The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown. Check for
support before attempting to disable the feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default the driver opens 8 TX queues (defined by MLX4_EN_NUM_TX_RINGS).
If the driver is configured to support Per Priority Flow Control, we open
8 additional TX rings.
dev->real_num_tx_queues is always set to be MLX4_EN_NUM_TX_RINGS.
The mlx4_en_select_queue() function uses standard hashing (skb_tx_hash)
in case that PPFC is not supported or the skb contain a vlan tag,
otherwise the queue is selected according to vlan priority.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt moderation should not depend on number of incoming
bytes, but on number of incoming packets.
The previous scheme caused very high interrupts rate for small
messages when big MTU was configured.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the initialization of one of the ports failed,
there is no need to fail the other one as well.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
en_params.c file now only handles Ethtool functionality
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network device TX is never run in IRQ context, and skb is freed outside
of the IRQ-disabling spin lock. So checking for IRQ was a waste of time
here.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slight refactoring of duplicated wait for idle checks
Spelling fix
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: jie.yang@atheros.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Several EISA device IDs for 3c509 family network cards are missing from
the driver, making the cards unusable in their EISA mode. Here's a fix to
add them based on the EISA configuration files distributed by 3Com and our
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be stopping the subqueues in cpmac_end_xmit
but rather test the status of them. Replace the calls to
netif_subqueue_stop by __netif_subqueue_stopped. This
fixes an unrecoverable exception from happening when
running the driver.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unused variables in
cpmac_hw_error, cpmac_tx_timeout and cpmac_probe.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};
See also Documentation/powerpc/dts-bindings/can/sja1000.txt.
CC: devicetree-discuss@ozlabs.org
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed on the netdev mailing list, the member "base_addr" of
"struct net_device" should not be (mis)used to store the virtual
address to the SJA1000 register area. According to David Miller,
it's only use is to allow ISA and similar primitive bus devices to
have their I/O ports changed via ifconfig. The virtual address is
now stored in the private data structure of the SJA1000 device and
the callback functions use "struct sja1000_priv" instead of the
unneeded "struct net_device".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a few errors sneaked into the initial version of the
device driver interface.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning messages coming from rtl8150 driver can flood the console
and make a DTV/set-top-box unable to decode video/audio frames.
'Pegasus' driver handles this situation similarly, preventing this
from happening there.
It happens with a low cost BCM MIPS embedded platform, whenever
timeout errors were coming from usbnet device, making platform
unusable for viewer watching.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FEC support for MX35 processor.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds power management suspend/resume hooks for irda-usb.
Signed-off-by: Tadashi Abe <tabe@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Gary Lin reports that a new device id needs to be added to the atl1e in
order to get some new Asus hardware to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the AEL2020 phy.
Add PCI IDs of the boards using this phy.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we register the MII bus to the platfrom bus, the Distributed Switch
Architecture can hook in transparently.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove dead long delay
- Use proper defines
- Remove broken implementation of the TX DMA Data Alignment TXDWA feature
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writes to the DMA descriptors may sit in the internal Blackfin data buffers
and not actually be available when the DMA engine goes to fetch them. This
does not typically happen, but when dealing with short/fast packets such as
UDP and polling KGDB, this occurs much more frequently. Same goes for
heavy loads as seen by netperf tests or large scp transfers. So force the
buffers to drain with SSYNC otherwise we get random malformed packets.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IRQ used by the Blackfin EMAC is internal to the peripheral and cannot
be used to generate any other interrupt, so there is no point in marking it
as IRQF_SHARED.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to release skb->dst, its now done by core network.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
http://bugzilla.kernel.org/show_bug.cgi?id=13312
at76_dwork_hw_scan holds a mutex while calling ieee80211_scan_completed,
which then calls at76_config which needs the same mutex. This reworks
the ordering to not hold the lock while calling ieee80211_scan_completed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the build for CONFIG_NET_POLL_CONTROLLER that I broke with
217cbfa856 ("mac8390: fix regression
caused during net_device_ops conversion").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5e68b772e6
cxgb3: map entire Rx page, feed map+offset to Rx ring.
introduced a regression on platforms defining DECLARE_PCI_UNMAP_ADDR()
and related macros as no-ops.
