DMA is opt-in for this driver. So, we can't use deferred probing for
requesting DMA channels in probe, because our driver would get endlessly
deferred if DMA support is compiled in AND the DMA driver is missing.
Because we can't know when the DMA driver might show up, we always try
again when a DMA transfer would be possible. The downside is that there
is more overhead for setting up PIO transfers under the above scenario.
But well, having DMA enabled and the proper DMA driver missing looks
like a broken or test config anyhow.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Refactor DMA setup to keep the errno so we can implement better
deferred probe support in the next step.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Originally, the I2C controller supported by the i2c-mv64xxx driver
requires a lot of software support: an interrupt is generated at each
step of an I2C transaction (after the start bit, after sending the
address, etc.) and the driver is in charge of re-programming the I2C
controller to do the next step of the I2C transaction. This explains
the fairly complex state machine that the driver has.
On Marvell Armada XP and later processors (Armada 375, 38x, etc.), the
I2C controller was extended with a part called the "I2C Bridge", which
allows to offload the I2C transaction completely to the
hardware. Initial support for this mechanism was added in commit
930ab3d403 ("i2c: mv64xxx: Add I2C Transaction Generator support").
However, the implementation done in this commit has two related
issues, which this commit fixes by completely changing how the offload
implementation is done:
* SMBus read transfers, where there is one write to select the
register immediately followed in the same transaction by one read,
were making the processor hang. This was easier visible on the
Marvell Armada XP WRT1900AC platform using a driver for an I2C LED
controller, or on other Armada XP platforms by using a simple
'i2cget' command to read an I2C EEPROM.
* The implementation was based on the fact that the offload engine
was re-programmed to transfer each message of an I2C xfer: this
meant that each message sent with the offload engine was starting
with a normal I2C start sequence. However, the I2C subsystem
assumes that all messages belonging to the same xfer will use the
so-called "repeated start" so that the entire I2C xfer is seen as
one transfer by the I2C devices and cannot be interrupt by other
I2C masters on the same bus.
In fact, the "I2C Bridge" allows to offload three types of xfer:
- xfer of one write message
- xfer of one read message
- xfer of one write message followed by one read message
For all other situations, we have to fallback to not using the "I2C
Bridge" in order to get proper I2C semantics.
Therefore, this commit reworks the offload implementation to put it
not at the message level, but at the xfer level: in the
mv64xxx_i2c_xfer() function, we decide if the transaction can be
offloaded (in which case it is handled by the
mv64xxx_i2c_offload_xfer() function), or otherwise it is handled by
the slow path (implemented in the existing mv64xxx_i2c_execute_msg()).
This allows to simplify the state machine, which no longer needs to
have any state related to the offload implementation: the offload
implementation is now completely separated from the slow path (with
the exception of the interrupt handler, of course).
In summary:
- mv64xxx_i2c_can_offload() will analyze an I2C xfer and decided of
the "I2C Bridge" can be used to offload it or not.
- mv64xxx_i2c_offload_xfer() will actually program the "I2C Bridge"
to offload one xfer (of either one or two messages), and block
using mv64xxx_i2c_wait_for_completion() until the xfer completes.
- The interrupt handler mv64xxx_i2c_intr() is modified to push the
offload related code to a separate function,
mv64xxx_i2c_intr_offload(). It will take care of reading the
received data if needed.
This commit was tested on:
- Armada XP OpenBlocks AX3-4 (EEPROM on I2C and RTC on I2C)
- Armada XP WRT1900AC (LED controller on I2C)
- Armada XP GP (EEPROM on I2C)
Fixes: 930ab3d403 ("i2c: mv64xxx: Add I2C Transaction Generator support")
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[wsa: fixed checkpatch warnings]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
There are two new drivers, one for the BCM2835 (Raspberry Pi) and one
used in conjunction with the LCD controller on various Atmel SoCs. The
Samsung PWM driver can now be built for 64-bit ARM (Exynos7).
A couple of fixes have been applied to the FTM PWM driver and system
sleep support was added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jD3K
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There are two new drivers, one for the BCM2835 (Raspberry Pi) and one
used in conjunction with the LCD controller on various Atmel SoCs.
The Samsung PWM driver can now be built for 64-bit ARM (Exynos7).
