dp_init_connector adjusts the encoder type if it is a eDP panel. Use
that to decide whether we should set up a hdmi connector or not.
To do so reorder the hdmi connector setup sequence in ddi_init a bit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we ever leak a non-DP compliant port width through here, we have a
pretty serious issue. So just rip out all these WARNs - if we need
them it's probably better to have them at a central place where we
compute the dp lane count.
Also use the new DDI width macro for FDI mode.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixup the embarrassing s/intel_dp->DP/temp/ mistake Paulo
spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Introduce some nice #defines for the FDI lane width fields and put
them to good use. Suggested by Ville.
v3: Fixup the mask vs. shift copy&pasta fail Imre Deak spotted, and
use the shift #define also in the mask.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for two reasons:
- Correct handling of shared fdi lanes on ivb with fastboot.
- Handling fdi link bw limits when we only have two fdi lanes by
dithering down a bit.
Just search&replace in this patch, no functional change at all.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And put the pfit stuff into substructs while we're at it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are trying to have more platform-orthogonal pieces of code. The DDI
code shouldn't mention Haswell.
v2: Fix the email address
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alway use the alphabetical names in debug/error messages for planes,
pipes and ports, instead of using decimal numbers occasionally.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we couldn't find a pipe we shouldn't return true. This might be even
better as a WARN though, since it should be impossible to have the port
enabled without a pipe selected.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The procedure has now 3 steps:
1. Compute the bpp that the plane will output, this is done in
pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also,
this function clamps the pipe_bpp to whatever limit the EDID of any
connected output specifies.
2. Adjust the pipe_bpp in the encoder and crtc functions, according to
whatever constraints there are.
3. Decide whether to use dither by comparing the stored plane bpp with
computed pipe_bpp.
There are a few slight functional changes in this patch:
- LVDS connector are now also going through the EDID clamping. But in
a 2nd change we now unconditionally force the lvds bpc value - this
shouldn't matter in reality when the panel setup is consistent, but
better safe than sorry.
- HDMI now forces the pipe_bpp to the selected value - I think that's
what we actually want, since otherwise at least the pixelclock
computations are wrong (I'm not sure whether the port would accept
e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick
the next higher bpc value, since otherwise there's no way to make
use of the 12 bpc mode (since the next patch will remove the 12bpc
plane format, it doesn't exist).
Both of these changes are due to the removal of the
pipe_bpp = min(display_bpp, plane_bpp);
statement.
Another slight change is the reworking of the dp bpc code:
- For the mode_valid callback it's sufficient to only check whether
the mode would fit at the lowest bpc.
- The bandwidth computation code is a bit restructured: It now walks
all available bpp values in an outer loop and the codeblock that
computes derived values (once a good configuration is found) has been
moved out of the for loop maze. This is prep work to allow us to
successively fall back on bpc values, and also correctly support bpc
values != 8 or 6.
v2: Rebased on top of Paulo Zanoni's little refactoring to use more
drm dp helper functions.
v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color
range work.
v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed.
v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the
hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked
in a later patch though again.
v6: Fix spelling in a comment.
v7: Debug output improvements for the bpp computation.
v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different
things!
v9: Reinstate the fix to properly ignore the firmware edp bpp ... this
was lost in a rebase.
v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have
that. Still unsure whether this is the way to go, but at least 6bpc
for a 8bpc hdmi output seems to work.
v11: And g4x/vlv also lack 12bpc hdmi support, so only support high
depth on DP. Adjust the code.
v12: Rebased.
v13: Split out the introduction of pipe_config->dither|pipe_bpp, as
requested from Jesse Barnes.
v14: Split out the special 6BPC handling for DP, as requested by Jesse
Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to compute this earlier. To avoid a big complicated patch,
this patch here just does the big search&replace and still calls the
old functions at the same places.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is used way too often in the enable/disable paths. And will
be even more useful in the future.
