When running a Fedora 15 (x86) on an x86_64 kernel, in the boot process
plymouthd complains about those two missing ioctls:
[ 2.581783] ioctl32(plymouthd:186): Unknown cmd fd(10) cmd(00005457){t:'T';sz:0} arg(ffb6a5d0) on /dev/tty1
[ 2.581803] ioctl32(plymouthd:186): Unknown cmd fd(10) cmd(00005456){t:'T';sz:0} arg(ffb6a680) on /dev/tty1
both ioctl functions work on the 'struct termios' resp. 'struct termios2',
which has the same size (36 bytes resp. 44 bytes) on x86 and x86_64,
so it's just a matter of converting the pointer from userland.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To support >32-bit physical addresses for UIO_MEM_PHYS type we need to
extend the width of 'addr' in struct uio_mem. Numerous platforms like
embedded PPC, ARM, and X86 have support for systems with larger physical
address than logical.
Since 'addr' may contain a physical, logical, or virtual address the
easiest solution is to just change the type to 'phys_addr_t' which
should always be greater than or equal to the sizeof(void *) such that
it can properly hold any of the address types.
For physical address we can support up to a 44-bit physical address on a
typical 32-bit system as we utilize remap_pfn_range() for the mapping of
the memory region and pfn's are represnted by shifting the address by
the page size (typically 4k).
Signed-off-by: Kai Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
rpc_sockaddr2uaddr is only used by net/sunrpc/rpcb_clnt.c, where
it is used in a non-blockable context in at least one case.
Add non-blocking capability by adding a gfp_t argument
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The same function is used by idmap, gss and blocklayout code. Make it
generic.
Signed-off-by: Peng Tao <peng_tao@emc.com>
Signed-off-by: Jim Rees <rees@umich.edu>
Cc: stable@kernel.org [3.0]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The BerliOS project, which currently hosts our mailinglist, will
close with the end of the year. Now take the chance and remove all
occurrences of the mailinglist address from the source files.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a mechanism to resume selected IRQs during syscore_resume
instead of dpm_resume_noirq.
Under Xen we need to resume IRQs associated with IPIs early enough
that the resched IPI is unmasked and we can therefore schedule
ourselves out of the stop_machine where the suspend/resume takes
place.
This issue was introduced by 676dc3cf5b "xen: Use IRQF_FORCE_RESUME".
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1318713254.11016.52.camel@dagon.hellion.org.uk
Cc: stable@kernel.org (at least to 2.6.32.y)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is a problem with the current ordering of hibernate code which
leads to deadlocks in some filesystems' memory shrinkers. Namely,
some filesystems use freezable kernel threads that are inactive when
the hibernate memory preallocation is carried out. Those same
filesystems use memory shrinkers that may be triggered by the
hibernate memory preallocation. If those memory shrinkers wait for
the frozen kernel threads, the hibernate process deadlocks (this
happens with XFS, for one example).
Apparently, it is not technically viable to redesign the filesystems
in question to avoid the situation described above, so the only
possible solution of this issue is to defer the freezing of kernel
threads until the hibernate memory preallocation is done, which is
implemented by this change.
Unfortunately, this requires the memory preallocation to be done
before the "prepare" stage of device freeze, so after this change the
only way drivers can allocate additional memory for their freeze
routines in a clean way is to use PM notifiers.
Reported-by: Christoph <cr2005@u-club.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce the config option CONFIG_VT_CONSOLE_SLEEP in order to cleanup
the #if defined ugliness for the vt suspend support functions. Note that
CONFIG_VT_CONSOLE is already dependant on CONFIG_VT.
The function pm_set_vt_switch is actually dependant on CONFIG_VT and not
CONFIG_PM_SLEEP. This fixes a compile error when CONFIG_PM_SLEEP is
not set:
drivers/tty/vt/vt_ioctl.c:1794: error: redefinition of 'pm_set_vt_switch'
include/linux/suspend.h:17: error: previous definition of 'pm_set_vt_switch' was here
Also, remove the incorrect path from the comment in console.c.
[rjw: Replaced #if defined() with #ifdef in suspend.h.]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
For s390 there is one additional byte associated with each page,
the storage key. This byte contains the referenced and changed
bits and needs to be included into the hibernation image.
If the storage keys are not restored to their previous state all
original pages would appear to be dirty. This can cause
inconsistencies e.g. with read-only filesystems.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Record S3 failure time about each reason and the latest two failed
devices' names in S3 progress.
We can check it through 'suspend_stats' entry in debugfs.
The motivation of the patch:
We are enabling power features on Medfield. Comparing with PC/notebook,
a mobile enters/exits suspend-2-ram (we call it s3 on Medfield) far
more frequently. If it can't enter suspend-2-ram in time, the power
might be used up soon.
We often find sometimes, a device suspend fails. Then, system retries
s3 over and over again. As display is off, testers and developers
don't know what happens.
Some testers and developers complain they don't know if system
tries suspend-2-ram, and what device fails to suspend. They need
such info for a quick check. The patch adds suspend_stats under
debugfs for users to check suspend to RAM statistics quickly.
If not using this patch, we have other methods to get info about
what device fails. One is to turn on CONFIG_PM_DEBUG, but users
would get too much info and testers need recompile the system.
