Different modules maybe installed by the user on the eMMC connector
of the odroid-c2. While the red modules are working without an issue,
it seems some black modules (apparently Samsung based) are having
issue at 200MHz
While the tuning algorithm introduced in v4.14 enables high speed modes
on every other tested designs, it seems a problem remains for this
particular combination of board and eMMC module.
Lowering the maximum frequency of the eMMC on this board until we can
figure out a better solution.
Fixes: d341ca88ee ("mmc: meson-gx: rework tuning function")
Suggested-by: Ellie Reeves <ellierevves@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Extend configuring the MAC address from u-boot to all meson boards.
I didn't test this changeset but having checked libretech's u-boot
tree I believe it should just work.
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently one has to look/calculate the GPIO for the PHY interrupts
manually. Add a comment for the existing PHY interrupt lines to make it
easier to find out which GPIO is used.
This is done using the following calculation:
- number of GPIO AO pins (14 on GXBB: GPIOAO_0..13)
- add the offset of the pin which is used for the interrupt (for example
GPIOZ_15 = 15 on Odroid-C2)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-By: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now the VPU Power Domain has been fixed while boothing from Mainline U-Boot,
VPU and HDMI nodes can finally be added to the Odroid-C2 DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the external PHY interrupt on the nanopi-k2, odroid-c2, p200, p230
and q200
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Looking at the schematics, the USB Power Supply is shared between the
two USB interfaces,
If the usb0 fails to initialize, the second one won't have power.
Fixes: 5a0803bd5a ("ARM64: dts: meson-gxbb-odroidc2: Enable USB Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the Data Strobe pin is optional, take it out of the default
eMMC pins and add a separate entry.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
GPIOX22 is now declared properly and TEST_N has been moved so
the gpio-line-names of the odroid-c2 must be adjusted accordingly
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that 3adbf34273 "iio: adc: add a driver for the SAR ADC found in
Amlogic Meson SoCs" has added support for the ADC, let's enable it
on Odroid C2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The ODroid-C2 on-board USB Hub needs to to have it's reset signal set to
high level in order to be enumerated by the USB Host Controller.
But this management must be part of the currently in-development Generic
Power Sequence patch that will allow a USB Controller driver to start and stop
a power sequence associated to the USB Bus.
In the meantime, a simple USB Hog will work to enable the USB Hub.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The wrong GPIO line was provided here.
Fixes: ef8d2ffedf ("ARM64: dts: meson-gxbb: add MMC support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch describes the GPIO lines usage on the Odroid-C2 board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state. While here also explicitly specify the phy-mode instead of
relying on the default-value from meson-gx.dtsi.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
OdroidC2 GbE link breaks under heavy tx transfer. This happens even if the
MAC does not enable Energy Efficient Ethernet (No Low Power state Idle on
the Tx path). The problem seems to come from the phy Rx path, entering the
LPI state.
Disabling EEE advertisement on the phy prevent this feature to be
negociated with the link partner and solve the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current hardware is not able to run with all cores enabled at a
cluster frequency superior at 1536MHz.
But the currently shipped u-boot for the platform still reports an OPP
table with possible DVFS frequency up to 2GHz, and will not change since
the off-tree linux tree supports limiting the OPPs with a kernel parameter.
A recent u-boot change reports the boot-time DVFS around 100MHz and
the default performance cpufreq governor sets the maximum frequency.
Previous version of u-boot reported to be already at the max OPP and
left the OPP as is.
Nevertheless, other governors like ondemand could setup the max frequency
and make the system crash.
This patch disables the DVFS clock and disables cpufreq.
Fixes: 70db166a2b ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Infrared Remote Controller on boards which have an Infrared
receiver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add node for ethernet interface and pinctrl pins.
Enable on odroid-C2 and P20x boards.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT nodes for additional UARTs (UART B & C in EE domain) and add pins
for all EE domain UARTs.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add minimal DT files for the Hardkernel ODROID-C2 board based on the
Amlogic S905/GXBB SoC.
Used the other gxbb boards from Andreas Färber as a starting point.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