Note that correct semantics of this change highly depend upon
correct updating of intel_crtc->config: Like with all other
modeset state, we need to call ->disable with the old config,
but ->mode_set and ->enable with the new config.
v2: Do not yet use the flag in the ->disable callbacks - atm we don't
yet have support for the information stored in the pipe_config in the
hw state readout code, so this will be wrong at boot-up/resume.
v3: Rebased on top of the hdmi/dp ddi encoder merging.
v4: Fixup stupid rebase error which lead to a NULL vfunc deref.
v5: On haswell the VGA port is on the PCH!
v6: s/IS_HASWELL/HAS_DDI/, spotted by Paulo Zanoni. Also add a missing
parameter name in a function declaration.
v7: Don't forget to git add ...
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If TRANS_DDI_FUNC_CTL has been wrongly programmed with an incorrect
port, we are currently trying to read PORT_CLK_SEL(port) with an
uninitialized value.
Handle that case by returning PORT_CLK_SEL_NONE and warning about it.
v2: Move the warning inside intel_ddi_get_crtc_pll (Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are really talking about the transcoder function here and the disable
version uses trancoder in its name already, so let's try to be
consistent.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our static analysis tool noticed that 'reg' could be used uninitialized if
we are trying to get a PLL to drive VGA and SPLL is already in use
(plls->spll_refcoung != 0).
In the (error) case above, let's return false to the caller and emit an
error.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into drm-intel-next-queued
Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in
commit a321e91b6d
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Feb 27 17:02:56 2013 -0800
lib/scatterlist: add simple page iterator
The merge itself is just two trivial conflicts:
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our mode set sequence documentation says audio must be disabled first.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict since the first patch in this series isn't
applied yet. Also bikeshed commit message as suggested by Ben.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bunch of fixes, nothing truely horrible:
- Fix PCH irq handling race which resulted in missed gmbus/dp aux irqs
and subsequent fallout (Paulo)
- Fixup off-by-one in our hsw id table (Kenneth)
- Fixup ilk rc6 support (disabled by default), regression introduced in
3.8
- g4x plane w/a from Egbert Eich
- gen2/3/4 dpms suspend/standy fixes for VGA outputs from Patrik Jakobsson
- Workaround dying ivb machines with less aggressive rc6 values (Stéphane
Marchesin)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/i915: Fix Haswell/CRW PCI IDs.
drm/i915: Don't clobber crtc->fb when queue_flip fails
drm/i915: wait_event_timeout's timeout is in jiffies
drm/i915: Fix missing variable initilization
Need to initialize the variable wait to false.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's my promised pile of fixes for 3.9. I've dropped the core prep
patches for vt-switchless suspend/resume as discussed on irc. Highlights:
- Fix dmar on g4x. Not really gfx related, but I'm fed up with getting
blamed for dmar crapouts.
- Disable wc ptes updates on ilk when dmar is enabled (Chris). So again,
dmar, but this time gfx related :(
- Reduced range support for hsw, using the pipe CSC (Ville).
- Fixup pll limits for gen3/4 (Patrick Jakobsson). The sdvo patch is
already confirmed to fix 2 bug reports, so added cc: stable on that one.
- Regression fix for 8bit fb console (Ville).
- Preserve lane reversal bits on DDI/FDI ports (Damien).
- Page flip vs. gpu hang fixes (Ville). Unfortuntely not quite all of
them, need to decide what to do with the currently still in-flight ones.
- Panel fitter regression fix from Mika Kuoppala (was accidentally left on
on some pipes with the new modset code since 3.7). This also improves
the modeset sequence and might help a few other unrelated issues with
lvds.
- Write backlight regs even harder ... another installement in our eternal
fight against the BIOS and backlights.
- Fixup lid notifier vs. suspend/resume races (Zhang Rui). Prep work for
new ACPI stuff, but closing the race itself seems worthwile on its own.
- A few other small fixes and tiny cleanups all over.