In addition, dynamic debug is another good tool to dump debug info.
But it still doesn't match our utilization scenario closely.
1) user need write a user space parser to process the syslog output;
2) Our testing scenario is we leave the mobile for at least hours.
Then, check its status. No serial console available during the
testing. One is because console would be suspended, and the other
is serial console connecting with spi or HSU devices would consume
power. These devices are powered off at suspend-2-ram.
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add configuration setting for drivers to turn spoof checking on or off
for discrete VFs.
v2 - Fix indentation problem, wrap the ifla_vf_info structure in
#ifdef __KERNEL__ to prevent user space from accessing and
change function paramater for the spoof check setting netdev
op from u8 to bool.
v3 - Preset spoof check setting to -1 so that user space tools such
as ip can detect that the driver didn't report a spoofcheck
setting. Prevents incorrect display of spoof check settings
for drivers that don't report it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb truesize currently accounts for sk_buff struct and part of skb head.
kmalloc() roundings are also ignored.
Considering that skb_shared_info is larger than sk_buff, its time to
take it into account for better memory accounting.
This patch introduces SKB_TRUESIZE(X) macro to centralize various
assumptions into a single place.
At skb alloc phase, we put skb_shared_info struct at the exact end of
skb head, to allow a better use of memory (lowering number of
reallocations), since kmalloc() gives us power-of-two memory blocks.
Unless SLUB/SLUB debug is active, both skb->head and skb_shared_info are
aligned to cache lines, as before.
Note: This patch might trigger performance regressions because of
misconfigured protocol stacks, hitting per socket or global memory
limits that were previously not reached. But its a necessary step for a
more accurate memory accounting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch do the following things:
1. Add header and Copyright for marvell usb driver.
2. Add mv_usb.h in include/linux/platform_data, make the driver
fits all the marvell platform using the same ChipIdea usb ip.
3. Some SOC may has mutiple clock sources, so let me define it
in mv_usb_platform_data and give two helper functions named
udc_clock_enable/udc_clock_disable to deal with the clocks.
4. Different SOCs will have some difference in PHY initialization,
so we will remove file mv_udc_phy.c and add two funtions in
mv_usb_platform_data, let the platform relative driver to realize it.
5. Rewrite probe function according to the modification list above. Find
it will kernel panic when probe failed. The root cause is as follows:
When probe failed, the error handle may call device_unregister()
which in return will call gadget_release.In current code,
gadget_release have two issues:
1: the_controller is a NULL pointer.
2: if we free udc here, then the following code in probe
will access NULL pointer.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch add DVSTCTR control function for HOST support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs will have register DVSTCTR control function for HOST support.
This patch changes usbhsc_bus_ctrl() to usbsc_set_buswait(),
to remove DVSTCTR access from it,
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SH7757 has a USB function with internal DMA controller (SUDMAC).
This patch supports the SUDMAC. The SUDMAC is incompatible with
general-purpose DMAC. So, it doesn't use dmaengine.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This creates a subsystem for handling of pin control devices.
These are devices that control different aspects of package
pins.
Currently it handles pinmuxing, i.e. assigning electronic
functions to groups of pins on primarily PGA and BGA type of
chip packages which are common in embedded systems.
The plan is to also handle other I/O pin control aspects
such as biasing, driving, input properties such as
schmitt-triggering, load capacitance etc within this
subsystem, to remove a lot of ARM arch code as well as
feature-creepy GPIO drivers which are implementing the same
thing over and over again.
This is being done to depopulate the arch/arm/* directory
of such custom drivers and try to abstract the infrastructure
they all need. See the Documentation/pinctrl.txt file that is
part of this patch for more details.
ChangeLog v1->v2:
- Various minor fixes from Joe's and Stephens review comments
- Added a pinmux_config() that can invoke custom configuration
with arbitrary data passed in or out to/from the pinmux driver
ChangeLog v2->v3:
- Renamed subsystem folder to "pinctrl" since we will likely
want to keep other pin control such as biasing in this
subsystem too, so let us keep to something generic even though
we're mainly doing pinmux now.
- As a consequence, register pins as an abstract entity separate
from the pinmux. The muxing functions will claim pins out of the
pin pool and make sure they do not collide. Pins can now be
named by the pinctrl core.
- Converted the pin lookup from a static array into a radix tree,
I agreed with Grant Likely to try to avoid any static allocation
(which is crap for device tree stuff) so I just rewrote this
to be dynamic, just like irq number descriptors. The
platform-wide definition of number of pins goes away - this is
now just the sum total of the pins registered to the subsystem.
- Make sure mappings with only a function name and no device
works properly.
ChangeLog v3->v4:
- Define a number space per controller instead of globally,
Stephen and Grant requested the same thing so now maps need to
define target controller, and the radix tree of pin descriptors
is a property on each pin controller device.
- Add a compulsory pinctrl device entry to the pinctrl mapping
table. This must match the pinctrl device, like "pinctrl.0"
- Split the file core.c in two: core.c and pinmux.c where the
latter carry all pinmux stuff, the core is for generic pin
control, and use local headers to access functionality between
files. It is now possible to implement a "blank" pin controller
without pinmux capabilities. This split will make new additions
like pindrive.c, pinbias.c etc possible for combined drivers
and chunks of functionality which is a GoodThing(TM).
