Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set maximum transfer length per IO on RAID volumes to 4MB by setting
VD's queue's max_sector to 8192.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump mpt3sas driver version from 12.100.00.00 to 13.100.00.00
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified driver code to use scsi_prot_ref_tag() API instead of
scsi_get_lba(), while initializing reference tag field in the CDB.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"
This event is only for Intruder/Cutlass HBAs.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI version and MPI header files.
ChangeList:
* Added SATADeviceWaitTime to SAS IO Unit Page 4
* Added EEDPObservedValue added to SCSI IO Reply message
* Added MPI2_EVENT_ACTIVE_CABLE_EXCEPTION and
MPI26_EVENT_DATA_ACTIVE_CABLE_EXCEPT
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member. The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup". The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.
Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.
Fixes: 146b16c807 (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _base_make_ioc_operational(), we walk ioc->reply_queue_list and pull
a pointer out of successive elements of ioc->reply_post[] for each entry
in that list if RDPQ is enabled.
Since the code pulls the pointer for the next iteration at the bottom of
the loop, it triggers the a KASAN dump on the final iteration:
BUG: KASAN: slab-out-of-bounds in _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas] at addr ffff880754816ab0
Read of size 8 by task modprobe/305
<snip>
Call Trace:
[<ffffffff81dfc591>] dump_stack+0x4d/0x6c
[<ffffffff814c9689>] print_trailer+0xf9/0x150
[<ffffffff814ceda4>] object_err+0x34/0x40
[<ffffffff814d1231>] kasan_report_error+0x221/0x530
[<ffffffff814d1673>] __asan_report_load8_noabort+0x43/0x50
[<ffffffffa0043637>] _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas]
[<ffffffffa0049a51>] mpt3sas_base_attach+0x1991/0x2120 [mpt3sas]
[<ffffffffa0053c93>] _scsih_probe+0xeb3/0x16b0 [mpt3sas]
[<ffffffff81ebd047>] local_pci_probe+0xc7/0x170
[<ffffffff81ebf2cf>] pci_device_probe+0x20f/0x290
[<ffffffff820d50cd>] really_probe+0x17d/0x600
[<ffffffff820d56a3>] __driver_attach+0x153/0x190
[<ffffffff820cffac>] bus_for_each_dev+0x11c/0x1a0
[<ffffffff820d421d>] driver_attach+0x3d/0x50
[<ffffffff820d378a>] bus_add_driver+0x44a/0x5f0
[<ffffffff820d666c>] driver_register+0x18c/0x3b0
[<ffffffff81ebcb76>] __pci_register_driver+0x156/0x200
[<ffffffffa00c8135>] _mpt3sas_init+0x135/0x1000 [mpt3sas]
[<ffffffff81000423>] do_one_initcall+0x113/0x2b0
[<ffffffff813caa5a>] do_init_module+0x1d0/0x4d8
[<ffffffff81273909>] load_module+0x6729/0x8dc0
[<ffffffff81276123>] SYSC_init_module+0x183/0x1a0
[<ffffffff8127625e>] SyS_init_module+0xe/0x10
[<ffffffff828fe7d7>] entry_SYSCALL_64_fastpath+0x12/0x6a
Fix this by pulling the value at the beginning of the loop.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jens Axboe <axboe@fb.com>
Acked-by: Chaitra Basappa <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling synchronize_irq() right before free_irq() is quite useless. On
one hand the IRQ can easily fire again before free_irq() is entered, on
the other hand free_irq() itself calls synchronize_irq() internally (in
a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Deallocate resources before reallocating of the same in retry_allocation
path of _base_allocate_memory_pools()
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed cpumask_clear as it is not required for zalloc_cpumask_var and
free free_cpumask_var before freeing reply_q.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump mpt3sas driver version from 09.102.00.00 to 12.100.00.00
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Track msix of each IO and use the same msix for issuing abort to timed
out IO. With this driver will process IO's reply first followed by TM.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI version and MPI header files.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support for configurable Chain Frame Size. Calculate the
Chain Message Frame size from the IOCMaxChainSegementSize (iocfacts).
Applicable only for mpt3sas/SAS3.0 HBA's.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Module parameter to enable/disable configuring affinity hint for msix
vector. SMP affinity feature can be enabled/disabled by setting module
parameter "smp_affinity_enable" to 1/0. By default this feature is
enabled. (smp_affinity_enable = 1 enabled).
