With MDP5 as a new device, we need to do less for MDP when initializing
modeset after all the components are bound.
Create mdp5_kms_init2/destroy2 funcs that inits modeset. These will
eventually replace the older kms_init/destroy funcs.
In the new kms_init2, the platform_device used is the one corresponding
to the new MDP5 platform_device. The new change here is that the irq is
now retrieved using irq_of_parse_and_map(), since MDP5 is a child interrupt
of the MDSS interrupt controller.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to have a tree-like device hierarchy between MDSS and its
sub-blocks (MDP5, DSI, HDMI, eDP etc), we need to create a separate
device/driver for MDP5. Currently, MDP5 and MDSS are squashed
together are are tied to the top level platform_device, which is
also the one used to create drm_device.
The mdp5_kms_init code is split into two parts. The part where device
resources are allocated are associated with the MDP5 driver's probe,
the rest is executed later when we initialize modeset.
With this change, unlike MDP4, the MDP5 platform_device isn't tied to
the top level drm_device anymore. The top level drm_device is now
associated with a platform device that corresponds to MDSS wrapper
hardware.
Create mdp5_init/destroy funcs that will be used by the MDP5 driver
probe/remove. Use the HW_VERSION register in the MDP5 register address
space. Both the MDSS and MDP VERSION registers give out identical
version info.
The older mdp5_kms_init code is left as is for now, this would be removed
later when we have all the pieces to support the new device hierarchy.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SoCs that contain MDP5 have a top level wrapper called MDSS that manages
clocks, power and irq for the sub-blocks within it.
Currently, the MDSS portions are stuffed into the MDP5 driver. This makes
it hard to represent the DT bindings in the correct way. We create a top
level MDSS helper that handles these parts. This is essentially moving out
some of the mdp5_kms irq code and MDSS register space and keeping it as a
separate entity. We haven't given any clocks to the top level MDSS yet,
but a AHB clock would be added in the future to access registers.
One thing to note is that the resources allocated by this helper are
tied to the top level platform_device (the one that allocates the
drm_device struct too). This device would be the parent to MDSS
sub-blocks like MDP5, DSI, eDP etc.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver gets the irq number using platform_get_irq on the main kms
platform device. This works fine since both MDP4 and MDP5 currently
have a flat device hierarchy. The platform device tied with the
drm_device points to the MDP DT node in both cases.
This won't work when MDP5 supports a tree-like hierarchy. In this
case, the platform device tied to the top level drm_device is the
MDSS DT node, and the irq we need for KMS is the one generated by
MDP5, not MDSS.
Get the irq number from the MDP4/5 kms driver itself. Each driver
can later provide the irq number based on what device hierarchy it
uses.
While we're at it, call drm_irq_install only when we have a valid KMS
driver.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These aren't used. Probably left overs when driver was refactored to
support both MDP4 and MDP5.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A more standard DT binding describing data lanes already exists here:
Documentation/devicetree/bindings/media/video-interfaces.txt
Use this binding instead of "qcom,data-lane-map". One difference
in the standard binding w.r.t to the existing binding is that it
provides a logical to physical mapping instead of the other way
round. Tweak the code to translate the data the way we want it.
The MSM DSI DT bindings aren't used anywhere at the moment, so
it's okay to update this property.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host links to the DSI PHY device using a custom binding. Switch to
the generic PHY bindings. The DSI PHY driver itself doesn't use the common
PHY framework for now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI interface is going to have two ports defined in its device node.
The first port is always going to be the link between the MDP output
and the input to DSI, the second port is going to be the link between
the DSI output and the connected panel/bridge:
----- ----- -------
| MDP | ------> | DSI | ------> | Panel |
----- ----- -------
(Port 0) (Port 1)
Until now, there was only one Port representing the output. Update the
DSI host driver such that it parses Port #1 for a connected device.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fix some issues with MDP4 clocks:
- mdp4_dtv_encoder tries to get "src_clk", which is a RCG(TV_SRC) in
MSM8960 and APQ8064. This isn't something the driver should access or
configure. Instead of this, configure the "mdp_clk" (MDP_TV_CLK), a
branch clock in MMCC that has the TV_SRC as its parent. Setting
rate/enabling the "mdp_clk" will eventually configure "src_clk", which
is what we want.
- Rename "mdp_clk" to "tv_clk" because that's slightly less confusing.
- Rename "mdp_axi_clk" to "bus_clk" because that's what we do elsewhere
too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver expects DT to provide the parent to MDP core clock. The only
operation done to the parent clock is to set a rate. This can be
achieved by setting the rate on the core clock itsef. Don't try to
get the parent clock anymore.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm_iommu_map/unmap funcs have debug prints to show the list of
VA:PA mappings. Use the correct variable to print the VAs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The u32 type used to pass the physical addresses to iommu_map can't
accommodate 64 bit addresses. Move to dma_addr_t to ensure wrong
addresses aren't provided to the IOMMU driver.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
We already have a fallback in place to fill out the unique from
dev->unique, which is set to something reasonable in drm_dev_alloc.
Which means we only need to have a special set_busid for pci devices,
to be able to care the backwards compat code for drm 1.1 around, which
libdrm still needs.
While developing and testing this patch things blew up in really
interesting ways, and the code is rather confusing in naming things
between the kernel code, ioctl #defines and libdrm. For the next brave
dragon slayer, document all this madness properly in the userspace
interface section of gpu.tmpl.
v2: Make drm_dev_set_unique static and update kerneldoc.
v3: Entire rewrite, plus document what's going on for posterity in the
gpu docbook uapi section.
v4: Drop accidental amdgpu hunk (Emil).
v5: Drop accidental omapdrm vblank counter change (Emil).
v6: Rebase on top of the sphinx conversion.
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> (virt_gpu)
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-7-git-send-email-chris@chris-wilson.co.uk
For all outputs except DSI we have a 1:1 relationship between connectors
and encoders and the driver is relying on the atomic helpers: we can
drop the custom ->best_encoder() and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-9-git-send-email-boris.brezillon@free-electrons.com
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
lockless gem bo freeing patches (and the oddball related patch) for all
the drivers who's maintainers are asleep at the helm - includes you ;-)
I based this on top of drm-fixes to include Chris' fix for the cma issue.
* tag 'topic/lockless-gem-bo-freeing-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/arcpgu: Use lockless gem BO free callback
drm/sun4i: Use lockless gem BO free callback
drm/omapdrm: Nuke dummy fb->dirty callback
drm/msm: Nuke dummy fb->dirty callback
drm/rockchip: Use cma gem vm ops
drm/sti: Use lockless gem BO free callback
drm: sti: remove useless call to dev->struct_mutex
drm/virtio: Use lockless gem BO free callback
drm/tilcdc: Use lockless gem BO free callback
drm/shmob: Use lockless gem BO free callback
drm/rockchip: Use lockless gem BO free callback
drm/rcar-du: Use lockless gem BO free callback
drm/qxl: Use lockless gem BO free callback
drm/nouveau: Use lockless gem BO free callback
drm/mga200g: Use lockless gem BO free callback
drm/fls-dcu: Use lockless gem BO free callback
drm/cirrus: Use lockless gem BO free callback
drm/bochs: Use lockless gem BO free callback
drm/atmel: Use lockless gem BO free callback
drm/ast: Use lockless gem BO free callback
...
