* 'for-linus/i2c' of git://git.fluff.org/bjdooks/linux:
i2c-stu300: off by one issue
i2c-pnx: Add stop conditions for end of transfer
i2c-pnx: Limit maximum divider to 1023
i2c-omap: fix OOPS in omap_i2c_unidle() during probe
i2c-imx: fix error handling
When the dt3155 driver is built-in (not as a loadable module),
these build errors happen:
drivers/staging/dt3155/dt3155_drv.c:1047: error: implicit declaration of function 'request_irq'
drivers/staging/dt3155/dt3155_drv.c:1048: error: 'IRQF_SHARED' undeclared (first use in this function)
drivers/staging/dt3155/dt3155_drv.c:1048: error: 'IRQF_DISABLED' undeclared (first use in this function)
drivers/staging/dt3155/dt3155_drv.c:1091: error: implicit declaration of function 'free_irq'
so remove the #ifdef MODULE check since it's not needed. Also remove
the CONFIG_PCI check since the Kconfig file already requires that.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Scott Smedley <ss@aao.gov.au>
Tested-by: Jan III Sobieski <jan3sobi3ski@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We leak memory if "--dry-run" is not supported by the peer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
JFFS2 does not appear to set s_bdi anywhere. And as of 32a88aa1,
__sync_filesystem() will return 0 if s_bdi is not set. As a result,
sync_fs() is never called for jffs2 and whatever remains in the wbuf
will not make it to the device.
Fix that up by assigning the mtd bdi.
Signed-off-by: Jörn Engel <joern@logfs.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
pl061_direction_output doesn't set value of gpio to value passed to it.
This patch sets value of GPIO pin to requested value after changing direction
to OUT.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL061 driver is using set_irq_chip_data and get_irq_chip_data for real
irq lines. It must be using *_irq_data functions instead. As chip_data
is used by interrupt controllers also, which makes vic write at incorrect
addresses.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add new driver to use tethering with an iPhone device. After initial submission,
apply fixes to fit the new driver into the kernel standards.
There are still a couple of minor (almost cosmetic-level) issues, but the driver
is fully functional right now.
Signed-off-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: Diego Giagio <diego@giagio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered an issue that not to link up on cxgb3 fabric.
I bisected and found that this regression was introduced by
0f07c4ee8c.
Correct to pass phy_addr to cphy_init() at t3_xaui_direct_phy_prep().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL pointer dereference in ks8851_tx_work by checking if dequeued
list is already empty before writing the packet to TX FIFO
Unable to handle kernel NULL pointer dereference at virtual address 00000050
PC is at ks8851_tx_work+0xdc/0x1b0
LR is at wait_for_common+0x148/0x164
pc : [<c01c0df4>] lr : [<c025a980>] psr: 20000013
Backtrace:
ks8851_tx_work+0x0/0x1b0
worker_thread+0x0/0x190
kthread+0x0/0x90
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the stats counter calculation in 3c574_cs, similar
to the method used in 3c589_cs. This corrects the contents
of the counter on tests using a "Megahertz 574B" card.
[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ems_usb_probe(), a pointer is dereferenced after making sure it is NULL...
This patch replaces netdev->dev.parent with &intf->dev in dev_err() calls to
avoid this.
Signed-off-by: "Hans J. Koch" <hjk@linutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: allow 4 coldfire serial ports
m68knommu: fix coldfire tcdrain
m68knommu: remove a duplicate vector setting line for 68360
Fix m68k-uclinux's rt_sigreturn trampoline
m68knommu: correct the CC flags for Coldfire M5272 targets
uclinux: error message when FLAT reloc symbol is invalid, v2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
mc13783-regulator: fix a memory leak in mc13783_regulator_remove
regulator: Let drivers know when they use the stub API
pcmcia_dev_present is in and by itself buggy. Add a note specifying
why it is broken, and replace the broken locking -- taking a mutex
is a bad idea in IRQ context, from which this function is rarely
called -- by an atomic_t.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fix tcdrain on coldfire uarts.