Rx descriptors are fed with the a page buffer bus address + page chunk offset.
The page buffer bus address is set and retrieved through
pci_unamp_addr_set(), pci_unmap_addr().
These functions being meaningless on x86 (if CONFIG_DMA_API_DEBUG is not set).
The HW ends up with a bogus bus address.
This patch saves the page buffer bus address for all plaftorms.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the korina driver poll the media
for link change. This is actually required on
Mikrotik RB532 (not RB532A) for korina to
operate properly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:
/* Backwards compat, remove in 2.7.x */
#define dma_sync_single dma_sync_single_for_cpu
#define dma_sync_sg dma_sync_sg_for_cpu
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.
If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.
To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is requested (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
From a fix by Cindy H Kao:
Block size has to be set before sending IOE enable because the
firmware reads the block size register before it reads IOE register.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Functions i2400m_report_tlv*() are only called from
i2400m_report_hook(), called in a workqueue by
i2400m_report_hook_work(). The scheduler checks for device readiness
before scheduling.
Added an extra check for readiness in i2400m_report_hook_work(), which
makes all the checks down the line redundant.
Obviously the device state could change in the middle, but error
handling would take care of that.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user',
the driver will echo to user space all the commands being sent to the
device from user space, along with the responses.
However, this only helps with the commands being sent from user space;
with this patch, the trace hook is moved to i2400m_msg_to_dev(), which
is the single access point for running commands to the device (both by
user space and the kernel driver). This allows better debugging by
having a complete stream of commands/acks and reports.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When commands are sent from user space, trace both the command sent
and the answer received over the "echo" pipe instead of over the
"trace" pipe when command tracing is enabled. As well, when the device
sends a reports/indications, send it over the "echo" pipe.
The "trace" pipe is used by the device to send firmware traces;
gets confusing. Another named pipe makes it easier to split debug
information.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The WiMAX i2400m driver needs to generate a fake source MAC address to
fake an ethernet header (for destination, the card's MAC is
used). This is the source of the packet, which is the basestation it
came from. The basestation's mac address is not usable for this, as it
uses its own namespace and it is not always available.
Currently the fake source MAC address was being set to all zeros,
which was causing trouble with bridging.
Use random_ether_addr() to generate a proper one that creates no
trouble.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
First of all, it exposes the SKB list implementation.
Second of all it's not needed. If we get called here, we
successfully enqueued the URB with the linked SKB and
such a completion only gets called one time on such an
SKB.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct net_device_stats provided in struct net_device instead of
private ones.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the not-that-useful message in the
r6040_timer which prints the PHY status. Instead
replace it with a call to mii_check_media which will
update the link status and print it on startup.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build warning due to an unused label.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit "convert to net_device_ops" broke the Blackfin MAC
driver as it declared the new structure before the function it used:
CC drivers/net/bfin_mac.o
drivers/net/bfin_mac.c:984: error: ‘bfin_mac_close’ undeclared here (not in a function)
make[1]: *** [drivers/net/bfin_mac.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8169 driver supports 3 different families of network chips
(RTL8169, RTL8168 and RTL8101). When an unknown version is found, the
driver currently always defaults to the RTL8169 variant. This has very
little chance to ever work for chips of the other families. So better
define a per-family default.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both atl1.c and atl2.c include atlx.h, which defines some modinfo
stuff. But atl2.c seems like it doesn't want the modinfo data
from atlx.h, as it defines its own.
Running modinfo on atl2.ko, we get conflicting information:
$ /sbin/modinfo drivers/net/atlx/atl2.ko | egrep "version|description|author"
version: 2.2.3
description: Atheros Fast Ethernet Network Driver
author: Atheros Corporation <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>
version: 2.1.3
author: Xiong Huang <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>, Jay Cliburn <jcliburn@gmail.com>
Move the modinfo data out of atlx.h and into atl1.c to eliminate
the confusion:
$ /sbin/modinfo drivers/net/atlx/atl1.ko | egrep "version|description|author"
version: 2.1.3
author: Xiong Huang <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>, Jay Cliburn <jcliburn@gmail.com>
description: Atheros L1 Gigabit Ethernet Driver
$ /sbin/modinfo drivers/net/atlx/atl2.ko | egrep "version|description|author"
version: 2.2.3
description: Atheros Fast Ethernet Network Driver
author: Atheros Corporation <xiong.huang@atheros.com>, Chris Snook <csnook@redhat.com>
Reported-by: Scott Scriven <scott.scriven@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by the patch for 8139too (bda6a15a).
