Hook up the R-Car M3-N AVB device to IPMMU-DS0 16 as described in
the data sheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The "official" Condor boards have always been wired to mount NFS via
GEther, not EtherAVB -- the boards resoldered for EtherAVB were local
to Cogent Embedded, so we've been having an unpleasant situation where
a "normal" Condor board still can't mount NFS (unless an EtherAVB PHY
extension board is plugged in). Switch from EtherAVB to GEther at last!
Fixes: 8091788f3d ("arm64: dts: renesas: condor: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
hscif2 has 4 dmas, but has only 2 dma-names.
This patch add missing dma-names.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e0f0bda793 ("arm64: dts: renesas: r8a7795: sort subnodes
of the soc node")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device nodes for SCIF-{0,1,3,4,5} serial ports to
the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe MSIOF in the R8A779{7|8}0 device trees.
The DMA props are omitted for R8A77980 as the RT-DMAC isn't supported
(yet?)...
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The M3-N (r8a77965) platform has one LVDS encoder connected to the DU.
Add the corresponding DT node and wire it up.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe THS/CIVM in the R8A77980 device trees.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe THS/CIVM in the R8A77970 device tree.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe PWMs in the R8A779{7|8}0 device trees.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car E3, which serves external IRQ pins IRQ[0-5].
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
commit 2d87dc0e5b ("arm64: dts: renesas: r8a7795: Add address
properties to rcar_sound port nodes") added missing #address-cells
and #size-cells for sound ports.
But, these are based on platform, not on SoC. This patch cleanups it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for both RZ/G2M CAN channels.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on a similar patch of the R8A7796 device tree
by Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds LVDS decoder, HDMI encoder and connector for the Draak board.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Draak
board, hook them up in DT.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the LVDS decoder, HDMI encoder, VGA encoder and HDMI and VGA
connectors, and wire up the display-related nodes with clocks, pinmux
and regulators.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Ebisu
board, hook them up in DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77995 D3 platform has 2 LVDS channels connected to the DU.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[uli: moved lvds* into the soc node, added PM domains, resets]
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R8A77990 (E3) platform has one RGB output and two LVDS outputs
connected to the DU. Add the DT nodes for the DU, LVDS encoders and
supporting VSP and FCP.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe TPU in the R8A779{7|8}0 device trees.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car Gen3 SoCs need to enable/deassert clocks/resets of both usb 2.0
host (included phy) and peripheral. Otherwise, other side device
cannot work correctly. So, this patch revises properties of clocks
and resets. After that, each device driver can enable/deassert
clocks/resets by its self.
Notes:
- To work the renesas_usbhs driver correctly when host side drivers
are disabled and the renesas_usbhs driver doesn't have multiple
clock management, this patch doesn't change the order of the clocks
property in each hsusb node.
- This patch doesn't have any side-effects even if the renesas_usbhs
driver doesn't have reset_control and multiple clock management.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It can't boot without bootargs settings on Uboot on ulcb board.
This patch adds missing default bootargs.
ulcb BSP can overwrite it by own UBoot settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe CMTs in the R8A779{7|8}0 device trees.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC and EEPROM can operate at 400kHz, so use this speed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car V3H hook up SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS1 to match
information in the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car E3 hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car H3.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.
Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The thermal device is supposed to be always enabled. As the default
value of the status property is "okay", there is no need to make this
explicit in SoC-specific .dtsi files where no override is involved.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a77965 has a single FDP1 instance.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Device nodes with unit addresses are sorted by unit address,
- Device nodes without unit addresses and references are sorted
alphabetically.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Successfully tested on H3 ES1.0 and ES2.0, M3-W ES1.0, and M3-N ES1.0.
Even previously stubborn cards work fine. Transfer rates were >60MB/s.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers, incl. clocks, power
domains, and resets properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK, and describe the clock
inputs for the Baud Rate Generator for External Clock (BRG) for SCIF2,
which can increase serial clock accuracy.
The presence of the SCIF_CLK crystal and its clock frequency depend on
the actual board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Enhance patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the SoC-specific CPG/MSSR include file to allow future use of
R8A77990_CLK_* symbols.
Replace the hardcoded power domain indices by R8A77990_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The comments describing the non-default switch settings to use SATA are
confusing: 'Off' refers to the switch position, not to the MD12 logic
value, while the parentheses suggest otherwise. Rephrase to fix this.
