pm_runtime_get_if_in_use() returns -EINVAL if runtime PM is disabled. This
should not be considered an error. Generally the driver has enabled
runtime PM already so getting this error due to runtime PM being disabled
will not happen.
Instead of checking for lesser or equal to zero, check for zero only.
Address this for drivers where this pattern exists.
This patch has been produced using the following command:
$ git grep -l pm_runtime_get_if_in_use -- drivers/media/i2c/ | \
xargs perl -i -pe 's/(pm_runtime_get_if_in_use\(.*\)) \<\= 0/!$1/'
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the calls to pm_runtime_get_noresume() and pm_runtime_put() with
pm_runtime_idle() in the driver's probe function. This will have the same
effect with fewer calls. pm_runtime_disable() in remove is sufficient as
the device is already in RPM_SUSPENDED state.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Structure i2c_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An older version of the driver patches were merged accidentally which
resulted in missing the array_size parameter that tells the length of the
array that contains the different supported sizes.
Bring it back to v4l2_find_nearest size and make the corresponding change
for the drivers using it as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, the sensor, with default settings, was outputting SOF without
data. This results in frame sync error on the receiver side.
Now, configure the sensor to output SOF with MIPI data for all frames. This
avoids possible null first frame on the bus.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ov13858 contained a 64-bit division. Use do_div() for calculating it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, with crop (0, 0), (4255, 3167), VTS < 0xC9E was resulting in
blank frames sometimes. This appeared as video flickering. But we need VTS
< 0xC9E to get ~30fps.
Omni Vision recommends to use crop (0,8), (4255, 3159) for 4224x3136. With
this crop, VTS 0xC8E is supported and yields ~30fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate pixel-rate at run time instead of compile time.
Instead of using hardcoded pixels-per-line, extract it from current sensor
mode.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, vblank range given to user was too big, falling outside
of permissible range for a given resolution. Sometimes, too low vblank
resulted in errors.
Now, limit vblank to only permissible range for a given resolution.
This change limits lower-bounds of vblank, doesn't affect upper bounds.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, possible digital gains were just 1x, 2x and 4x. These
coarse gains were not sufficient in fine-tuning the image capture.
Now, digital gain range is [0, 16x] with each step 1/1024, default 1x.
This is achieved through OV13858 MWB R/G/B gain controls.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously both link-frequency and pixel-rate reported by
the sensor was incorrect, resulting in incorrect FPS.
Report link-frequency in Hz rather than link data rate in bps.
Calculate pixel-rate from link-frequency.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, initial exposure max was set incorrectly to (0x7fff - 8).
Now, limit exposure max to current resolution (VTS - 8).
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On format change, sometimes, sensor was streaming at a much higher
FPS than the default. This was resulting in various problems like
frame drops/corruption.
Upon format change, set default vblank as current vblank. This will
ensure that sensor will start streaming at default fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for Omnivision's ov13858
sensor, the driver supports following features:
- manual exposure/gain(analog and digital) control support
- two link frequencies
- VBLANK/HBLANK support
- test pattern support
- media controller support
- runtime pm support
- supported resolutions
+ 4224x3136 at 30FPS
+ 2112x1568 at 30FPS(default) and 60FPS
+ 2112x1188 at 30FPS(default) and 60FPS
+ 1056x784 at 30FPS(default) and 60FPS
[Sakari Ailus: use V4L2_CID_DIGITAL_GAIN instead, add MAINTAINERS entry.]
Signed-off-by: Hyungwoo Yang <hyungwoo.yang@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