Lots of the patches are cc: stable since I've stalled on a few
not-so-important fixes for 3.8 due to the grumpy noise Linus made.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (33 commits)
intel/iommu: force writebuffer-flush quirk on Gen 4 Chipsets
drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
drm/i915: Implement pipe CSC based limited range RGB output
drm/i915: inverted brightness quirk for Acer Aspire 4736Z
drm/i915: Print the hw context status is debugfs
drm/i915: Use HAS_L3_GPU_CACHE in i915_gem_l3_remap
drm/i915: Fix PIPE_CONTROL DW/QW write through global GTT on IVB+
drm/i915: Set i9xx sdvo clock limits according to specifications
drm/i915: Set i9xx lvds clock limits according to specifications
drm/i915: Preserve the DDI link reversal configuration
drm/i915: Preserve the FDI line reversal override bit on CPT
drm/i915: add missing \n to UTS_RELEASE in the error_state
drm: Use C8 instead of RGB332 when determining the format from depth/bpp
drm: Fill depth/bits_per_pixel for C8 format
drm/i915: don't clflush gem objects in stolen memory
drm/i915: Don't wait for page flips if there was GPU reset
drm/i915: Kill obj->pending_flip
drm/i915: Fix a typo in a intel_modeset_stage_output_state() comment
drm/i915: remove bogus mutex_unlock from error-path
drm/i915: Print the pipe control page GTT address
...
Some (but not all) of the HDMI registers can be used to control sDVO,
so those registers have two names. IMHO, when we're talking about
HDMI, we really should call the HDMI control register "hdmi_reg"
instead of "sdvox_reg", otherwise we'll just confuse people reading
our code (we now have platforms with HDMI but without SDVO). So now
"struct intel_hdmi" has a member called "hdmi_reg" instead of
"sdvox_reg".
Also, don't worry: "struct intel_sdvo" still has a member called
"sdvo_reg".
v2: Rebase (v1 was sent in May 2012).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly to:
commit 6a0d1df3d3a0d2370541164eb0595fe35dcd6de3
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Dec 11 15:18:28 2012 +0000
drm/i915: Preserve the FDI line reversal override bit on CPT
DDI port support lane reversal to easy the PCB layouting work. Let's
preserve the bit configured by the BIOS (until we find how to correctly
retrieve the information from the VBT, but this does sound more fragile
then just relying on the BIOS that has, hopefully, been validated
already.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The FDI link has supported link reversal to make the PCB layout
engineer's life easier for quite a while and we have always presered
this bit as we programmed FDI_RX_CTL with a read/modify/write sequence.
We're trying to take a bit more control over what the BIOS leaves in
various register and with the introduction of DDI, started to program
FDI_RX_CTL fully.
There's a fused bit to indicate DMI link reversal and FDI defaults to
mirroring that configuration. We have a bit to override that behaviour
that we need to preserve from the BIOS.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the driver is in control of whether it needs to disable
everything at take-over or not, we can rip this all out.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can disable (almost) all the display hw if we only use pipe A, with
the integrated edp transcoder on port A. Because we don't set the cpu
transcoder that early (yet), we need to help us with a trick to simply
check for any edp encoders.
v2: Paulo Zanoni pointed out that we also need to configure the eDP
cpu transcoder correctly.
v3: Made by Paulo Zanoni
- Rebase patch to be on top of "fix intel_init_power_wells" patch
- Fix typos
- Fix a small bug by adding a "connectors_active" check
- Restore the initial code that unconditionally enables the power
well when taking over from the BIOS
v4: Made by Paulo Zanoni
- One more typo spotted by Jani Nikula
v5: Made by Paulo Zanoni
- Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ELD info should be updated dynamically according to hot plug event.
For haswell chip, clear/set the eld valid bit and output enable bit
from callback intel_disable/eanble_ddi().
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
- seqno wrap fixes and debug infrastructure from Mika Kuoppala and Chris
Wilson
- some leftover kill-agp on gen6+ patches from Ben
- hotplug improvements from Damien
- clear fb when allocated from stolen, avoids dirt on the fbcon (Chris)
- Stolen mem support from Chris Wilson, one of the many steps to get to
real fastboot support.