Currently with coldfire uarts tcdrain returns without waiting for txempty,
because (tx)fifosize is 0. Fix that and call uart_update_timeout when
setting the baud rate, otherwise tcdrain will wait for an half our :)
Also constify mcf_uart_ops.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: fix error handling in cm4000_cs.c
drivers/pcmcia: Add missing local_irq_restore
serial_cs: MD55x support (PCMCIA GPRS/EDGE modem) (kernel 2.6.33)
pcmcia: avoid late calls to pccard_validate_cis
pcmcia: fix ioport size calculation in rsrc_nonstatic
pcmcia: re-start on MFC override
pcmcia: fix io_probe due to parent (PCI) resources
pcmcia: use previously assigned IRQ for all card functions
Drivers may use vblank calls now (e.g. drm_vblank_off) in their unload
paths, so don't clean up the vblank related structures until after
driver unload.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With many large drives and small chunk sizes it is possible
to create a RAID5 with more than 2^31 chunks. Make sure this
works.
Reported-by: Brett King <king.br@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
If we don't find the correct rate, we want to end the loop with "i"
pointing to the last element in the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a stop condition bit flag to the last byte in the transfer.
This will generate an extra clock to handle the stop condition
and prevent devices from staying in an ACK'd state.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Limit maximum divider to 0x3ff to divider computations. On high I2C
parent clock rates, the divider can exceed 0x3ff. This will help
prevent some very odd clock rates.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
- Return -ETIMEDOUT on bus busy error
- Fix timeout test "time_after(jiffies, orig_jiffies + HZ / 1000)" :
By default, HZ=100 on arm. This means that this test has no chances to
work and may result in a dead loop. Set timeout to 500ms.
- Don't try to send a new message if we failed to transmit
previous one. This was preventing to recover from error on my system
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit b91ecb00 ("gigaset: include cleanup cleanup") removed an implicit
sched.h inclusion that came in via slab.h, and caused various compile
problems as a result.
This should fix it.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a loop to wait for the controller to finish a locally-initiated CSR
lock operation. Google shows some occurrences of the "swap not done
yet" message which might indicate that some OHCI controllers are not
fast enough to do the lock/swap in the time needed for one PCI access.
This also correctly handles the case where the lock operation did not
finish, instead of silently returning an uninitialized value.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We must compute the offset from the CSR register base with the
full 48 address bits to prevent matching with addresses whose
lower 32 bits happen to be equal with one of the specially
handled registers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Returning -EIO for all errors would not allow clients to determine if
the resource allocation process itself failed, or if the resources are
not available. (The latter information is needed by CMP to synchronize
restoring of overlayed connections after a bus reset.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If there is a permanent error condition when communicating with the IRM,
after the sixth error, the retry variable will be decremented to -1.
If, in this case, the bits in channels_mask are not yet exhausted, the
next channel is retried 2^32 times.
To fix this, check that retry is never decremented beyond zero.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
gigaset: include cleanup cleanup
packet : remove init_net restriction
WAN: flush tx_queue in hdlc_ppp to prevent panic on rmmod hw_driver.
ip: Fix ip_dev_loopback_xmit()
net: dev_pick_tx() fix
fib: suppress lockdep-RCU false positive in FIB trie.
tun: orphan an skb on tx
forcedeth: fix tx limit2 flag check
iwlwifi: work around bogus active chains detection
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
In the original code we used -ENODEV as the number of bytes to
copy_to_user() and we didn't release the locks.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch fixes a memory leak by freeing priv in mc13783_regulator_remove
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current code is definitely crap: Largest pitch allowed spills into
the TILING_Y bit of the fence registers ... :(
I've rewritten the limits check under the assumption that 3rd gen hw
has a 3d pitch limit of 8kb (like 2nd gen). This is supported by an
otherwise totally misleading XXX comment.