Fixes: bec000784d5bb571 ("arm64: dts: renesas: salvator-xs: enable SATA")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: updated for a few new cases]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is based on the existing KF device tree sources:
$ ls -1 arch/arm64/boot/dts/renesas/*-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-kf.dts
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dts
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable PCIe PHY and PCIEC and specify the PCIe bus clock for the Condor
board.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the PCIe PHY, PCIEC, and PCIe bus clock in the R8A77980 device
tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb3.0 phy, host and function device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb dmac and hsusb device nodes on RZ/G2M SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add FCPF and FCPV instances to the r8a774a1 dtsi, similarly
to what was done for the r8a7796 with commit 41dbbf0c5b
("arm64: dts: r8a7796: Add FCPF and FCPV instances"),
commit 69490bc966 ("arm64: dts: renesas: r8a7796: Point
FDP1 via FCPF to IPMMU-VI0"), and commit cef942d0bd ("arm64:
dts: renesas: r8a7796: Point VSPI via FCPVI to IPMMU-VC0").
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G2M SoC (a.k.a. R8A774A1).
This work is based on similar work done on the R8A7796 SoC
by Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PWM[0123456] device nodes to the RZ/G2M (a.k.a R8A774A1)
device tree.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds definitions for L2 cache for the Cortex-A53 CPU
cores (512 KiB in size, organized as 32 KiB x 16 ways), adds
Cortex-A53 CPU cores (setting a total of 6 cores, 2 x Cortex-A57
+ 4 x Cortex-A53), and finally enables the performance monitor
unit for the Cortex-A53 cores on the R8A774A1 SoC.
Based on work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all MSIOF SPI controllers on RZ/G2M SoC.
Based on several similar patches of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>
and Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add thermal support for R8A774A1 (RZ/G2M) SoC.
Based on the work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-6] and IIC Bus Interface for DVFS (IIC for DVFS)
devices nodes to the r8a774a1 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO device nodes to the DT of the r8a774a1 SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the SoC specific part of the Ethernet AVB
device tree node.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the Interrupt Controller for External Devices
(INTC-EX) on RZ/G2M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2M SCIF and HSCIF serial ports,
incl. clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor/V3HSK board dependent parts of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the eMMC chip support for the V3M Started Kit board.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 part of the MMC0 (SDHI2) device node.
Based on the original (and large) patches by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds OPPs table for CA57{0,1} cpu devices
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
[simon: do not give nodes unit names as they have no bus addresses]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Allow the bare M3-N-based ULCB board to boot.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 HW manual rev1.00, R-Car M3-N has two CAN
interfaces, similar to H3, M3-W and other SoCs from the same family.
Add CAN placeholder nodes to avoid below DTC errors:
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:19.1-6 Label or path can0 not found
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:25.1-6 Label or path can1 not found
These errors occur *after* the addition of r8a77965-m3nulcb-kf.dts.
Fix them beforehand.
CAN support is inspired from below commits:
- v4.7 commit 308b7e4ba6 ("arm64: dts: r8a7795: Add CAN support")
- v4.11 commit 909c162524 ("arm64: dts: r8a7796: Add CAN support")
- v4.12 commit bec0948e81 ("arm64: dts: r8a7796: Add reset control properties")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[simon: make placeholder minimal by only including reg property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car M3-N hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car M3-W.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/G2M SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ensure that the ADV748x device addresses do not conflict, and group them
together (visually in i2cdetect)
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the CSI2 and VIN (and their interconnections) in the R8A77980
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the nodes to enable SATA. Note that MD12 (SW12-7) must be switched
off for that to work.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SATA controller node for the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: rebased to upstream base]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CAN clock node should precede the "cpus" node in the R8A779{7|8}0
device trees, according to the alphanumeric node sorting rule...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IPMMU nodes should follow the GEther node, not the CAN-FD node,
according to the <unit-address> part of the startng IPMMU-DS1 node.
While moving the nodes, also do sort them by label alphanumerically...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PWM device nodes and enables PWM3 and PWM5 for
R-Car E3 Ebisu board. These devices are used for backlight control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the performance monitor unit (PMU) for the Cortex-A53 cores in
the R8A77980 SoC's device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the r8a7795 and r8a7796 device trees over to the new model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1
following the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Browsing the DTS for all the R-Car SoCs with similar part numbers
makes my head hurt, so to improve the user friendliness of the
DTS code base include R-Car product name in each DTSI file.
Product names are derived from
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe RWDT in the R8A77980 SoC device tree.