Currently we can't set mac address on a running ucc_geth device.
But this is needed when you use this device as a bonding slave in
bonding device in balance-alb mode. So add this feature for ucc_geth
device.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gianfar interrupt handler uses IEVENT_ERR_MASK to check and handle errors.
Babbling RX error (IEVENT_BABR) should be included in IEVENT_ERROR_MASK.
Otherwise if BABR is raised, it never gets handled nor cleared, and an
interrupt storm results. This has been observed to happen on sending a
burst of ethernet frames to a gianfar based board.
Signed-off-by: Xiaotian Feng <xiaotian.feng@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is for supporting C10NEM. C10NEM is a switch module, which
has back-to-back XAUI link connected to blades.
Signed-off-by: Tanli Chang <tanli.chang@sun.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in. This patch corrects that by:
ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.
ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.
ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected. Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.
Other functions were updated to allow correct logging.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device ID 0x10d8 is the default silicon device ID for 82599. However, the
device will not be functional without an EEPROM, so we want to prevent the
driver from loading on the device. Otherwise, the driver will load, but no
PHY setup or PCIe setup will occur, causing the device to be unusable. To
prevent users from encountering this, just remove the device ID.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy port status register has the MDI-X status bit on bit 11, not bit 3
as is currently setup in the define. This patch corrects that so the
correct bit is checked on igp PHY types.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on previous patch from Jesper Dangaard Brouer.
The RNBC (Receive No Buffers Count) register for the 82576, indicate
that frames were received when there were no available buffers in host
memory to store those frames (receive descriptor head and tail
pointers were equal). The packet is still received by the NIC if
there is space in the FIFO on the NIC.
As the RNBC value is not a packet drop, the driver stores this value
in net_stats.rx_fifo_errors to indicate that there were no system
buffers available for the incoming packet. Actual dropped packets
are counted in the MPC value.
Saving the stats in dev->net_stats makes it visible via
/proc/net/dev as "fifo", and thus viewable to ifconfig
as "overruns" and 'netstat -i' as "RX-OVR".
The Receive No Buffers Count (RNBC) can already be queried by
ethtool -S as "rx_no_buffer_count".
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the previous patches from Jesper Dangaard Brouer <hawk@comx.dk>
Implement reading the per queue drop stats register
RQDPC (Receive Queue Drop Packet Count). It counts the number of
packets dropped by a queue due to lack of descriptors available.
Notice RQDPC (Receive Queue Drop Packet Count) stats only gets
incremented, if the DROP_EN bit it set (in the SRRCTL register
for that queue). If DROP_EN bit is NOT set, then the some what
equivalent count is stored in RNBC (not per queue basis).
The RQDPC register is only 12 bit, thus the precision might
suffer due to overrun in-netween the watchdog polling interval.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also convert DPRINTK to pr_debug and dev_printk to dev_<foo>.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of private struct net_device_stats in "struct atl1e_adapter",
and use one provided in struct net_device instead.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.
The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: David Dillow <dave@thedillows.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves readability by collecting CPU dependency code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the problem that this driver not update rxdesc in sh_eth_rx.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the probrem that TX/RX descirptor not set physical memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the problem that may not work receive process by cache coherency issue.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changeset ca17584bf2 ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.
Tested with a Kinetics EtherPort card.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch makes iwmc3200wifi select CFG80211 instead of LIB80211.
This fixed module link error reported by Randy Dunlap
<randy.dunlap@oracle.com> when compiling iwmc3200wifi without
cfg80211 selected. WIRELESS_EXT is also selected by iwmc3200wifi.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are already converted to new net_device_ops API
and nobody uses old API anymore.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new ID is validated by Cologne Chip.
LEDs control is also supported.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
DTMF detection was enabled when it was not supposed to.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
