Add API to delete custom DDMA device ids create with
au1xxx_ddma_device_add().
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xmmc.c driver depends on it, so export it for modules.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, fpu: fix CONFIG_PREEMPT=y corruption of application's FPU stack
suspend-vs-iommu: prevent suspend if we could not resume
x86: section mismatch fix
x86: fix Xorg crash with xf86MapVidMem error
x86: fix pointer type warning in arch/x86/mm/init_64.c:early_memtest
x86: fix bad pmd ffff810000207xxx(9090909090909090)
x86: ioremap fix failing nesting check
x86: fix broken math-emu with lazy allocation of fpu area
x86: enable preemption in delay
x86: disable preemption in native_smp_prepare_cpus
x86: fix APIC warning on 32bit v2
Jürgen Mell reported an FPU state corruption bug under CONFIG_PREEMPT,
and bisected it to commit v2.6.19-1363-gacc2076, "i386: add sleazy FPU
optimization".
Add tsk_used_math() checks to prevent calling math_state_restore()
which can sleep in the case of !tsk_used_math(). This prevents
making a blocking call in __switch_to().
Apparently "fpu_counter > 5" check is not enough, as in some signal handling
and fork/exec scenarios, fpu_counter > 5 and !tsk_used_math() is possible.
It's a side effect though. This is the failing scenario:
process 'A' in save_i387_ia32() just after clear_used_math()
Got an interrupt and pre-empted out.
At the next context switch to process 'A' again, kernel tries to restore
the math state proactively and sees a fpu_counter > 0 and !tsk_used_math()
This results in init_fpu() during the __switch_to()'s math_state_restore()
And resulting in fpu corruption which will be saved/restored
(save_i387_fxsave and restore_i387_fxsave) during the remaining
part of the signal handling after the context switch.
Bisected-by: Jürgen Mell <j.mell@t-online.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Jürgen Mell <j.mell@t-online.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
iommu/gart support misses suspend/resume code, which can do bad stuff,
including memory corruption on resume. Prevent system suspend in case we
would be unable to resume.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Tested-by: Patrick <ragamuffin@datacomm.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this:
WARNING: vmlinux.o(.text+0x114bb): Section mismatch in reference from
the function nopat() to the function .cpuinit.text:pat_disable()
The function nopat() references
the function __cpuinit pat_disable().
This is often because nopat lacks a __cpuinit
annotation or the annotation of pat_disable is wrong.
Reported-by: "Fabio Comolli" <fabio.comolli@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clarify the usage of mtrr_lookup() in PAT code, and to make PAT code
resilient to mtrr lookup problems.
Specifically, pat_x_mtrr_type() is restructured to highlight, under what
conditions we look for mtrr hint. pat_x_mtrr_type() uses a default type
when there are any errors in mtrr lookup (still maintaining the pat
consistency). And, reserve_memtype() highlights its usage ot mtrr_lookup
for request type of '-1' and also defaults in a sane way on any mtrr
lookup failure.
pat.c looks at mtrr type of a range to get a hint on what mapping type
to request when user/API: (1) hasn't specified any type (/dev/mem
mapping) and we do not want to take performance hit by always mapping
UC_MINUS. This will be the case for /dev/mem mappings used to map BIOS
area or ACPI region which are WB'able. In this case, as long as MTRR is
not WB, PAT will request UC_MINUS for such mappings.
(2) user/API requests WB mapping while in reality MTRR may have UC or
WC. In this case, PAT can map as WB (without checking MTRR) and still
effective type will be UC or WC. But, a subsequent request to map same
region as UC or WC may fail, as the region will get trackked as WB in
PAT list. Looking at MTRR hint helps us to track based on effective type
rather than what user requested. Again, here mtrr_lookup is only used as
hint and we fallback to WB mapping (as requested by user) as default.
In both cases, after using the mtrr hint, we still go through the
memtype list to make sure there are no inconsistencies among multiple
users.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Rufus & Azrael <rufus-azrael@numericable.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Changed the call to find_e820_area_size to pass u64 instead of unsigned long.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
OGAWA Hirofumi and Fede have reported rare pmd_ERROR messages:
mm/memory.c:127: bad pmd ffff810000207xxx(9090909090909090).
Initialization's cleanup_highmap was leaving alignment filler
behind in the pmd for MODULES_VADDR: when vmalloc's guard page
would occupy a new page table, it's not allocated, and then
module unload's vfree hits the bad 9090 pmd entry left over.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mika Kukkonen noticed that the nesting check in early_iounmap() is not
actually done.
Reported-by: Mika Kukkonen <mikukkon@srv1-m700-lanp.koti>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: torvalds@linux-foundation.org
Cc: arjan@linux.intel.com
Cc: mikukkon@iki.fi
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the math emulation that got broken with the recent lazy allocation of FPU
area. init_fpu() need to be added for the math-emulation path aswell
for the FPU area allocation.
math emulation enabled kernel booted fine with this, in the presence
of "no387 nofxsr" boot param.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: hpa@zytor.com
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The RT team has been searching for a nasty latency. This latency shows
up out of the blue and has been seen to be as big as 5ms!
Using ftrace I found the cause of the latency.
pcscd-2995 3dNh1 52360300us : irq_exit (smp_apic_timer_interrupt)
pcscd-2995 3dN.2 52360301us : idle_cpu (irq_exit)
pcscd-2995 3dN.2 52360301us : rcu_irq_exit (irq_exit)
pcscd-2995 3dN.1 52360771us : smp_apic_timer_interrupt (apic_timer_interrupt
)
pcscd-2995 3dN.1 52360771us : exit_idle (smp_apic_timer_interrupt)
Here's an example of a 400 us latency. pcscd took a timer interrupt and
returned with "need resched" enabled, but did not reschedule until after
the next interrupt came in at 52360771us 400us later!
At first I thought we somehow missed a preemption check in entry.S. But
I also noticed that this always seemed to happen during a __delay call.
pcscd-2995 3dN.2 52360836us : rcu_irq_exit (irq_exit)
pcscd-2995 3.N.. 52361265us : preempt_schedule (__delay)
Looking at the x86 delay, I found my problem.
In git commit 35d5d08a08, Andrew Morton
placed preempt_disable around the entire delay due to TSC's not working
nicely on SMP. Unfortunately for those that care about latencies this
is devastating! Especially when we have callers to mdelay(8).
Here I enable preemption during the loop and account for anytime the task
migrates to a new CPU. The delay asked for may be extended a bit by
the migration, but delay only guarantees that it will delay for that minimum
time. Delaying longer should not be an issue.
[
Thanks to Thomas Gleixner for spotting that cpu wasn't updated,
and to place the rep_nop between preempt_enabled/disable.