- Some DDI code cleanups from Paulo.
- Some refactorings around lvds and dp code.
- some random little bits&pieces
* tag 'drm-intel-next-2012-12-21' of git://people.freedesktop.org/~danvet/drm-intel: (93 commits)
drm/i915: Return the real error code from intel_set_mode()
drm/i915: Make GSM void
drm/i915: Move GSM mapping into dev_priv
drm/i915: Move even more gtt code to i915_gem_gtt
drm/i915: Make next_seqno debugs entry to use i915_gem_set_seqno
drm/i915: Introduce i915_gem_set_seqno()
drm/i915: Always clear semaphore mboxes on seqno wrap
drm/i915: Initialize hardware semaphore state on ring init
drm/i915: Introduce ring set_seqno
drm/i915: Missed conversion to gtt_pte_t
drm/i915: Bug on unsupported swizzled platforms
drm/i915: BUG() if fences are used on unsupported platform
drm/i915: fixup overlay stolen memory leak
drm/i915: clean up PIPECONF bpc #defines
drm/i915: add intel_dp_set_signal_levels
drm/i915: remove leftover display.update_wm assignment
drm/i915: check for the PCH when setting pch_transcoder
drm/i915: Clear the stolen fb before enabling
drm/i915: Access to snooped system memory through the GTT is incoherent
drm/i915: Remove stale comment about intel_dp_detect()
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
If we fail to set the bit when needed we get some nice FDI link
training failures (AKA "black screen on VGA output").
While we don't really know how to properly choose whether we need to
set the bit or not (VBT?), just read the initial value set by the BIOS
and store it for later usage.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were previously doing exactly what the "mode set sequence for CRT"
document mandates, but whenever we failed to train the link in the
first tentative, all the other subsequent retries always failed. In
one of my monitors that has 47 modes, I was usually getting around 3
failures when running "testdisplay -a".
After this patch, even if we fail in the first tentative, we can
succeed in the next ones. So now when running "testdisplay -a" I see
around 3 times the message "FDI link training done on step 1" and no
failures.
Notice that now the "retry" code looks a lot like the DP retry code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- __iomem where there is none (I love how we mix these things up).
- Use gfp_t instead of an other plain type.
- Unconfuse one place about enum pipe vs enum transcoder - for the pch
transcoder we actually use the pipe enum. Fixup the other cases
where we assign the pipe to the cpu transcoder with explicit casts.
- Declare the mch_lock properly in a header.
There is still a decent mess in intel_bios.c about __iomem, but heck,
this is x86 and we're allowed to do that.
Makes-sparse-happy: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Use a space after the cast consistently and fix up the
newly-added cast in i915_irq.c to properly use __iomem.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Do an early return in case we don't have DDI instead of having the
whole function inside an "if" statement.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And use it whenever we call code that uses the DDIs. We already have
intel_ddi.c and prefix every function with intel_ddi_something instead of
haswell_something, so I think replacing the checks with HAS_DDI makes more
sense. Just a cosmetical change, yes I know, but I have this OCD...
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not even declared on header files.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, this code is just used by the eDP AUX channel frequency.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the missing code to send ELD for Haswell DisplayPort,
based on Xingchao's original patch.
A test was performed with HSW-D machine and NEC EA232Wmi DP monitor.
Cc: Xingchao Wang <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This covers the "Disable FDI" section from the CRT mode set sequence.
This disables the FDI receiver and also the FDI pll.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This commit makes hsw_fdi_link_train responsible for implementing
everything described in the "Enable and train FDI" section from the
Hawell CRT mode set sequence documentation. We completely rewrite
hsw_fdi_link_train to match the documentation and we also call it in
the right place.