If submit fails, before fence is created or before submit is added to
submit-list, then unitialized fields cause problems in the clean-up
path.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some, but not all, callers of obj->vmap() would check if return
IS_ERR(). So let's actually return an error if vmap() fails. And fixup
the call-sites that were not handling this properly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
... and use it in msm&vc4. Again just want to encapsulate
drm_atomic_state internals a bit.
The const threading is a bit awkward in vc4 since C sucks, but I still
think it's worth to enforce this. Eventually I want to make all the
obj->state pointers const too, but that's a lot more work ...
v2: Provide safe macro to wrap up the unsafe helper better, suggested
by Maarten.
v3: Fixup subject (Maarten) and spelling fixes (Eric Engestrom).
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Eric Engestrom <eric.engestrom@imgtec.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464877304-4213-1-git-send-email-daniel.vetter@ffwll.ch
We want to hide drm_atomic_state internals
v2: Review from Maarten:
- remove whitespace change in rockchip driver that slipped in.
- use drm_crtc_mask insted of open-coding it.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464818821-5736-4-git-send-email-daniel.vetter@ffwll.ch
Frist -misc pull for 4.8, with pretty much just random all over plus a few
more lockless gem BO patches acked/reviewed by driver maintainers.
I'm starting a bit earlier this time around because there's a few invasive
patch series to land (nonblocking atomic prep work, fence prep work,
rst/sphinx kerneldoc finally happening) and I need a baseline with all the
branches merged.
* tag 'topic/drm-misc-2016-06-01' of git://anongit.freedesktop.org/drm-intel: (21 commits)
drm/vc4: Use lockless gem BO free callback
drm/vc4: Use drm_gem_object_unreference_unlocked
drm: Initialize a linear gamma table by default
drm/vgem: Use lockless gem BO free callback
drm/qxl: Don't set a gamma table size
drm/msm: Nuke dummy gamma_set/get functions
drm/cirrus: Drop redundnant gamma size check
drm/fb-helper: Remove dead code in setcolreg
drm/mediatek: Use lockless gem BO free callback
drm/hisilicon: Use lockless gem BO free callback
drm/hlcd: Use lockless gem BO free callback
vga_switcheroo: Support deferred probing of audio clients
vga_switcheroo: Add helper for deferred probing
virtio-gpu: fix output lookup
drm/doc: Unify KMS Locking docs
drm/atomic-helper: Do not call ->mode_fixup for CRTC which will be disabled
Fix annoyingly awkward typo in drm_edid_load.c
drm/doc: Drop vblank_disable_allow wording
drm: use seqlock for vblank time/count
drm/mm: avoid possible null pointer dereference
...
Again the fbdev emulation gamma_set/get functions are only needed for
drivers that try to also use 8bpp paletted mode. Which msm doesn't, so
this is dead code. Let's rip it out.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-7-git-send-email-daniel.vetter@ffwll.ch
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
drm_gem_object_lookup() has never required the drm_device for its file
local translation of the user handle to the GEM object. Let's remove the
unused parameter and save some space.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Fixup kerneldoc too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The load/unload drm_driver ops are deprecated. They should be removed as
they result in creation of devices visible to userspace even before
the drm_device is registered.
Drop these ops and use drm_dev_alloc/register and drm_dev_unregister/unref
to explicitly create and destroy the drm device in the msm platform
driver's bind and unbind ops. With this in use, the drm connectors are
only registered once the drm_device is registered.
It also fixes the issue of stray debugfs files after the msm module is
removed. With this, all the debugfs files are removed, and allows
successive module insertions/removals.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Move the drm_connector registration from the encoder(HDMI/DSI etc) drivers
to the msm platform driver. This will simplify the task of ensuring that
the connectors are registered only after the drm_device itself is
registered.
The connectors' destroy ops are made to use kzalloc instead of
devm_kzalloc to ensure that that the connectors can be successfully
unregistered when the msm driver module is removed. The memory for the
connectors is unallocated when drm_mode_config_cleanup() is called
during either during an error or during driver remove.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Calling the legacy gpio_free on an invalid GPIO (a GPIO numbered -1)
results in kernel warnings. This causes a lot of backtraces when
we try to unload the drm/msm module.
Call gpio_free only on valid GPIOs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Track the pid per submit, so we can print the name of the task which
submitted the batch that caused the gpu to hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
At this point, there is nothing left to fail. And submit already has a
fence assigned and is added to the submit_list. Any problems from here
on out are asynchronous (ie. hangcheck/recovery).
Signed-off-by: Rob Clark <robdclark@gmail.com>
The MDP4 driver tries to request and set voltages for regulators required
by the DSI PLLs.
Firstly, the MDP4 driver shouldn't manage the DSI regulators, this should
be handled in the DSI driver. Secondly, it shouldn't try to set a fixed
voltage for regulators. Voltage constraints should be specified on the
regulator via DT and managed by the regulator core.
Remove all the DSI PLL regulator related code from the MDP4 driver. It's
managed in the DSI driver for MSM8960/APQ8064 already.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The eDP driver tries to set a fixed voltage for one of its regulators(vdda)
before enabling it. This shouldn't be done by the driver, the voltage
constraints should be specified on the regulator via DT and managed by
the regulator core. A driver should call regulator_set_voltage only if
it needs to change the voltage during runtime. Drop the
regulator_set_voltage call. Mention in a comment the voltage that the
regulator expects.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The voltage changing code in this driver is broken and should be
removed. The driver sets a single, exact voltage on probe. Unless
there is a very good reason for this (which should be documented in
comments) constraints like this need to be set via the machine
constraints, voltage setting in a driver is expected to be used in cases
where the voltage varies at runtime.
In addition client drivers should almost never be calling
regulator_can_set_voltage(), if the device needs to set a voltage it
needs to set the voltage and the regulator core will handle the case
where the regulator is fixed voltage. If the driver simply skips
setting the voltage if it doesn't have permission then it should just
not bother in the first place.
Originally authored by Mark Brown <broonie@kernel.org>
Remove the min/max voltage data entries per SoC managed by the driver.
These aren't needed as we don't try to set voltages any more. Mention in
comments the voltages that each regulator expects.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Here, a location is reset to NULL before being passed to PTR_ERR.