This bug mostly resulted in tiling-corrupted pixmaps because the kernel
allowed too wide buffers to be tiled. Bug brought to the light by the
xf86-video-intel 2.11 release because that unconditionally enabled
tiling for pixmaps, relying on the kernel to check things. Tiling for
the framebuffer was not affected because the ddx does some additional
checks there ensure the buffer is within hw-limits.
v2: Instead of computing the value that would be written into the
hw fence registers and then checking the limits simply check whether
the stride is above the 8kb limit. To better document the hw, add
some WARN_ONs in i915_write_fence_reg like I've done for the i830
case (using the right limits).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=27449
Tested-by: Alexander Lam <lambchop468@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
we used to set the DIDL in the output device detected order.
But some BIOSes requires it to be initialized in the ACPI device order.
e.g. the value of the first field in DIDL stands for the first
ACPI video output device in ACPI namespace.
Now we initialize the DIDL using the device id, i.e. _ADR return value,
of each ACPI video device, if it is not 0.
https://bugzilla.kernel.org/show_bug.cgi?id=15054
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
IS_MOBILE() catches 85x, so we'd always try to use the 9xx FIFO sizing;
since there's an explicit 85x version, this seems wrong.
v2: Handle 830m correctly too.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 5a0e3ad causes slab.h to be included twice in many of the
Gigaset driver's source files, first via the common include file
gigaset.h and then a second time directly. Drop the spares, and
use the opportunity to clean up a few more similar cases.
Impact: cleanup, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
Use local_irq_restore in this error-handling case just like in the one just
below.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* local_irq_save (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many PCMCIA GPRS modems like: Onda Edge N100E, Novaway PC98 (OEM SPC98Z),
Rovermate Edgus Adaptmate-039 and others have same construction and
identification:
lspcmcia -vvv
Product Name: Generic Modem: MD55x 1.00 Serial number: xxxxx-xxx
Identification: manf_id: 0x015d card_id: 0x4c45
function: 2 (serial)
prod_id(1): "Generic" (0xc49e4731)
prod_id(2): "Modem: MD55x" (0x8913b110)
prod_id(3): "1.00" (0x83dbf271)
prod_id(4): "Serial number: xxxxx-xxx" (0x73ee9514)
Serial connection to GSM module based on Elan VPU16551 PCMCIA UART with
datasheet recommeded 14.7456MHz crystal oscillator.
By default serial_cs set UART clock == 1843200 Hz
For correct work need set clock 14745600 Hz.
This quirk already present in driver, only need add device in quirk list.
Signed-off-by: Timur Maximov <xcom.org@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pccard_validate_cis() nowadays destroys the CIS cache. Therefore,
calling it after card setup should be avoided. We can't control
the deprecated PCMCIA ioctl (which is only used on ARM nowadays),
but we can avoid -- and report -- any other calls.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
tx_queue is used as a temporary queue when not allowed to queue skb
directly to the hw device driver (which may sleep). Most paths flush
it before returning, but ppp_start() currently cannot. Make sure we
don't leave skbs pointing to a non-existent device.
Thanks to Michael Barkowski for reporting this problem.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.
Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.
For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63. However the mask generation was
not changed, so the mask was coming out as 0. This patch fixes it.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - switch mode upon system resume
Revert "Input: wacom - merge out and in prox events"
Input: matrix_keypad - allow platform to disable key autorepeat
Input: ALPS - add signature for HP Pavilion dm3 laptops
Input: i8042 - spelling fix
Input: sparse-keymap - implement safer freeing of the keymap
Input: update the status of the Multitouch X driver project
Input: clarify the no-finger event in multitouch protocol
Input: bcm5974 - retract efi-broken suspend_resume
Input: sparse-keymap - free the right keymap on error
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Reported-and-tested-by: Anton Anikin <Anton@Anikin.name>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Size needs to be calculated after manipulating with the start value.