- Rewrite the interaction with the GPIO subsystem - the pin
controller descriptor now handles this by defining an offset
into the GPIO numberspace for its handled pin range. This is
used to look up the apropriate pin controller for a GPIO pin.
Then that specific GPIO range is matched 1-1 for the target
controller instance.
- Fixed a number of review comments from Joe Perches.
- Broke out a header file pinctrl.h for the core pin handling
stuff that will be reused by other stuff than pinmux.
- Fixed some erroneous EXPORT() stuff.
- Remove mispatched U300 Kconfig and Makefile entries
- Fixed a number of review comments from Stephen Warren, not all
of them - still WIP. But I think the new mapping that will
specify which function goes to which pin mux controller address
50% of your concerns (else beat me up).
ChangeLog v4->v5:
- Defined a "position" for each function, so the pin controller now
tracks a function in a certain position, and the pinmux maps define
what position you want the function in. (Feedback from Stephen
Warren and Sascha Hauer).
- Since we now need to request a combined function+position from
the machine mapping table that connect mux settings to drivers,
it was extended with a position field and a name field. The
name field is now used if you e.g. need to switch between two
mux map settings at runtime.
- Switched from a class device to using struct bus_type for this
subsystem. Verified sysfs functionality: seems to work fine.
(Feedback from Arnd Bergmann and Greg Kroah-Hartman)
- Define a per pincontroller list of GPIO ranges from the GPIO
pin space that can be handled by the pin controller. These can
be added one by one at runtime. (Feedback from Barry Song)
- Expanded documentation of regulator_[get|enable|disable|put]
semantics.
- Fixed a number of review comments from Barry Song. (Thanks!)
ChangeLog v5->v6:
- Create an abstract pin group concept that can sort pins into
named and enumerated groups no matter what the use of these
groups may be, one possible usecase is a group of pins being
muxed in or so. The intention is however to also use these
groups for other pin control activities.
- Make it compulsory for pinmux functions to associate with
at least one group, so the abstract pin group concept is used
to define the groups of pins affected by a pinmux function.
The pinmux driver interface has been altered so as to enforce
a function to list applicable groups per function.
- Provide an optional .group entry in the pinmux machine map
so the map can select beteween different available groups
to be used with a certain function.
- Consequent changes all over the place so that e.g. debugfs
present reasonable information about the world.
- Drop the per-pin mux (*config) function in the pinmux_ops
struct - I was afraid that this would start to be used for
things totally unrelated to muxing, we can introduce that to
the generic struct pinctrl_ops if needed. I want to keep
muxing orthogonal to other pin control subjects and not mix
these things up.
ChangeLog v6->v7:
- Make it possible to have several map entries matching the
same device, pin controller and function, but using
a different group, and alter the semantics so that
pinmux_get() will pick all matching map entries, and
store the associated groups in a list. The list will
then be iterated over at pinmux_enable()/pinmux_disable()
and corresponding driver functions called for each
defined group. Notice that you're only allowed to map
multiple *groups* to the same
{ device, pin controller, function } triplet, attempts
to map the same device to multiple pin controllers will
for example fail. This is hopefully the crucial feature
requested by Stephen Warren.
- Add a pinmux hogging field to the pinmux mapping entries,
and enable the pinmux core to hog pinmux map entries.
This currently only works for pinmuxes without assigned
devices as it looks now, but with device trees we can
look up the corresponding struct device * entries when
we register the pinmux driver, and have it hog each
pinmux map in turn, for a simple approach to
non-dynamic pin muxing. This addresses an issue from
Grant Likely that the machine should take care of as
much of the pinmux setup as possible, not the devices.
By supplying a list of hogs, it can now instruct the
core to take care of any static mappings.
- Switch pinmux group retrieveal function to grab an
array of strings representing the groups rather than an
array of unsigned and rewrite accordingly.
- Alter debugfs to show the grouplist handled by each
pinmux. Also add a list of hogs.
- Dynamically allocate a struct pinmux at pinmux_get() and
free it at pinmux_put(), then add these to the global
list of pinmuxes active as we go along.
- Go over the list of pinmux maps at pinmux_get() time
and repeatedly apply matches.
- Retrieve applicable groups per function from the driver
as a string array rather than a unsigned array, then
lookup the enumerators.
- Make the device to pinmux map a singleton - only allow the
mapping table to be registered once and even tag the
registration function with __init so it surely won't be
abused.
- Create a separate debugfs file to view the pinmux map at
runtime.
- Introduce a spin lock to the pin descriptor struct, lock it
when modifying pin status entries. Reported by Stijn Devriendt.
- Fix up the documentation after review from Stephen Warren.
- Let the GPIO ranges give names as const char * instead of some
fixed-length string.
- add a function to unregister GPIO ranges to mirror the
registration function.
- Privatized the struct pinctrl_device and removed it from the
<linux/pinctrl/pinctrl.h> API, the drivers do not need to know
the members of this struct. It is now in the local header
"core.h".
