Change change_page_attr_set_clr() array parameter to a flag. This helps
following patches which adds an interface to change attr to uc/wb over a
set of pages referred by struct page.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: arjan@infradead.org
Cc: eric@anholt.net
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: airlied@redhat.com
LKML-Reference: <20090319215358.611346000@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, remove last user of set_pte_present
set_pte_vaddr() is only used to install ptes in fixmaps, and
should never be used to overwrite a present mapping.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
LKML-Reference: <1237406613-2929-1-git-send-email-jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix rarely-used feature
The VGA Miscellaneous Output Register is read from address 0x3CC but
written to address 0x3C2. This was missed when this code was
converted from assembly to C. While we're at it, clean up the code by
making the overflow bits and the math used to set the bits explicit.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
Refactor the MP-table parsing code via the introduction of the
following helper functions:
skip_entry()
smp_reserve_bootmem()
check_irq_src()
check_slot()
To simplify the code flow and to reduce the size of the
following oversized functions: smp_read_mpc(), smp_scan_config().
There should be no impact to functionality.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/cpu/mtrr/cleanup.c:197: warning: format ‘%d’ expects type ‘int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1237378015.13488.1.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot crash on UV systems
Commit 76ba0ecda0 "cpumask: use
cpumask_var_t in uv_flush_tlb_others" used cur_cpu as an iterator;
it was supposed to be zero for the code below it.
Reported-by: Cliff Wickman <cpw@sgi.com>
Original-From: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Mike Travis <travis@sgi.com>
Cc: steiner@sgi.com
Cc: <stable@kernel.org>
LKML-Reference: <200903180822.31196.rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: optimize APIC IPI related barriers
Uncached MMIO accesses for xapic are inherently serializing and hence
we don't need explicit barriers for xapic IPI paths.
x2apic MSR writes/reads don't have serializing semantics and hence need
a serializing instruction or mfence, to make all the previous memory
stores globally visisble before the x2apic msr write for IPI.
Add x2apic_wrmsr_fence() in flush tlb path to x2apic specific paths.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "steiner@sgi.com" <steiner@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
LKML-Reference: <1237313814.27006.203.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Attempting to rid us of the problematic work_on_cpu(). Just use
smp_call_function_single() here.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <20090318042217.EF3F1DDF39@ozlabs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix spurious IRQs
During irq migration, we send a low priority interrupt to the previous
irq destination. This happens in non interrupt-remapping case after interrupt
starts arriving at new destination and in interrupt-remapping case after
modifying and flushing the interrupt-remapping table entry caches.
This low priority irq cleanup handler can cleanup multiple vectors, as
multiple irq's can be migrated at almost the same time. While
there will be multiple invocations of irq cleanup handler (one cleanup
IPI for each irq migration), first invocation of the cleanup handler
can potentially cleanup more than one vector (as the first invocation can
see the requests for more than vector cleanup). When we cleanup multiple
vectors during the first invocation of the smp_irq_move_cleanup_interrupt(),
other vectors that are to be cleanedup can still be pending in the local
cpu's IRR (as smp_irq_move_cleanup_interrupt() runs with interrupts disabled).
When we are ready to unhook a vector corresponding to an irq, check if that
vector is registered in the local cpu's IRR. If so skip that cleanup and
do a self IPI with the cleanup vector, so that we give a chance to
service the pending vector interrupt and then cleanup that vector
allocation once we execute the lowest priority handler.
This fixes spurious interrupts seen when migrating multiple vectors
at the same time.
[ This is apparently possible even on conventional xapic, although to
the best of our knowledge it has never been seen. The stable
maintainers may wish to consider this one for -stable. ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: stable@kernel.org
Impact: fix possible race
save_mask_IO_APIC_setup() was using non atomic memory allocation while getting
called with interrupts disabled. Fix this by splitting this into two different
function. Allocation part save_IO_APIC_setup() now happens before
disabling interrupts.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
Clean up #ifdefs and replace them with helper functions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: simplification
In the current code, for level triggered migration, we need to modify the
io-apic RTE with the update vector information, along with modifying interrupt
remapping table entry(IRTE) with vector and destination. This is to ensure that
remote IRR bit inthe IOAPIC RTE gets cleared when the cpu does EOI.
With this patch, for level triggered, we eliminate the io-apic RTE modification
(with the updated vector information), by using a virtual vector (io-apic pin
number). Real vector that is used for interrupting cpu will be coming from
the interrupt-remapping table entry. Trigger mode in the IRTE will always be
edge, and the actual level or edge trigger will be setup in the IO-APIC RTE.
So a level triggered interrupt will appear as an edge to the local apic
cpu but still as level to the IO-APIC.
With this change, level irq migration can be done by simply modifying
the interrupt-remapping table entry with out changing the io-apic RTE.
And as the interrupt appears as edge at the cpu, in addition to do the
local apic EOI, we need to do IO-APIC directed EOI to clear the remote
IRR bit in the IO-APIC RTE.