A couple of fixes have been applied to the FTM PWM driver and system
sleep support was added"
* tag 'pwm/for-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: atmel-hlcdc: add at91sam9x5 and sama5d3 errata handling
pwm: ftm: Add Power Management support for FTM PWM
pwm: ftm: Add regmap rbtree type cache support
pwm: ftm: Correctly track usage count
pwm: samsung: Allow Samsung PWM driver to be enabled on Exynos7
pwm: add DT bindings documentation for atmel-hlcdc-pwm driver
pwm: add support for atmel-hlcdc-pwm device
pwm: Add BCM2835 PWM driver
Pull input subsystem updates from Dmitry Torokhov:
"Two new drivers for Elan hardware (for I2C touchpad and touchscreen
found in several Chromebooks and other devices), a driver for Goodix
touch panel, and small fixes to Cypress I2C trackpad and other input
drivers.
Also we switched to use __maybe_unused instead of gating suspend/
resume code with #ifdef guards to get better compile coverage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: gpio_keys - fix warning regarding uninitialized 'button' variable
Input: add support for Elan eKTH I2C touchscreens
Input: gpio_keys - fix warning regarding uninitialized 'irq' variable
Input: cyapa - use 'error' for error codes
Input: cyapa - fix resuming the device
Input: gpio_keys - add device tree support for interrupt only keys
Input: amikbd - allocate temporary keymap buffer on the stack
Input: amikbd - fix build if !CONFIG_HW_CONSOLE
Input: lm8323 - missing error check in lm8323_set_disable()
Input: initialize device counter variables with -1
Input: initialize input_no to -1 to avoid subtraction
Input: i8042 - do not try to load on Intel NUC D54250WYK
Input: atkbd - correct MSC_SCAN events for force_release keys
Input: cyapa - switch to using managed resources
Input: lifebook - use "static inline" instead of "inline" in lifebook.h
Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resume
Input: mouse - use __maybe_unused instead of ifdef around suspend/resume
Input: misc - use __maybe_unused instead of ifdef around suspend/resume
Input: cap11xx - support for irq-active-high option
Input: cap11xx - add support for various cap11xx devices
...
* Add device tree support for DoC3
* SPI NOR:
Refactoring, for better layering between spi-nor.c and its driver users
(e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
* NAND
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing purposes
Add ATO manufacturer ID
A few odd driver fixes
* MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
* nandsim: Support longer ID byte strings
And more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gDW8
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Summary:
- Add device tree support for DoC3
- SPI NOR:
Refactoring, for better layering between spi-nor.c and its
driver users (e.g., m25p80.c)
New flash device support
Support 6-byte ID strings
- NAND:
New NAND driver for Allwinner SoC's (sunxi)
GPMI NAND: add support for raw (no ECC) access, for testing
purposes
Add ATO manufacturer ID
A few odd driver fixes
- MTD tests:
Allow testers to compensate for OOB bitflips in oobtest
Fix a torturetest regression
- nandsim: Support longer ID byte strings
And more"
* tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd: (63 commits)
mtd: tests: abort torturetest on erase errors
mtd: physmap_of: fix potential NULL dereference
mtd: spi-nor: allow NULL as chip name and try to auto detect it
mtd: nand: gpmi: add raw oob access functions
mtd: nand: gpmi: add proper raw access support
mtd: nand: gpmi: add gpmi_copy_bits function
mtd: spi-nor: factor out write_enable() for erase commands
mtd: spi-nor: add support for s25fl128s
mtd: spi-nor: remove the jedec_id/ext_id
mtd: spi-nor: add id/id_len for flash_info{}
mtd: nand: correct the comment of function nand_block_isreserved()
jffs2: Drop bogus if in comment
mtd: atmel_nand: replace memcpy32_toio/memcpy32_fromio with memcpy
mtd: cafe_nand: drop duplicate .write_page implementation
mtd: m25p80: Add support for serial flash Spansion S25FL132K
MTD: m25p80: fix inconsistency in m25p_ids compared to spi_nor_ids
mtd: spi-nor: improve wait-till-ready timeout loop
mtd: delete unnecessary checks before two function calls
mtd: nand: omap: Fix NAND enumeration on 3430 LDP
mtd: nand: add ATO manufacturer info
...
Pull security subsystem fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: remove a bogus NULL check
ima: Fix build failure on powerpc when TCG_IBMVTPM dependencies are not met
KEYS: Fix stale key registration at error path
Pull fuse update from Miklos Szeredi:
"The first part makes sure we don't hold up umount with pending async
requests. In addition to being a cleanup, this is a small behavioral
change (for the better) and unlikely to break anything.