Reported-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add the iMac9,1 and the MacBookPro2,2 temperature sensors to hwmon
driver applesmc to fix kernel bug #14429:
https://bugzilla.kernel.org/show_bug.cgi?id=14429
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When any temperature sensor type is changed, the corresponding
temperature value needs to be updated. The register caching mechanism
may delay this update, so we want to invalidate the cache to force an
immediate update.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently, if someone tries to set the thermal sensor type to an
unsupported value, subsequent accesses to the chip may temporarily
show the sensor in question as disabled. Use a temporary variable
and only update the cached value on success, to prevent such
confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Temperature channels can be used in 2 different modes (thermistor and
thermal diode) and we don't know which one, if any, is correct for
every given board. So don't arbitrarily choose one. Instead, leave the
temperature channels untouched. They can be configured from user-space
if needed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When CONFIG_REGULATOR isn't set, regulator_get_voltage() returns 0.
Properly handle this case by not trusting the value.
Reported-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I discovered two issues.
First the previous sht15_calc_temp() loop did not iterate through the
temppoints array since the (data->supply_uV > temppoints[i - 1].vdd)
test is always true in this direction.
Also the two-points linear interpolation function was returning biased
values due to a stray division by 1000 which shouldn't be there.
[JD: Also change the default value for d1 from 0 to something saner.]
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
This is a partial revert of 4cd8b5e2a1 "lguest: use KVM hypercalls";
we revert to using (just as questionable but more reliable) int $15 for
hypercalls. I didn't revert the register mapping, so we still use the
same calling convention as kvm.
KVM in more recent incarnations stopped injecting a fault when a guest
tried to use the VMCALL instruction from ring 1, so lguest under kvm
fails to make hypercalls. It was nice to share code with our KVM
cousins, but this was overreach.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Matias Zabaljauregui <zabaljauregui@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
It's only used by cmpxchg8b_emu (see db677ffa5f for the gory
details), and fixing that to be paravirt aware would be more work than
simply ignoring it (and AFAICT only help lguest). This makes lguest
work on machines which have cmpxchg8b, for kernels compiled for older
processors.
(We can't emulate it properly: the popf which expects to restore interrupts
does not trap).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: virtualization@lists.osdl.org
The following situation was observed in the field:
tap1 sends packets, tap2 does not consume them, as a result
tap1 can not be closed. This happens because
tun/tap devices can hang on to skbs undefinitely.
As noted by Herbert, possible solutions include a timeout followed by a
copy/change of ownership of the skb, or always copying/changing
ownership if we're going into a hostile device.
This patch implements the second approach.
Note: one issue still remaining is that since skbs
keep reference to tun socket and tun socket has a
reference to tun device, we won't flush backlog,
instead simply waiting for all skbs to get transmitted.
At least this is not user-triggerable, and
this was not reported in practice, my assumption is
other devices besides tap complete an skb
within finite time after it has been queued.
A possible solution for the second issue
would not to have socket reference the device,
instead, implement dev->destructor for tun, and
wait for all skbs to complete there, but this
needs some thought, probably too risky for 2.6.34.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Yan Vugenfirer <yvugenfi@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for bug 572201 @ bugs.debian.org
This patch fixes the TX_LIMIT feature flag. The previous logic check
for TX_LIMIT2 also took into account a device that only had TX_LIMIT
set.