]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: akpm@osdl.org
Cc: Clark Williams <clark.williams@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Luis Claudio R. Goncalves" <lclaudio@uudg.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <andi-suse@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
for http://bugzilla.kernel.org/show_bug.cgi?id=10613
BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor)
v2: fix 64 bit compilation
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
RSK7203 is supportable through the generic machvec, so we add a defconfig
for those bits. This gets updated with more complete board support later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
8250 Serial Driver: revert extra IRQ flag definition patch
Blackfin arch: update anomaly headers from toolchain trunk
Blackfin arch: Remove bad and usless code
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
Blackfin arch: Fix typo. it should be _outsw_8
Blackfin arch: Cleanup no functional changes
Work around:
arch/arm/mach-pxa/tosa.c: In function `tosa_poweroff':
arch/arm/mach-pxa/tosa.c:470: error: `GPIO_OUT' undeclared (first use in this function)
arch/arm/mach-pxa/tosa.c:470: error: (Each undeclared identifier is reported only once
arch/arm/mach-pxa/tosa.c:470: error: for each function it appears in.)
The proper fix exists in the PXA branch of my kernel git tree, which
will be pushed during the next merge window.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IORESOURCE_IRQ_HIGHEDGE to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iommu/gart support misses suspend/resume code, which can do bad stuff,
including memory corruption on resume. Prevent system suspend in case we
would be unable to resume.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Tested-by: Patrick <ragamuffin@datacomm.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Wed, 2008-05-28 at 04:47 +0200, Andi Kleen wrote:
> > So... why not just remove the setting of __GFP_NORETRY? Why is it
> > wrong to oom-kill things in this case?
>
> When the 16MB zone overflows (which can be common in some workloads)
> calling the OOM killer is pretty useless because it has barely any
> real user data [only exception would be the "only 16MB" case Alan
> mentioned]. Killing random processes in this case is bad.
>
> I think for 16MB __GFP_NORETRY is ok because there should be
> nothing freeable in there so looping is useless. Only exception would be the
> "only 16MB total" case again but I'm not sure 2.6 supports that at all
> on x86.
>
> On the other hand d_a_c() does more allocations than just 16MB, especially
> on 64bit and the other zones need different strategies.
Okay, so how about this then ?
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
4k stacks on nommu ends up blowing up with all sorts of interesting
slab corruption. Disable this by default unless BROKEN is also
enabled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following build error caused by
commit a1dc4b59fa
(sh: intc_sh5 depends on cayman board for IRQ priority table.):
<-- snip -->
...
CC arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AD7877 use SSEL_2 (P9.9) and IRQ_PF8 (P9.14) on BF527
- populating JP3 to enable STAMP
- disable SW11.2 to disconnect SSEL_2/PF12 from Rotary NAND
- disable SW18.1 to disconnect SSEL_2 from MAX1233 touchscreen chip
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently ext4 and fuse fail to link if modular:
ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
make[3]: *** [__modpost] Error 1
make[2]: *** [modules] Error 2
make[1]: *** [sub-make] Error 2
While arch ppc exists it may as well compile, so this exports those
symbols (which are already exported in arch/powerpc).
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
The correct instruction format of idte is "idte r1,r3,r2" with
r1 at bit 24, r3 at bit 16 and r2 at bit 28.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert show_mem() so its nearly the same as on x86/powerpc.
Gives us proper locking and we get also rid of the only use of max_mapnr.
Also the number of pages was contained in an int which might not be
sufficient not too far in the future.
Cc: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use get_online_cpus() to prevent cpu hotplug in situations where
for_each_online_cpu() is called.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes the last remaining section mismatch warnings in s390
architecture code. It reveals also a real bug introduced by... me
with git commit 2069e978d5
("[S390] sparsemem vmemmap: initialize memmap.")
Calling the generic vmemmap_alloc_block() function to get initialized
memory is a nice idea, however that function is __meminit annotated
and therefore the function might be gone if we try to call it later.
This can happen if a DCSS segment gets added.
So basically revert the patch and clear the memmap explicitly to fix
the original bug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On s390 make allnoconfig fails with the following build error:
arch/s390/mm/init.c: In function 'show_mem':
arch/s390/mm/init.c:55: error: implicit declaration of function 'pfn_valid'
make[1]: *** [arch/s390/mm/init.o] Error 1
make: *** [arch/s390/mm] Error 2
This problem can by fixed ensuring that ARCH_SELECT_MEMORY_MODEL
is always turned on.
Signed-off-by: Hans-Joachim Picht <hans@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Problem: An application violating the architectural rules regarding
operation dependencies and having specific Register Stack Engine (RSE)
state at the time of the violation, may result in an illegal operation
fault and invalid RSE state. Such faults may initiate a cascade of
repeated illegal operation faults within OS interruption handlers.
The specific behavior is OS dependent.
Implication: An application causing an illegal operation fault with
specific RSE state may result in a series of illegal operation faults
and an eventual OS stack overflow condition.
Workaround: OS interruption handlers that switch to kernel backing
store implement a check for invalid RSE state to avoid the series
of illegal operation faults.
The core of the workaround is the RSE_WORKAROUND code sequence
inserted into each invocation of the SAVE_MIN_WITH_COVER and
SAVE_MIN_WITH_COVER_R19 macros. This sequence includes hard-coded
constants that depend on the number of stacked physical registers
being 96. The rest of this patch consists of code to disable this
workaround should this not be the case (with the presumption that
if a future Itanium processor increases the number of registers, it
would also remove the need for this patch).
Move the start of the RBS up to a mod32 boundary to avoid some
corner cases.
The dispatch_illegal_op_fault code outgrew the spot it was
squatting in when built with this patch and CONFIG_VIRT_CPU_ACCOUNTING=y
Move it out to the end of the ivt.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move the AP7 cpufreq init to late_initcall() so that we don't try to
bring up cpufreq until the governor is ready. x86 also uses
late_initcall() for this.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
sh: Drop broken URAM support on SH7723.
sh: update Migo-R defconfig
sh: use sm501 8250 mfd support on r2d boards
sh: add probe support for new sh7723 cut
sh: fix VPU interrupt vector for sh7723
sh: fix USBF resource for sh7722
Just provide reasonable defaults for the new stuff. Tickless and
hrtimers are turned on for all boards except ATSTK1004.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This was copied over from the previous MobileR bits, which doesn't
apply to R2. The URAM block on R2 is recycled for the L2 instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
init/Kconfig contains a list of configs that are searched
for if 'make *config' are used with no .config present.
Extend this list to look at the config identified by
ARCH_DEFCONFIG.
With this change we now try the defconfig targets last.
This fixes a regression reported
by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: prevent PGE flush from interruption/preemption
x86: use explicit copy in vdso_gettimeofday()
namespacecheck: automated fixes
x86/xen: fix arbitrary_virt_to_machine()
x86: don't read maxlvt before checking if APIC is mapped
x86: disable TSC for sched_clock() when calibration failed
x86: distangle user disabled TSC from unstable
x86: fix setup of cyc2ns in tsc_64.c
Fix the following build error:
ERROR: "empty_zero_page" [fs/ext4/ext4dev.ko] undefined!