So, PTR_ERR should be called before its argument is reassigned
to NULL. Further to simplify things use PTR_ERR_OR_ZERO instead
of PTR_ERR and IS_ERR.
Problem found using Coccinelle.
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
[fixed fmt string warning (s/%ld/%d/)]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Android needs XBGR8888 format. Add all the missing 32-bpp formats
without alpha for completeness.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent cleanup removed the only user of the 'kms' variable in
msm_preclose(), causing a harmless compiler warning:
drivers/gpu/drm/msm/msm_drv.c: In function 'msm_preclose':
drivers/gpu/drm/msm/msm_drv.c:468:18: error: unused variable 'kms' [-Werror=unused-variable]
This removes the variable as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4016260ba4 ("drm/msm: fix bug after preclose removal")
Signed-off-by: Rob Clark <robdclark@gmail.com>
It is no longer true that we discard all in-flight submits on recover
(these days we only discard the first one that hung). After the first
re-submitted batch completes it would overwrite the fence with a correct
value, but there would be a window of time which showed all re-submitted
batches as already complete.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was only used for atomic commit these days. So instead just give
atomic it's own work-queue where we can do a block on each bo in turn.
Simplifies things a whole bunch and makes the 'struct fence' conversion
easier.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Better encapsulate the per-timeline stuff into fence-context. For now
there is just a single fence-context, but eventually we'll also have one
per-CRTC to enable fully explicit fencing.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Split up locking and pinning buffers in the submit path. This is needed
because we'll want to insert fencing in between the two steps.
This makes things end up looking more similar to etnaviv submit code
(which was originally modelled on the msm code but has already added
'struct fence' support).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since we already track the array of bo's in the submit object, just
unconditionally take and drop ref's per submit (rather than only taking
ref's if bo is not already active). This simplifies later patches.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This function had copies in 3 different files. Unify them in kernel.h.
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@intel.com> [drm/i915/]
Acked-by: Rob Clark <robdclark@gmail.com> [drm/msm/]
Acked-by: Lucas Stach <l.stach@pengutronix.de> [drm/etinav/]
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoids drivers knowing where the kref is stored.
[airlied: add kerneldoc]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit 53190c7194
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Mon Jan 25 22:16:49 2016 +0100
Commit: Daniel Vetter <daniel.vetter@ffwll.ch>
CommitDate: Mon Feb 8 09:55:50 2016 +0100
drm/msm: Nuke preclose hooks
Left around the unused (and null) preclose fxn ptr, and things
predictibly explode when you try to call that.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch set nukes all the dummy crtc mode_fixup implementations.
(made on top of Daniel topic/drm-misc branch)
Signed-off-by: Carlos Palminha <palminha@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Global symbols in the kernel should be prefixed by the name
of the subsystem and/or driver to avoid conflicts when all
code is built-in.
In this case, function names like 'hdmi_register' or 'hdmi_set_mode'
are way too generic for an MSM specific DRM driver, so I'm renaming
them all to msm_hdmi_* here.
I also rename a lot of the 'static' symbols along with the global
names for consistency, even though those are relatively harmless;
they might only be slightly confusing when they show up in
backtraces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Not sure where it came from, but seem unintentional. And also not
needed on a420, so let's just drop it.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need this for GL_TIMESTAMP queries.
Note: currently only supported on a4xx.. a3xx doesn't have this
always-on counter. I think we could emulate it with the one CP
counter that is available, but for now it is of limited usefulness
on a3xx (since we can't seem to do time-elapsed queries in any sane
way with the existing firmware on a3xx, and if you are trying to do
profiling on a tiler you want time-elapsed). We can add that later
if it becomes useful.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Existing userspace wouldn't get this far, since getparam ioctl would
have failed and it would have bailed out creating a screen/context.
But all the same, we shouldn't let evil or confused userspace cause a
null ptr deref.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As described in the downstream/kgsl driver:
Sometimes the RPTR shadow memory is unreliable causing timeouts
in adreno_idle(). Read it directly from the register instead.
Signed-off-by: Craig Stout <cstout@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This fixes the following build failure:
drivers/gpu/drm/msm/dsi/pll/dsi_pll_28nm.o: In function `msm_dsi_pll_28nm_8960_init':
dsi_pll_28nm.c:(.text+0x1198): multiple definition of `msm_dsi_pll_28nm_8960_init'
drivers/gpu/drm/msm/dsi/pll/dsi_pll.o:dsi_pll.c:(.text+0x0): first defined here
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI driver is currently unaware of how the DSI physical data lanes
are mapped to the logical lanes provided by the DSI controller.
Create a DT binding "qcom,data-lane-map" that provides this information
on a given platform.
The MSM DSI controller is restricted in terms of what all mappings
it can support. The lane polarity is fixed for all the lanes, the clock
lanes are fixed, and the data lanes can be swapped among each other only
for a few combinations. Apply these restrictions when we parse the DT
data.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
VDD regulator input was specified for MSM8916. It turns our that this
regulator is used for the display panels used on MSM8916 platforms, but
not the DSI controller itself. Drop this regulator from the list.
Reported-by: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With the implementation of of_graph parsing, it isn't any longer
necessary for msm_host->device node to be same as dsi->dev.of_node. This
only holds true when the connected device is also a child of the dsi_host.
In the case of external bridge chips belonging to a different control
bus, these are guaranteed to be different.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We have a msm_fbev_free function to uninit fb_helper stuff, but we aren't
using it. Call it in msm_unload.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
attach_dev gets called in mdp4_kms_init, but there is no corresponding
detach_dev called in the error path or in the kms driver unload path.
Detach and destroy mmu in mdp4_destroy.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Assign drm_atomic_helper_crtc_set_property helper to MDP4 and MDP5
crtcs' set_property ops. This replaces the custom funcs that
returned an error even for standard crtc properties.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the HDMI PHY/PLL found in MSM8996/APQ8096.
Unlike the previous PHYs supported in the driver, this doesn't need
the powerup/powerdown ops. The PLL prepare/unprepare clock ops
enable/disable the phy itself.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
- Create separate domains for 8960 PHY and PLL
- Create separate domains for 8x60 PHY
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove the old PHY ops managed by hdmi_platform_config and use them as ops
provided by the HDMI PHY driver.
Remove the old HDMI 8960 PLL code that used the top level HDMI TX mmio
base.
NOTE: With this commit, HDMI functionality will break until the HDMI
PHY/PLL register offsets in hdmi.xml.h aren't updated to be used as
separate domains.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make HDMI core get its PHY by parsing the "phys" phandle. The core will use
this PHY reference to enable/disable PHY. The driver defers probe until PHY
isn't available.
The DT bindings used here is the same as the one used for PHYs using the
common PHY framework bindings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a helper to initialize PLL in the PHY driver. HDMI PLLs are going to
have their own mmio base different from that of PHY.