This simplies the irq migration in the presence of interrupt-remapping.
Idea-by: Rajesh Sankaran <rajesh.sankaran@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup, paranoia
We were not clearing the local APIC in clear_local_APIC() in the
presence of x2apic. Fix it.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: make kexec work with x2apic
disable_IO_APIC() gets called during crashdump aswell, which configures the
IO-APIC/LAPIC so that legacy interrupts can be delivered for the kexec'd kernel.
In the presence of interrupt-remapping, we need to change the
interrupt-remapping configuration aswell as modifying IO-APIC for virtual wire
B mode.
To keep things simple during the crash, use virtual wire A mode
(for which we don't need to touch io-apic and interrupt-remapping tables).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: interface augmentation (not yet used)
Enable fault handling flow for intr-remapping aswell. Fault handling
code now shared by both dma-remapping and intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
The setup code is mostly 16-bit code, but there is a small stub of
32-bit code at the end. Move the 32-bit code to a separate segment,
.text32, to avoid scrambling the disassembly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: build fix with CONFIG_RELOCATABLE
Move _end into a dummy section, so that relocs.c will know it is a
relocatable symbol.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Impact: disambiguate real .bss variables from .brk storage
Add a .brk section after the .bss section. This has no effect
on the final vmlinux, but it more clearly distinguishes the space
taken by actual .bss symbols, and the variable space reserved
by .brk users.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: bulletproofing, clarification
The brk reservation symbols are just there to document the amount
of space reserved by brk users in the final vmlinux file. Their
addresses are irrelevent, and using their addresses will cause
certain havok. Name them ".brk.NAME", which is a valid asm symbol
but C can't reference it; it also highlights their special
role in the symbol table.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: Tighten bound to avoid masking errors
The definition of MAPPING_BEYOND_END was excessive; this has a nasty
tendency to mask bugs. We have learned over time that this kind of
bug hiding can cause some very strange errors. Therefore, tighten the
bound to only need to map the actual kernel area.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Impact: cleanup
ALLOCATOR_SLOP is a vestigial remain from when we used the
bootmem allocator to allocate the kernel's linear memory mapping.
Now we directly reserve pages from the e820 mapping, and no
longer require secondary structures to keep track of allocated
pages.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: crash fix
head_32.S needs to map the kernel itself, and enough space so
that mm/init.c can allocate space from the e820 allocator
for the linear map of low memory.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Don't boost at the addresses which are listed on exception tables,
because major page fault will occur on those addresses. In that case,
kprobes can not ensure that when instruction buffer can be freed since
some processes will sleep on the buffer.
kprobes-ia64 already has same check.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order for ntpd to correctly synchronize the clocks, the frequency of
the system clock must not be off by more than 500 ppm (or, put another
way, 1:2000), or ntpd will end up giving up on trying to synchronize
properly, and ends up reseting the clock in jumps instead.
The fast TSC PIT calibration sometimes failed this test - it was
assuming that the PIT reads always took about one microsecond each (2us
for the two reads to get a 16-bit timer), and that calibrating TSC to
the PIT over 15ms should thus be sufficient to get much closer than
500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm
error value).
However, that assumption does not always hold: apparently some hardware
is either very much slower at reading the PIT registers, or there was
other noise causing at least one machine to get 700+ ppm errors.
So instead of using a fixed 15ms timing loop, this changes the fast PIT
calibration to read the TSC delta over the individual PIT timer reads,
and use the result to calculate the error bars on the PIT read timing
properly. We then successfully calibrate the TSC only if the maximum
error bars fall below 500ppm.
In the process, we also relax the timing to allow up to 25ms for the
calibration, although it can happen much faster depending on hardware.
Reported-and-tested-by: Jesper Krogh <jesper@krogh.cc>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: don't trim e820 according to wrong mtrr
Ozan reports that his server emits strange warning.
it turns out the BIOS sets the MTRRs incorrectly.
Ignore those strange ranges, and don't trim e820,
just emit one warning about BIOS
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BEE1E7.7020706@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix crash on VMI (VMware)
When we generate a call sequence for calling a paravirtualized
function, we presume that the generated code is "call *0xXXXXX",
which is a 6 byte opcode; this is larger than a normal
direct call, and so we can patch a direct call over it.
At the moment, however we give gcc enough rope to hang us by
putting the address in a register and generating a two byte
indirect-via-register call. Prevent this by explicitly
dereferencing the function pointer and passing it into the
asm as a constant.
This prevents crashes in VMI, as it cannot handle unpatchable
callsites.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Alok Kataria <akataria@vmware.com>
LKML-Reference: <49BEEDC2.2070809@goop.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Bug fix on UP
Referring commit cc3ca22063,
Peter removed __cpuinit annotations for mce_cpu_features()
and its successor functions, which caused troubles on UP
configurations.
