atl2_xmit_frame() should call dev_consume_skb_any() when the
transmission is successful. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN743x includes on chip One-Time-Programmable (OTP) memory.
This patch extends the ethtool EEPROM read/write interface to
access OTP memory space.
The currently existing interface is limited, as it does not
allow OTP read, and OTP writes are restricted to
offset==0, length==512, and data[0]==0xF3.
This patch removes these restrictions and adds a private flag
called OTP_ACCESS, which is used to switch between EEPROM, and
OTP modes.
The private flag OTP_ACCESS is configurable through the
ethtool --set-priv-flags command.
And visible through the
ethtool --show-priv-flags command.
By default OTP_ACCESS is false, and there for previously existing
EEPROM commands will work exactly the same. However now access to
OTP requires one extra step of setting OTP_ACCESS to true. This
flag controls the read, write, and length reporting, functions
of ethtool.
EEPROM presence is not checked when setting or clearing this flag.
If the EEPROM is not present, the user, as before, will need to
diagnose that using existing read and write function of ethtool,
while OTP_ACCESS is false.
Updates for V2:
Added comments as to why this patch is needed.
Added comments explaining that EEPROM presence is not check
when setting or clearing the OTP_ACCESS flag.
Added length checking to all otp/eeprom read/write functions.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF can receive packets of other functions when in promisc
mode. It's not safe, so don't allow VF to enable promisc
mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initialization for nic state, sets flag
HNS3_NIC_STATE_DOWN when initialize, clears it before
vectors and napi being enabled in the hns3_nic_net_up(),
and sets it back in the error handler.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single transmit packet can span up to 8 descriptors according
to the HW limit. If a skb has more than 8 frags, driver uses
skb_copy to get a new skb which has less frags.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_client_setup_tc in enet is for updating TC configuration to
stack, and hclge_setup_tc in hclge_dcb is mainly for setting the
configuration to hardware.
This patch removes the hns3_nic_set_real_num_queue from
hns3_setup_tc in enet, and call hclge_client_setup_tc to update
TC configuration to stack with netdev down, because the netdev
down operation is done in hclge_dcb now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After doing down/uninit/init/up in hclge_dcb, it is not necessary
to call dcb_ops->map_update in enet, so hclge_map_update can be
called directly in hclge_dcb.
This is for preparing to call hns3_nic_set_real_num_queue with
netdev down when user changes mqprio configuration.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user changes the mqprio configuration, enet need to be
uninited and inited besides down'ed and up'ed, because the queue
num may change when the TC num changes.
Also, it is more suitable to do the down/unint/init/up operation
in hclge module using hclge_notify_client, because this config
change may affect PF and its VF.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After setting the serdes loopback, you need to determine
the status of the MAC negotiation. If a status exception
is obtained after 200ms, a timeout error is returned.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, vlan filter is always bypassed when enable
broadcast promisc mode. In this case, broadcast packets with
any vlan id can be accpeted. We should disable broadcast promisc
mode until user want enable it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current code, it always return 0, even loopback mode setting failed.
It's incorrect. This patch fixes return value handle for loopback test.
Fixes: 0f29fc23b2 ("net: hns3: Fix for loopback selftest failed problem")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hclge_ieee_setets returns error directly when there is
error, which may cause netdev not up problem.
This patch adds some error handling when setting ETS configuration
fails.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unload hns3 driver, we should clear the pci private data.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet statistics for netdev should not include the packets dropped
by hardware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EEE support for RTL8168f to the recently added EEE handling
framework in the driver. This patch leaves the chip defaults, means
EEE typically is disabled initially and it's up to the user to enable
it via ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable EEE per default on chip versions from RTL8168g.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the general framework to deal with EEE in this driver
plus EEE support for chip versions from RTL8168g. We don't touch the
default chip settings, therefore EEE will usually be disabled and it's
up to the user to enable it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Representors software stats are basic, this patch is reusing the
mlx5e_fold_sw_stats in representors, which sums up the basic stats64 for a
mlx5e netdevice.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This behavior is already adopted for all other cases in the cited patch.