For the clock code in hdmi_phy_8960.c, some changes were needed for it to
work with the updated register offsets. Create a copy of the updated clock
code in hdmi_pll_8960.c, instead of rewriting it in hdmi_phy_8960.c
itself. This removes the need to place CONFIG_COMMON_CLOCK checks all
around, makes the code more legible, and also removes some old checkpatch
warnings with the original code.
The older hdmi pll clock ops in hdmi_phy_8960.c will be removed later. The
driver will use these until the HDMI PHY/PLL register offsets aren't
considered as separate domains (i.e. their offsets start from 0).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a PHY device that represents the TX PHY and PLL parts of the HDMI
block.
This makes management of PHY specific resources (regulators and clocks)
much easier, and makes the PHY and PLL usable independently. It also
simplifies the core HDMI driver, which currently assigns phy ops among
many other things.
The PHY driver implementation done here is very similar to the PHY driver
we already have for DSI.
Keep the old hdmi_phy_funcs ops for now. The driver will use these until
the HDMI PHY/PLL register offsets aren't considered as separate
domains (i.e. their offsets start from 0).
The driver doesn't use the common PHY framework for now. This is because
it's hard to map our ops with the ops provided by the framework. The
bindings used for this is the generic phy bindings. So, this can be
adapted to the PHY framework in the future, if possible.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some platforms may not have a HPD gpio line to detect Hot Plug signal from
the connector. They need to rely only on reading REG_HDMI_HPD_INT_STATUS
for HPD.
Modify hdmi_connector_detect logic such that it checks for HPD only using
the status register if there is no HPD gpio.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make gpio allocation and usage iterative by parsing the gpios on a given
platform from a list. This gives us flexibility over what all gpios exist
for a platform, whether they are input or output, and what value they
should be set to.
In particular, this will make HDMI on 8x96 platforms easier to integrate
with the driver, as it doesn't have a HPD gpio input to them. Also, it
cleans things up a bit.
We still use the legacy gpio api here, as we might need to backport this
driver to downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Misc stuff all over:
- more mode_fixup removal from Carlos, there's another final pile still
left.
- final bits of vgaswitcheroo from Lukas for apple gmux, we're still
discussing an api cleanup patch to make it a bit more abuse-safe as a
follow-up
- dp aux interface for userspace for tools&tests from Rafael Antognolli
- actual interface parts for dma-buf flushing for userspace mmap
- few small bits all over
- vgaswitcheroo support for apple gmux from Lukas Wunner
- checks for ->mode_fixup in non-atomic helpers from Carlos Palminha, plus
removing dummy funcs from drivers. Carlos promised to follow up with
more, since there's lots more silly dummy functions around.
- dma-buf patches from Tiago, except the ioctl itself (that needed a
respin to address review from David Herrmann)
- encoder mask for atomic from Maarten
- bunch of random things all over.
* tag 'topic/drm-misc-2016-02-18' of git://anongit.freedesktop.org/drm-intel: (57 commits)
drm/udl: Use module_usb_driver
drm: fixes crct set_mode when crtc mode_fixup is null.
drm/tilcdc: removed optional dummy encoder mode_fixup function.
drm/sti: removed optional dummy encoder mode_fixup function.
drm/rockchip: removed optional dummy encoder mode_fixup function.
drm/qxl: removed optional dummy encoder mode_fixup function.
drm/mgag200: removed optional dummy encoder mode_fixup function.
drm/msm/mdp: removed optional dummy encoder mode_fixup function.
drm/imx: removed optional dummy encoder mode_fixup function.
drm/gma500: removed optional dummy encoder mode_fixup function.
drm/radeon: removed optional dummy encoder mode_fixup function.
drm/cirrus: removed optional dummy encoder mode_fixup function.
drm/bochs: removed optional dummy encoder mode_fixup function.
drm/ast: removed optional dummy encoder mode_fixup function.
drm/amdgpu: removed optional dummy encoder mode_fixup function.
drm/exynos: removed optional dummy encoder mode_fixup function.
drm/udl: removed optional dummy encoder mode_fixup function.
drm/virtio: removed optional dummy encoder mode_fixup function.
drm/fb_helper: Use add_one_connector in add_all_connectors.
drm/fb_helper: Use correct allocation count for arrays.
...
After the drm_device_is_unplugged() was removed, the 'dev' variable is now
unused, and we get a warning for that:
drivers/gpu/drm/msm/msm_fbdev.c: In function 'msm_fbdev_mmap':
drivers/gpu/drm/msm/msm_fbdev.c:65:21: error: unused variable 'dev' [-Werror=unused-variable]
This removes the variable as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e9f8250f2f ("drm/msm: remove the drm_device_is_unplugged check")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455181810-3910161-1-git-send-email-arnd@arndb.de
We need this in userspace for interpreting some of the perf ctrs.
Note possibly not quite sufficient if we had some frequency mgmt
approach other than race-to-idle. Not really sure what the best
thing to do if we did. Although displaying results as a percentage
of max frequence seems sensible(ish) if we did.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This flag is only used for drm/udl.
Signed-off-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454709464-2536-1-git-send-email-hshi@chromium.org
First drm-misc pull req for 4.6. Big one is the drm_event cleanup, which
is also prep work for adding android fence support to kms (Gustavo is
planning to do that). Otherwise random small bits all over.
* tag 'topic/drm-misc-2016-02-08' of git://anongit.freedesktop.org/drm-intel: (33 commits)
gma500: clean up an excessive and confusing helper
drm/gma500: remove helper function
drm/vmwgfx: Nuke preclose hook
drm/vc4: Nuke preclose hook
drm/tilcdc: Nuke preclose hook
drm/tegra: Stop cancelling page flip events
drm/shmob: Nuke preclose hook
drm/rcar: Nuke preclose hook
drm/omap: Nuke close hooks
drm/msm: Nuke preclose hooks
drm/imx: Unconfuse preclose logic
drm/exynos: Remove event cancelling from postclose
drm/atmel: Nuke preclose
drm/i915: Nuke intel_modeset_preclose
drm: Nuke vblank event file cleanup code
drm: Clean up pending events in the core
drm/vblank: Use drm_event_reserve_init
drm/vmwgfx: fix a NULL dereference
drm/crtc-helper: Add caveat to disable_unused_functions doc
drm/gma500: Remove empty preclose hook
...
They only complete the page flip events to avoid oops when the drm
file closes. The core takes care of that now and we can remove this
code.
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-8-git-send-email-daniel.vetter@ffwll.ch
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.5. I don't think I've missed
anything too major, I'm mostly back at work now but I'll probably get
some sleep in 5 years time.
Summary:
New drivers:
- etnaviv:
GPU driver for the 3D core on the Vivante core used in numerous
ARM boards.