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver assumes HighPriority credit as part of Global credit. But,
Firmware treats HighPriority credit value and global cedits as two
different values. Changed host queue algorithm to treat global credits
and highPriority credits as two different values.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Never block the SEP device (i.e. Never invoke the
scsi_internal_device_block() API for SEP device) even for the delay not
responding events. Blocking the SEP device will create a deadlock while
adding any device to the OS.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1.Wrong size of argument is being passed
The size of struct being passed as an argument to memset func and area of
memory being pointed by an instance of struct in memset func should be of
same structure type.
2.Dereference null return value
3.Array compared against '0'
Check whether value pointed by particular index of an array is null or not
in "if" statement.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As driver was using MPI SGL while framing the SMP Passthrough request
message due to which firmware unable to post the Reply Data in the host
memory and timeout is observed for this SMP Passthrough request message
and so unable to perform phy disable operation.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated hardware description headers with MPI v2.6 and
mpt3sas_pci_table[] with vendor_ids, device_ids of Cutlass and Intruder
HBA which have support for 4 ports.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It might happen that we try to free an already freed pointer.
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The non-PCI builds of the O day test project are failing:
On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote:
> warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct
> dependencies (SCSI_LOWLEVEL && PCI && SCSI)
The problem is that select and depend don't interact because Kconfig doesn't
have a SAT solver, so depend picks up dependencies and select does onward
selects, but select doesn't pick up dependencies. To fix this, we need to add
the correct dependencies to the MPT2SAS option like this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: b840c3627b
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The mpt2sas driver was recently folded into mpt3sas to reduce code
duplication.
To avoid problems for people that only have CONFIG_SCSI_MPT2SAS in their
.config we introduce a dummy option that will select MPT3SAS if MPT2SAS
was previously enabled.
This is a temporary measure and we will deprecate this config option in
4.6.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
CC: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.
Actually in the driver code, driver is using below API's
1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.
but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After merging the scsi tree, today's linux-next build (powerpc
allyesconfig) failed like this:
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_io_done':
drivers/scsi/mpt3sas/mpt3sas_base.h:1414:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_get': function body not available
mpt3sas_scsi_direct_io_get(struct MPT3SAS_ADAPTER *ioc, u16 smid);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4448:6: error: called from here
if (mpt3sas_scsi_direct_io_get(ioc, smid) &&
^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
mpt3sas_scsi_direct_io_set(ioc, smid, 0);
^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:5
9:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
mpt3sas_scsi_direct_io_set(ioc, smid, 0);
^
Presumably caused by commit
c84b06a48c ("mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Bump mpt3sas driver version to 09.102.00.00
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.
* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.
* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
that, during the driver load time driver can use corresponding host
template(based the pci device ID) while registering a scsi host
adapter instance for that pci device.
* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
device processes only those ioctl cmds issued for the SAS3 HBAs.
* Added separate indexing for SAS2 and SAS3 HBAs.
* Replaced compile time check 'MPT2SAS_SCSI' to run time check
'hba_mpi_version_belonged' whereever needed.
* Aliased this merged driver to mpt2sas using MODULE_ALIAS.
* Moved global varaible 'driver_name' to per adapter instance variable.
* Created two raid function template and used corresponding raid
function templates based on the run time check
'hba_mpi_version_belonged'.
* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
renamed it as mpt3sas_warpdrive.c.
* Also renamed the functions in mpt3sas_warpdrive.c file to follow
current driver function name convention.
* Updated the Makefile to build mpt3sas_warpdrive.o file for these
WarpDrive-specific functions.
* Also in function mpt3sas_setup_direct_io(), used sector_div() API
instead of division operator (which gives compilation errors on 32 bit
machines).
* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.
* Added module parameter 'hbas_to_enumerate' which permits using this
merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
driver.
Here are the available options for this module parameter:
0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs
* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bump the mpt2sas driver version to 20.102.00.00 and
Bump the mpt3sas driver version to 9.101.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops
1. pci_access_mutex lock added to provide synchronization between IOCTL,
sysfs, PCI resource handling path
2. gioc_lock spinlock to protect list operations over multiple
controllers
This patch is ported from commit 6229b414b3 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added OEM Gen2 PnP ID branding names from mpt2sas driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.
Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.
This patch is ported from commit 008549f6e8 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.
Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.
This patch is ported from the following mpt2sas driver commit
d224fe0d60 ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs shost attribute called "BMR_status" is implemented to report
Backup Rail Monitor status.
This attribute is located in:
/sys/class/scsi_host/host#/BMR_status
When reading this adapter attribute, the driver will output the state of
GPIO[24]. It returns "0" if BMR is healthy and "1" for failure.
If it returns an empty string then it means that there was an error
while obtaining the BMR status. Check dmesg for what error has occurred.
