We need to keep building sigframes until no pending signals remain.
Wrap do_notify_resume() calls into loops; do _not_ allow syscall
restart logics to trigger after the first iteration.
Incidentally, comments about pending signals that should (somehow)
be in r18 are pure BS. Doesn't work that way and cannot work that
way, sorry...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
solution a-la arm one - pick a callee-saved register (r30), set it
non-zero when entering a syscall, have sigreturn wrapper zero it out
and pass the value in it to do_notify_resume() as "in_syscall" (actually,
"restarts allowed") argument.
Note that we don't give a damn about ret_from_fork() - return value
is not restart-worthy anyway.
Possible remaining bug: on !MMU we still have _debug_exception()
restartable. If it hits with -ERESTART_... accidentally in r3, fun happens.
MMU does _not_ have _debug_exception() restartable. If that's decided to
be a bug (as I strongly suspect it to be), we'll just need to replace
setting r30 to 1 with setting r30 to 0 in !MMU _debug_exception().
Up to microblaze maintainers...
[folded a fix from Michal]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull microblaze changes from Michal Simek.
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Setup correct pointer to TLS area
microblaze: Add TLS support to sys_clone
microblaze: ftrace: Pass the first calling instruction for dynamic ftrace
microblaze: Port OOM changes to do_page_fault
microblaze: Do not select GENERIC_GPIO by default
Formerly unused Args 4/5 now load parent tid / child tid so the brid to
do_fork can pick up TLS from r10. Arg 3 still unused
There is also necessary to fix old glibc which do not setup r9/r10 (arg 4/5).
Simple clearing them is fine.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: David Holsgrove <david.holsgrove@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Reset vector can be setup by bootloader and kernel doens't need
to touch it. If you require to setup reset vector, please use
CONFIG_MANUAL_RESET_VECTOR throught menuconfig.
It is not possible to setup address 0x0 as reset address because
make no sense to set it up at all.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: John Williams <john.williams@petalogix.com>
If soft reset falls through with no hardware assisted reset, the best
we can do is jump to the reset vector and see what the bootloader left
for us.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: John Williams <john.williams@petalogix.com>
Microblaze vector table stores several vectors (reset, user exception,
interrupt, debug exception and hardware exception).
All these functions can be below address 0x10000. If they are, wrong
vector table is genarated because jump is not setup from two instructions
(imm upper 16bit and brai lower 16bit).
Adding specific offset prevent problem if address is below 0x10000.
For this case only brai instruction is used.
Signed-off-by: Michal Simek <monstr@monstr.eu>
"la" pseudo instruction is only translation to "addik".
Use directly "addik" which is described in the MB reference guide.
Signed-off-by: Michal Simek <monstr@monstr.eu>
r0_ram pool was used for saving/restoring register
content if hw exception happen. This poll was replaced by
pt_pool_space with PT_SIZE size.
Based on this change SAVE_STATE_ARG_SPACE was removed which
caused that PTO offset is zero that's why is also removed.
r0_ram space was used as scratchpad by v850. In early
Microblaze Linux developing phase was this part of code
blindly copied.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This reverts commit 0e41c90908.
Break jffs2 rootfs because the patch removes syscall calling
from kernel space.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signal code uses r3 value which saved in restore_sigcontext to
rt_sigframe but it require to be zeroed. If is not zero rt_sigframe
contains wrong values.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Do not save return registers before rt_sigreturn is called.
_user_exception(syscall handler) already setup return address
that's why it is removed from rt_sigreturn_wrapper.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Kgdb uses brki r16, 0x18 instruction to call
low level _debug_exception function which save
current state to pt_regs and call microblaze_kgdb_break
function. _debug_exception should be called only from
the kernel space. User space calling is not supported
because user application debugging uses different handling.
pt_regs_to_gdb_regs loads additional special registers
which can't be changed
* Enable KGDB in Kconfig
* Remove ancient not-tested KGDB support
* Remove ancient _debug_exception code from entry.S
Only MMU KGDB support is supported.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Jason Wessel <jason.wessel@windriver.com>
CC: John Williams <john.williams@petalogix.com>
CC: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
CC: linux-kernel@vger.kernel.org
Acked-by: Jason Wessel <jason.wessel@windriver.com>
This is the first patch which add support for
user application debugging through brki rX, 0x18 vector.
This patch has side effect which also remove security issue
to use brki rX, 0x18 to freeze kernel.
Support for old gdb support via priviledged exception
(brk r0, r0) is still there. It will be remove in future.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Syscall can be called only from userspace that's why
we don't need to check which space kernel come from.
Kernel syscall calling is not check and shouldn't come
throught this part of code.
Signed-off-by: Michal Simek <monstr@monstr.eu>
We are not working with values from MSR that's why
we can discard it and use r11 for different purpose without
saving/restoring.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Remove set_vms because UMS is cleared and VMS is already setup.
Optimize function calling which save one additional instruction.
Signed-off-by: Michal Simek <monstr@monstr.eu>
VMS is always setup because VM mode was before
exception/syscall/interrupt. Kernel continues in kernel mode
that's why we have to clear UMS bit if kernel comes from
user space.
Signed-off-by: Michal Simek <monstr@monstr.eu>
PT_MODE stores information if kernel comes from user
or kernel space. If come from user space, PT_MODE
contains 0. If come from kernel store, PT_MODE contains
non zero value. We don't need to save value 1. I am using
r1 register which contains non zero value.
This change save one additional instruction.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Keep together all arguments for send_sig function.
Move returning address to delay slot which is executed.
Remove additional send_sig loading. I am using IMM part of
rtbd instruction with r0.
old solution:
addik r11, r0, send_sig
rtbd r11, 0
nop
new solution:
rtbd r0, send_sig
nop
There is one instruction saving.
Signed-off-by: Michal Simek <monstr@monstr.eu>
It is necessary to setup BIP and EE and clear EIP
only for unaligned exception handler. The rest of
hw exception handlers don't require it.
HW exception occured and we are not in virtual mode.
That's why we can do operations protected by EIP.
Interrupt, next hw exception or syscall can't occur.
EIP is cleared by rted.
This change speedup page_fault hw exception handler
which is critical path.
There is also necessary to save R11 content before
flag setup for unaligned exception.
Signed-off-by: Michal Simek <monstr@monstr.eu>
SAVE_STATE macro is used in hw exceptions high level handling
functions. Hw exception doesn't disable IRQ that's why we don't
need to reenable it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
We don't need to protect by BIP whole ret_from_trap/ret_from_exc code.
Only restoring from user/hw exception should be covered.
If BIP is setup, IRQ can't occur.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is a way howto remove Kernel Mode variable. It is easier
to parse UMS bit in MSR to find out if I come from kernel or user
space. Loading MSR content should be in one cycle and loading
PER_CPU variable depends on memory state.
Signed-off-by: Michal Simek <monstr@monstr.eu>