The representor's functions were missed, here we modify the them to
behave similarly.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5e_grp_sw_update_stats can be called from two threads,
1) ndo_get_stats64
2) get_ethtool_stats
For this reason and to minimize concurrency issue impact on 64bit machines
mlx5e_grp_sw_update_stats folds the software stats into a temporary
variable then copies it to the global driver stats, both ethtool and ndo
statistics callbacks will use the global software stats variable to report
whatever stats they need.
Actually ndo_get_stats64 doesn't need to fold the whole software stats
(mlx5e_grp_sw_update_stats), all it needs is five counters to fill the
rtnl_link_stats64 relevant stats parameter.
Hence this patch introduces a simpler helper function to fold software
stats for ndo_get_stats64 which will work directly on rtnl_link_stats64
stats parameter and not on the global or even temporary mlx5e_sw_stats
variable.
Since now mlx5e_grp_sw_update_stats is not called by ndo_get_stats64 we
can make it static and remove the temp var.
Unlike mlx5e_grp_sw_update_stats the new fold stats function doesn't
need to zero out the output statistics parameter since it is already
done by the stack @dev_get_stats().
This patch is fixing stack usage of mlx5e_grp_sw_update_stats on
x86 gcc-4.9 and higher, the concurrency issue between mlx5's
ndo_get_stats64 and get_ethtool_stats is resolved as well.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We were not tracking flow tables so far, add it up.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This confusing construction confuses the compiler which can't see
that flow is initialized if !err:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function `mlx5e_configure_flower`
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:2727:28: warning:
`flow` may be used uninitialized in this function
[-Wmaybe-uninitialized]
There is no reason for two function outputs, just return the
pointer directly and use ERR_PTR to encode a failure.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we have one cpu in XPS cpumask per tx queue, this is good
enough for default configuration where there is a tx queue per cpu.
However, once configuration changes to use less tx queues, part of the
cpus are not XPS-mapped and so the select queue decision falls back to
hash calculation and balancing is not guaranteed.
Expand XPS cpumask to enable using all cpus even when number of tx
queues is smaller than number of cpus.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Only the Receive CQ makes use of these fields. Take them
out into a separate struct and save space in the generic
CQ structure.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the non-linear SKB memory scheme of Striding RQ, a packet header
could cross page boundary. This requires special care in fast path
that costs LoC, additional runtime instructions and branches.
It could happen when the header (up to 256B) does not fit in
a single stride. Avoid this by working with a stride size that fits
the maximum possible header. Stride is increased form 64B to 256B.
Performance:
Tested packet rate for UDP streams, single ring, on ConnectX-5.
Configuration:
Set Striding RQ and LRO ON (to enabled the non-linear SKB scheme).
GRO OFF, early drop by TC rule.
64B: 4x worse memory utilization, no page-crossers headers
- No degradation (5,887,305 pps).
- The reduction in memory utilization is compensated by the saving of
branches tests.
192B: 1.33x worse memory utilization, avoid page-crossers headers
- Before: 5,727,252. After: 5,777,037. ~1% gain.
256B: Same memory util, no page-crossers
- Before: 5,691,885. After: 5,748,007. ~1% gain.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Few chip versions use the same sequence to adjust 10M and ALDPS, so
let's factor it out. This patch also fixes a (most likely) typo in
rtl8168g_1_hw_phy_config. There bit 8 in reg 0x14 on page 0x0bcc
was set and not cleared. According to the vendor driver this bit
needs to be cleared in all cases.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip versions from RTL8168g onward use the same sequence to disable
ALDPS (Advanced Link-Down Power Saving). So let's factor this out.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_clk_get() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two statements are incorrecly indented, fix these by removing a space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A ternary match table is used for RFS. If multiple entries in the table
match, the entry with the lowest numerical values index is chosen as the
matching entry. Entries in the table are identified using an index
which takes a value from 0 to PRFSCAPR[NUM_RFS]-1 when accessed by the
PSI (PF).
Portions of the RFS table can be assigned to each SI by the PSI (PF)
driver in PSIaRFSCFGR. Assignments are cumulative, the entries assigned
to SIn start after those assigned to SIn-1. The total assignments to
all SIs must be equal to or less than the number available to the port
as found in PRFSCAPR.
For RSS, the Toeplitz hash function used requires two inputs, a 40B
random secret key that is supplied through the PRSSKR0-9 registers as well
as the relevant pieces of the packet header (n-tuple). The 6 LSB bits of
the hash function result will then be used as a pointer to obtain the tag
referenced in the 64 entry indirection table. The result will provide a
winning group which will be used to help route the received packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSIs (VFs) may send a message to the PSI (PF) for general notification
or to gain access to hardware resources which requires host inspection.