This sysfs shost attribute is mainly for WarpDrive controllers.
This commit is a port of 6c265660c2 ("mpt2sas: Provide sysfs attribute
to report Backup Rail Monitor Status").
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ported the following list of WarpDrive-specific patches:
1. commit 0bdccdb0a0 ("mpt2sas: WarpDrive
New product SSS6200 support added")
2. commit 82a4525812 ("mpt2sas: WarpDrive
Infinite command retries due to wrong scsi command entry in MPI
message")
3. commit ba96bd0b1d ("mpt2sas: Support
for greater than 2TB capacity WarpDrive")
4. commit 4da7af9494 ("mpt2sas: Do not
retry a timed out direct IO for Warpdrive")
5. commit daeaa9df92 ("mpt2sas: Avoid type
casting for direct I/O commands").
Also set the mpt2_ioctl_iocinfo adapter_type to:
1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs
2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive
3. MPT2_IOCTL_INTERFACE_SAS2 for other Gen2 HBAs
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch stops the driver to invoke kthread (which remove the dead
ioc) for some time while EEH recovery has started.
This patch is a port of commit b4730fb6e5 ("mpt2sas: fix for driver
fails EEH, recovery from injected pci bus error")'.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Do not enable MSI-X vectors for SAS2008 B0 controllers
2. Enable a single MSI-X vector for the following controller:
a. SAS2004
b. SAS2008
c. SAS2008_1
d. SAS2008_2
e. SAS2008_3
f. SAS2116_1
g. SAS2116_2
3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
for Gen3 Invader/Fury C0 and above revision HBAs
4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
for all Intruder and Cutlass HBAs
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.
Also enable fast_path only for SAS3 HBAs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Gen2 HBAs use MPI scatter-gather lists whereas Gen3 HBAs use IEEE
scatter-gather lists. Modify the common code part in such a way that it
will build IEEE SGL tables for Gen3 HBAs and MPI SGL tables for Gen2
HBAs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently there is a logging level option provided for each of our
drivers in the kernel configuration utility. Users can enable this
option to get more verbose information. By default it is enabled.
Only when this option is enabled will the functions which display the
required information get compiled in.
As we are merging the both drivers we can no longer provide this
configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig
and unconditionally enable logging (by removing the #ifdef
CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all
functions which are defined to display more verbose information get
compiled in.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.
2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Create a mpt2sas_module.c file for mpt2sas where GEN2 HBA devices
register with PCI, SML, IOCTL subsystems.
2. Updated the Makefile to use the object files from mpt3sas folder.
3. Defined a compilation flag SCSI_MPT2SAS which can be used to not
include those sections of code from mpt3sas driver which are not
required for mpt2sas driver.
4. Inherited automatic diag buffer feature from mpt3sas driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Added mpt2sas driver related macros in mpt3sas header files
2. Made scsi host's, raid class', pci's, ioctl's callback functions
global so that both drivers can use them.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Issue: When the disks are getting discovered and assigned device
handles by the kernel, a device block followed by an unblock
(due to broadcast primitives) issued by the driver is
interspersed by the kernel changing the state of the device.
Therefore the unblock by the driver results in a no operation
within the kernel API.
To fix this one, the below patch checks the return of the unblock API
and performs a block followed by an unblock to unfreeze the block
layer's I/O queue. Sufficient checks and prints are also added in the
driver to identify this condition caused by the kernel.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Added dma_mapping_error() API after mapping an address with dma_map_single()
API. Otherwise when CONFIG_DMA_API_DEBUG is enabled in the kernel, then it
complains about mpt3sas driver not calling dma_mapping_error after mapping an
address with dma_map_single
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Created a thread using alloc_ordered_workqueue() API in order to process
the works from firmware Work-queue sequentially instead of
create_singlethread_workqueue() API.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
scsi_dma_map API will return a negative value (i.e. -ENOMEM)
if DMA mapping of sg lists fails and zero if the sg list in the
SCSI cmd is NULL. But drivers doesn't handled sg list DMA mapping
failure case properly.
So, Updated the code to return host busy error status to SCSI MID Layer(SML),
when DMA mapping of scatter gather list fails for a SCSI command.
So that SML will retry this SCSI cmd after some time.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.
The definition of this log info value is
"Virtual IO has failed and has to be retried".
Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Below are the new changes to MPI 2.5 Rev K(2.5.6) specification and 2.00.35
header files
1) Added a minimum size requirement for target mode command buffers.
2) Added MinMSIxIndex and MaxMSIxIndex fields to CommandBufferPostBase
Request.