- Rename the concept of "anonymous" mux maps to "system" muxes
and add convenience macros and documentation.
ChangeLog v7->v8:
- Delete the leftover pinmux_config() function from the
<linux/pinctrl/pinmux.h> header.
- Fix a race condition found by Stijn Devriendt in pin_request()
ChangeLog v8->v9:
- Drop the bus_type and the sysfs attributes and all, we're not on
the clear about how this should be used for e.g. userspace
interfaces so let us save this for the future.
- Use the right name in MAINTAINERS, PIN CONTROL rather than
PINMUX
- Don't kfree() the device state holder, let the .remove() callback
handle this.
- Fix up numerous kerneldoc headers to have one line for the function
description and more verbose documentation below the parameters
ChangeLog v9->v10:
- pinctrl: EXPORT_SYMBOL needs export.h, folded in a patch
from Steven Rothwell
- fix pinctrl_register error handling, folded in a patch from
Axel Lin
- Various fixes to documentation text so that it's consistent.
- Removed pointless comment from drivers/Kconfig
- Removed dependency on SYSFS since we removed the bus in
v9.
- Renamed hopelessly abbreviated pctldev_* functions to the
more verbose pinctrl_dev_*
- Drop mutex properly when looking up GPIO ranges
- Return NULL instead of ERR_PTR() errors on registration of
pin controllers, using cast pointers is fragile. We can
live without the detailed error codes for sure.
Cc: Stijn Devriendt <highguy@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch exposes the tos value for the TCP sockets when the TOS flag
is requested in the ext_flags for the inet_diag request. This would mainly be
used to expose TOS values for both for TCP and UDP sockets. Currently it is
supported for TCP. When netlink support for UDP would be added the support
to expose the TOS values would alse be done. For IPV4 tos value is exposed
and for IPV6 tclass value is exposed.
Signed-off-by: Murali Raja <muralira@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only used/needed by the vmbus core code, so move it out of the
hyperv.h file and into the .c file that uses it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function is only used in the file it is declared in
(channel_mgmt.c) so make it static and remove it from the hyperv.h file.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This file was created by mushing different .h files together and it
shows. This change removes some unneeded forward declarations.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have no idea what these were ever for, but they aren't used, so delete
them.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They aren't used anywhere anymore now that the debugging macros are
gone, so remove it from hyperv.h as well.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As there is no user of this variable, it's time to delete it. For
dynamic debugging of the hyperv code, use the standard dynamic debug
kernel interface.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These aren't used by anyone anymore, so remove them before someone tries
to use them again.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's a global symbol, so properly prefix it and use the proper EXPORT
value as well.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one outside of the hyperv core needs to include the asm/hyperv.h
file, so don't put it in the "global" include/linux/hyperv.h file.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After many years wandering the desert, it is finally time for the
Microsoft HyperV code to move out of the staging directory. Or at least
the core hyperv bus code, and the utility driver, the rest still have
some review to get through by the various subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
The Kirkwood gave an unaligned memory access error on
line 742 of drivers/usb/host/echi-hcd.c:
"ehci->last_periodic_enable = ktime_get_real();"
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* pm-domains:
PM / Domains: Split device PM domain data into base and need_restore
ARM: mach-shmobile: sh7372 sleep warning fixes
ARM: mach-shmobile: sh7372 A3SM support
ARM: mach-shmobile: sh7372 generic suspend/resume support
PM / Domains: Preliminary support for devices with power.irq_safe set
PM: Move clock-related definitions and headers to separate file
PM / Domains: Use power.sybsys_data to reduce overhead
PM: Reference counting of power.subsys_data
PM: Introduce struct pm_subsys_data
ARM / shmobile: Make A3RV be a subdomain of A4LC on SH7372
PM / Domains: Rename argument of pm_genpd_add_subdomain()
PM / Domains: Rename GPD_STATE_WAIT_PARENT to GPD_STATE_WAIT_MASTER
PM / Domains: Allow generic PM domains to have multiple masters
PM / Domains: Add "wait for parent" status for generic PM domains
PM / Domains: Make pm_genpd_poweron() always survive parent removal
PM / Domains: Do not take parent locks to modify subdomain counters
PM / Domains: Implement subdomain counters as atomic fields
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
The two new attributes exclude_guest and exclude_host can
bes used by user-space to tell the kernel to setup
performance counter to either only count while the CPU is in
guest or in host mode.
An additional check is also introduced to make sure
user-space does not try to exclude guest and host mode from
counting.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1317816084-18026-2-git-send-email-gleb@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To read the current PM QoS value for a given device we need to
make sure that the device's power.constraints object won't be
removed while we're doing that. For this reason, put the
operation under dev->power.lock and acquire the lock
around the initialization and removal of power.constraints.