The second part prepares for a cleanup of the fuse device I/O code by
adding a helper for simple request submission, with some savings in
line numbers already realized"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use file_inode() in fuse_file_fallocate()
fuse: introduce fuse_simple_request() helper
fuse: reduce max out args
fuse: hold inode instead of path after release
fuse: flush requests on umount
fuse: don't wake up reserved req in fuse_conn_kill()
make sure 'value' is not null. otherwise __ceph_setxattr will remove
the extended attribute.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
mksnap reply only contain 'target', does not contain 'dentry'. So
it's wrong to use req->r_reply_info.head->is_dentry to detect traceless
reply.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Probably this code was syncing a lot more often then intended because
the do_sync variable wasn't set to zero.
Cc: stable@vger.kernel.org # v3.11+
Fixes: c62988ec09 ('ceph: avoid meaningless calling ceph_caps_revoking if sync_mode == WB_SYNC_ALL.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
pagelist.h needs to include linux/types.h and asm/byteorder.h and not
rely on other headers pulling yet another set of headers.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
After converting inline data to normal data, client need to flush
the new i_inline_version (CEPH_INLINE_NONE) to MDS. This commit makes
cap messages (sent to MDS) contain inline_version and inline_data.
Client always converts inline data to normal data before data write,
so the inline data length part is always zero.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Before any data write, convert inline data to normal data and set
i_inline_version to CEPH_INLINE_NONE. The OSD request that saves
inline data to object contains 3 operations (CMPXATTR, WRITE and
SETXATTR). It compares a xattr named 'inline_version' to prevent
old data overwrites newer data.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
we can't use getattr to fetch inline data while holding Fr cap,
because it can cause deadlock. If we need to sync read inline data,
drop cap refs first, then use getattr to fetch inline data.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
we can't use getattr to fetch inline data after getting Fcr caps,
because it can cause deadlock. The solution is try bringing inline
data to page cache when not holding any cap, and hope the inline
data page is still there after getting the Fcr caps. If the page
is still there, pin it in page cache for later IO.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Add a new parameter 'locked_page' to ceph_do_getattr(). If inline data
in getattr reply will be copied to the page.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Request reply and cap message can contain inline data. add inline data
to the page cache if there is Fc cap.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
allow specifying position of extent operation in multi-operations
osd request. This is required for cephfs to convert inline data to
normal data (compare xattr, then write object).
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@redhat.com>
Add CEPH_OSD_OP_CREATE support. Also change libceph to not treat
CEPH_OSD_OP_DELETE as an extent op and add an assert to that end.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@redhat.com>
CEPH_OSD_OP_DELETE is not an extent op, stop treating it as such. This
sneaked in with discard patches - it's one of the three osd ops (the
other two are CEPH_OSD_OP_TRUNCATE and CEPH_OSD_OP_ZERO) that discard
is implemented with.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Current snaphost code does not properly handle moving inode from one
empty snap realm to another empty snap realm. After changing inode's
snap realm, some dirty pages' snap context can be not equal to inode's
i_head_snap. This can trigger BUG() in ceph_put_wrbuffer_cap_refs()
The fix is introduce a global empty snap context for all empty snap
realm. This avoids triggering the BUG() for filesystem with no snapshot.
Fixes: http://tracker.ceph.com/issues/9928
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@redhat.com>
There were two places we were assigning version in host byte order
instead of network byte order.
Also in MSG_CLIENT_SESSION we weren't setting compat_version in the
header to reflect continued compatability with older MDSs.
Fixes: http://tracker.ceph.com/issues/9945
Signed-off-by: John Spray <john.spray@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
2 bytes of what was reserved space is now used by userspace for the
compat_version field.
Signed-off-by: John Spray <john.spray@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Session key is required when calculating message signature. Save the session
key in authorizer, this avoid lookup ticket handler for each message
Signed-off-by: Yan, Zheng <zyan@redhat.com>
The functions ceph_put_snap_context() and iput() test whether their
argument is NULL and then return immediately. Thus the test around the
call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[idryomov@redhat.com: squashed rbd.c hunk, changelog]
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
After creating/deleting/renaming file, offsets of sibling dentries may
change. So we can not use cached dentries to satisfy readdir. But we can
still use the cached dentries to conclude -ENOENT for lookup.
This patch introduces a new inode flag indicating if child dentries are
ordered. The flag is set at the same time marking a directory complete.
