), stack depth 0
...
The test case does not set return value in the test
structure and hence the return value from the prog run
is assumed to be 0. However, the actual return value is 1.
As a result, the test failed. The fix is to correctly set
the return value in the test structure.
Fixes: 111e6b4531 ("selftests/bpf: make test_verifier run most programs")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a selftest to check if endianness is flipped inadvertently to BE
(MSR.LE set to zero) on BE and LE machines when a trap is caught in
transactional mode and load_fp and load_vec are zero, i.e. when MSR.FP
and MSR.VEC are zeroed (disabled).
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a selftest to exercise the powerpc alignment fault handler.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
[mpe: Add 32-bit support to the signal handler]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds --pgfault and --iterations options to mmap_bench test. With
--pgfault we touch every page mapped. This helps in measuring impact in the
page fault path with a patch series.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-01-19
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) bpf array map HW offload, from Jakub.
2) support for bpf_get_next_key() for LPM map, from Yonghong.
3) test_verifier now runs loaded programs, from Alexei.
4) xdp cpumap monitoring, from Jesper.
5) variety of tests, cleanups and small x64 JIT optimization, from Daniel.
6) user space can now retrieve HW JITed program, from Jiong.
Note there is a minor conflict between Russell's arm32 JIT fixes
and removal of bpf_jit_enable variable by Daniel which should
be resolved by keeping Russell's comment and removing that variable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add couple of missing test cases for eBPF div/mod by zero to the
new test_verifier prog runtime feature. Also one for an empty prog
and only exit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
A test case is added in tools/testing/selftests/bpf/test_lpm_map.c
for MAP_GET_NEXT_KEY command. A four node trie, which
is described in kernel/bpf/lpm_trie.c, is built and the
MAP_GET_NEXT_KEY results are checked.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Check map device information is reported correctly, and perform
basic map operations. Check device destruction gets rid of the
maps and map allocation failure path by telling netdevsim to
reject map offload via DebugFS.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
to improve test coverage make test_verifier run all successfully loaded
programs on 64-byte zero initialized data.
For clsbpf and xdp it means empty 64-byte packet.
For lwt and socket_filters it's 64-byte packet where skb->data
points after L2.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-01-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a divide by zero due to wrong if (src_reg == 0) check in
64-bit mode. Properly handle this in interpreter and mask it
also generically in verifier to guard against similar checks
in JITs, from Eric and Alexei.
2) Fix a bug in arm64 JIT when tail calls are involved and progs
have different stack sizes, from Daniel.
3) Reject stores into BPF context that are not expected BPF_STX |
BPF_MEM variant, from Daniel.
4) Mark dst reg as unknown on {s,u}bounds adjustments when the
src reg has derived bounds from dead branches, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller generated a BPF proglet and triggered a warning with
the following:
0: (b7) r0 = 0
1: (d5) if r0 s<= 0x0 goto pc+0
R0=inv0 R1=ctx(id=0,off=0,imm=0) R10=fp0
2: (1f) r0 -= r1
R0=inv0 R1=ctx(id=0,off=0,imm=0) R10=fp0
verifier internal error: known but bad sbounds
What happens is that in the first insn, r0's min/max value
are both 0 due to the immediate assignment, later in the jsle
test the bounds are updated for the min value in the false
path, meaning, they yield smin_val = 1, smax_val = 0, and when
ctx pointer is subtracted from r0, verifier bails out with the
internal error and throwing a WARN since smin_val != smax_val
for the known constant.
For min_val > max_val scenario it means that reg_set_min_max()
and reg_set_min_max_inv() (which both refine existing bounds)
demonstrated that such branch cannot be taken at runtime.
In above scenario for the case where it will be taken, the
existing [0, 0] bounds are kept intact. Meaning, the rejection
is not due to a verifier internal error, and therefore the
WARN() is not necessary either.
We could just reject such cases in adjust_{ptr,scalar}_min_max_vals()
when either known scalars have smin_val != smax_val or
umin_val != umax_val or any scalar reg with bounds
smin_val > smax_val or umin_val > umax_val. However, there
may be a small risk of breakage of buggy programs, so handle
this more gracefully and in adjust_{ptr,scalar}_min_max_vals()
just taint the dst reg as unknown scalar when we see ops with
such kind of src reg.
Reported-by: syzbot+6d362cadd45dc0a12ba4@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei found that verifier does not reject stores into context
via BPF_ST instead of BPF_STX. And while looking at it, we
also should not allow XADD variant of BPF_STX.
The context rewriter is only assuming either BPF_LDX_MEM- or
BPF_STX_MEM-type operations, thus reject anything other than
that so that assumptions in the rewriter properly hold. Add
test cases as well for BPF selftests.