Moreover, since we're using the value of power.constraints to
determine whether or not the object is present, the
power.constraints_state field isn't necessary any more and may be
removed. However, dev_pm_qos_add_request() needs to check if the
device is being removed from the system before allocating a new
PM QoS constraints object for it, so make it use the
power.power_state field of struct device for this purpose.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* git://github.com/davem330/net:
pch_gbe: Fixed the issue on which a network freezes
pch_gbe: Fixed the issue on which PC was frozen when link was downed.
make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
net: xen-netback: correctly restart Tx after a VM restore/migrate
bonding: properly stop queuing work when requested
can bcm: fix incomplete tx_setup fix
RDSRDMA: Fix cleanup of rds_iw_mr_pool
net: Documentation: Fix type of variables
ibmveth: Fix oops on request_irq failure
ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
cxgb4: Fix EEH on IBM P7IOC
can bcm: fix tx_setup off-by-one errors
MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
dp83640: reduce driver noise
ptp: fix L2 event message recognition
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults. Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.
Also, add the option for peer to peer DMA MPS configuration. Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another. To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a gpio setup function which gives a chance to set up
platform specific configuration such as pin multiplexing,
input/output direction at the runtime or booting time.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This repairs problem with compile library in userspace (libnl).
Signed-off-by: Jiří Župka <jzupka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows ss command (iproute2) to display "ecnseen" if at least one packet
with ECT(0) or ECT(1) or ECN was received by this socket.
"ecn" means ECN was negotiated at session establishment (TCP level)
"ecnseen" means we received at least one packet with ECT fields set (IP
level)
ss -i
...
ESTAB 0 0 192.168.20.110:22 192.168.20.144:38016
ino:5950 sk:f178e400
mem:(r0,w0,f0,t0) ts sack ecn ecnseen bic wscale:7,8 rto:210
rtt:12.5/7.5 cwnd:10 send 9.3Mbps rcv_space:14480
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As request_percpu_irq() doesn't allow for a percpu interrupt to have
its type configured (it is generally impossible to configure it on all
CPUs at once), add a 'type' argument to enable_percpu_irq().
This allows some low-level, board specific init code to be switched to
a generic API.
[ tglx: Added WARN_ON argument ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ARM GIC interrupt controller offers per CPU interrupts (PPIs),
which are usually used to connect local timers to each core. Each CPU
has its own private interface to the GIC, and only sees the PPIs that
are directly connect to it.
While these timers are separate devices and have a separate interrupt
line to a core, they all use the same IRQ number.
For these devices, request_irq() is not the right API as it assumes
that an IRQ number is visible by a number of CPUs (through the
affinity setting), but makes it very awkward to express that an IRQ
number can be handled by all CPUs, and yet be a different interrupt
line on each CPU, requiring a different dev_id cookie to be passed
back to the handler.
The *_percpu_irq() functions is designed to overcome these
limitations, by providing a per-cpu dev_id vector:
int request_percpu_irq(unsigned int irq, irq_handler_t handler,
const char *devname, void __percpu *percpu_dev_id);
void free_percpu_irq(unsigned int, void __percpu *);
int setup_percpu_irq(unsigned int irq, struct irqaction *new);
void remove_percpu_irq(unsigned int irq, struct irqaction *act);
void enable_percpu_irq(unsigned int irq);
void disable_percpu_irq(unsigned int irq);
The API has a number of limitations:
- no interrupt sharing
- no threading
- common handler across all the CPUs
Once the interrupt is requested using setup_percpu_irq() or
request_percpu_irq(), it must be enabled by each core that wishes its
local interrupt to be delivered.
Based on an initial patch by Thomas Gleixner.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Four cpufreq-like governors are provided as examples.
powersave: use the lowest frequency possible. The user (device) should
set the polling_ms as 0 because polling is useless for this governor.
performance: use the highest freqeuncy possible. The user (device)
should set the polling_ms as 0 because polling is useless for this
governor.
userspace: use the user specified frequency stored at
devfreq.user_set_freq. With sysfs support in the following patch, a user
may set the value with the sysfs interface.
simple_ondemand: simplified version of cpufreq's ondemand governor.
When a user updates OPP entries (enable/disable/add), OPP framework
automatically notifies devfreq to update operating frequency
accordingly. Thus, devfreq users (device drivers) do not need to update
devfreq manually with OPP entry updates or set polling_ms for powersave
, performance, userspace, or any other "static" governors.
Note that these are given only as basic examples for governors and any
devices with devfreq may implement their own governors with the drivers
and use them.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
With OPPs, a device may have multiple operable frequency and voltage
sets. However, there can be multiple possible operable sets and a system
will need to choose one from them. In order to reduce the power
consumption (by reducing frequency and voltage) without affecting the
performance too much, a Dynamic Voltage and Frequency Scaling (DVFS)
scheme may be used.
This patch introduces the DVFS capability to non-CPU devices with OPPs.
DVFS is a techique whereby the frequency and supplied voltage of a
device is adjusted on-the-fly. DVFS usually sets the frequency as low
as possible with given conditions (such as QoS assurance) and adjusts
voltage according to the chosen frequency in order to reduce power
consumption and heat dissipation.
The generic DVFS for devices, devfreq, may appear quite similar with
/drivers/cpufreq. However, cpufreq does not allow to have multiple
devices registered and is not suitable to have multiple heterogenous
devices with different (but simple) governors.
Normally, DVFS mechanism controls frequency based on the demand for
the device, and then, chooses voltage based on the chosen frequency.
devfreq also controls the frequency based on the governor's frequency
recommendation and let OPP pick up the pair of frequency and voltage
based on the recommended frequency. Then, the chosen OPP is passed to
device driver's "target" callback.