3) For BIOS Page 1, added SSUTimeout field, and added Product Name String
Format bits to the BiosOptions field
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Following is the change set,
1. Added more defines for the BiosOptions field of MPI2_CONFIG_PAGE_BIOS_1.
2. Added MPI2_TOOLBOX_CLEAN_BIT26_PRODUCT_SPECIFIC definition.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,
- When end device is added in the topology,
- When the end device is removed from the setup,
- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
error handling,
- When any command to the device fails with Sense key Hardware error or Medium
error or Unit Attention,
- When firmware returns device error or device not ready status for the end
device,
- When a Predicted fault is detected on an end device.
This information can be used by the user to identify the location of the
desired drive in the topology.
Driver will get these information by reading the sas device page0.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Update MPI 2.5 Release: MPI 2.5 Rev I (2.5.4) specification and 2.00.33 header
files
Below is the change set from the MPI specification for I Rev
1) Added Base Enclosure Level bit to the Flags field of Manufacturing Page 7.
2) Updated description of the MaxTargetPortConnectTime field of SAS IO Unit
Page 1.
3) Added EnclosureLevel and ConnectorName fields to SAS Device Page 0. Also,
added EnclosureLevel and ConnectorName Valid bit to the Flags field.
4) Added EnclosureLevel field to SAS Enclosure Page 0. Also, added
EnclosureLevel Valid bit to the Flags field.
5) Added value for BIOS image to HashImageType.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.
This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.
Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver initialization fails if driver tries to send IOC facts request message
when the IOC is in reset or in a fault state.
This patch will make sure that
1.Driver to send IOC facts request message only if HBA is in operational or
ready state.
2.If IOC is in fault state, a diagnostic reset would be issued.
3.If IOC is in reset state then driver will wait for 10 seconds to exit out
of reset state. If the HBA continues to be in reset state, then the HBA
wouldn't be claimed by the driver.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.
Following are changes that are done in this patch
1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.
2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].
3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.
4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver crashes if the BIOS do not set up at least one
memory I/O resource. This failure can happen if the device is too
slow to respond during POST and is missed by the BIOS, but Linux
then detects the device later in the boot process.
Based on a patch from Timothy Pearson <tpearson@raptorengineeringinc.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Added a support to set cpu affinity mask for each MSIX vector enabled
by the HBA. So that, running the irqbalancer will balance interrupts among
the cpus.
Change_set:
1. Added affinity_hint varable of type cpumask_var_t in adapter_reply_queue
structure. And allocated a memory for this varable by calling
alloc_cpumask_var.
2. Call the API irq_set_affinity_hint for each MSIx vector to affiniate it
with calculated cpus at driver inilization time.
3. While freeing the MSIX vector, call this same API to release the cpu
affinity mask for each MSIx vector by providing the NULL value in
cpumask argument.
4. then call the free_cpumask_var API to free the memory allocated in step 2.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change Set:
1. Extended the upper boundary restriction for the module parameter
max_sgl_entries. Earlier, the max_sgl_entries was capped at the
SCSI_MAX_SG_SEGMENTS kernel definition. With this change, the user
would be able to set the max_sgl_entries to any value which is
greater than SCSI_MAX_SG_SEGMENTS and less than the minimum of
SCSI_MAX_SG_CHAIN_SEGMENTS & hardware limit (Calculated using
IOCFacts's MaxChainDepth).
2. Added a print for the message log whenever the user sets the
max_sgl_entries to a value greater than SCSI_MAX_SG_SEGMENTS to
warn about the kernel definition overriding.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a flaky disk is there in a topology then during driver load,
discovery related I/O times out; which results in SCSI error recovery
initiating host reset and then the controller won't see any disk.
In this patch, The driver would return FAILED status to the host reset
initiated due to discovery related I/O timeout if ioc->is_driver_loading
is set. This flag would be set until we exit out of scsih_scan_finished().
i.e.
During device discovery if one of the disk is flaky
(which responds to some discovery commands and doesn't respond to some)
the driver wouldn't perform host reset for discovery related I/O timeout.
Instead it would return Failure for the host reset resulting in the
flaky disk getting removed by the SCSI Mid layer,
so other disks would be added correctly.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.
The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y
where a b c d are threshold flags 0 1 2 3
Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
firmware, then print the sensor number, the maximum threshold number it
has exceed and the current temperature of this sensor.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The "issue_reset" can be used uninitialized. It should be set to false
at the start.