Reported-by: Stephen Mulcahu <stephen.mulcahy@deri.org>
Reported-by: Ben Huchings <ben@decadent.org.uk>
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (25 commits)
smc91c92_cs: define multicast_table as unsigned char
can: avoids a false warning
e1000e: stop cleaning when we reach tx_ring->next_to_use
igb: restrict WoL for 82576 ET2 Quad Port Server Adapter
virtio_net: missing sg_init_table
Revert "tcp: Set CHECKSUM_UNNECESSARY in tcp_init_nondata_skb"
iwlwifi: need check for valid qos packet before free
tcp: Set CHECKSUM_UNNECESSARY in tcp_init_nondata_skb
udp: fix for unicast RX path optimization
myri10ge: fix rx_pause in myri10ge_set_pauseparam
net: corrected documentation for hardware time stamping
stmmac: use resource_size()
x.25 attempts to negotiate invalid throughput
x25: Patch to fix bug 15678 - x25 accesses fields beyond end of packet.
bridge: Fix IGMP3 report parsing
cnic: Fix crash during bnx2x MTU change.
qlcnic: fix set mac addr
r6040: fix r6040_multicast_list
vhost-net: fix vq_memory_access_ok error checking
ath9k: fix double calls to ath_radio_enable
...
smc91c92_cs:
* define multicast_table as unsigned char
* remove unnecessary "#ifndef final_version"
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx ring buffers after tx_ring->next_to_use are volatile and could
change, possibly causing a crash. Stop cleaning when we hit
tx_ring->next_to_use.
Signed-off-by: Terry Loftin <terry.loftin@hp.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict Wake-on-LAN to first port on 82576 ET2 quad port NICs, as it is
only supported there.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing sg_init_table for sg_set_buf in virtio_net which
induced in defer skb patch.
Reported-by: Thomas Müller <thomas@mathtm.de>
Tested-by: Thomas Müller <thomas@mathtm.de>
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-tip testing found:
eeepc-wmi.c:(.text+0x36673c): undefined reference to `sparse_keymap_report_event'
drivers/built-in.o: In function `eeepc_wmi_init':
eeepc-wmi.c:(.init.text+0x19cd0): undefined reference to `sparse_keymap_setup'
eeepc-wmi.c:(.init.text+0x19cf0): undefined reference to `sparse_keymap_free'
eeepc-wmi.c:(.init.text+0x19d0b): undefined reference to `sparse_keymap_free'
drivers/built-in.o: In function `eeepc_wmi_exit':
eeepc-wmi.c:(.exit.text+0x2e87): undefined reference to `sparse_keymap_free'
To fix this select INPUT_SPARSEKMAP, like the ASUS driver does.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We were storing -1 as an unsigned int and as a result the effect of
passing -1 was the same as using 1.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Corentin Chary <corentincj@iksaif.net>
The output of wmi_get_event_data shall be freed before return.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Yong Wang <yong.y.wang@linux.intel.com>
Add backlight support for WMI based Eee PC laptops.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Corentin Chary <corentincj@iksaif.net>
Add a platform device and use it as the parent device of all sub-devices.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Corentin Chary <corentincj@iksaif.net>
Add an eeepc_wmi context structure to manage all the sub-devices
that will be implemented later on. Put input device into it first.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Reviewed-by: Corentin Chary <corentincj@iksaif.net>
The SSB PCIcore code reused the IO resource fixup code from the original
2.4.x Broadcom patch for BCM47xx based devices, which was a quick hack
for doing PCI IO resource configuration back then (the boot loader
doesn't configure PCI devices on this platform).
However, this code is no longer necessary since the kernel now can do
PCI resource management fine all by itself, so remove the old code.
When removing the code, it becomes obvious that the mem_offset setting
in the PCIcore driver was wrong, however this was masked by the fixup
code before, except in a few cases involving yenta_socket. For BCM47xx,
the correct offset is 0, and since this is the only device using PCIcore
in host mode, the offset can simply be removed unconditionally.
Signed-off-by: Andreas Ferber <af@chaos-agency.de>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Markus Wigge <markus@cultcom.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On X startup we were getting a flicker where there shouldn't have been one.
the X DDX calls the kernel to set the properties to the same values (yes
it could be smarter), however the kernel was doing a pointless modeset then,
making my nice smooth boot ugly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
bnx2i driver has to wait and cleanup all iscsi endpoints before
returning from bnx2i_stop(). This is to make sure all chip resources
are freed before chip is reset.