After creating/deleting/renaming file, we clear the flag on directory
inode. This prevents ceph_readdir() from using cached dentries to satisfy
readdir syscall.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Use kvfree() from linux/mm.h instead, which is identical. Also fix the
ceph_buffer comment: we will allocate with kmalloc() up to 32k - the
value of PAGE_ALLOC_COSTLY_ORDER, but that really is just an
implementation detail so don't mention it at all.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
When a lock operation is interrupted, current code sends a unlock request to
MDS to undo the lock operation. This method does not work as expected because
the unlock request can drop locks that have already been acquired.
The fix is use the newly introduced CEPH_LOCK_FCNTL_INTR/CEPH_LOCK_FLOCK_INTR
requests to interrupt blocked file lock request. These requests do not drop
locks that have alread been acquired, they only interrupt blocked file lock
request.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Packard Bell EasyNote MX65 with AD1986A codec needs a few fixups,
namely, the pin config overrides to set only the known I/O pins and
the EAPD has to be turned on. In addition, add stereo mix input
forcibly for avoiding the weird KDE behavior by this update.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88251
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for two XMOS based DACs from Matrix Audio:
- X-Sabre
- Mini-i Pro
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Audio subsystem clocks are located in separate block. On Exynos 5420 if
clock for this block (from main clock domain) 'mau_epll' is gated then
any read or write to audss registers will block.
This kind of boot hang was observed on Arndale Octa and Peach Pi/Pit
after introducing runtime PM to pl330 DMA driver. After that commit the
'mau_epll' was gated, because the "amba" clock was disabled and there
were no more users of mau_epll.
The system hang on one of steps:
1. Disabling unused clocks from audss block.
2. During audss GPIO setup (just before probing i2s0 because
samsung_pinmux_setup() tried to access memory from audss block which was
gated.
Add a workaround for this by enabling the 'mau_epll' clock in probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
In filename__read_build_id, phdr points to memory in buf, which gets realloced
before a call to fseek that uses phdr->p_offset. This change stores the value
of p_offset before buf is realloced, so the fseek can use the value safely.
Signed-off-by: Mitchell Krome <mitchellkrome@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20141216021612.GA7199@mitchell
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To replace equivalent code used in the mmap_pages command line
parameter handling in tools/perf.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-i44zs02xt4zexfxywpklo7km@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If /proc/sys/kernel/perf_event_mlock_kb is not (power of 2 + PAGE_SIZE_in_kb)
and we let the perf tools do mmap length autosizing based on that, then, for
non-CAP_IPC_LOCK users when /proc/sys/kernel/perf_event_paranoid is > -1, then
we get an -EINVAL that ends up in:
[acme@ssdandy linux]$ trace usleep 1
Invalid argument
[acme@ssdandy linux]$ perf record usleep 1
failed to mmap with 22 (Invalid argument)
After this fix:
[acme@ssdandy linux]$ trace usleep 1
<SNIP>
0.806 ( 0.006 ms): munmap(addr: 0x7f7e4740a000, len: 66467) = 0
0.869 ( 0.002 ms): brk( ) = 0x7bb000
0.873 ( 0.003 ms): brk(brk: 0x7dc000 ) = 0x7dc000
0.877 ( 0.001 ms): brk( ) = 0x7dc000
0.953 ( 0.058 ms): nanosleep(rqtp: 0x7fff26ab9420 ) = 0
0.959 ( 0.000 ms): exit_group(
[acme@ssdandy linux]$ perf record usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.017 MB perf.data (~759 samples) ]
[acme@ssdandy linux]$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-6p6l5ou6jev6o7ymc4nn1n2a@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Will be used to make sure we pass a power of two when automatically
setting up the perf_mmap addr range length, as the kernel code
validating input on /proc/sys/kernel/perf_event_mlock_kb accepts any
integer, if we plain use it to set up the mmap lenght, we may get an
EINVAL when passing a non power of two.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-zflvep0q01dmkruf4o291l4p@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Will be used when adopting rounddown_pow_of_two.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-9m0tt5300q1ygv51hejjas82@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So that we better mirror the kernel sources and make it available for
other tools.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-mvfu6x753tksnto3t6412m93@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In preparation for moving linux/bitops.h from tools/perf/util/ to
tools/include/.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-2wuk8vahl7voz0ie55f07c9k@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To match the Linux kernel source code structure from where this code came from.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-fkbma1h04ki0zzdmp0dpgfyy@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>