When PM QoS is going to be used with the devfreq device, the device
driver should enable OPPs that are appropriate with the current PM QoS
requests. In order to do so, the device driver may call opp_enable and
opp_disable at the notifier callback of PM QoS so that PM QoS's
update_target() call enables the appropriate OPPs. Note that at least
one of OPPs should be enabled at any time; be careful when there is a
transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'irq-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
irq: Fix check for already initialized irq_domain in irq_domain_add
irq: Add declaration of irq_domain_simple_ops to irqdomain.h
* 'x86-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86/rtc: Don't recursively acquire rtc_lock
* 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
posix-cpu-timers: Cure SMP wobbles
sched: Fix up wchan borkage
sched/rt: Migrate equal priority tasks to available CPUs
The patch enables to register notifier_block for an OPP-device in order
to get notified for any changes in the availability of OPPs of the
device. For example, if a new OPP is inserted or enable/disable status
of an OPP is changed, the notifier is executed.
This enables the usage of opp_add, opp_enable, and opp_disable to
directly take effect with any connected entities such as cpufreq or
devfreq.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register and implement the TDLS cfg80211 callback functions.
Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.
Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure we've got a function so users can enable/disable the
cache bypass option.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
David reported:
Attached below is a watered-down version of rt/tst-cpuclock2.c from
GLIBC. Just build it with "gcc -o test test.c -lpthread -lrt" or
similar.
Run it several times, and you will see cases where the main thread
will measure a process clock difference before and after the nanosleep
which is smaller than the cpu-burner thread's individual thread clock
difference. This doesn't make any sense since the cpu-burner thread
is part of the top-level process's thread group.
I've reproduced this on both x86-64 and sparc64 (using both 32-bit and
64-bit binaries).
For example:
[davem@boricha build-x86_64-linux]$ ./test
process: before(0.001221967) after(0.498624371) diff(497402404)
thread: before(0.000081692) after(0.498316431) diff(498234739)
self: before(0.001223521) after(0.001240219) diff(16698)
[davem@boricha build-x86_64-linux]$
The diff of 'process' should always be >= the diff of 'thread'.
I make sure to wrap the 'thread' clock measurements the most tightly
around the nanosleep() call, and that the 'process' clock measurements
are the outer-most ones.
---
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <fcntl.h>
#include <string.h>
#include <errno.h>
#include <pthread.h>
static pthread_barrier_t barrier;
static void *chew_cpu(void *arg)
{
pthread_barrier_wait(&barrier);
while (1)
__asm__ __volatile__("" : : : "memory");
return NULL;
}
int main(void)
{
clockid_t process_clock, my_thread_clock, th_clock;
struct timespec process_before, process_after;
struct timespec me_before, me_after;
struct timespec th_before, th_after;
struct timespec sleeptime;
unsigned long diff;
pthread_t th;
int err;
err = clock_getcpuclockid(0, &process_clock);
if (err)
return 1;
err = pthread_getcpuclockid(pthread_self(), &my_thread_clock);
if (err)
return 1;
pthread_barrier_init(&barrier, NULL, 2);
err = pthread_create(&th, NULL, chew_cpu, NULL);
if (err)
return 1;
err = pthread_getcpuclockid(th, &th_clock);
if (err)
return 1;
pthread_barrier_wait(&barrier);
err = clock_gettime(process_clock, &process_before);
if (err)
return 1;
err = clock_gettime(my_thread_clock, &me_before);
if (err)
return 1;
err = clock_gettime(th_clock, &th_before);
if (err)
return 1;
sleeptime.tv_sec = 0;
sleeptime.tv_nsec = 500000000;
nanosleep(&sleeptime, NULL);
err = clock_gettime(th_clock, &th_after);
if (err)
return 1;
err = clock_gettime(my_thread_clock, &me_after);
if (err)
return 1;
err = clock_gettime(process_clock, &process_after);
if (err)
return 1;
diff = process_after.tv_nsec - process_before.tv_nsec;
printf("process: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
process_before.tv_sec, process_before.tv_nsec,
process_after.tv_sec, process_after.tv_nsec, diff);
diff = th_after.tv_nsec - th_before.tv_nsec;
printf("thread: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
th_before.tv_sec, th_before.tv_nsec,
th_after.tv_sec, th_after.tv_nsec, diff);
diff = me_after.tv_nsec - me_before.tv_nsec;
printf("self: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
me_before.tv_sec, me_before.tv_nsec,
me_after.tv_sec, me_after.tv_nsec, diff);
return 0;
}
This is due to us using p->se.sum_exec_runtime in
thread_group_cputime() where we iterate the thread group and sum all
data. This does not take time since the last schedule operation (tick
or otherwise) into account. We can cure this by using
task_sched_runtime() at the cost of having to take locks.
This also means we can (and must) do away with
thread_group_sched_runtime() since the modified thread_group_cputime()
is now more accurate and would deadlock when called from
thread_group_sched_runtime().
Aside of that it makes the function safe on 32 bit systems. The old
code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a
64bit value and could be changed on another cpu at the same time.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twins
Tested-by: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add to the dev_state and alloc_async structures the user namespace
corresponding to the uid and euid. Pass these to kill_pid_info_as_uid(),
which can then implement a proper, user-namespace-aware uid check.