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] iSeries: Remove unused mail address
[POWERPC] mpic: Fix use of uninitialized variable
[POWERPC] Add kernstart_addr to list of allowed symbols in prom_init
[POWERPC] Fix __set_fixmap() for STRICT_MM_TYPECHECKS
[POWERPC] PS3: Fix memory hotplug
Export the AT91 clock functions for the AT91X40. Some external code common
to all AT91 family parts relys on this, like the gpio and serial support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jeremy's gcc 3.4 seems to be unable to inline a 8 byte memcpy. But the
vdso doesn't support external references. Copy the structure members
of struct timezone explicitely instead.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While I realize that the function isn't currently being used, I still
think an obvious mistake like this should be corrected.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A check for unmapped apic was added before reading maxlvt but the early
read of maxlvt wasn't removed.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
When the TSC calibration fails then TSC is still used in
sched_clock(). Disable it completely in that case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
tsc_enabled is set to 0 from the command line switch "notsc" and from
the mark_tsc_unstable code. Seperate those functionalities and replace
tsc_enable with tsc_disable. This makes also the native_sched_clock()
decision when to use TSC understandable.
Preparatory patch to solve the sched_clock() issue on 32 bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the TSC is calibrated against the PIT due to the nonavailability
of PMTIMER/HPET or due to SMI interference then the setup of the per
CPU cyc2ns variables is skipped. This is unlikely to happen but it
would definitely render sched_clock() unusable.
This was introduced with commit 53d517cdba
x86: scale cyc_2_nsec according to CPU frequency
Update the per CPU cyc2ns variables in all exit pathes of tsc_calibrate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Compiling ppc64_defconfig with gcc 4.3 gives thes warnings:
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_get_priority':
arch/powerpc/sysdev/mpic.c:1351: warning: 'is_ipi' may be used uninitialized in this function
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_set_priority':
arch/powerpc/sysdev/mpic.c:1328: warning: 'is_ipi' may be used uninitialized in this function
It turns out that in the cases where is_ipi is uninitialized, another
variable (mpic) will be NULL and it is dereferenced. Protect against
this by returning if mpic is NULL in mpic_irq_set_priority, and removing
mpic_irq_get_priority completely as it has no in tree callers.
This has the nice side effect of making the warning go away.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since commit "85xx: Add support for relocatable kernel (and
booting at non-zero)" (37dd2badcf),
PHYSICAL_START is #defined as kernstart_addr if RELOCATABLE
and FLATMEM is enabled.
PHYSICAL_START is used in prom_init.c and so kernstart_addr
needs to be added to the list of allowed symbols that
prom_init.c can access.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__set_fixmap() in pgtable_32.c currently fails to compile if
STRICT_MM_TYPECHECKS is defined. This fixes it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A change was made to walk_memory_resource() in commit
4b119e21d0 that added a
check of find_lmb(). Add the coresponding lmb_add()
call to ps3_mm_add_memory() so that that check will
succeed.
This fixes the condition where the PS3 boots up with
only the 128 MiB of boot memory, and doesn't see the
other 128MiB that is available.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the Migo-R defconfig to include support for KEYSC, I2C, RTC and
NAND and NOR MTD devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make use of recently added sm501 8250 uart support, commit
61711f8fd8 makes the mfd code
handle 8250 uarts so there is no longer need to do it from
the r2d board code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for sh7723 silicon with a prr value of 0x51.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a VPU vector typo for sh7723. The correct value is 0x980,
the same as for sh7722.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The USBF function on sh7722 is currently not working with the m66592_udc
driver. The driver is using platform_get_resource_byname() so my commit
a0d29798e5 broke sh7722 support.
The long term fix is to replace platform_get_resource_byname() in the
driver with platform_get_resource(), but this helps until that happens.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Greetings.
There is a code flaw in the bfsort whitelist, where there are redundant
entries for the same two HP systems, DL385 G2 and DL585 G2. This patch
replaces those redundant entries with the correct ones. The correct
entries are for large-volume systems, the DL360 and DL380.
-----------------------------------------------------------------------
commit ec69f0374c3b0ad7ea991b0e9ac00377acfe5b1a
Author: Tony Camuso <tony.camuso@hp.com>
Date: Wed May 14 07:09:28 2008 -0400
Replace Redundant Whitelist Entries with the Correct Ones
The ProLiant DL585 G2 and the DL585 G2 are entered reundantly
in the dmi_system_id table. What should have been there are the
DL360 and DL380. This patch simply replaces the redundant
entries with the correct entries.
arch/x86/pci/common.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename the SDI device if on an S3C2440 or S3C2442.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IRQF_TRIGGER_ type to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the IRQF_TRIGGER_ type to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As noted by Russell King. These depend on tsc210x drivers
getting integrated first.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
collie.h:
* add some meaningfull names to some gpios
collie.c:
* initialize cpu registers correctly
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we fully commit to returning back to kernel mode from
a trap, zero out the regs->magic value to prevent false
positives during stack backtraces.
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset to the pt_regs area was wrong, so we weren't
looking at the right location for the magic cookie.
A trap frame is composed of a "struct sparc_stackf" then
a "struct pt_regs", the code was using "struct reg_window"
instead of "struct sparc_stackf".
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of the silly way I set up the initial stack for
new kernel threads, there is a loop at the top of the
stack.
To fix this, properly add another stack frame that is copied
from the parent and terminate it in the child by setting
the frame pointer in that frame to zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Whether we sidestep it in init/main.c or not, such situations
will arise again; compiler does generate calls of strcat()
on optimizations, so we really ought to have an out-of-line
version...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... and we have few enough places using the latter to make it
simpler to do search and replace...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want sys/ptrace.h before any includes of linux/ptrace.h and
asm/user.h pulls the latter.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: correct mailing list address
PCI: Correct last two HP entries in the bfsort whitelist
When a cpu really is stuck in the kernel, it can be often
impossible to figure out which cpu is stuck where. The
worst case is when the stuck cpu has interrupts disabled.
Therefore, implement a global cpu state capture that uses
SMP message interrupts which are not disabled by the
normal IRQ enable/disable APIs of the kernel.
As long as we can get a sysrq 'y' to the kernel, we can
get a dump. Even if the console interrupt cpu is wedged,
we can trigger it from userspace using /proc/sysrq-trigger
The output is made compact so that this facility is more
useful on high cpu count systems, which is where this
facility will likely find itself the most useful :)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dtbImage.* and several zImage. targets get created but never cleaned up.
Also, moved zImage to the clean-files line associated with all other image
results (was previously duplicated).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] return to old errno choice in mkdir() et.al.