This patch was initially sent as a series of tiny patches fixing every
little problem of the function, but since there were too many patches
fixing the same function it got a little difficult to get the "big
picture" of how the function would be in the end, so here we amended
all the patches into a single big patch fixing the whole function.
Problems we fixed:
1 - Train Haswell FDI at the right time.
We need to train the FDI before enabling the pipes and planes, so
we're moving the call from lpt_pch_enable to haswell_crtc_enable
directly.
We are also removing ironlake_fdi_pll_enable since the PLL
enablement on Haswell is completely different and is also done
during the link training steps.
2 - Use the right FDI_RX_CTL register on Haswell
There is only one PCH transcoder, so it's always _FDI_RXA_CTL.
Using "pipe" here is wrong.
3 - Don't rely on DDI_BUF_CTL previous values
Just set the bits we want, everything else is zero. Also
POSTING_READ the register before sleeping.
4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train
According to the mode set sequence documentation, this is the
right place. According to the FDI_RX_TUSIZE register description,
this is the value we should set.
Also remove the code that sets this register from the old
location: lpt_pch_enable.
5 - Properly program FDI_RX_MISC pwrdn lane values on HSW
6 - Wait only 35us for the FDI link training
First we wait 30us for the FDI receiver lane calibration, then we
wait 5us for the FDI auto training time.
7 - Remove an useless indentation level on hsw_fdi_link_train
We already "break" when the link training succeeds.
8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE
When we fail the training.
9 - Change Haswell FDI link training error messages
We shouldn't call DRM_ERROR when still looping through voltage
levels since this is expected and not really a failure. So in this
commit we adjust the error path to only DRM_ERROR when we really
fail after trying everything.
While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since
it's what we use everywhere.
10 - Try each voltage twice at hsw_fdi_link_train
Now with Daniel Vetter's suggestion to use "/2" instead of ">>1".
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Applied tiny bikesheds:
- mention in comment that we test each voltage/emphasis level twice
- realing arguments of the only untouched reg write, it spilled over
the 80 char limit ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had 2 places using X2 and one place using X1.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now intel_ddi_init is just like intel_hdmi_init and intel_dp_init: it
inits the encoder and then calls the proper init_connector functions.
Notice that for non-eDP ports we call both HDMI and DP connector init,
so we have 2 connectors attached to each DDI encoder.
After this change, intel_hdmi_init and intel_dp_init are only called
by Ivy Bridge and earlier, while hardware containing DDI outputs
should call intel_ddi_init.
Also added/removed quite a few "static" keywords due to the fact that
some function pointers were moved from intel_dp.c and intel_hdmi.c to
intel_ddi.c.
DP finally works on Haswell now! \o/
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this since now on DDI we will have 2 connectors on each
encoder.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both "intel_dp" and "intel_hdmi" structs had a "port" field, which
always had the same value. It makes more sense to move this to
intel_digital_port, so we can know the port independently of the
connector type.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all the eDP enablement bits are there, we can actually try to
use the eDP.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's an important step :)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cdclk frequency is not always the same, so the value here should
be adjusted to match it.
Version 2: call intel_ddi_get_cdclk_freq instead of reading
CDCLK_FREQ, because the register is just for earlier HW steppings.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as the other registers. This one also appeared on Haswell for the
first time, so that's why we are renaming it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.
Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.
V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register appeared in Haswell. It does not have an EDP version
because the EDP transcoder is always tied to the DDIA clock. Notice
that if we call PIPE_CLK_SEL(pipe) when pipe is PIPE_A and transcoder
is TRANSCODER_EDP we might introduce a bug, that's why this is a
transcoder register even though it does not have an EDP version.
Even though Haswell names this register PIPE_CLK_SEL, it will be
renamed to TRANS_CLK_SEL in the future, so let's just start using the
real name that makes more sense and avoids misusage.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previous patch "drm/i915: add basic Haswell DP link train bits"
implemented the basic structure to set the voltage levels and training
patterns. This patch adds the higher-level bits that are part of the
mode set sequence and hot plug.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