Changelog:
Sep 20: Per Oleg's suggestion: Instead of caching and passing user namespace,
uid, and euid each separately, pass a struct cred.
Sep 26: Address Alan Stern's comments: don't define a struct cred at
usbdev_open(), and take and put a cred at async_completed() to
ensure it lasts for the duration of kill_pid_info_as_cred().
Signed-off-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 7765be (Fix RCU_BOOST race handling current->rcu_read_unlock_special)
introduced a new ->rcu_boosted field in the task structure. This is
redundant because the existing ->rcu_boost_mutex will be non-NULL at
any time that ->rcu_boosted is nonzero. Therefore, this commit removes
->rcu_boosted and tests ->rcu_boost_mutex instead.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
We only need to constrain the compiler if we are actually exiting
the top-level RCU read-side critical section. This commit therefore
moves the first barrier() cal in __rcu_read_unlock() to inside the
"if" statement, thus avoiding needless register flushes for inner
rcu_read_unlock() calls.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The differences between rcu_assign_pointer() and RCU_INIT_POINTER() are
subtle, and it is easy to use the the cheaper RCU_INIT_POINTER() when
the more-expensive rcu_assign_pointer() should have been used instead.
The consequences of this mistake are quite severe.
This commit therefore carefully lays out the situations in which it it
permissible to use RCU_INIT_POINTER().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Recent changes to gcc give warning messages on rcu_assign_pointers()'s
checks that allow it to determine when it is OK to omit the memory
barrier. Stephen Hemminger tried a number of gcc tricks to silence
this warning, but #pragmas and CPP macros do not work together in the
way that would be required to make this work.
However, we now have RCU_INIT_POINTER(), which already omits this
memory barrier, and which therefore may be used when assigning NULL to
an RCU-protected pointer that is accessible to readers. This commit
therefore makes rcu_assign_pointer() unconditionally emit the memory
barrier.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
RCU no longer uses this global variable, nor does anyone else. This
commit therefore removes this variable. This reduces memory footprint
and also removes some atomic instructions and memory barriers from
the dyntick-idle path.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_dereference_bh_protected() and rcu_dereference_sched_protected()
macros are synonyms for rcu_dereference_protected() and are not used
anywhere in mainline. This commit therefore removes them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This patch #ifdefs TINY_RCU kthreads out of the kernel unless RCU_BOOST=y,
thus eliminating context-switch overhead if RCU priority boosting has
not been configured.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There was recently some controversy about the overhead of invoking RCU
callbacks. Add TRACE_EVENT()s to obtain fine-grained timings for the
start and stop of a batch of callbacks and also for each callback invoked.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull the code that waits for an RCU grace period into a single function,
which is then called by synchronize_rcu() and friends in the case of
TREE_RCU and TREE_PREEMPT_RCU, and from rcu_barrier() and friends in
the case of TINY_RCU and TINY_PREEMPT_RCU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Take a first step towards untangling Linux kernel header files by
placing the struct rcu_head definition into include/linux/types.h
and including include/linux/types.h in include/linux/rcupdate.h
where struct rcu_head used to be defined. The actual inclusion point
for include/linux/types.h is with the rest of the #include directives
rather than at the point where struct rcu_head used to be defined,
as suggested by Mathieu Desnoyers.
Once this is in place, then header files that need only rcu_head
can include types.h rather than rcupdate.h.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Long ago, using TREE_RCU with PREEMPT would result in "scheduling
while atomic" diagnostics if you blocked in an RCU read-side critical
section. However, PREEMPT now implies TREE_PREEMPT_RCU, which defeats
this diagnostic. This commit therefore adds a replacement diagnostic
based on PROVE_RCU.
Because rcu_lockdep_assert() and lockdep_rcu_dereference() are now being
used for things that have nothing to do with rcu_dereference(), rename
lockdep_rcu_dereference() to lockdep_rcu_suspicious() and add a third
argument that is a string indicating what is suspicious. This third
argument is passed in from a new third argument to rcu_lockdep_assert().
Update all calls to rcu_lockdep_assert() to add an informative third
argument.
Also, add a pair of rcu_lockdep_assert() calls from within
rcu_note_context_switch(), one complaining if a context switch occurs
in an RCU-bh read-side critical section and another complaining if a
context switch occurs in an RCU-sched read-side critical section.
These are present only if the PROVE_RCU kernel parameter is enabled.
Finally, fix some checkpatch whitespace complaints in lockdep.c.
Again, you must enable PROVE_RCU to see these new diagnostics. But you
are enabling PROVE_RCU to check out new RCU uses in any case, aren't you?
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The IEEE 1588 standard defines two kinds of messages, event and general
messages. Event messages require time stamping, and general do not. When
using UDP transport, two separate ports are used for the two message
types.
The BPF designed to recognize event messages incorrectly classifies L2
general messages as event messages. This commit fixes the issue by
extending the filter to check the message type field for L2 PTP packets.
Event messages are be distinguished from general messages by testing
the "general" bit.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an event to monitor comm value changes of tasks. Such an event
becomes vital, if someone desires to control threads of a process in
different manner.