These messages may vary in size and are handled as a partition copy
between two memory regions owned by the respective participants.
The PSI will respond with fail or success and a 16-bit message code.
The patch implements the vf to pf messaging mechanism above and, as the
first application making use of this support, it enables the VF to
configure its own primary MAC address.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds most h/w statistics counters: non-privileged SI conters, as
well as privileged Port and MAC counters available only to the PF.
Per ring software stats are also included.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC is a multi-port virtualized Ethernet controller supporting GbE
designs and Time-Sensitive Networking (TSN) functionality.
ENETC is operating as an SR-IOV multi-PF capable Root Complex Integrated
Endpoint (RCIE). As such, it contains multiple physical (PF) and
virtual (VF) PCIe functions, discoverable by standard PCI Express.
Introduce basic PF and VF ENETC ethernet drivers. The PF has access to
the ENETC Port registers and resources and makes the required privileged
configurations for the underlying VF devices. Common functionality is
controlled through so called System Interface (SI) register blocks, PFs
and VFs own a SI each. Though SI register blocks are almost identical,
there are a few privileged SI level controls that are accessible only to
PFs, and so the distinction is made between PF SIs (PSI) and VF SIs (VSI).
As such, the bulk of the code, including datapath processing, basic h/w
offload support and generic pci related configuration, is shared between
the 2 drivers and is factored out in common source files (i.e. enetc.c).
Major functionalities included (for both drivers):
MSI-X support for Rx and Tx processing, assignment of Rx/Tx BD ring pairs
to MSI-X entries, multi-queue support, Rx S/G (Rx frame fragmentation) and
jumbo frame (up to 9600B) support, Rx paged allocation and reuse, Tx S/G
support (NETIF_F_SG), Rx and Tx checksum offload, PF MAC filtering and
initial control ring support, VLAN extraction/ insertion, PF Rx VLAN
CTAG filtering, VF mac address config support, VF VLAN isolation support,
etc.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soften the memory barrier call of mb() by a sufficient wmb() in the
consumer index update of the event queues.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far member rtl_fw has three states:
- IS_ERR(rtl_fw): firmware not loaded
- !rtl_fw: no firmware available
- other: firmware loaded
This can be made simpler and clearer by adding the firmware name as
member fw_name to struct rtl8169_private. Then:
- !fw_name: no firmware available
- !rtl_fw: firmware not loaded
- rtl_fw: firmware loaded
This change also allows to easily merge rtl_request_uncached_firmware
into rtl_request_firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFC enabling is based on user priority, currently it is
based on TC, which may cause PFC not setting correctly when pri
to TC mapping is not one to one relation.
This patch adds pfc_en in tm_info to fix it.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old firmware version, statistics acquisition of
PFC frames and MAC control frames is not supported.
Add command retrieves statistics for PFC frames and
MAC control frames from the firmware.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the TC weight in SSU module according to
info in tm_info.
Also, zero weight of TC weight in SSU ETS module means enabling
strict priority, so do not allow zero weight when in ETS mode.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GE MAC does not support PFC, when driver is initializing and MAC
is in GE Mode, ignore the fw not supported error, otherwise
initialization will fail.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to firmware error code definition, the error code of 2
means NOT_SUPPORTED, this patch changes it to NOT_SUPPORTED.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Param pending_buf and skb may be not NULL when free ring.
This patch clears them when free ring.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 849e460776 ("net: hns3: add ethtool_ops.get_channels support for VF")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shaper setting does not change currently, when TC num changes,
which may cause shaper parameter not setting problem.
This patch fixes it by setting the shaper parameter when TC num
changes.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rss configuration set by user will be lost when setting
channel.
This patch fixes it by not setting rss configuration to default
if user has configured the rss.
Fixes: 09f2af6405 ("net: hns3: add support to modify tqps number")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In origin codes, there are some statistics item are got from mac, which
also include the packets statistics of VF. It is unreasonable. This
patch fixes it by counting them in the rx/tx processing flow.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx multicast packets statistic for each ring.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds calling roce callback function when link status
change.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