Highlights:
Core:
- Atomic suspend/resume helpers
- Move the headers to using userspace friendlier types.
- Documentation updates
- Lots of struct_mutex removal.
- Bunch of DP MST fixes from AMD.
Panel:
- More DSI helpers
- Support for some new basic panels
i915:
- Basic Kabylake support
- DP link training and detect code refactoring
- fbc/psr fixes
- FIFO underrun fixes
- SDE interrupt handling fixes
- dma-buf/fence support in pageflip path.
- GPU side for MST audio support
radeon/amdgpu:
- Drop UMS support
- GPUVM/Scheduler optimisations
- Initial Powerplay support for Tonga/Fiji/CZ/ST
- ACP audio prerequisites
nouveau:
- GK20a instmem improvements
- PCIE link speed change support
msm:
- DSI support for msm8960/apq8064
tegra:
- Host1X support for Tegra210 SoC
vc4:
- 3D acceleration support
armada:
- Get rid of struct mutex
tda998x:
- Atomic modesetting support
- TMDS clock limitations
omapdrm:
- Atomic modesetting support
- improved TILER performance
rockchip:
- RK3036 VOP support
- Atomic modesetting support
- Synopsys DW MIPI DSI support
exynos:
- Runtime PM support
- of_graph binding for DP panels
- Cleanup of IPP code
- Configurable plane support
- Kernel panic fixes at release time"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (711 commits)
drm/fb_cma_helper: Remove implicit call to disable_unused_functions
drm/amdgpu: add missing irq.h include
drm/vmwgfx: Fix a width / pitch mismatch on framebuffer updates
drm/vmwgfx: Fix an incorrect lock check
drm: nouveau: fix nouveau_debugfs_init prototype
drm/nouveau/pci: fix check in nvkm_pcie_set_link
drm/amdgpu: validate duplicates first
drm/amdgpu: move VM page tables to the LRU end on CS v2
drm/ttm: add ttm_bo_move_to_lru_tail function v2
drm/ttm: fix adding foreign BOs to the swap LRU
drm/ttm: fix adding foreign BOs to the LRU during init v2
drm/radeon: use kobj_to_dev()
drm/amdgpu: use kobj_to_dev()
drm/amdgpu/cz: force vce clocks when sclks are forced
drm/amdgpu/cz: force uvd clocks when sclks are forced
drm/amdgpu/cz: add code to enable forcing VCE clocks
drm/amdgpu/cz: add code to enable forcing UVD clocks
drm/amdgpu: fix lost sync_to if scheduler is enabled.
drm/amd/powerplay: fix static checker warning for return meaningless value.
drm/sysfs: use kobj_to_dev()
...
Merge second patch-bomb from Andrew Morton:
- more MM stuff:
- Kirill's page-flags rework
- Kirill's now-allegedly-fixed THP rework
- MADV_FREE implementation
- DAX feature work (msync/fsync). This isn't quite complete but DAX
is new and it's good enough and the guys have a handle on what
needs to be done - I expect this to be wrapped in the next week or
two.
- some vsprintf maintenance work
- various other misc bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (145 commits)
printk: change recursion_bug type to bool
lib/vsprintf: factor out %pN[F] handler as netdev_bits()
lib/vsprintf: refactor duplicate code to special_hex_number()
printk-formats.txt: remove unimplemented %pT
printk: help pr_debug and pr_devel to optimize out arguments
lib/test_printf.c: test dentry printing
lib/test_printf.c: add test for large bitmaps
lib/test_printf.c: account for kvasprintf tests
lib/test_printf.c: add a few number() tests
lib/test_printf.c: test precision quirks
lib/test_printf.c: check for out-of-bound writes
lib/test_printf.c: don't BUG
lib/kasprintf.c: add sanity check to kvasprintf
lib/vsprintf.c: warn about too large precisions and field widths
lib/vsprintf.c: help gcc make number() smaller
lib/vsprintf.c: expand field_width to 24 bits
lib/vsprintf.c: eliminate potential race in string()
lib/vsprintf.c: move string() below widen_string()
lib/vsprintf.c: pull out padding code from dentry_name()
printk: do cond_resched() between lines while outputting to consoles
...
Convert the raw unsigned long 'pfn' argument to pfn_t for the purpose of
evaluating the PFN_MAP and PFN_DEV flags. When both are set it triggers
_PAGE_DEVMAP to be set in the resulting pte.
There are no functional changes to the gpu drivers as a result of this
conversion.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Last (very likely at least) drm-misc pull for 4.5. 3 big things:
- piles of docs for kms vtables.
- drm.debug dmesg output prettification from Ville (i915 parts are for 4.6
I think)
- connector mode probing/validating/merging cleanup from Ville.
[airlied : fix drm_encoder_init conflict.]
* tag 'topic/drm-misc-2015-12-14' of git://anongit.freedesktop.org/drm-intel: (43 commits)
drm: modes: Revert cc344980c7 "replace simple_strtoul by kstrtouint"
drm: Expand the drm_helper_probe_single_connector_modes() docs
drm: Allow override_edid to override the firmware EDID
drm/sti: Drop bogus drm_mode_sort() call
drm: Drop drm_helper_probe_single_connector_modes_nomerge()
drm: Only merge mode type bits between new probed modes
drm: Flatten drm_mode_connector_list_update() a bit
drm: Rename MODE_UNVERIFIED to MODE_STALE
drm: Don't overwrite UNVERFIED mode status to OK
drm: Add plane->name and use it in debug prints
drm: Add crtc->name and use it in debug messages
drm: Use driver specified encoder name
drm: Pass 'name' to drm_encoder_init()
drm: Pass 'name' to drm_universal_plane_init()
drm: Pass 'name' to drm_crtc_init_with_planes()
drm: Documentation style guide
drm: Document drm_encoder/crtc_helper_funcs
drm: Move drm_display_mode an related docs into kerneldoc
drm/atomic-helper: Mention the new system/resume helpers the docs
drm: Document drm_connector_helper_funcs
...
WARN_ON() takes a condition rather than a format string. This patch
converted WARN_ON() to WARN() instead.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
in case of failed to get iova, function was returning without releasing
the mutex. Added it.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit ef4c6270bf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For DSIv2 to work, we need to enable MMSS_AHB_ARB_MASTER_PORT in
MMSS_SFPB. We enable the required bitfield by retrieving MMSS_SFPB
regmap pointer via syscon.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently use iommu allocated DMA buffers for sending DSI commands.
DSIv2 doesn't have a port connected to the MDP iommu. Therefore, it
can't use iommu allocated buffers to fetch DSI commands.
Use a regular contiguous DMA buffer if we are DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a dsi_cfg entry for APQ8064. Since this is the first DSIv2 chip to
be supported, add a list of bus clocks that are required by the DSIv2
block.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSIv2 (DSI on older A family chips) has slightly different link clock
requirements.