However the intel_init_cmci() was introduced after that and
it also has __cpuinit annotation even though it is called from
mce_cpu_features(). Remove the annotation from that function
too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
asm/highmem.h inclusion is added to use kmap_atomic_prot_pfn()
by commit bb6d59ca92
Now kmap_atomic_prot_pfn is moved to iomap_32.c
by commit dd63fdcc63
So the asm/highmem.h inclusion in iomap_32.c is unnecessary now.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
LKML-Reference: <20090315151517.GA29074@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: help debug e820 bugs
Try to print out more info, to catch wrong call parameters.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BCB557.3030000@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot crash
Need to exit early if the addr is far above 64k.
The crash got exposed by:
78a8b35: x86: make e820_update_range() handle small range update
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
LKML-Reference: <49BC2279.2030101@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: makes vmlinux section information more useful
Don't use ram after _end blindly for pagetables. aka init pages is before _end
put those pg table into .bss
[Adapted to use brk segment - Jeremy]
v2: keep initial page table up to 512M only.
v4: put initial page tables just before _end
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: new interface; remove hard-coded limit
Add RESERVE_BRK(name, size) macro to reserve space in the brk
area. This should be a conservative (ie, larger) estimate of
how much space might possibly be required from the brk area.
Any unused space will be freed, so there's no real downside
on making the reservation too large (within limits).
The name should be unique within a given file, and somewhat
descriptive.
The C definition of RESERVE_BRK() ends up being more complex than
one would expect to work around a cluster of gcc infelicities:
The first attempt was to simply try putting __section(.brk_reservation)
on a variable. This doesn't work because it ends up making it a
@progbits section, which gets actual space allocated in the vmlinux
executable.
The second attempt was to emit the space into a section using asm,
but gcc doesn't allow arguments to be passed to file-level asm()
statements, making it hard to pass in the size.
The final attempt is to wrap the asm() in a function to allow
it to have arguments, and put the function itself into the
.discard section, which vmlinux*.lds drops entirely from the
emitted vmlinux.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: simplification
We only need to map the kernel in head_32.S, not the whole of
lowmem. We use 512MB as a reasonable (but arbitrary) limit on
the maximum size of the kernel image.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Use extend_brk() to allocate memory for DMI rather than having an
ad-hoc allocator.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: use new interface instead of previous ad hoc implementation
Rather than having special purpose init_pg_table_start/end variables
to delimit the kernel pagetable built by head_32.S, just use the brk
mechanism to extend the bss for the new pagetable.
This patch removes init_pg_table_start/end and pg0, defines __brk_base
(which is page-aligned and immediately follows _end), initializes
the brk region to start there, and uses it for the 32-bit pagetable.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: build fix
The brk initialization functions were incorrectly located inside
an #ifdef CONFIG_VLK_DEV_INITRD block, causing the obvious build failure in
minimal configurations.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: new interface
Add a brk()-like allocator which effectively extends the bss in order
to allow very early code to do dynamic allocations. This is better than
using statically allocated arrays for data in subsystems which may never
get used.
The space for brk allocations is in the bss ELF segment, so that the
space is mapped properly by the code which maps the kernel, and so
that bootloaders keep the space free rather than putting a ramdisk or
something into it.
The bss itself, delimited by __bss_stop, ends before the brk area
(__brk_base to __brk_limit). The kernel text, data and bss is reserved
up to __bss_stop.
Any brk-allocated data is reserved separately just before the kernel
pagetable is built, as that code allocates from unreserved spaces
in the e820 map, potentially allocating from any unused brk memory.
Ultimately any unused memory in the brk area is used in the general
kernel memory pool.
Initially the brk space is set to 1MB, which is probably much larger
than any user needs (the largest current user is i386 head_32.S's code
to build the pagetables to map the kernel, which can get fairly large
with a big kernel image and no PSE support). So long as the system
has sufficient memory for the bootloader to reserve the kernel+1MB brk,
there are no bad effects resulting from an over-large brk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
Move the symbols delimiting a section part of the section
(section relative) rather than absolute. This avoids any
unexpected gaps between the section-start symbol and the first
data in the section, which could be caused by implicit
alignment of the section data. It also makes the general
form of vmlinux_64.lds.S consistent with vmlinux_32.lds.S.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
there should be no difference, except:
* the 64bit variant now also initializes the padlock unit.
* ->c_early_init() is executed again from ->c_init()
* the 64bit fixups made into 32bit path.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: herbert@gondor.apana.org.au
LKML-Reference: <1237029843-28076-2-git-send-email-sebastian@breakpoint.cc>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: print out fewer lines
1. print continuous range with same type together
2. change _INFO to _DEBUG
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BACB61.8000302@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix debug warning
Jaswinder noticed that there is a warning about smp_processor_id()
in get_mtrr().
Fix it by wrapping the printout into a get/put_cpu() pair.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <49BAB7FF.4030107@kernel.org>
[ changed to get/put_cpu(), cleaned up surrounding code a it. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