[Patch] fs/binfmt_elf.c: fix wrong return values
[PATCH] get rid of leak in compat_execve()
[Patch] fs/binfmt_elf.c: fix a wrong free
[PATCH] avoid multiplication overflows and signedness issues for max_fds
[PATCH] dup_fd() part 4 - race fix
[PATCH] dup_fd() - part 3
[PATCH] dup_fd() part 2
[PATCH] dup_fd() fixes, part 1
[PATCH] take init_files to fs/file.c
This removes a CVS keyword that wasn't updated for a long time from a
comment.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin SPORTS UART Driver: converting BFIN->BLACKFIN
Blackfin serial driver: add extra IRQ flag for 8250 serial driver
8250 Serial Driver: Added support for 8250-class UARTs in HV Sistemas H8606 board
Blackfin arch: Fix bug - USB fails to build for BF524/BF526
Blackfin arch: update boards defconfig files
Blackfin arch: IO Port functions to read/write unalligned memory
Blackfin arch: enable a choice to provide 4M DMA memory
Blackfin arch: cleanup the icplb/dcplb multiple hit checks
Blackfin arch: Add workaround to read edge triggered GPIOs
Blackfin arch: Sync channel defines with struct dma_register dma_io_base_addr.
Blackfin arch: Check for Anomaly 05000182
[Blackfin] arch: rename bf5xx-flash to bfin-async-flash
[Blackfin] arch: Blackfin checksum annotations
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up restorer in debug_trap exception return path.
sh: Make is_valid_bugaddr() more intelligent on nommu.
sh: use the common ascii hex helpers
sh: fix sh7785 master clock value
sh: Fix up thread info pointer in syscall_badsys resume path.
sh: Fix up optimized SH-4 memcpy on big endian.
sh: disable initrd defaults in .empty_zero_page.
sh: display boot params by default on entry.
The longrun cpufreq module reports a false minimum frequency 3MHz on
300-600MHz Crusoe processor. This may be due to a calculation bug
in the module.
Original patch from Kaz Sasayama <kazssym@hypercore.co.jp>
submitted as http://bugs.debian.org/468149 patch ported to x86
Cc: Kaz Sasayama <kazssym@hypercore.co.jp>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Dave Jones <davej@redhat.com>
The most common error with powernow-k8 is an ACPI _PSS error
caused either by failure to load the ACPI processor module
or a bad parse of the _PSS object. Make the error message
returned to the user in these situations more straightforward
and easier to understand.
-Mark Langsdorf
Operating System Research Center
AMD
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: LAPIC: ignore pending timers if LVTT is disabled
KVM: Update MAINTAINERS for new mailing lists
KVM: Fix kvm_vcpu_block() task state race
KVM: ia64: Set KVM_IOAPIC_NUM_PINS to 48
KVM: ia64: fix GVMM module including position-dependent objects
KVM: ia64: Define new kvm_fpreg struture to replace ia64_fpreg
KVM: PIT: take inject_pending into account when emulating hlt
s390: KVM guest: fix compile error
KVM: x86 emulator: fix writes to registers with modrm encodings
Replace Redundant Whitelist Entries with the Correct Ones
The ProLiant DL585 G2 and the DL585 G2 are entered reundantly in the
dmi_system_id table. What should have been there are the DL360 and DL380. This
patch simply replaces the redundant entries with the correct entries.
Signed-off-by: Tony Camuso <tony.camuso@hp.com>
Signed-off-by: Pat Schoeller <patrick.schoeller@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PowerPC 440EP, 440GR, 440EPx, and 440GRx chips have an issue that
causes the PLB3-to-PLB4 bridge to wait indefinitely for transaction
requests that cross the end-of-memory-range boundary. Since the DDR
controller only returns the valid portion of a read request, the bridge
will prevent other PLB masters from completing their transactions.
This implements the recommended workaround for this errata for chips that
use older versions of firmware that do not already handle it. The last
4KiB of memory are hidden from the kernel to prevent the problem
transactions from occurring.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
There are a few different types of debug trap exceptions, though now
that they are all going through a special jump table, the restorer needs
to be unified as well.
Presently this is falling through the ret_from_fork path, which more or
less does the right thing on SH-3/4 whilst being completely unsuitable on
MMU-less targets.
Ultimately what we want here is a branch through the platform's
restore_all directly, without worrying about the retval being clobbered.
We can accomplish that through a branch to __restore_all directly, so
switch it so we come back from the jump table and branch to the restorer.
This fixes up a recursion in the nommu WARN_ON() path, as well as some
other userspace nastiness where said recursion caused serious stack
corruption.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently is_valid_bugaddr() is true for anything >= PAGE_OFFSET, which
happens to be 0 on nommu configurations. Make this a bit smarter by just
reading in the opcode and comparing it against the trap type that we
already know. Follows the logic from avr32.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/max6875: Really prevent 24RF08 corruption
i2c-amd756: Fix functionality flags
i2c: Kill the old driver matching scheme
i2c: Convert remaining new-style drivers to use module aliasing
i2c: Switch pasemi to the new device/driver matching scheme
i2c: Clean up Blackfin BF527 I2C device declarations
i2c-nforce2: Disable the second SMBus channel on the DFI Lanparty NF4 Expert
i2c: New co-maintainer
Add multi_defconfig, to build a kernel for all supported m68k platforms,
excluding Sun 3 (Sun 3 kernels are incompatible with all other m68k platforms)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The *_ISA type defines are quite generic and cause namespace conflicts
(e.g. with `AMIGAHW_DECLARE(GG2_ISA)' in <asm/amigahw.h>) for some kernel
configurations. Use ISA_TYPE_* to avoid such conflicts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Q40/Q60 floppy support broken:
arch/m68k/q40/q40ints.c: In function 'q40_irq_handler':
arch/m68k/q40/q40ints.c:214: error: implicit declaration of function 'floppy_hardint'
Including <asm/floppy.h> doesn't help, as it causes a lot of additional error
messages (cfr. Sun 3x).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running a HP300-enabled kernel on non-HP300 hardware, a test in the early
startup code jumps to the wrong label, causing a double bus fault.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Hisoft Whippet PCMCIA serial driver has been removed a long time ago, but
it's Kconfig symbol still existed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old device/driver matching scheme is going away so stop using it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Olof Johansson <olof@lixom.net>
I2C_BOARD_INFO() now sets the type field so no need to set it
separatetly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Bryan Wu <cooloney@kernel.org>
Only use the APIC pending timers count to break out of HLT emulation if
the timer vector is enabled.
Certain configurations of Windows simply mask out the vector without
disabling the timer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The GVMM module is position independent since it is relocated to the guest
address space.
Commit ea696f9cf ("ia64 kvm fixes for O=... builds") broke this by linking
GVMM with non-PIC objects.
Fix by creating two files: memset.S and memcpy.S which just include the files
under arch/ia64/lib/{memset.S, memcpy.S} respectively.