First, we have an extra clock called src_clk (with a dedicated RCG).
This is required by the DSI controller to process the pixel data
coming from MDP. It needs to be set at the rate "pclk * bytes_per_pixel".
We also need to explicitly configure esc_clk. On DSI6G chips, we don't
need to set a rate to esc_clk because its RCG is always sourced from
crystal clock (19.2 Mhz in all cases), which is within the escape clock
frequency range in the mipi DSI spec. For chips with DSIv2, the crystal
clock rate may not be within the required range (27Mhz on APQ8064).
Therefore, we derive it from the DSI byte clock. We calculate an esc_clck
rate that is within the mipi spec and also divisible by the byte clock
rate.
When setting rate and enabling the link clocks, we make sure that byte_clk
is configured before esc_clk, and src_clk before pixel_clk. We create two
different link_enable funcs for DSI6G and DSIv2 since the sequences are
different.
We also obtain two extra source clocks (dsi_src_clk and esc_src_clk) and
set their parent to the clocks provided by DSI PLL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Initialize clocks only after we get the DSI host version. This will allow
us to get clocks using a pre-defined list based on the DSI major/minor
version of the host. This is required since clock requirements of
different major DSI revisions(v2 vs 6g) aren't the same.
Modify dsi_get_version to get the interface clock, and then put it after
it is used.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current version checking mechanism works fine for DSI6G blocks. It
doesn't work so well for older generation DSIv2 blocks.
The initial read of REG_DSI_6G_HW_VERSION(offset 0x0) would result in a
read of REG_DSI_CTRL for DSIv2. This register won't necessarily be 0 on
DSIv2. It can be non zero if DSI was previously initialized by the
bootloader.
Instead of reading offset 0x0, we now read offset 0x1f0. For DSIv2, this
register is DSI_VERSION, and is bound to be non-zero. On DSI6G, this
register(offset 0x1f0) is SCRATCH_REGISTER_0, which no one ever seems to
touch, and from all register dumps I'vc seen, holds 0 all the time.
Modify dsi_get_version to read REG_DSI_VERSION to determine whether we
are DSI6G or DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add DSI PLL common clock framework clocks for 8960 PHY.
The PLL here is different from the ones found in B family msm chips. As
before, the DSI provides two clocks to the outside world. dsixpll and
dsixpllbyte (x = 1, 2). dsixpll is a regular clock divider, but
dsixpllbyte is modelled as a custom clock divider.
dsixpllbyte is the starting point of the PLL configuration. It is the
one that sets up the VCO clock rate. We need the VCO clock rate in the
form: F * byteclk, where F is a multiplication factor that varies on
the byte clock the DSI driver is trying to set. We use the custom
clk_ops for dsixpllbyte to ensure that the parent (VCO) is set at this
rate.
An additional divider (POSTDIV1) generates the bitclk. Since bit clock
can be derived from byteclock, we calculate it internally, and don't
expose it as a clock.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We retrieve the byte and pixel source clocks (RCG clocks) in the dsi
driver via DT. These are needed so that we can re-parent these source
clocks if we want to drive it using a different DSI PLL.
We shouldn't get these via DT because they aren't clocks that directly
serve as inputs to the dsi host.
Fortunately, there is a static parent-child link between the
byte_clk_src/pixel_clk_src and byte_clk/pixel_clk clocks. So, we can
retrieve the source clocks via clk_get_parent.
Do this instead of retrieving via DT.
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create DSI encoders during modeset_init. The 2 encoders should ideally be
one command mode and one video mode DSI encoder respectively, but we don't
support command mode yet. We just create 2 of the same because the dsi
driver expects it, we end up using only the first one.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp_kms round_pixclk op creates problems when we have more
interfaces in use. It calls the DTV encoder's helper by default.
Check on encoder type and call the corresponding encoder's
func meant for rounding pixel clock. DSI and LVDS don't require
rounding, so just return rate in their case.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an mdp4 incoder for DSI. Only DSI video mode is supported as of
now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinay Simha BN <vinaysimha@inforcecomputing.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently, the driver defers if it doesn't find a drm_panel. This forces
us to have a drm_panel, if not, the driver isn't usable.
Make the lcdc encoder initialization independent of the availability of
the drm panel. We only check if there is a panel node specified in DT. If
it isn't, then we don't initialize the encoder at all. The panel node is
passed to the lcdc encoder and lvds connector drivers.
The connector driver takes the responsibility to retrieve the drm_panel
from the panel node, and update the status on whether the panel is
connected or not. This makes the panel usable even if the drm_panel
driver is inserted as a module later on.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
modeset_init() for mdp4 isn't very flexible. That makes it hard to add
more interfaces.
Split out the encoder/connector creation code in modeset_init into a
separate function. This is similar to what's done in modeset_init for
mdp5.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove CONFIG_OF checks in adreno_device.c. The downstream bus scaling
stuff is included only when CONFIG_OF is not set. So, remove that too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We now only care about kernels that support DT. Remote the non-DT stuff.
While we're at it, use of_device_get_match_data to retrieve match data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We don't intend to use downstream non-DT kernels anymore, so remove
CONFIG_OF checks.
Update the TODO comment so that we don't forget about max_clk setting
for non APQ8064 chips having MDP4.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create distinct compatible strings for mdp4 and mdp5. Keep "qcom,mdss_mdp"
as is to support downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Support for non-DT kernels was mainly to use v3.4 downstream kernels.
This is no longer a priority now as we have reasonable support upstream.
Remove CONFIG_OF from the top level msm_drv.c file. While we're at it,
clean up the data matching process using of_device_get_match_data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 has line count and frame count registers for each interface. Enable
these counters and use them to implement the get_vblank_timestamp drm
driver op.
The line counter starts with the value 1 at the beginning of the VSYNC
pulse and ends with value VTOTAL at the end of VFP. This value is used
to determine whether we're in blanking period or not, and an adjusted
value of this counter is used to get vpos as expected by
get_scanout_position. Since there is no way to calculate hpos, we always
set it to 0.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!! enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.
Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.
I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NUL for no-name instead of ""
Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
Drivers shouldn't clobber the passed in addfb ioctl parameters.
i915 was doing just that. To prevent it from happening again,
pass the struct around as const, starting all the way from
internal_framebuffer_create().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_MSM_FBDEV config is used to enable/disable fbdev emulation for the
msm kms driver.
Replace this with the top level DRM_FBDEV_EMULATION config option where
applicable. This also prevents build breaks caused by undefined
drm_fb_helper_* functions when legacy fbdev support was disabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the basic MDP5 support for MSM8996.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to produce an image, the scalar needs to be fed extra
pixels. These top/bottom/left/right values depend on a various of
factors, including resolution, scaling type, phase step and
initial phase.