Fixes: d691f9e8d4 ("bpf: allow programs to write to certain skb fields")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking fixes from David Miller:
1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.
2) Memory leak in key_notify_policy(), from Steffen Klassert.
3) Fix overflow with bpf arrays, from Daniel Borkmann.
4) Fix RDMA regression with mlx5 due to mlx5 no longer using
pci_irq_get_affinity(), from Saeed Mahameed.
5) Missing RCU read locking in nl80211_send_iface() when it calls
ieee80211_bss_get_ie(), from Dominik Brodowski.
6) cfg80211 should check dev_set_name()'s return value, from Johannes
Berg.
7) Missing module license tag in 9p protocol, from Stephen Hemminger.
8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
Maloney.
9) Fix endless loop in netlink extack code, from David Ahern.
10) TLS socket layer sets inverted error codes, resulting in an endless
loop. From Robert Hering.
11) Revert openvswitch erspan tunnel support, it's mis-designed and we
need to kill it before it goes into a real release. From William Tu.
12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net, sched: fix panic when updating miniq {b,q}stats
qed: Fix potential use-after-free in qed_spq_post()
nfp: use the correct index for link speed table
lan78xx: Fix failure in USB Full Speed
sctp: do not allow the v4 socket to bind a v4mapped v6 address
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
ibmvnic: Fix pending MAC address changes
netlink: extack: avoid parenthesized string constant warning
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
net: Allow neigh contructor functions ability to modify the primary_key
sh_eth: fix dumping ARSTR
Revert "openvswitch: Add erspan tunnel support."
net/tls: Fix inverted error codes to avoid endless loop
ipv6: ip6_make_skb() needs to clear cork.base.dst
sctp: avoid compiler warning on implicit fallthru
net: ipv4: Make "ip route get" match iif lo rules again.
netlink: extack needs to be reset each time through loop
tipc: fix a memory leak in tipc_nl_node_get_link()
ipv6: fix udpv6 sendmsg crash caused by too small MTU
...
Commit fbcab13d2e ("selftests: silence test output by default")
changed the run_tests logic as well as the logic to generate
run_kselftests.sh to redirect test output away from the console.
As discussed on the list and at kernel summit, this is not a desirable
default as it means in order to debug a failure the console output is
not sufficient, you also need access to the test machine to get the
full test logs. Additionally it's impolite to write directly to
/tmp/$TEST_NAME on shared systems.
The change to the run_tests logic was reverted in commit
a323335e62 ("selftests: lib.mk: print individual test results to
console by default"), and instead a summary option was added so that
quiet output could be requested.
However the change to run_kselftests.sh was left as-is.
This commit applies the same logic to the run_kselftests.sh code, ie.
the script now takes a "--summary" option which suppresses the output,
but shows all output by default.
Additionally instead of writing to /tmp/$TEST_NAME the output is
redirected to the directory where the generated test script is
located.
Fixes: fbcab13d2e ("selftests: silence test output by default")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Current multiple-kprobe testcase only tries to add
kprobe events on first 256 text symbols. However
kprobes fails to probe on some text symbols (like
blacklisted symbols). Thus in the worst case,
the test can not add any kprobe events.
To avoid that, continue to try adding kprobe events
until 256 events. Also it confirms the number of
registered kprobe events.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Fix to pick text symbols for multiple kprobe testcase.
kallsyms shows text symbols with " t " or " T " but
current testcase picks all symbols including "t",
so it picks data symbols if it includes 't' (e.g. "str").
This fixes it to find symbol lines with " t " or " T "
(including spaces).
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Russell King <linux@armlinux.org.uk>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
This tests that the vsyscall entries do what they're expected to do.
It also confirms that attempts to read the vsyscall page behave as
expected.
If changes are made to the vsyscall code or its memory map handling,
running this test in all three of vsyscall=none, vsyscall=emulate,
and vsyscall=native are helpful.
(Because it's easy, this also compares the vsyscall results to their
vDSO equivalents.)
Note to KAISER backporters: please test this under all three
vsyscall modes. Also, in the emulate and native modes, make sure
that test_vsyscall_64 agrees with the command line or config
option as to which mode you're in. It's quite easy to mess up
the kernel such that native mode accidentally emulates
or vice versa.
Greg, etc: please backport this to all your Meltdown-patched
kernels. It'll help make sure the patches didn't regress
vsyscalls.
CSigned-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/2b9c5a174c1d60fd7774461d518aa75598b1d8fd.1515719552.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove 'clean' target and change TEST_PROGS to TEST_GEN_PROGS so the
common lib.mk 'clean' target clean these generated files. TEST_PROGS
is for shell scripts and not for generated test executables.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