[akpm: don't delete files which we need]
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Otherwise hlt emulation fails if PIT is not injecting IRQ's.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A register destination encoded with a mod=3 encoding left dst.ptr NULL.
Normally we don't trap writes to registers, but in the case of smsw, we do.
Fix by pointing dst.ptr at the destination register.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Two changes are necessary to enable proper operation of the DM9000 device with
the Colibri PXA 270 board: firstly, the IRQ type needs to be configured for
rising edge interrupts, and secondly this configuration needs to be
communicated through to the DM9000.
[akpm@linux-foundation.org: remove set_irq_type() call as per ben-linux request]
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Cc: Daniel Mack <daniel@caiaq.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Whereas most Orion 5x machine support code would initialise the PCI
subsystem with nr_controllers in their struct hw_pci set to 2, the
DNS323 and Kurobox Pro machine support code had nr_controllers set
to 1.
This was presumably done because on those two machines, the PCI(-X)
controller (nr == 1) isn't used, requiring initialisation of only
the PCIe controller (nr == 0.) However, not initialising the PCI(-X)
controller on boards that don't use it leads to a situation where
both the PCIe and the PCI(-X) controller think that their root bus is
zero, and it messes up IRQ assignment.
This patch changes the DNS323 and Kurobox Pro support code to always
use nr_controllers == 2.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU's dma_flush_range() operation needs to clean+invalidate the
given memory area if the cache is in writeback mode, or do just the
invalidate part if the cache is in writethrough mode, but the current
proc-arm{925,926,940,946} (incorrectly) do a cache clean in the
latter case. This patch fixes that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Martin Michlmayr reported that fuse complains:
ERROR: "copy_page" [fs/fuse/fuse.ko] undefined!
so export the needed function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irqs.h:
* rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
* add some definition for locomo spi controller
* correct some errors
locomo.c:
* correct some errors
* add set_type for locomo gpio irq chip
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: disable mwait for AMD family 10H/11H CPUs
x86: fix crash on cpu hotplug on pat-incapable machines
x86: remove mwait capability C-state check
The previous revert of 0c07ee38c9 left
out the mwait disable condition for AMD family 10H/11H CPUs.
Andreas Herrman said:
It depends on the CPU. For AMD CPUs that support MWAIT this is wrong.
Family 0x10 and 0x11 CPUs will enter C1 on HLT. Powersavings then
depend on a clock divisor and current Pstate of the core.
If all cores of a processor are in halt state (C1) the processor can
enter the C1E (C1 enhanced) state. If mwait is used this will never
happen.
Thus HLT saves more power than MWAIT here.
It might be best to switch off the mwait flag for these AMD CPU
families like it was introduced with commit
f039b75471 (x86: Don't use MWAIT on AMD
Family 10)
Re-add the AMD families 10H/11H check and disable the mwait usage for
those.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
pat_disable() is __init, which means it goes away after booting is complete.
Unfortunately it is used by the hotplug code if the machine is not
pat-capable, causing a crash.
Fix by marking pat_disable() as __cpuinit.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vegard Nossum reports:
| powertop shows between 200-400 wakeups/second with the description
| "<kernel IPI>: Rescheduling interrupts" when all processors have load (e.g.
| I need to run two busy-loops on my 2-CPU system for this to show up).
|
| The bisect resulted in this commit:
|
| commit 0c07ee38c9
| Date: Wed Jan 30 13:33:16 2008 +0100
|
| x86: use the correct cpuid method to detect MWAIT support for C states
remove the functional effects of this patch and make mwait unconditional.
A future patch will turn off mwait on specific CPUs where that causes
power to be wasted.
Bisected-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
support two cascaded AD73322 cards, more uncached DMA
memory is needed, so add a choice to provide 4M DMA memory
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
so that we always send the same signal and we handle the NULL ptr condition properly
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
IMDMA does not operate to full speed for 600MHz and higher devices
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This fixes the missing ram regression reported by
Mikael Pettersson <mikpe@it.uu.se>, much thanks for
all of this help in diagnosing this.
The second argument to lmb_reserve() is a size,
not an end address bounds.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Entry to resume_userspace expects r8 to contain current_thread_info,
which happens in all paths except for syscall_badsys, where r8 was
being inadvertently trampled. Reload it before the branch.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When using initramfs on systems that don't explicitly clear LOADER_TYPE,
unpack_to_rootfs() tramples tramples the range with the defaults taken
out of .empty_zero_page. This causes kernels with valid initramfs images
to bail out with crc or gzip magic mismatch errors after the second
unpack takes place on certain platform configurations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some kernel and boot loader configurations tweak the .empty_zero_page
settings, while others do not. Print the values out on entry as a
debugging aid.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] macintosh: Replace deprecated __initcall with device_initcall
[POWERPC] cell: Fix section mismatches in io-workarounds code
[POWERPC] spufs: Fix compile error
[POWERPC] Fix uninitialized variable bug in copy_{to|from}_user
[POWERPC] Add null pointer check to of_find_property
[POWERPC] vmemmap fixes to use smaller pages
[POWERPC] spufs: Fix pointer reference in find_victim
[POWERPC] 85xx: SBC8548 - Add flash support and HW Rev reporting
[POWERPC] 85xx: Fix some sparse warnings for 85xx MDS
[POWERPC] 83xx: Enable DMA engine on the MPC8377 MDS board.
[POWERPC] 86xx: mpc8610_hpcd: fix second serial port
[POWERPC] 86xx: mpc8610_hpcd: add support for NOR and NAND flashes
[POWERPC] 85xx: Add 8568 PHY workarounds to board code
[POWERPC] 86xx: mpc8610_hpcd: use ULI526X driver for on-board ethernet
The patch aims to fix a performance issue for the syscall
personality(PER_LINUX32).
On IA-64 box, the syscall personality (PER_LINUX32) has poor performance
because it failed to find the Linux/x86 execution domain. Then it tried
to load the kernel module however it failed always and it used the default
execution domain PER_LINUX instead. Requesting kernel modules is very
expensive. It caused the performance issue. (see the function
lookup_exec_domain in kernel/exec_domain.c).
To resolve the issue, execution domain Linux/x86 is always registered in
initialization time for IA-64 architecture.
Signed-off-by: Xiaolan Huang <xiaolan.huang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] show_interrupts: prevent cpu hotplug when walking cpu_online_map.
[S390] smp: __smp_call_function_map vs cpu_online_map fix.
[S390] tape: Use ccw_dev_id to build cdev_id.
[S390] dasd: fix timeout handling in interrupt handler
[S390] s390dbf: Use const char * for dbf name.
[S390] dasd: Use const in busid functions.
[S390] blacklist.c: removed duplicated include
[S390] vmlogrdr: module initialization function should return negative errors
[S390] sparsemem vmemmap: initialize memmap.
[S390] Remove last traces of cio_msg=.