As the requirements for 1G and 10G chipsets is different, added
per-device 'hba_shutdown_tmo' parameter to adapter structure
If the connections are not torn down by the daemon within this timeout
period, 'cid's will be leaked in 10G device. 1G devices are more
flexible and do not leak any resources because the whole chip ports
gets reset when MTU is changed or ethtool selftest is run
fixed a minor issue in bnx2i_ep_poll() which unnecessarily forced
error return code when driver timed out waiting for TCP connect
request to complete
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ibmvscsi uses dma_unmap_single() for buffers mapped via
dma_map_sg(). It works however it's the API violation. The DMA debug
facility complains about it:
http://marc.info/?l=linux-scsi&m=127018555013151&w=2
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This was introduced back in 2005 at the very start of the git era by:
df0ae2497d
[SCSI] allow sleeping in ->eh_host_reset_handler()
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a FSF request is returned with an error it should be reported
through blktrace for the ziomon tools, but the latency information
should not be read. Fix this by also calling zfcp_fsf_req_trace for
the error case, but skip reading the latencies inside the function.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When I made this patch:
b64e77f70b
it was to solve a problem where we were already on the waitqueue
becuase a connection problem/logout caused us to be on there
when we were cleaning up the session. If we happen to get
on queue for more normal reasons like their just does not happen
to be any send space at the same time we are closing the connection
we hit a race and get stuck in the wait.
We should not check if the waitqueue is active
because we could race with the network code. If
the network xmit code is just about to enter the
prepare to wait when we check for the waitqueue to
be active then we will miss each other and the
network code will fall into the wait and we will
not run wake_up.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If there are changes to the number of socket devices, we need to
start over in all cases: else pcmcia_request_configuration() might
get confused.
Reported-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Similar to commit 7a96e87d, we need to be aware of any parent PCI
device when requesting IO regions, even only for testing
("probing").
Reported-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use a previously assigned IRQ for all card functions, not only if
CONFIG_PCMCIA_PROBE is set.
Reported-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A userspace client got to see uninitialized stack-allocated memory if it
specified an _IOC_READ type of ioctl and an argument size larger than
expected by firewire-core's ioctl handlers (but not larger than the
core's union ioctl_arg).
Fix this by clearing the requested buffer size to zero, but only at _IOR
ioctls. This way, there is almost no runtime penalty to legitimate
ioctls. The only legitimate _IOR is FW_CDEV_IOC_GET_CYCLE_TIMER with 12
or 16 bytes to memset.
[Another way to fix this would be strict checking of argument size (and
possibly direction) vs. command number. However, we then need a lookup
table, and we need to allow for slight size deviations in case of 32bit
userland on 64bit kernel.]
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The definition of struct fw_cdev_iso_packet seems to imply that the
header_length must be quadlet-aligned, and in fact, specifying an
unaligned header has never really worked when using multiple packet
structures, because the position of the next control word is computed by
rounding the header_length _down_, so the last one to three bytes of the
header would overlap the next control word.
To avoid this problem, check that the header length is properly aligned.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In receive contexts, reject packets with header_length==0. This would
be an instruction to queue zero packets which would not make sense.
This prevents a division by zero in the OHCI driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This trys to shut up complains about invalid LVDS EDID during
mode probe, but uses fixed panel mode directly for panels with
broken EDID.
https://bugs.freedesktop.org/show_bug.cgi?id=23099https://bugs.freedesktop.org/show_bug.cgi?id=26395
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
shr/shl ops need the full dst rather than the pre-masked
version. Fixes fdo bug 27478 and kernel bug 15738.