A natural characteristic of threads is its comm value, and helpfully
application developers have an opportunity to change it in runtime.
Reporting about such events via proc connector allows to fine-grain
monitoring and control potentials, for instance a process control daemon
listening to proc connector and following comm value policies can place
specific threads to assigned cgroup partitions.
It might be possible to achieve a pale partial one-shot likeness without
this update, if an application changes comm value of a thread generator
task beforehand, then a new thread is cloned, and after that proc
connector listener gets the fork event and reads new thread's comm value
from procfs stat file, but this change visibly simplifies and extends the
matter.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
That flag no longer makes sense, since we don't look up automount points
as eagerly any more. Additionally, it turns out that the NO_AUTOMOUNT
handling was buggy to begin with: it would avoid automounting even for
cases where we really *needed* to do the automount handling, and could
return ENOENT for autofs entries that hadn't been instantiated yet.
With our new non-eager automount semantics, one discussion has been
about adding a AT_AUTOMOUNT flag to vfs_fstatat (and thus the
newfstatat() and fstatat64() system calls), but it's probably not worth
it: you can always force at least directory automounting by simply
adding the final '/' to the filename, which works for *all* of the stat
family system calls, old and new.
So AT_NO_AUTOMOUNT (and thus LOOKUP_NO_AUTOMOUNT) really were just a
result of our bad default behavior.
Acked-by: Ian Kent <raven@themaw.net>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we've now turned around and made LOOKUP_FOLLOW *not* force an
automount, we want to add the ability to force an automount event on
lookup even if we don't happen to have one of the other flags that force
it implicitly (LOOKUP_OPEN, LOOKUP_DIRECTORY, LOOKUP_PARENT..)
Most cases will never want to use this, since you'd normally want to
delay automounting as long as possible, which usually implies
LOOKUP_OPEN (when we open a file or directory, we really cannot avoid
the automount any more).
But Trond argued sufficiently forcefully that at a minimum bind mounting
a file and quotactl will want to force the automount lookup. Some other
cases (like nfs_follow_remote_path()) could use it too, although
LOOKUP_DIRECTORY would work there as well.
This commit just adds the flag and logic, no users yet, though. It also
doesn't actually touch the LOOKUP_NO_AUTOMOUNT flag that is related, and
was made irrelevant by the same change that made us not follow on
LOOKUP_FOLLOW.
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check device's LPM capability by examining the bmAttibutes field of the
USB2.0 Extension Descriptor.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit gets BOS(Binary Device Object Store) descriptor set for Super
Speed devices and High Speed devices which support BOS descriptor.
BOS descriptor is used to report additional USB device-level capabilities
that are not reported via the Device descriptor. By getting BOS descriptor
set, driver can check device's device-level capability such as LPM
capability.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IEEE 1588 standard (PTP) has a provision for a "one step" mode, where
time stamps on outgoing event packets are inserted into the packet by the
hardware on the fly. This patch adds a new flag for the SIOCSHWTSTAMP
ioctl that lets user space programs request this mode.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct pm_domain_data data type is defined in such a way that
adding new fields specific to the generic PM domains code will
require include/linux/pm.h to be modified. As a result, data types
used only by the generic PM domains code will be defined in two
headers, although they all should be defined in pm_domain.h and
pm.h will need to include more headers, which won't be very nice.
For this reason change the definition of struct pm_subsys_data
so that its domain_data member is a pointer, which will allow
struct pm_domain_data to be subclassed by various PM domains
implementations. Remove the need_restore member from
struct pm_domain_data and make the generic PM domains code
subclass it by adding the need_restore member to the new data type.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Merge commit e8b364b88c
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
Conflicts:
drivers/base/power/clock_ops.c
As mentioned by http://www.microsoft.com/whdc/device/input/DigitizerDrvs_touch.mspx
multitouch devices are those that have the input report HID_CONTACTID.
This patch detects this and unloads the generic-usb driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If optional discard support in dm-crypt is enabled, discards requests
bypass the crypt queue and blocks of the underlying device are discarded.
For the read path, discarded blocks are handled the same as normal
ciphertext blocks, thus decrypted.
So if the underlying device announces discarded regions return zeroes,
dm-crypt must disable this flag because after decryption there is just
random noise instead of zeroes.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Device drivers that create and destroy SR-IOV virtual functions via
calls to pci_enable_sriov() and pci_disable_sriov can cause catastrophic
failures if they attempt to destroy VFs while they are assigned to
guest virtual machines. By adding a flag for use by the KVM module
to indicate that a device is assigned a device driver can check that
flag and avoid destroying VFs while they are assigned and avoid system
failures.
CC: Ian Campbell <ijc@hellion.org.uk>
CC: Konrad Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The EFR (Enhenced-Features-Register) is located at a different offset
than the other devices supporting UART_CAP_EFR. This change add a special
setup quick to set UPF_EXAR_EFR on the port. UPF_EXAR_EFR is then used to
the port type to PORT_XR17D15X since it is for sure a XR17D15X uart.
Signed-off-by: Søren Holm <sgh@sgh.dk>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm: extension capability for new address space layout
[S390] kvm: fix address mode switching
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