[S390] cio: Remove CCW_CMD_SUSPEND_RECONN in front of CCW_CMD_SET_PGID.
Surround all the code withing show_interrupts() with
get/put_online_cpus() to prevent strange results wrt cpu hotplug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Both smp_call_function() and __smp_call_function_map() access
cpu_online_map. Both functions run with preemption disabled which
protects for cpus going offline. However new cpus can be added and
therefore the cpu_online_map can change unexpectedly.
So use the call_lock to protect against changes to the cpu_online_map
in start_secondary() and all smp_call_* functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We should use const char * for passing the name of the debug feature
around since it will not be changed.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let's just use the generic vmmemmap_alloc_block() function which
always returns initialized memory.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.
So use the time_after() macro, defined in linux/jiffies.h, which deals with
wrapping correctl
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.
The two outputs only differ in text formatting:
printk("Free swap = %lukB\n", ...);
printk("Free swap: %6ldkB\n", ...);
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
This trivial patch fixes the following section warnings on PARISC:
> WARNING: vmlinux.o (.text.1): unexpected section name.
>The (.[number]+) following section name are ld generated and not expected.
> Did you forget to use "ax"/"aw" in a .S file?
> Note that for example <linux/init.h> contains
> section definitions for use in .S files.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix following warnings:
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0x9c): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.iowa_register_bus()
WARNING: arch/powerpc/platforms/cell/built-in.o(.devinit.text+0xa4): Section mismatch in reference from the function .cell_setup_phb() to the function .init.text:.io_workaround_init()
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With CONFIG_VIRT_CPU_ACCOUNTING disabled, I got the following error:
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c: In function 'spu_switch_log_notify':
linux-2.6/arch/powerpc/platforms/cell/spufs/file.c:2542: error: implicit declaration of function 'get_tb'
make[4]: *** [arch/powerpc/platforms/cell/spufs/file.o] Error 1
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes vmemmap to use a different region (region 0xf) of the
address space, and to configure the page size of that region
dynamically at boot.
The problem with the current approach of always using 16M pages is that
it's not well suited to machines that have small amounts of memory such
as small partitions on pseries, or PS3's.
In fact, on the PS3, failure to allocate the 16M page backing vmmemmap
tends to prevent hotplugging the HV's "additional" memory, thus limiting
the available memory even more, from my experience down to something
like 80M total, which makes it really not very useable.
The logic used by my match to choose the vmemmap page size is:
- If 16M pages are available and there's 1G or more RAM at boot,
use that size.
- Else if 64K pages are available, use that
- Else use 4K pages
I've tested on a POWER6 (16M pages) and on an iSeries POWER3 (4K pages)
and it seems to work fine.
Note that I intend to change the way we organize the kernel regions &
SLBs so the actual region will change from 0xf back to something else at
one point, as I simplify the SLB miss handler, but that will be for a
later patch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
If victim (not ctx) is in spu_run, add victim to rq.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Use a TS_RESTORE_SIGMASK
lmb: Make lmb debugging more useful.
lmb: Fix inconsistent alignment of size argument.
sparc: Fix mremap address range validation.
Add a common hex array in hexdump.c so everyone can use it.
Add a common hi/lo helper to avoid the shifting masking that is
done to get the upper and lower nibbles of a byte value.
Pull the pack_hex_byte helper from kgdb as it is opencoded many
places in the tree that will be consolidated.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.
This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.
It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
acpi_unregister_gsi() should "undo" what acpi_register_gsi() does.
On systems that have legacy interrupts, acpi_unregister_gsi erroneously calls
iosapci_unregister_intr() which is wrong to do and causes a loud warning.
acpi_unregister_gsi() should just return in these cases.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is only palinfo_handle_smp as (indirect) user of palinfo_smp_call (by
way of smp_call_function_single) and surely palinfo_handle_smp never pass
NULL as parameter for info.
Signed-off-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a typo, and coding style cleanups for pfm_handle_work().
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch does:
- make comment at next to resched check more robust
- move "re-check" comments to next to where change predicate regs
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[Bug-fix for "[BUG?][2.6.25-mm1] sleeping during IRQ disabled"]
This patch does:
- enable interrupts before calling schedule() as same as others, ex. x86
- enable interrupts during ia64_do_signal() and ia64_sync_krbs()
- do_notify_resume_user() is still called with interrupts disabled, since
we can take short path of fsys_mode if-statement quickly.
- pfm_handle_work() is also called with interrupts disabled, since
it can deal interrupt mask within itself.
- fix/add some comments/notes
Reported-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sequence executed in check_sal_cache_flush:
- pend a timer interrupt
- call SAL_CACHE_FLUSH
- see if interrupt is still pending
can hang HP machines with buggy SAL_CACHE_FLUSH implementations.
Provide a kernel command-line argument to allow users skip this
check if desired. Using this parameter will force ia64_sal_cache_flush
to call ia64_pal_cache_flush() instead of SAL_CACHE_FLUSH.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some IA64 machines map all cell-local memory above 4 GB (32 bit limit).
However, in most cases, the kernel needs some memory below that limit that is
DMA-capable. So in this machine configuration, the crashkernel will be reserved
above 4 GB.
For machines that use SWIOTLB implementation because they lack an I/O MMU
the low memory is required by the SWIOTLB implementation. In that case,
it doesn't make sense to reserve the crashkernel at all because it's unusable
for kdump.
A special case is the "hpzx1" machine vector. In theory, it has a I/O MMU, so
it can be booted above 4 GB. However, in the kdump case that is not possible
because of changeset 51b58e3e26:
On HP zx1 machines, the 'machvec=dig' parameter is needed for the kdump
kernel to avoid problems with the HP sba iommu. The problem is that during
the boot of the kdump kernel, the iommu is re-initialized, so in-flight DMA
from improperly shutdown drivers causes an IOTLB miss which leads to an
MCA. With kdump, the idea is to get into the kdump kernel with as little
code as we can, so shutting down drivers properly is not an option.
The workaround is to add 'machvec=dig' to the kdump kernel boot parameters.
This makes the kdump kernel avoid using the sba iommu altogether, leaving
the IOTLB intact. Any ongoing DMA falls harmlessly outside the kdump
kernel. After the kdump kernel reboots, all devices will have been
shutdown properly and DMA stopped.
This patch pushes that functionality into the sba iommu initialization
code, so that users won't have to find the obscure documentation telling
them about 'machvec=dig'.
This means that also for hpzx1 it's not possible to boot when all
memory is above the 4 GB limit. So the only machine vectors that can handle
this case are "sn2" and "uv".