Enable RWDT on the Condor and V3H Starter Kit boards.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the INTC-EX interrupt controller in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds and USB3.0 host device node and enable it for
R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device nodes for SCIF {0,1,3,4,5} and all HSCIF serial
ports, incl. clocks, power domain and DMAs.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU device nodes for the R-Car M3-N (r8a77965),
V3H (r8a77980) and E3 (r8a77990) SoCs.
* The r8a77965 IPMMU is quite similar to r8a7796 however VP0
has been added and PV1 has been removed. Also the IMSSTR
bit assignment has been reworked.
* The r8a77980 IPMMU is quite similar to r8a77970 however VC0
has been added. The IMSSTR bit assignment has also been
reworked. Power domains are also quite different however the
the documentation is rather unclear about this topic.
Until we know better VC0 gets assigned to R8A77980_PD_ALWAYS_ON.
* The r8a77990 IPMMU is similar to r8a77995. Power domains are
however different and the public documentation is still unclear.
Based on preliminary information from the hardware team the R-Car E3
SoC comes with an IPMMU-VP0 device in an Always-on power domain and
the IPMMU-VC0 is placed as expected in the A3VC power domain.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The labels for RWDT device node were named as 2 types now:
- wdt0: r8a7795, r8a7796, r8a77965.
- rwdt: r8a77970, r8a77990, r8a77995.
To be made consistent, this patch unifis the labels as the hardware
name "rwdt".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
HSCIF is superior to SCIF (larger FIFOs, more accurate and wider
supported range of bitrates).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This node is just a placeholder but fills that function better if it does
not trigger build warnings. This update satisfies the requirement that
nodes with #address-cells/#size-cells properties have more than one child
node.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (graph_child_address): /soc/sound@ec500000/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (graph_child_address): /soc/sound@ec500000/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
With recent dtc and W=1:
...salvator-x.dtb: Warning (graph_port): /soc/i2c@e66d8000/video-receiver@70/port@10: graph node unit address error, expected "a"
...salvator-x.dtb: Warning (graph_port): /soc/i2c@e66d8000/video-receiver@70/port@11: graph node unit address error, expected "b"
Unit addresses are always hexadecimal (without prefix), while the bases
of reg property values depend on their prefixes.
Fixes: 908001d778 ("arm64: dts: renesas: salvator-common: Add ADV7482 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car E3 does not have the Stream Buffer for EtherAVB-IF (STBE).
Note that the RAVB driver does not use this region.
Fixes: 913a78b575 ("arm64: dts: renesas: r8a77990: Add EthernetAVB device nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pin control for HSCIF1, and supports connection with
Debug Serial-1 (CN26) on Salvator boards.
SCIF1 and HSCIF1 are sharing the pins connected to Debug Serial-1 (CN26)
on Salvator boards, and it is necessary to ensure that either SCIF1 or
HSCIF1 is enabled, not both.
As for the default of this DeviceTree, SCIF1 is connected.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Add missing "uart-has-rtscts"]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the interconnected FCPVD0, VSPD0, DU, and LVDS0 devices in the
R8A77980 device tree...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify Ethernet PHY IRQs in the Condor/V3HSK board device trees, now that
we have the GPIO support (previously phylib had to resort to polling).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PCIe{0,1} device nodes to R8A77965 SoC.
Based on a similar patches of the R8A7796 device tree
by Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VSPD and FCPVD nodes have overlapping register ranges, as the FCPVD
devices are mapped in the memory range usually used by the VSP LUT and
CLU, which are not present in the VSPD. Fix this by shortening the VSPD
registers range to 0x5000.
Fixes: 9f8573e38a ("arm64: dts: renesas: r8a7795: Add VSP instances")
Fixes: 291e0c4994 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
Fixes: f06ffdfbdd ("arm64: dts: r8a7796: Add VSP instances")
Fixes: b4f92030d5 ("arm64: dts: renesas: r8a77970: add VSPD support")
Fixes: 295952a183 ("arm64: dts: renesas: r8a77995: add VSP instances")
Fixes: 85cb322921 ("arm64: dts: renesas: r8a77965: Add VSP instances")
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe all 6 GPIO controllers in the R8A77980 device tree.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB2.0 PHY and Host(EHCI/OHCI) nodes and
enables them for R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
R-Car E3 (r8a77990) SoC, and adjust the interrupt delivery masks for ARM
Generic Interrupt Controller and Architectured Timer.