Pixel Extension are programmed by hardware in most targets - and
can be overwritten by software. For some targets (e.g.: msm8996),
software *must* program those registers.
In order to ease this computation, let's always use bilinear
filters, which are easier to program from kernel. Eventually,
all of these values will come down from user space for better
quality.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When calculating phase steps, let's use the same enum
mdp_component_type in order to ease the readability; 0/1 indexes
are a bit confusing and we now have explicit values to index
this type of arrays.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The HDMI controller is new in MDP5 v1.7. As of now, this change
doesn't reflect the novelty and only adds the basics so the probe
gets triggered.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current behavior is to try to get optional clocks and print a
dev_err message in case of failure. This looks rather confusing
and may increase with the amount of optional clocks.
We may need a cleaner way to handle per-device clocks but in the
meantime, let's reduce the amount of dev_err messages during the
probe.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm_iommu_new() can fail and this change makes sure that we
detect the failure and free the allocated domain before going
any further.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We want to make sure we control all the information being passed
down to SMP block. Having access to the cfg pointer here may create
bad things in the future.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current settings for 28nm PHY data lane CFG4 registers do
not work with certain panels. This change is to modify them to
hw recommended values.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In some configurations the supplies are voltage switches and not LDOs,
making the set voltage call to fail. Check with the regulator framework
if the supply can change voltage before attempting.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since
commit 131e663bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 9 23:32:33 2015 +0200
drm/gem: rip out drm vma accounting for gem mmaps
there is no need for this any more.
v2: Fixup compile noise spotted by 0-day build.
Link: http://mid.gmane.org/1444894601-5200-9-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Just one special case (since i915 lost its ums code, yay):
- radeon: Has slots for the old ums ioctls which don't have
DRM_UNLOCKED, but all filled with drm_invalid_op. So ok to drop it
everywhere.
Every other kms driver just has DRM_UNLOCKED for all their ioctls, as
they should.
v2: admgpu happened, include that one too. And i915 lost its UMS
support which means we can change all the i915 ioctls too.
v3: Rebased on top of new vmwgfx DX interface extensions.
v4: Rebase on top of render-node support in exynos.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_count() returns the software counter. We should not pretend
it's the hw counter since we use the hw counter to figuere out what the
software counter value should be. So instead provide a new function
drm_vblank_no_hw_counter() for drivers that don't have a real hw
counter. The new function simply returns 0, which is about the only
thing it can do.
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
[danvet: s/int pipe/unsigned int pipe/ to follow Thierry's interface
change.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the pattern started in commit cc1ef118fc ("drm/irq:
Make pipe unsigned and name consistent"). This is applied to the public
APIs and driver callbacks, so pretty much all drivers need to be updated
to match the new prototypes.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Jianwei Wang <jianwei.wang.chn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV/yX5AAoJEHm+PkMAQRiGUc4IAIFtSt2EORex45d2c64Varjm
4wVJM6k1xz0e8c5bI5D03y/WaefIC2LlKHtWw4+TytnwWEryuGQ1IitvDPZLIntk
I2tUN1IzyxZrJcG2GyfozjxSxeIcaL7us5j7555kEaRVWMamqDaQgVgEKFRqD43N
M4y8qRUeU3OiaL3OhQ9beSfpI/XqjaT+ECGO5HKC3NOJtTrD+cFqLAG9ScCPhvtk
YrrXx3K6J3mylvdvJ5W6JlxOrhFMO+YzViy2bRY8OnAR2vD88p61eT8V2+ENbnMj
+AqXS4HOBpJ6I1Qhff99r0YyvVT/ln9dW7qLAXK3WG27z6HOSWr8KWNUyQD2VLE=
=9yBb
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc2' into topic/drm-misc
Backmerge Linux 4.3-rc2 because of conflicts in the dp helper code
between bugfixes and new code. Just adjacent lines really.
On top of that there's a silent conflict in the new fsl-dcu driver
merged into 4.3 and
commit 844f9111f6
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Wed Sep 2 10:42:40 2015 +0200
drm/atomic: Make prepare_fb/cleanup_fb only take state, v3.
which Thierry Reding spotted and provided a fixup for.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With drivers supporting runtime pm it's generally not a good idea to
touch the hardware when it's off. Add an option to the commit_planes
helper to support this case.
Note that the helpers already add all planes on a crtc when a modeset
happens, hence plane updates will not be lost if drivers set this to
true.
v2: Check for NULL state->crtc before chasing the pointer. Also check
both old and new crtc if there's a switch. Finally just outright
disallow switching crtcs for a plane if the plane is in active use, on
most hardware that doesn't make sense.
v3: Since commit_planes(active_only = true) is for enabling things
only after all the crtc are on we should only look at the new crtc to
decide whether to call the plane hooks - if the current CRTC isn't on
then skip. If the old crtc (when moving a plane) went down then the
plane should have been disabled as part of the pipe shutdown work
already. For which there's currently no helper really unfortunately.
Also move the check for wether a plane gets a new CRTC assigned while
still in active use out of this patch.
v4: Rebase over exynos changes.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Wentao Xu <wentaox@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
With more platforms supported, the DSI host
configuration array keeps expanding. This change
moves those to a separate dsi_cfg module.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On a certain platform, only one type of DSI PHY is used.
This change allows the user to only compile the PHY type
which is being used.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We are not checking the return value from msm_dsi_phy_disable().
Change the return type to void.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bit position to configure source PLL will change
on new types of PHYs. The caller should pass down
this information.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pending interrupt status needs to be cleared before enable the
interrupt. Otherwise it's possible to get a pending interrupt instead
of an incoming interrupt.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 SSPPs can flip the input source horizontally or vertically.
This change is to add this support to MDP5 planes.
v1: Initial change
v2: Use existing "rotation" property instead of creating msm specific
properties. In order to be compatiable with legacy non-atomic
set_property, switch to drm_atomic_helper_plane_set_property
helper function.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Prepare the panel before it's enabled and un-prepare after disable, this
will make sure that the regulators are switched on and off correctly.
Tested it on APQ8064 based IFC6410 with panel.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi bridge ops call drm_panel functions to set up the connected
drm_panel. Add checks to make sure these aren't called when we're
connected to an external bridge.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are platforms where the DSI output can be connected to another
encoder bridge chip (DSI to HDMI, DSI to LVDS etc).
Add support for external bridge support to the dsi driver. We assume that
the external bridge chip would be of the type drm_bridge. The dsi driver's
internal drm_bridge (msm_dsi->bridge) is linked to the external bridge's
drm_bridge struct.
In the case we're connected to an external bridge, we don't need to create
and manage a connector within our driver, it's the bridge driver's
responsibility to create one.
v2:
- Move the external bridge attaching stuff to dsi manager to make things
cleaner.