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds the basic IA64 machvec infrastructure to support
the SGI "UV" platform.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
ACPI/PCI: another multiple _OSC memory leak fix
x86/PCI: X86_PAT & mprotect
PCI: enable nv_msi_ht_cap_quirk for ALi bridges
PCI: Make the intel-iommu_wait_op macro work when jiffies are not running
ACPI/PCI: handle multiple _OSC
ACPI/PCI: handle multiple _OSC
x86/PCI: fix broken ISA DMA
PCI ACPI: fix uninitialized variable in __pci_osc_support_set
The user_regset_view table for the 32-bit regsets on the 64-bit build had
the wrong sizes for the FP regsets. This bug had no user-visible effect
(just on kernel modules using the user_regset interfaces and the like).
But the fix is trivial and risk-free.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix this warning:
arch/x86/mm/pat.c: In function `phys_mem_access_prot_allowed':
arch/x86/mm/pat.c:558: warning: long long unsigned int format, long
unsigned int arg (arg 6)
arch/x86/mm/pat.c: In function `map_devmem':
arch/x86/mm/pat.c:580: warning: long long unsigned int format, long
unsigned int arg (arg 6)
Signed-off-by: D Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this symbol export problem:
Building modules, stage 2.
MODPOST 193 modules
ERROR: "csum_partial" [fs/reiserfs/reiserfs.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
This is due to a known weakness of symbol exports: if a symbol's
only in-core user is an EXPORT_SYMBOL from a lib-y section, the
symbol is not linked in.
The solution is to move the export to x8664_ksyms_64.c - but the real
solution would be to fix kbuild.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/setup_64.c:954: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After resume on a 2cpu laptop, kernel builds collapse with a sed hang,
sh or make segfault (often on 20295564), real-time signal to cc1 etc.
Several hurdles to jump, but a manually-assisted bisect led to -rc1's
d2bcbad5f3 x86: do not zap_low_mappings
in __smp_prepare_cpus. Though the low mappings were removed at bootup,
they were left behind (with Global flags helping to keep them in TLB)
after resume or cpu online, causing the crashes seen.
Reinstate zap_low_mappings (with local __flush_tlb_all) for each cpu_up
on x86_32. This used to be serialized by smp_commenced_mask: that's now
gone, but a low_mappings flag will do. No need for native_smp_cpus_done
to repeat the zap: let mem_init zap BSP's low mappings just like on UP.
(In passing, fix error code from native_cpu_up: do_boot_cpu returns a
variety of diagnostic values, Dprintk what it says but convert to -EIO.
And save_pg_dir separately before zap_low_mappings: doesn't matter now,
but zapping twice in succession wiped out resume's swsusp_pg_dir.)
That worked well on the duo and one quad, but wouldn't boot 3rd or 4th
cpu on P4 Xeon, oopsing just after unlock_ipi_call_lock. The TLB flush
IPI now being sent reveals a long-standing bug: the booting cpu has its
APIC readied in smp_callin at the top of start_secondary, but isn't put
into the cpu_online_map until just before that unlock_ipi_call_lock.
So native_smp_call_function_mask to online cpus would send_IPI_allbutself,
including the cpu just coming up, though it has been excluded from the
count to wait for: by the time it handles the IPI, the call data on
native_smp_call_function_mask's stack may well have been overwritten.
So fall back to send_IPI_mask while cpu_online_map does not match
cpu_callout_map: perhaps there's a better APICological fix to be
made at the start_secondary end, but I wouldn't know that.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some versions of X used the mprotect workaround to change caching type from UC
to WB, so that it can then use mtrr to program WC for that region [1]. Change
the mmap of pci space through /sys or /proc interfaces from UC to UC_MINUS.
With this change, X will not need to use mprotect workaround to get WC type
since the MTRR mapping type will be honored.
The bug in mprotect that clobbers PAT bits is fixed in a follow on patch. So,
this X workaround will stop working as well.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rene Herman reported:
> commit 8779f2fc3b
>
> "x86: don't try to allocate from DMA zone at first"
>
> breaks all of ISA DMA. Or all of ALSA ISA DMA at least. All
> ISA soundcards are silent following that commit -- no error
> messages, everything appears fine, just silence.
That patch is buggy. We had an implicit assumption that
dev = NULL for ISA devices that require 24bit DMA.
The recent work on x86 dma_alloc_coherent() breaks the ISA DMA buffer
allocation, which is represented by "dev = NULL" and requires 24bit
DMA implicitly.
Bisected-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Include the missing kcrctab and kcrctab_unused sections into the m68knommu
linker script.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PA-RISC to aid debugging prints out the zonelists setup by the system. A
bad call to node_zonelist() breaks at compile-time. This patch fixes it.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This would appear to be the last reference to TOPDIR in the entire tree, after
which i'm guessing that variable can be dropped.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the subject says this patch adds the support for kernel preemption on
m68knommu Coldfire. I thing the same changes could be applied to 68360 &
68328 but since I don't have the HW, I don't touch it. Kconfig enables the
preemption item only on coldfire.
This is a missing chunk from Sebastian's original patch that I lost from the
first submission.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alarm delivery could be noticably late in the !CONFIG_NOHZ case because lost
ticks weren't being taken into account. This is now treated more carefully,
with the time between ticks being calculated and the appropriate number of
ticks delivered to the timekeeping system.
Cc: Nix <nix@esperi.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Give random.c a style workover while I'm changing it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The random driver would essentially hang if the host's /dev/random returned
-EAGAIN. There was a test of need_resched followed by a schedule inside the
loop, but that didn't help and it's the wrong way to work anyway.
The right way is to ask for an interrupt when there is input available from
the host and handle it then rather than polling.
Now, when the host's /dev/random returns -EAGAIN, the driver asks for a wakeup
when there's randomness available again and sleeps. The interrupt routine
just wakes up whatever processes are sleeping on host_read_wait.
There is an atomic_t, host_sleep_count, which counts the number of processes
waiting for randomness. When this reaches zero, the interrupt is disabled.
An added complication is that async I/O notification was only recently added
to /dev/random (by me), so essentially all hosts will lack it. So, we use the
sigio workaround here, which is to have a separate thread poll on the
descriptor and send an interrupt when there is input on it. This mechanism is
activated when a process gets -EAGAIN (activating this multiple times is
harmless, if a bit wasteful) and deactivated by the last process still
waiting.
The module name was changed from "random" to "hw_random" in order for udev to
recognize it.
The sigio workaround needed some changes. sigio_broken was added for cases
when we know that async notification doesn't work. This is now called from
maybe_sigio_broken, which deals with pts devices.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The top of physical memory should be below the initial process stack, not the
top of the address space, at least for as long as the stack isn't known to the
kernel VM system and appropriately reserved.
Cc: "Christopher S. Aker" <caker@theshore.net>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch includes page.h header into linker scripts that allow us to
use PAGE_SIZE macro instead of numeric constant.
To be able to include page.h into linker scripts page.h is needed for
some modification - i.e. we need to use __ASSEMBLY__ and _AC macro
[jdike@linux.intel.com - fixed conflict with as-layout.h]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I just saw similar patches in the janitor kernel's list, and spotted place it
fits.