Based on a patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the
R8A77990 SoC, and enable the watchdog on the Ebisu board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed 2 commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Condor board dependent part of the I2C0 device node.
The I2C0 bus is populated by 2 ON Semiconductor PCA9654 I/O expanders
and Analog Devices ADV7511W HDMI transmitter (but we're only describing
the former chips now).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 parts of the I2C[0-5] device nodes.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Any of the following devices connected to I2C ch4 of the Salvator-X(S)
boards will operate at 400 kHz:
PCA9654, 9FGV0841, ADV7482WBBCZ, MAX9611, 5P49V5923, 5P49V6901A
This patch updates the clock frequency to 400 KHz.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: squashed commits into one]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds definitions for configuration of the power-source,
drive-strength, etc... for the SD2_DS pin for Salvator-X(S) and ULCB
boards.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: fixed for ULCB boards, too]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on a similar patch of the R8A7796 device tree
by Ulrich Hecht <ulrich.hecht+renesas@gmail.com>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded clock indices by R8A77965_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add bindings for CryptoCell instance in the SoC.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the Renesas
R-Car M3-N (R8A77965) SoC.
Based on a similar patch of the R8A7796 device tree
by Geert Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the V3H Starter Kit board dependent part of the GEther device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77980 part of the GEther device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: add resets property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for 3 more Cortex-A53 CPU cores; adjust the interrupt
delivery masks for the ARM GIC and Architectured Timer.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: corrected whitespace]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe HDMI input connector and ADV7612 HDMI decoder installed on
R-Car Gen3 Draak board.
The video signal routing to the HDMI decoder to the video input interface
VIN4 is multiplexed with CVBS input path, and enabled/disabled through
on-board switches SW-49, SW-50, SW-51 and SW-52.
As the default board switches configuration connects CVBS input to VIN4,
leave the HDMI decoder unconnected in DTS.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe CVBS video input through analog video decoder ADV7180
connected to video input interface VIN4.
The video input signal path is shared with HDMI video input, and
selected by on-board switches SW-53 and SW-54 with CVBS input selected
by the default switches configuration.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The compat string renesas,gpio-rcar has been deprecated since v4.14,
the same release that r8a77990 SoC support was added. Thus
renesas,gpio-rcar can safely be removed without any risk of behaviour
changes between old and new mainline kernels and DTBs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add power domain information to the R-Car D3 IPMMU device nodes.
As specified by the data sheet, all the IPMMU devices are always on.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Salvator boards use an ADV7482 receiver for HDMI and CVBS inputs.
Provide ADV7482 node on the i2c4 bus, along with connectors for the
hdmi and cvbs inputs, and link to the csi20 and csi40 nodes as outputs.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas H3 ES1.0 have one extra CSI-2 node, CSI21 which is not present
for later ES versions of H3.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables EthernetAVB for r8a77990 Ebisu board.
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds EthernetAVB node for r8a77990 (R-Car E3).
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds GPIO nodes for r8a77990 (R-Car E3).
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[simon: dropped use of deprecated "renesas,gpio-rcar"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the V3H Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the R8A77980 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...
Fixes: bf6f90832f ("arm64: dts: renesas: r8a77980: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the R8A77970 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...
Fixes: bea2ab136e ("arm64: dts: renesas: r8a77970: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add resets property to CAN-FD node to describe it in the reset topology of
on-SoC devices. This allows to reset the CAN-FD device using the Reset
Controller API.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the performance monitor unit for the Cortex-A53 cores on the
R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the second Cortex-A53 CPU core on the Renesas
R-Car V3M (r8a77970) SoC, and adjust the interrupt delivery masks for
ARM Generic Interrupt Controller and Architectured Timer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a77965 SoC.
Based on several similar patches of the R8A7796 device tree
by Simon Horman <horms+renesas@verge.net.au>.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On the R-Car Starter Kit Premier/Pro, all of the DDR0, DDR1, DDR0C, and
DDR1C power rails need to be kept powered when backup mode is enabled.
Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV
PMIC node.
The accessory power switch (SW8) is a momentary switch, hense specify
"rohm,rstbmode-pulse".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Salvator-X(S), all of the DDR0, DDR1, DDR0C, and DDR1C power rails
need to be kept powered when backup mode is enabled. Reflect this in
the "rohm,ddr-backup-power" property for the BD9571MWV PMIC node.
The accessory power switch (SW23) is a toggle switch, hence specify
"rohm,rstbmode-level".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