Also I cleaned up the types a little by using bool.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This reverts commit 963ba22b90
("mpt3sas: Remove phys on topology change")
Reverting the previous mpt3sas drives patch changes,
since we will observe below issue
Issue:
Drives connected Enclosure/Expander will unregister with
SCSI Transport Layer, if any one remove and add expander
cable with in DMD (Device Missing Delay) time period or
even any one power-off and power-on the Enclosure with in
the DMD period.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
In _scsih_probe, propagate the return value from scsi_add_host.
In mpt3sas, avoid calling list_del twice if that returns an
error, which causes list_del corruption warnings if an error
is returned.
Tested with blk-mq and scsi-mq patches to properly cleanup
from and propagate blk_mq_init_rq_map errors.
Signed-off-by: Robert Elliott <elliott@hp.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt3sas driver version to 04.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.
When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.
The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.
But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.
So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.
When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.
Change set in v1:
1. Declared the _base_get_ioc_facts() functions at the beginning of the mpt3sas_base.c file
instead of moving all these functions before mpt3sas_base_map_resources() function
a. _base_wait_for_doorbell_int()
b. _base_wait_for_doorbell_ack()
c. _base_wait_for_doorbell_not_used()
d. _base_handshake_req_reply_wait()
e. _base_get_ioc_facts()
2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.
3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
a. _base_release_memory_pools()
b. _base_allocate_memory_pools()
c. _base_send_ioc_init()
d. _base_make_ioc_operational()
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Copyright in driver sources is updated for year the 2014.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the change set in MPI2.5 Rev H specification and 2.00.32 header files
1) Added reserved fields to IO Unit Page 7 for future use.
2) Added optional functionality to IOCInit Request so that
the host may specify a separate base address for each
Reply Descriptor Post Queue. IOC support for this is
indicated using a new IOCCapabilities bit in the IOCFacts Reply.
3) Added Toolbox Console Text Display Tool
The host uses the Console Text Display Tool to send a string to
IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal).
4) Firmware images can now be signed using an encrypted hash.
5) Added MPI2_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL
6) Added more details about configuration page restrictions when Host Based Discovery is enabled
Enabling host based discovery affects the availability of some configuration pages and events.
The SAS Expander, SAS Device, and SAS Enclosure configuration pages are not available from the IOC.
The IOC returns an error status to any Configuration Request message attempting to access these pages.
The IOC does not send the SAS Discovery Event, the SAS Topology Change List Event, or
the SAS Enclosure Device Status Change Event when host based discovery is enabled.
7) Bit 13 of the SAS IO Unit Page 1 ControlFlags field is now obsolete.
It was used to enable limiting direct attached SATA maximum link rate to 1.5 Gbps.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump mpt3sas driver version to 03.100.00.00.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added code to send an SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).
Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends an SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Below is the change set in MPI2.5 Rev G specification and 2.00.31 header files
1) Added SCSIStatusQualifier to SCSI IO Error Reply message.
2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field.
3) Added Allow Protection Information bit for IR Volume Create.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In _scsih_probe, delay the call to scsi_add_host until the host has been
fully set up.
Otherwise, the default .can_queue value of 1 causes scsi-mq to set the block
layer request queue size to its minimum size, resulting in awful performance.
In _scsih_probe error handling, call mpt3sas_base_detach rather than
scsi_remove_host to properly clean up in reverse order.
In _scsih_remove, call scsi_remove_host earlier to clean up in reverse order.
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@avagotech.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On systems with a non power-of-two CPU count the existing MSI-X grouping
code failed to distribute interrupts correctly. Rework the code to
handle arbitrary processor counts.
Also remove the hardcoded upper limit on the number of processors so we
can boot on large systems.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tack the firmware reply event_data payload to the end of its
corresponding struct fw_event_work allocation. This matches the
convention in the mptfusion driver and simplifies the code.
This avoids the following smatch warning:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:2519
mpt3sas_send_trigger_data_event() warn: possible memory leak of
'fw_event'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_{slave,target}_alloc, an incorrect structure type is passed
to sizeof() when allocating storage for hostdata. Luckily larger
structure types were used, so at least the wrong sizes were safe:
struct scsi_device (1784 bytes) > struct MPT3SAS_DEVICE (24 bytes)
struct scsi_target (760 bytes) > struct MPT3SAS_TARGET (32 bytes)
This fixes the following smatch warnings:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1166 _scsih_target_alloc()
warn: struct type mismatch 'MPT3SAS_TARGET vs scsi_target'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1280 _scsih_slave_alloc()
warn: struct type mismatch 'MPT3SAS_DEVICE vs scsi_device'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Removing the host_lock from the I/O submission path gives a huge
scalability improvement.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Praveen Krishnamoorthy <Praveen.krishnamoorthy@lsi.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