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the BLOCK dependency for RAW_DRIVER, to match what's in
drivers/char/Kconfig. Also, while we're there, update the alleged
obsolesence of RAW_DRIVER since it doesn't seem to be going away any
time soon.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Robert P. J. Day <rpjday@crashcourse.ca>
Use newer, non-deprecated __SPIN_LOCK_UNLOCKED macro.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UML's supposed nanosecond clock interacts badly with NTP when NTP
decides that the clock has drifted ahead and needs to be slowed down.
Slowing down the clock is done by decrementing the cycle-to-nanosecond
multiplier, which is 1. Decrementing that gives you 0 and time is
stopped.
This is fixed by switching to a microsecond clock, with a multiplier
of 1000.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reintroduce uml_kmalloc for the benefit of UML libc code. The
previous tactic of declaring __kmalloc so it could be called directly
from the libc side of the house turned out to be getting too intimate
with slab, and it doesn't work with slob.
So, the uml_kmalloc wrapper is back. It calls kmalloc or whatever
that translates into, and libc code calls it.
kfree is left alone since that still works, leaving a somewhat
inconsistent API.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error returns are negative.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tidy the ptrace interface code. Removed a bunch of unused macros.
Started converting register sets from arrays of longs to structures.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few random style fixes.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Redo how host capabilities are recorded at startup and disabled on the
command line.
There are now explicit variables saying what's been disabled by the
command line rather than the implicitness of the have_* variable being
zero. The capability variables now start at zero and are set to one
as their capabilities are found to be present on the host.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Cc: "Nelson, Shannon" <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DIU platform code should not just write to the PIXIS' BRDCFG0 register,
it should set and clear its own bits only, otherwise it will break
firmware setup (in fact it breaks second uart).
Also get rid of magic numbers in the related code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8568 MDS needs some configuration changes to the PHY in order to
work properly. These are done in the firmware, normally, but Linux
shouldn't need to rely on the firmware running such things (someone
could disable the PHY support in the firmware to save space, for instance).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of current mainline tree, TULIP driver is unusable on MPC8610HPCD
boards. There is a patch[1] floating around (and also included in the
BSP), which tries to heal the situation, though the ethernet is still
unusable. Practically it takes ages to mount NFS filesystem:
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 180k init
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
So, instead of trying to add uli526x functionality into TULIP driver
(which is already bloated enough), I fixed existing ULI526X driver
and now it works perfectly well here.
[1] http://www.bitshrine.org/gpp/0024-MPC8610-ETH-Lyra-native-ethernet.txt
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- move all kconfig board settings into board resources
- fixup casting style according to lkml feedback
- rewrite driver so that it can handle arbitrary
of instances according to the declared platform resources
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Just like mmap, we need to validate address ranges regardless
of MAP_FIXED.
sparc{,64}_mmap_check()'s flag argument is unused, remove.
Based upon a report and preliminary patch by
Jan Lieskovsky <jlieskov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow linker to catch sections overlapping we have to declare
them in appropriate order.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The phys_cpu_present_map is an expected symbol in the SMP harness.
Unfortunately, x86 recently moved this and a few others to
kernel/setup.c where it doesn't quite work because voyager has to
define its own. Use CONFIG_X86_LOCAL_APIC to isolate these
definitions and fix up another area in setup.c where CONFIG_X86_SMP
should be used instead of CONFIG_SMP.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: toralf.foerster@gmx.de
Cc: Mike Travis <travis@sgi.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rene Herman reported:
> commit 8779f2fc3b
>
> "x86: don't try to allocate from DMA zone at first"
>
> breaks all of ISA DMA. Or all of ALSA ISA DMA at least. All
> ISA soundcards are silent following that commit -- no error
> messages, everything appears fine, just silence.
That patch is buggy. We had an implicit assumption that
dev = NULL for ISA devices that require 24bit DMA.
The recent work on x86 dma_alloc_coherent() breaks the ISA DMA buffer
allocation, which is represented by "dev = NULL" and requires 24bit
DMA implicitly.
Bisected-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes the following build errror caused by
commit 7dffa3c673
(ntp: handle leap second via timer):
<-- snip -->
...
CC arch/mips/emma2rh/markeins/setup.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/emma2rh/markeins/setup.c:79: error: conflicting types for 'clock'
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/clocksource.h:96: error: previous declaration of 'clock' was here
make[2]: *** [arch/mips/emma2rh/markeins/setup.o] Error 1
<-- snip -->
[Ralf: reformated to 80 colums after the fix and marked emma2rh_clock as
__initdata]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- using simple_strtol() where strict_strtol() could be used.
In addition to these changes, also do the following:
- remove needless parentheses;
- remove unneeded numeric literal type cast;
- insert spaces between operator and its operands;
- remove excess new lines;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the structure initializer;
- fix typos, capitalize acronyms, etc. in the comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix many errors and warnings given by checkpatch.pl:
- space after opening and before closing parentheses;
- use of C99 // comments;
- leading spaces instead of tabs;
- brace not on the same line with 'else' in the 'if' statement;
statement;
- printk() without KERN_* facility level;
- using simple_strtol() where strict_strtol() could be used.
- including <asm/gpio.h> instead of <linux/gpio.h>.
In addition to these changes, also do the following:
- insert spaces between operator and its operands;
- replace tab between the function type and name with space in
mtx1_pci_idsel() declaration;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the array/structure
initializers;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- initialization of a 'static' variable to 0;
- space after opening and before closing parentheses;
- missing space between 'for' and opening parenthesis;
- macros with complex values not enclosed in parentheses;
- printk() without KERN_* facility level;
- unnecessary braces for single-statement block;
- using simple_strtol() where strict_strtol() could be used;
- line over 80 characters.
In addition to these changes, also do the following:
- mention DBAu1200 board in the Makefile;
- replace the group of #include/#ifdef directives by a single
#include <au1xxx.h> since this header contains the needed stuff;
- properly indent the blocks;
- insert spaces between operator and its operands, remove excess spaces
there;
- remove needless parentheses and add some for clarity;
- replace numeric literals/expressions with the matching macros;
- remove space after the type cast's closing parenthesis;
- reduce pb1200_setup_cascade() to the single 'return' statement;
- reduce the number of printed empty lines in the so-called CPLD
workaround;
- remove #undef AU1X00_EXTERNAL_INT since that macro is not defined
anywhere;
- replace spaces after the macro name with tabs in the #define directives;
- remove excess tabs after the macro name in the #define directives;
- fix typo in the BCSR_RESETS_PWMR1mUX macro's name;
- group all Pb1200 PCMCIA definitions together;
- put the function's result type and name/parameters on the same line;
- insert missing and remove excess new lines;
- make the multi-line comment style consistent with the kernel style
elsewhere by adding empty first line and/or adding space/asterisk on
their left side;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- combine some comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