- Force the bridge to connect to a video mode encoder for now (the dsi
mode flags may have not been populated by modeset_init)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a helper msm_dsi_device_connected() which checks whether we have a
device connected to the dsi host or not. This check gets messy when we
have support external bridges too. Having an inline function makes it
more legible.
For now, the check only consists of msm_dsi->panel being non-NULL. Later,
this will check if we have an external bridge or not.
This helper isn't used in dsi_connector related code as that's specific
to only when a drm_panel is connected.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently support only panels connected to dsi output. We're going to
also support external bridge chips now.
Change 'panel_node' to 'device_node' in the struct msm_dsi_host and
'panel_flags' to 'device_flags' in msm_dsi. This makes things sound a
bit more generic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Platforms containing only DSI video mode devices don't need a TE gpio.
Make TE gpio optional.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently get the output connected to LVDS by looking for a phandle
called 'qcom,lvds-panel' under the mdp DT node.
Use the more standard of_graph approach to create an lvds output port,
and retrieve the panel node from the port's endpoint data.
v3
- Fix return value checks of of_graph_* calls.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi host looks for the connected panel node by parsing for a child
named 'panel'. This hierarchy isn't very flexible. The connected
panel is forced to be a child to the dsi host, and hence, a mipi dsi
device. This isn't suitable for dsi devices that don't use mipi dsi
as their control bus.
Follow the of_graph approach of creating ports and endpoints to
represent the connections between the dsi host and the panel connected
to it. In our case, the dsi host will only have one output port, linked
to the panel's input port.
Update DT binding documentation with device graph usage info.
v3:
- Fix return value checks of of_graph_* calls.
- Don't make port a mandatory DT property
- Fix defer check when no panel node specified
- Rename parse_dt func to align with other dsi_host funcs
Reviewed-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Decrement device node refcount if of_get_child_by_name is successfully
called.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
AHB clock should be enabled before accessing registers during
enable/disable_vblank(). Since these 2 callbacks are called in
atomic context while clk_prepare may cause thread sleep, a work
is scheduled to control vblanks.
v2: fixup spinlock initialization
Signed-off-by: Hai Li <hali@codeaurora.org>
[add comment about cancel_work_sync() before drm_irq_uninstall()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm8x74v1 has different MDP5 version (v1.0) from msm8x74v2 (v1.2).
Add a separate config data to support msm8x74v1.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add planes which use DMA pipes for MDP5.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[slight comment adjust to s/Construct public planes/Construct video
planes/ since DMA planes are public planes too, they just can't scale
or CSC]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP planes can be implemented using different type of HW pipes,
RGB/VIG/DMA pipes for MDP5 and RGB/VG/DMA pipes for MDP4. Each type
of pipe has different HW capabilities such as scaling, color space
conversion, decimation... Add a variable in plane data structure
to specify the difference of each plane which comes from mdp5_cfg data
and use it to differenciate the plane operation.
V1: Initial change
V2: Fix a typo in mdp4_kms.h
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add packed YUV422 and planar YUV420 formats to MDP supported
formats.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Newer MDP5 uses 2 shared memory pool clients for certain YUV formats.
For example, if VIG0 is used to fetch data in YUYV format, it will use
VIG0_Y for Y component, and VIG0_Cr for UV packed.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
[rebase]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
This makes it easy to determine if a format is YUV. The old
method of using chroma sample type incorrectly marks YUV444 as
RGB format.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
[rebase]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reset DSI PHY silently changes its PLL registers to reset status,
which will make cached status in clock driver invalid and result
in wrong output rate of link clocks. The current restore mechanism
in DSI PLL does not cover all the cases. This change is to recover
PLL status after PHY reset to match HW status with cached status
in clock driver.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi_destroy() function was called in two cases by the dsi_init() function
during error handling even if the passed variable contained a null pointer.
* This implementation detail could be improved by adjustments for jump
targets according to the Linux coding style convention.
* Drop an unnecessary initialisation for the variable "msm_dsi" then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[add couple missing ERR_PTR()'s]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi_destroy() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change takes advantage of a HW feature that synchronize
flush operation on CTL1 to CTL0, to keep dual DSI pipes in
sync.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5, CTL contains information of the whole pipeline whose
output goes down to a display interface. In various cases, one
interface may require 2 CRTCs, but only one CTL. Some interfaces
also require to use certain CTLs.
Instead of allocating CTL for each active CRTC, this change is to
associate a CTL with each interface.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add properties alpha/zpos/blend_mode to mdp5 plane
for alpha blending operation to generate the blended output.
v1: Initial change
v2: Change "premultilied" property to enum (Rob's comment)
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[Don't actually expose alpha/premultiplied props to userspace yet
pending a chance for discussion and some userspace to exercise it]
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was a hold-over from the pre-atomic days and legacy userspace that
only understood CRTCs. Fortunately we don't have any properties, so
this doesn't change anything. But before we start growing some plane
properties, we should fix this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY errors are falsely reported whenever a dsi error occurs. This is
because DSI_DLN0_PHY_ERR isn't only used as a status register, but also
used to mask PHY errors. Currently, we end up reading the mask bits too
and therefore always report errors.
Ignore the register mask bits and check for only the status/clear bits.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <hali@codeaurora.org>
For all of these devices, msm89xy was the lead chip, so standardize the
compatible names to align with convention used by rest of the qcom/msm
drivers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the MDP and HDMI support for msm8x94.
Note that HDMI PHY registers are not being accessed anymore from
the driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[rename compatible s/8x94/8994/ since preference is to not trust the
marketing folks who invent chip #'s but instead name things after the
lead chip.. we should rename some 80XY to 89XY to standardize on the
lead chip but leave that for another patch. Also, update dt bindings
doc]
Signed-off-by: Rob Clark <robdclark@gmail.com>
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets use pinctrl framework to configure some
pins. This change allows DSI driver to set default and
sleep pinctrl status.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current term of *dual panel* in DSI driver code causes confusion.
It is supposed to indicate the panel using two DSI links. Rename it
to *dual DSI*.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The source PLL to be used by each DSI PHY should be decided by
DSI manager based on dual DSI information, while the register
programming to select PLL is different from one type of PHY to
another. This change adds the H/W difference to PHY configuration
and updates the interface between DSI manager and PHY.
With this change, PLL selection can be supported on different
targets.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Release all blocks after the pipe is disabled, even when vsync
didn't happen in some error cases. Allow requesting SMB multiple
times before configuring to hardware, by releasing blocks not
programmed to hardware yet for shrinking case.
This fixes a potential leak of shared memory pool blocks.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp4_get_frame_format() can dereference a drm_framebuffer when it's NULL.
Call it in mdp4_plane_mode_set only when we know fb is non-NULL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to return a new sgt, since the caller takes ownership of it.
Reported-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Stephane Viau <sviau@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