v2: remove some unsed vars, add comments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check correct variable for allocation failure
RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
RDMA/cm: Set num_paths when manually assigning path records
IB/cm: Fix device_create() return value check
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (34 commits)
cfq-iosched: Fix the incorrect timeslice accounting with forced_dispatch
loop: Update mtime when writing using aops
block: expose the statistics in blkio.time and blkio.sectors for the root cgroup
backing-dev: Handle class_create() failure
Block: Fix block/elevator.c elevator_get() off-by-one error
drbd: lc_element_by_index() never returns NULL
cciss: unlock on error path
cfq-iosched: Do not merge queues of BE and IDLE classes
cfq-iosched: Add additional blktrace log messages in CFQ for easier debugging
i2o: Remove the dangerous kobj_to_i2o_device macro
block: remove 16 bytes of padding from struct request on 64bits
cfq-iosched: fix a kbuild regression
block: make CONFIG_BLK_CGROUP visible
Remove GENHD_FL_DRIVERFS
block: Export max number of segments and max segment size in sysfs
block: Finalize conversion of block limits functions
block: Fix overrun in lcm() and move it to lib
vfs: improve writeback_inodes_wb()
paride: fix off-by-one test
drbd: fix al-to-on-disk-bitmap for 4k logical_block_size
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (29 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.
The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.
This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This reverts commit ba168fc37d.
It changes user-visible sysfs interfaces, and breaks some existing user
space applications which apparently rely on the fact that the output
does not contain the "0x" prefix.
Requested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"len" hasn't been properly range checked so we shouldn't use it as an
array offset. This can only be written to by root but it would still be
annoying to accidentally write more than 3 characters and corrupt your
memory.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next: (21 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
Fixes garbled 3D on an nv46 card.
Reported-by: Francesco Marella <francesco.marella@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allows *some* DP cards to keep working in some corner cases that most
people shouldn't hit. I hit it all the time with development, so this
can stay for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This value interacts with some registers we don't currently know how to
program properly ourselves. The default of 5 that we were using matches
what the VBIOS on early DP cards do, but later ones use 6, which would
cause nouveau to program an incorrect mode on these chips.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
All indications seem to be that the version 0x30 table should be handled
the same way as 0x40 (as used on G80), at least for the parts that we
currently try use.
This commit cleans up the parsing to make it clearer about what we're
actually trying to achieve, and unifies the 0x30/0x40 parsing.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As opposed to repeatedly reading the amount back from the GPU every
time we need to know the VRAM size.
We should now fail to load gracefully on detecting no VRAM, rather than
something potentially messy happening.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously we were filling it the same as "placements", but in some
cases there're valid alternatives that we were ignoring completely.
Keeping a back-up memory type helps on several low-mem situations.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes the !vbo_fifo path in the 3D driver on certain chipsets. Still not
really any good idea of what exactly the magic achieves, but it makes
things work.
While we're at it, in the PCIEGART path, flush on unbinding also.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Stanse found that one error path in qla24xx_bsg_timeout omits to
unlock ha->hardware_lock. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found that two error paths in lpfc_bsg_rport_els_cmp and
lpfc_issue_ct_rsp_cmp omits to unlock phba->ct_ev_lock. It is
because they wrongly unlock phba->hbalock instead. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found that one error path in mgmt_invalidate_icds omits to unlock
ctrl->mbox_lock. Fix that.
Added in 756d29c8c7 (Enable async mode for mcc rings)
where the spinlock was moved.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
adpt_i2o_delete_hba() calls kfree() so we have to save "pHba->next"
before calling it. Also inside adpt_i2o_delete_hba() itself, there
was another use after free bug which I fixed by moving the kfree()
down a line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update mtime when writing to backing filesystem using the address space
operations write_begin and write_end.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
While testing completion timeouts I found that hardware was not recovering.
It looks like the hot reset was never being propagated to the endpoint
devices on the bus due to the fact that we were clearing the bit too
quickly.
The documentation I have states that we should be transmitting hot reset
TS1s for 2ms. To achieve this I have added a 2ms delay from the time we
set the secondary bus reset bit to the time we clear it. In addition I
changed the define used for the secondary bus reset bit to match the
register define that was being used.
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
